Winmate FM10 User manual

Please read these instructions carefully before using this product, and save this manual for future use.
Vehicle Mounted Computer
Intel Quad-Core Atom E3845 Processor, 1.91 GHz
FM10
User Guide
Version 6.5
Document Part No. 9152111I100J

1
Chapter 1: Read Me First
Contents
Chapter 1: Read Me First ...........................................................................................................................7
1.1 Informations de sécurité (FR)..............................................................................................................8
1.2 Safety Information (EN).......................................................................................................................8
1.3 About the Adapter..............................................................................................................................9
1.4 Li-Ion Battery.......................................................................................................................................9
1.5 About This Guide ................................................................................................................................9
1.6 General Guideline...............................................................................................................................9
Chapter 2: Introduction............................................................................................................................10
2.1 Package Contents.............................................................................................................................11
2.2 OptionalAccessories.........................................................................................................................11
2.3 Components......................................................................................................................................12
2.3.1 Front View..................................................................................................................................12
2.3.2 Rear View with Vehicle Dock.......................................................................................................13
2.3.3 Side View with Vehicle Dock.......................................................................................................14
2.3.4 Top and Bottom View .................................................................................................................15
Chapter 3: Hardware ................................................................................................................................16
3.1 System Hardware..............................................................................................................................16
3.2 Central Processing Unit.....................................................................................................................16
3.3 Input and Output Connectors............................................................................................................16
3.4 System Memory................................................................................................................................16
3.5 Audio Interface..................................................................................................................................16
3.6 Memory Card....................................................................................................................................17
3.7 WWAN..............................................................................................................................................17
3.8 Power................................................................................................................................................17
3.8.1 Vehicle DC Power Supply...........................................................................................................17
3.8.2 External AC Power Supply (Optional).........................................................................................17
3.9 Power Management Mode................................................................................................................18
3.9.1 Full ON Mode .............................................................................................................................18
3.9.2 Standby and Sleep Mode............................................................................................................18
3.9.3 Hibernate Mode..........................................................................................................................19
3.9.4 OFF Mode ..................................................................................................................................19
3.9.5 Ignition Control ...........................................................................................................................19
3.10 Power Control .................................................................................................................................20
3.10.1 Power Switch............................................................................................................................20
3.10.2 Power Button............................................................................................................................20
3.11 Battery ............................................................................................................................................21
3.11.1 UPS Battery..............................................................................................................................21
3.11.2 Backup Battery.........................................................................................................................22
3.12 External Connectors........................................................................................................................22
3.12.1 Serial Connector (COM) ...........................................................................................................22
3.12.2 USB 2.0 (D-9 Female) Connector .............................................................................................23
3.12.3 CAN Bus / Audio Connector .....................................................................................................23
3.12.4 LAN Connector.........................................................................................................................26
3.12.5 Power Connector......................................................................................................................26
3.13 AntennaConnections......................................................................................................................27
3.12.2 External / Vehicle RemoteAntenna ..............................................................................................27
3.14 Keyboard Options ...........................................................................................................................28
3.15.1 Integrated Keypad ....................................................................................................................28
3.14.2 USB Keyboard / Mouse ............................................................................................................28
3.15 LED Function..................................................................................................................................29
3.15.1 Connection and UPS batteryLEDs...........................................................................................29
3.15.2 System LEDs............................................................................................................................30
3.15.3 Power LED ...............................................................................................................................30
3.15.4 Touch Screen...........................................................................................................................30
3.15.5 Display BacklightControl ..........................................................................................................30

