WilTec 61869 User manual
Operation Manual
Planer
ARTICLE 61869
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ
insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities please contact us.
© by WilTec Wildan er Technik GmbH Seite 9
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
The information contained in this document is subject to change without prior notice. o part of this
document can be copied or duplicated in another form without the prior written consent of WilTec
Wildanger Technik GmbH. The WilTec Wildanger Technik GmbH assumes no liability for any errors in
this user manual or the connection diagram.
Although WilTec Wildanger Technik GmbH has made every effort to make sure that this user manual
is complete, accurate and updated, errors cannot always be avoided. In the event of problems with
this user manual please complete and send this form back to us.
FAX-notification (+++49 2403 55592-15),
from: ________________________________________
Name: ________________
Firm:_____________________
Tel/Fax:__________________
I would like to report the followin mistakes:
_______________________________ ____________________________________
Customer Service WilTec Wildanger Technik GmbH
e-mail: [email protected]
Tel:++ +49 2403 55592-0
Introduction
Thank you for purchasing this quality product. To minimize the risk of injury by means of fire or
electric shock we ur e that our clients take some basic safety precautions when usin this
device. Please read the operation instructions carefully and make sure you have understood its
content.
Always use a grounded power connection with the appropriate mains voltage. You can
nd the corresponding mains voltage on the type plate. If you have any doubts about the
connection being grounded, have it checked by a qualied professional. Never use a
faulty electric cable.
o not inspect the electrical part of the pressure pond lter in a wet or damp
environment or when you are wet yourself and protect it from direct sunlight. Install this
device in a safe location so that nobody can step on the cable, fall over or damage it.
isconnect the power plug before cleaning it and use only a damp cloth for cleaning.
Avoid using cleaning agents and make sure that no liquid enters the electrical part of the pump.
The electric part of the device contains no parts that can be inspected or serviced by the user. Leave
the maintenance, adjustment and repair to qualified technical personnel. In case of unauthorised
intervention the 2-year warranty is no longer valid! Keep these operation instructions safe.
© by WilTec Wildan er Technik GmbH Seite 10
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
This tool is intended for planing wooden materials, such as beams and boards, but is also suitable for
chamfering edges and rebating.
TECHNICAL SPECIFICATIONS
PRODUCT ELEMENTS
1. Safety switch
2. On/Off switch
3. Knob for setting planing depth
4. Planing depth indicator
5. Dust port
SAFETY
WAR I G! Read all instructions. Failure to abide by the instructions listed below may result in electric
shock, fire and/or serious injury.
Avoid damage that can be caused by screws, nails and other elements in your workpiece; re-
move them before you start working.
Always make sure to keep the cord away from moving parts of the tool and direct it to the rear
of the tool.
Wait for the cutter block to stop before setting the tool down as an exposed knife may engage
the surface, leading to possible loss of control and serious damage and or injury.
Only use completely undamaged extension cords with a capacity of 16 Amps (UK 13 Amps)
and always ensure that you completely unwind them.
In case of malfunction of any kind, immediately switch off he tool and disconnect the plug.
WilTec can only assure a flawless operation of the tool, if original accessories are used and
the product is used in accordance to the guidelines of this manual.
This tool should not be used by people under the age of 18. 16 years old may only utilise, if
they are under the supervision of an authorised adult familiar with the device and this manual.
Make sure to wear ear protection while using this tool as the noise level when working can ex-
ceed 85 dB(A).
Wear a dust protection mask when working with materials that produce hazardous dust that
can potentially be detrimental to your health and always make sure to inform yourself about
the materials before working with them.
If the cord is damaged or severed while working, touch the cord and immediately disconnect
the plug.
ever use the tool when the cord is damaged in any way. Do not attempt to fix it and instead
have it replaced by a qualified person.
Always check that the voltage indicated on the type plate of the tool corresponds to the supply
voltage (tools with a rating of 230V or 240V can also be connected to a 22V supply).
If a chip should get jammed in the chip outlet, make sure to turn the motor off, ensure that all
moving parts have come to a complete standstill and disconnect the plug before then remov-
ing the jammed chip.
Before using the tool make sure that the knives do not come into contact with any other part of
the device.
Always keep your fingers away from the blades while they are moving.
Always disconnect the device from its power source before making any adjustment or chang-
ing accessories.
WHE CO ECTI G EW 3-PI PLUG (U.K. O LY): Do not connect the blue (= neutral) or
brown (= live) wire in the cord of this tool to the earth terminal of the plug.
If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely. Only
professional technicians are allowed to replace it with a new one.
Your machine is double insulated in accordance with E 50144; therefore no earthwire is required.
© by WilTec Wildan er Technik GmbH Seite 11
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
MAINTENANCE
Make sure that the machine is not connected to the voltage supply when performing maintenance
work on the motor.
Regularly clean the machine housing with a soft cloth, preferably after each use. Keep the ventilation
slots free from dust and dirt. If dirt does not come off, use a soft cloth moistended with soapy water.
ever use solvents, such as petrol, alcohol or ammonia water, as these solvents may damage the
plastic parts. The machine requires no additional lubrication. Should the device malfunction and you
require spare parts, e.g. after wear of a part, please contact your local WilTec.
© by WilTec Wildan er Technik GmbH Seite 12
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
© by WilTec Wildan er Technik GmbH Seite 13
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
© by WilTec Wildan er Technik GmbH Seite 14
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
Disposal re ulations
EU guidelines regarding the disposal of scrap electric appliances (WEEE, 2012/19/EU) were
implemented in the law related to electrical and electronic equipment and appliances.
All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out
wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the
domestic waste.
The company WilTec Technik GmbH has been registrated in the German registry EAR under the
WEEE-registration number DE45283704.
Disposal of used electrical and electronic appliances
(intended for use in the countries of the European
Union and other European countries with a separate
collection system for these appliances).
The logo on the article or on its packaging points out
that this article must not be treated as normal
household waste but must be disposed to a recycling
collection point for electronic and electrical waste
equipment. By contributing to the correct disposal of
this article you protect the environment and the health
of your fellow men. Environment and health are
threatened by inappropriate disposal.
Materials’ recycling helps reduce the consumption of raw materials.
Additional information on recycling this article can be provided by your local community, municipal
waste disposal facilities or the store where you purchased the article.
Address:
WilTec Wildanger Technik GmbH
Königsbenden 12 / 28
D-52249 Eschweiler
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in part of this instructions
manual require the written permission of WilTec Wildanger Technik GmbH.
© by WilTec Wildan er Technik GmbH Seite 15
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
Table of contents