2
FM10 Vehicle Mounted Computer User Guide
Chapter 4: Software..................................................................................................................................31
4.1 Setting Up Windows for the First Time..............................................................................................31
4.2 Setting up Windows 10 IoT Enterprise ..............................................................................................31
4.3 Control Panel....................................................................................................................................34
4.3.1 Using the Touch Screen..............................................................................................................34
4.3.2 Touch Lock.................................................................................................................................37
4.3.3 Turn On/Off the Reading Lamp....................................................................................................38
4.3.4 Volume Adjustment.....................................................................................................................38
4.3.5 Brightness ..................................................................................................................................38
4.3.6 Function Key Form to access F6~F24 ........................................................................................39
4.3 Win-Set Utility ...................................................................................................................................40
4.3.1 System Information.....................................................................................................................40
4.3.2 Win-Set Shortcut Setting.............................................................................................................41
4.3.3 Blanking Function.......................................................................................................................43
4.3.4 Scanner Wedge..........................................................................................................................44
4.3.5 Defroster.....................................................................................................................................44
4.4 Enable BT.........................................................................................................................................46
4.4.1 Opening My Bluetooth ................................................................................................................46
4.5 BT Barcode ReaderSetup ................................................................................................................46
4.5.1 The FM10 with Label..................................................................................................................46
4.5.2 The FM10 without Label .............................................................................................................47
4.5.3 Adding and Pairing a BTDevice .................................................................................................47
4.6 WLAN ...............................................................................................................................................47
4.6.1 External WLAN Antenna.............................................................................................................48
4.6.2 Connecting to a Wireless network...............................................................................................48
4.7 WWAN..............................................................................................................................................49
4.8 Using Camera Features....................................................................................................................51
4.8.1 Opening the Camera ..................................................................................................................51
4.8.2 The Camera Screen ...................................................................................................................51
4.8.3 Shooting Photos.........................................................................................................................51
4.8.4 Recording Videos .......................................................................................................................52
4.8.5 Camera Settings.........................................................................................................................53
4.9 Using Recovery Wizard to RestoreComputer ...................................................................................54
Chapter 5: Accessories Installation ........................................................................................................56
5.1 Installing a SIM Card.........................................................................................................................56
5.2 Installing a Micro SD Card.................................................................................................................57
5.3 Installing a Stylus with the holder......................................................................................................58
Chapter 6: Vehicle Mounting ...................................................................................................................59
6.1 Introduction.......................................................................................................................................59
6.2 Vehicle Mount Instruction..................................................................................................................59
6.3 RAM Mount Installation.....................................................................................................................60
6.4 Docking and Undocking the Device...................................................................................................64
6.5 Power Cable Installation....................................................................................................................64
6.5.1 Wiring the Power Cable..............................................................................................................64
6.5.2 Connecting the Power Cable for Testing.....................................................................................65
6.2.3 Connecting the power cable for installation on the vehicle..........................................................66
6.5.4 Power cable routing....................................................................................................................68
Appendix A: Technical Specifications....................................................................................................69
Appendix B: Order Information ...............................................................................................................70

3
FM10 Vehicle Mounted Computer User Guide
Copyright
No part of this manual may be reproduce, copied, translated, or transmitted in any form or any means,
electronic or mechanical, for any purpose, without the written permission of Winmate Inc.
Trademarks
All product names, trademarks or logos mentioned herein are the properties of their respective owners.
Microsoft, Windows, and the Windows logo are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries. Microsoft products are licensed to OEMs by Microsoft
Licensing, Inc., a wholly owned subsidiary of MicrosoftCorporation.
The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG,Inc.
All other brand and product names are trademarks or registered trademarks of their respectiveowners.
NOTE:
Display images shown may vary slightly from actual display. Information in this manual is
subject to change without prior notification.
NOTE:
FM10 Computer has to be used together with the docking station.
Use the device when located at least 20 cm (7.9 inches) away from the human body.
Disclaimer
Winmate Inc. reserves the right to make any product changes without notice, including circuits and/or
software described or contained in this manual in order to improve design and/or performance. Winmate Inc.
assumes no responsibility or liability for the use of the described product (s), conveys no license or title under
any patent, copyright, or masks work rights to these products, and makes no representations or warranties
that these products are free from patent, copyright, or mask work right infringement, unless otherwise
specified. Applications that are described in this guide are for illustration purposes only. Winmate Inc. makes
no representation or warranty that such applicationwill be suitablefor the specified use without further testing
or modification.
Warranty
Winmate Inc. warrants that each of its products is free from material and workmanship defect for a period of
one year starting from the invoice date. If the customer discovers a defect, Winmate Inc. will, at its option,
repair orreplacethe defective product at nochargetothe customer, provided it is returned during the warranty
period, with transportation charges prepaid. The returned product must be properly packaged in its original
packaging to obtain warrantyservice.

4
FM10 Vehicle Mounted Computer User Guide
Advisory Conventions
Four types of advisories are used throughout the user manual to provide helpful information or to alert you to
the potential for hardware damage or personal injury. These are Notes, Important, Cautions, and Warnings.
The following is an example of each type of advisory.
NOTE:
A note is used to emphasize helpful information
IMPORTANT:
An important note indicates information that is important for you to know.
CAUTION/ ATTENTION
A Caution alert indicates potential damage to hardware and explains how to avoid the
potential problem.
Une alerte d’attention indique un dommage possible à l’équipement et explique comment
éviter le problème potentiel.
WARNING!/ AVERTISSEMENT!
An Electrical Shock Warning indicates the potential harm from electrical hazards and how to
avoid the potential problem.
Un Avertissement de Choc Électrique indique le potentiel de chocs sur des emplacements
électriques et comment éviter ces problèmes.
FCC Regulations
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user‘s authority to operate the equipment.
Operation on the 5.15-5.25GHz frequency band is restricted to indoor use only. The FCC requires indoor use
for the 5.15-5.25GHz band to reduce the potential for harmful interference to co-channel Mobile Satellite
Systems. Therefore, it will only transmit on the 5.25-5.35 GHz, 5.47-5.725 GHz and 5.725 –5.850 GHz band
when associated with an access point (AP).

5
Chapter 1: Read Me First
CE Notice (European Union)
This device has been tested and found to conform to the limits set for a Class B product.
• EN 55022 —“Limits and Methods of Measurement of Radio Interference Characteristics of Information
Technology Equipment”
• EN 55024 —“Information technology equipment - Immunity characteristics - Limits and methods of
measurement”
• EN 61000-3-2 —“Electromagnetic compatibility (EMC) - Part 3: Limits - Section 2”
• EN 61000-3-3 —“Electromagnetic compatibility (EMC) - Part 3: Limits - Section 3”
• EN 60950 —“Safety of Information Technology Equipment”.
• EN 55022 Emissions requirements
RF Exposure Information (SAR)
This device is compliance with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-
1999 and had been tested in accordance with the measurement methods and procedures specified in OET
Bulletin 65 Supplement C.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This device was tested for operations with the device contacted directly to the human body to the back side
of the EUT. To maintain compliance with FCC RF exposure compliance requirements, avoid direct contact
to the transmitted antenna during transmitting.
IC Regulations
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.”
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The device could automatically discontinue transmission in case of absence of information to transmit, or
operational failure. Note that this is not intended to prohibit transmission of control or signaling information or
the use of repetitive codes where required by the technology.
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference
to co- channel mobile satellite systems; the maximum antenna gain permitted (for devices in the bands 5250-
5350 MHz and 5470-5725 MHz) to comply with the e.i.r.p. limit; and The maximum antenna gain permitted
(for devices in the band 5725-5850 MHz) to comply with the e.i.r.p. limits specified for point-to-point and non-
point-to-point operation as appropriate, as stated in section A9.2(3). In addition, High-power radars are
allocated as primary users (meaning they have priority) of the band 5250-5350 MHz and this radar could
cause interference and/or damage to LE-LAN devices.
The County Code Selection feature is disabled for products marketed in the US/Canada. For product
available in the USA/ Canada markets, only channel 1~11 can be operated. Selection of other channels is
not possible.

6
FM10 Vehicle Mounted Computer User Guide
IC Radiation Exposure Statement
This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had
been tested in accordance with the measurement methods and procedures specified in IEEE 1528.

7
Chapter 1: Read Me First
Chapter 1: Read Me First
Follow and adhere to all warnings and instructions in this manual. For your safety, please read all safety
and operating instructions before using the product. Keep this manual for future reference.
CAUTION/ ATTENTION
Pour réduire le risque d’incendie ou de choc électrique ne pas exposer l’appareil à la
pluie ou à l’humidité. VERIFIER que le cordon électrique est la prise murale pour un delai
d’inactivite prolongé. Pour arrêter complètement l’alimentation de l’appareil, débranchez
le cordon d’alimentation de la prise AC. N’enlever ni le capot arrière ni les pièces internes
de l’appareil. Contactez un personnel qualifié si nécessaire.
SA1965
WARNING!/ AVERTISSEMENT!
Utilisé pour les instructions destinés à alerter l’utilisateur d’un CHOC ÉLECTRIQUE
mortel ou de blessure grave en cas d’utilisation incorrecte de l’unité.
SA1966
WARNING!/ AVERTISSEMENT!
Utilisé pour les instructions destinés à alerter l’utilisateur d’un risque mortel ou de
blessure grave en cas d’utilisation incorrecte de l’unité.
CAUTION/ ATTENTION
Pour réduire le risque d’incendie ou de choc electrique ne pas exposer l’appareil à la
pluie ou à l’humidité FAIRE le cordon électrique est DÉBRANCHÉ DE LA PRISE
MURALE DANS UN DELAI DE PROLONGER INACTIVITÉ. De se désengager
totalement LE POUVOIR DE L’UNITE, S’IL VOUS PLAÎT DEBRANCHER LE CORDON
D’ALIMENTATION DE LA PRISE AC. NE PAS Romove le capot arrière, pas de PIÈCES
À L’INTÉRIEUR. Contactez un personnel qualifié S’il faut le réparer.
SA1965
WARNING!/ AVERTISSEMENT!
Sert aux instructions destin es alerter l’utilisateur d’un CHOC ÉLECTRIQUE mortel ou de
blessure grave en cas d’utilisation incorrecte de l’unit.
SA1966
WARNING!/ AVERTISSEMENT!
Sert aux instructions destin es alerter l’utilisateur d’un risque mortel ou de blessure grave
en cas d’utilisation incorrecte de l’unit .

8
FM10 Vehicle Mounted Computer User Guide
1.1 Informations de sé curité (FR)
Suivez et respectez tous les avertissements et instructions figurant sur l’écran. Pour votre sécurité, s’il vous
plaît lire toutes les consignes de sécurité et de fonctionnement avant d’utiliser le device. Gardez ce manuel
pour référence future.
1. Lire avec attention toutes les recommandations et precautions d’emploi avant d’utiliser ce produit.
2. Veuillez conserver ces recommandations et précautions pour référence future.
3. Lire et comprendre tous les avertissements énumérés dans les précautions d’emploi.
4. Suivre toutesles précautions d’emploi pour utiliser ce produit.
5. Utiliser exclusivement un chiffon sec pour nettoyer ce produit.
6. Ne pas placer le produit près de toute source de chaeur telle que radiateurs, arrivées d’air chaud,
fourneaux ou autres appareils générant de la chaleur (incluant les amplificateurs producteurs de
chaleur) .
7. Ne pas négliger la sécurité que procure un branchement polarisé ou avec raccordement à la terre, Un
branchement polarisé comprend deux fiches dont l’une est plus large que l’autre. Un branchement à
la terre comprend deux fiches plus une troisième reliée à la terre. Si la fiche secteur fournie ne s’insert
pas dans votre prise de courant. consulter un ‘électricien afin de remplacer votre prise obsolète.
8. Protéger le cordon d’alimentation de tout écrasement ou pincement, particulièrement au niveau des
fiches, des réceptacles utilisés et à l’endroit de sortie de l’appareil. Ne pas casser la fiche de terre du
cordon d’alimentation.
9. Utiliser uniquement les accessoires spécifiés par le constructeur.
10. Utilisez seulement des accessoires spécifiés par le manufacturier ou vendus avec le
produit.
11. Débrancher cet appareil lors d’orages ou s’il n’est pas utilize pendant une longue
période.
12. Faire exécuter le service par du personnel qualifié. Une intervention technique est requise lorsque
l’appareil a été endommagé ou n’opère pasnormalement.
1.2 Safety Information (EN)
Follow and adhere to all warnings and instructions on the screen. For your safety, please read all safety and
operating instructions before using the device. Keep this manual for future reference.
1. Carefully read all recommendations and precautions for use before using this product.
2. Retain all recommendations and precautions for future reference asnecessary.
3. Read and be sure to understand all warnings listed in the precautions.
4. Follow all operating precautions when using thisproduct.
5. Use only a dry cloth to clean this product.
6. Do not place the product near any heat sources such as radiators, warm air intakes, stoves
or other heat- generating devices (including amplifiers or other heat producing equipment).
7. Do not disregard the safety that a polarized or grounded connection can provide. A polarized
connection consists of two plugs, one of which is larger than the other. A grounded connection
has two blades and a third one that is grounded. If the main plug provided cannot be inserted into
your outlet, consult an electrician to replace your obsolete outlet.
8. Protect the power cord from being crushed or pinched, particularly in the area of the plugs,
any receptacles used, and the point of exit from the apparatus. Do not break off the
ground pin of the power cord.
9. Use only accessories specified by the manufacturer.
10. Use only with accessories specified by the manufacturer or sold with the product.
11. Unplug this apparatus during lightning storms or when it is not being used for long periods.
12. Refer all servicing to qualified service personnel. A technical intervention is required when the
apparatushas been damaged in any way or does not operatenormally.

9
Chapter 1: Read Me First
1.3 About the Adapter
• Use only the supplied AC adapter (Rating: Input DC 10-60V DC). Use of another type of AC adapter will
resultin malfunction and/or danger.
• Do not use the adapter in a high moisture environment. Never touch the adapter when your hands or feet
are wet.
• Allow adequate ventilation around the adapter when using it to operate the device or charge the battery.
Donot cover theAC adapter with paper or other objects that will reduce cooling. Do not usetheAC adapter
while it is inside a carrying case.
• Connect the adapter to a proper power source. The voltage requirements are found on the product case
and/or packaging.
• Do not use the adapter if the cord becomes damaged.
• Do not attempt to service the unit. There are no serviceable parts inside. Replace the unit if it is damaged
or exposed to excessmoisture.
1.4 Li-Ion Battery
Your device has UPS battery. When disposing UPS battery, follow local rules and regulations.
WARNING!
Do not dispose the battery with general waste materials.
The following precautions on battery recycling should be observed:
•The battery should be disposed properly according to local regulations;
•The battery should not be damaged or crushed;
•The battery should not be heated or exposed to direct sunlight.
If you are not aware of local regulations on disposing the battery pack, contact our Service Center or sales
representatives for more information.
IMPORTANT:
This hot-swap battery is soft-packed. It may have up to 8% inflation in dimensions under the
usage in normal conditions. The mechanical design of the device reserves the space for this
normal inflation.
WARNING:
If you observe the internal hot-swap battery has been inflated more than normal condition
(or the blotch of panel and touch caused by inflated battery), contact our Service Center or
sales representative for replacing the battery immediately.
IMPORTANT:
The battery is consumable part. Therefore, it is recommended to replace the battery pack
every two years with a new one recommended by Winmate. Contact our Service Center or
sales representatives for more information on replacing the battery pack.
1.5 About This Guide
This Product Reference Guide provides instruction for the system administrator to follow when configuring
and using the FM10 Vehicle Mount Computer. This Product Reference Guide has been developed for a FM10
with Windows® operating system.
1.6 General Guideline
It is recommended to reboot the device when some functions are defect or inactive. If it still can't solve the
problems, please contact your dealer or agent.

10
FM10 Vehicle Mounted Computer User Guide
Chapter 2: Introduction
In the warehouse environment, the ability to mount mobile devices and computers to forklifts, trucks, taggers,
and inventory pickers, is essential. From inventory management to order fulfillment, asset tracking, and
shipping and receiving, the warehouse floor is complex ecosystem that requires high-efficiency technology to
keep it running smoothly.
The FM10 Vehicle Computer runs on a 1.91GHz Intel ® Atom™E3845 of the full Windows version. The FM10
features GFG resistive touch screen with 1024 x 768 pixel resolution. The FM10 delivers flexibility and mobility
in a vehicle mounted computer form factor. FM10 is designed to easily be removed from the dock with a latch
on the top of the FM10 vehicle docking. Since the dock remains attached to the vehicle, this device can easily
be moved or switched from one vehicle to another vehicle.
The integrated keyboard and physical function keys will appeal to those who prefer the usability of a full
keyboard, but in a vehicle mounted computer form factor. For wireless connectivity the tablet comes equipped
with BT, WLAN, and WWAN.
This vehicle-mount computer is built to endure the rigors of the warehouse, and designed to fit seamlessly
into forklifts and other warehouse vehicles.
NOTE:
Contact our technical support for information on the latest firmware upgrade for your
device.

11
Chapter 2: Introduction
2.1 Package Contents
Before using this device, make sure that all the items listed below are present inyour package:
Computer FM10
Dock + Latch
Locking Key
Power Cable with
Fuse Kit
USB Cable
Power Converter
Cable
Cable Clamp Kit
WLAN Antenna x 2
Quick Start Guide
Driver CD
84W Adapter with
power cable
External Antenna
Fixing Bracket
Power Cord
Stylus Kit
2.2 Optional Accessories
Your package may include the following items based on your order:
DC Jack Power
Cable
RS232 Cable
Audio Cable
CAN BUS Y
Cable
IP65 LAN Cable
WWAN Antenna x
2
15A, 250V, VDA
Type Fuses
Spare Key for
Vehicle Dock
GPS & LTE
2M Combo
Antenna (VM240)
GPS & LTE
5M Combo
Antenna (VM9C)
GPS, LTE, WLAN
Magnetic Combo
Antenna (VM10S)
Mounting Kit 1
No Drill
Mounting Kit 2
Drill
Mounting Kit 3
Keyboard
Mounting
CANBus cable

12
FM10 Vehicle Mounted Computer User Guide
2.3 Components
2.3.1 Front View
No
Item
Description
1
10.4” Touch
Screen
Acts as one of the inputs for thedevice
2
Power Button
Press and hold the button for 3 second to turn on thedevice
Power Indicator
Power Indicator
3
Microphone
For voice communication and voice recording
4
Digital Microphone
For voice communication and voice recording
5
Camera
2 Megapixel front camera
6
Light Sensor
and LED
indicators
Light Sensor
HDD Indicators
Blanking Indicators
Heater Indicators
7
LED indicators
WLAN Indicators
BT Indicators
UPS Battery Indicators
8
Label
Space to print the label or companylogo
9
Function button
Programmable Function key that can be configured by using the Win-Set ®
Utility
10
Speaker
Emits Sound

13
Chapter 2: Introduction
2.3.2 Rear View with Vehicle Dock
No
Item
Description
1
VESA MountHole
VESA 75, 100, and RAM Mount
2
Release Latch
Press to release the device and thedocking
3
Kensington Lock
Connect to a security lock, protecting your device from beingstolen
4
Power switch
Set the switch to on (I) to provide the supply power to the device
and it will automatically connect to the ignition system of thevehicle

14
FM10 Vehicle Mounted Computer User Guide
2.3.3 Side View with Vehicle Dock
Left Side
Right Side
No
Item
Description
1
COM1 and COM2
Connect a peripheral device such as a printer or scanner with serialport
2
USB 2.0 x 2
Connect USB peripheral devices such as USB Flash drive, mouse,
keyboard,
printer, etc.
3
CAN Bus / Audio
Connect to a vehicle, allowing access to wide range of vehicledata/
Connects headphone or other audio output devices.
4
Service Window*
To protect I/O ports
5
LAN Port
Connect to a local area network (LAN) using an Ethernet cable.
6
Wide Range Power Input
Connect a 10-60V DC IN wide range power input
7
WWAN Antenna
Connector
Connect a WWAN external antenna and allow the device to be remotely
mounted on the vehicle
8
GPS Antenna Connector
Connect a GPS external antenna and allow the device to be remotely
mounted on the vehicle.
9
WLAN Antenna
Connector
Connect a WLAN external antenna and allow the device to be remotely
mounted on the vehicle
*Service window covers SD Card Slot/ SIM Card Slot, USB3.0 and DC in power input jack.

15
Chapter 2: Introduction
2.3.4 Top and Bottom View
No
Item
Description
1
Lock
Lock the tablet in place
2
Reading Light
Use to provide illumination in darkenvironment

16
FM10 Vehicle Mounted Computer User Guide
Chapter 3: Hardware
3.1 System Hardware
3.2 Central Processing Unit
The FM10 is running an Intel Atom E3845 processor 1.91 GHz, and the operating system of this device is
Windows 10.
3.3 Input and Output Connectors
The FM10 device supports the following I/O connectors:
•SIM Card Slot
•Micro SD Card Slot
•USB 3.0
•DC In Power Input Jack
The Vehicle Dock of the FM10 device supports the following I/O connectors:
•COM Port
•USB 2.0
•CAN BUS/ Audio Connector
•LAN Port
•Wide Range Power Input
3.4 System Memory
The main system memory is 4GB SODIMM DDR3L-1600 (up to 8GB).
3.5 Audio Interface
Your device is equipped with two speakers which are located on the bottom of the vehicle dock.Amicrophone
is also available for voice communication and voicerecording.
As an alternative, you can use a headset adapter cable that provides a connection for headset operation.
When headset is plugged in to the adapter cable, the main speakers or internal microphone will be disabled.

17
Chapter 3: Hardware
3.6 Memory Card
Your device has a memory card slot which accepts an SD memory card. The memory card is hotswappable.
Your device has an 802.11 a/b/g/n/ac network card that can be used with internal or externalantennas.
3.7 WWAN
Using a SIM card for network connection, your device supports Wireless Wide Area Networking (WWAN).
3.8 Power
3.8.1 Vehicle DC Power Supply
The Power input voltage range for the vehicle dock is between 10 to 60V DC, without the need to perform
any manual operation within the vehicle dock.
This dock provides conditioned power output for the device. By using a specified DC to DC adapter, the input
voltage
of 100-240 V DC nominal can be accepted.
3.8.2 External AC Power Supply (Optional)
If the DC power is not available, you can use an optional external UPS (Universal Input Power Supply) to
convert AC power to an appropriate DC level.
Using an external UPS and adapter cable, the AC to DC power input for the device is transferred to the
vehicle dock.
To perform the connection, simply plug one end of the adapter cable to the dock and then plug the other end
of the adapter cable to the DC output cable from adapter. For Details, refer to the connection diagram shown
below:
No
Item
1
AC Input Cable
2
DC Output Cable
3
To DC Output Cable
4
To FM10

18
FM10 Vehicle Mounted Computer User Guide
3.9 Power Management Mode
The FM10 has four power modes:
•Full ON
•Standby / Sleep
•Hibernate
•OFF
Action
Button
Power Button
Backlight
Indicator
Turn On
Press the On button for “2
seconds” until the battery indicator
On (solid green) and then release
the button
Off
Standby or
Sleep
Mode *
Press the On button for “2
seconds” until the screen On and
then release the button. The
battery indicator will Off after the
screen is Off, the system is already
in the standby / sleep mode
On
Wake up
Press the On button for “2 second”
until the screen On and then
release the button. The battery
indicator will On (solid green)
Off
Turn Off
Press the On button for “4 second”
until the system is turns Off and
then releases the button.
Off
3.9.1 Full ON Mode
When the FM10 is attached to either vehicle power or an external power supply, or it is operating from the
UPS batteryand the power button is pressed, thedevice is in the “ON” mode. In this mode, the keypad, touch
screen and any attached peripherals will function normally.The display remains ON until the display, standby
or hibernate timer expires.
When the device is in ON mode, the power LED indicators isoff.
3.9.2 Standby and Sleep Mode
When the Standby / Sleep timer expires without a primary event occurring, the device transitions to standby
/ Sleep mode. Press the power button to wake up the device back to ONmode.
When the device is in Standby / Sleep mode, the power LED indicator isred.

19
Chapter 3: Hardware
3.9.3 Hibernate Mode
When the device is in Hibernate Mode, all LEDs are off. Press the power button to wake up the device back
to ON mode.
When the device is in Hibernate mode, the power LED indicator isred.
3.9.4 OFF Mode
By default, the FM10 turns off if the user turns off the device through the system or presses the power button
for 8 seconds with a critical shut down. The FM10 will also be off when there is no connection to a power
source or the UPS battery is depleted. However the internal RTC will keep maintaining the date and time
while the device is off. When the device is off, the power LED indicator isred.
3.9.5 Ignition Control
Winmate provides Ignition Software AP to control the timing of delay. Users are able to select 1 to 120
secondsfor each period of timing delay. To setup the timing delay please follows these steps:
On Delay: Default 10 seconds. When the system is powered on via ignition key, the system will delay 10
seconds to power on.
Off Delay: Default 10 seconds. When the system is powered off via ignition key, the system will delay 10
seconds to shut down.
Hard Off Delay: Default 30 seconds. When the system is powered off via ignition key, the device will cut off
power after 30 seconds.
No
Setting
Default Setting
Description
1
On Delay
10 seconds
When the system is powered on via ignition key, the system will
delay 10 seconds to power on.
2
Hard Off Delay
30 seconds
When the system is powered off via ignition key, the device will
cut off power after 30 seconds.
3
Off Delay
10 seconds
When the system is powered off via ignition key, the system will
delay 10 seconds to shut down.
4
Reset to default
-
Resets the ignition settings back to the default.