Winmate FM-V Series User manual

Vehicle Mounted Computer
Intel Elkhart Lake x6425E Processor, 2.0 GHz
10.4”/ 12.1”/ 14”
FM-V Series
User Guide
Version 1.2
Document Part No. 9152111I1150

1
Contents
Contents
Chapter 1: Read Me First ...........................................................................................................................7
1.1 Informations de sécurité (FR)..............................................................................................................8
1.2 Safety Information (EN).......................................................................................................................8
1.3 About the Adapter..............................................................................................................................9
1.4 Li-Ion Battery.......................................................................................................................................9
1.5 General Guideline...............................................................................................................................9
Chapter 2: Introduction............................................................................................................................10
2.1 Package Contents.............................................................................................................................11
2.2 OptionalAccessories.........................................................................................................................11
2.3 Components......................................................................................................................................12
2.3.1 Front View with FM10E-V...........................................................................................................12
2.3.2 Front View with FM12E-V...........................................................................................................13
2.3.3 Front View with FM14E-V...........................................................................................................14
2.3.4 Rear View with FM10E-V and FM12E-V......................................................................................15
2.3.5 Rear View with FM14E-V............................................................................................................16
2.3.6 Side View ...................................................................................................................................17
2.3.7 Top and Bottom View .................................................................................................................18
Chapter 3: Hardware ................................................................................................................................19
3.1 Central Processing Unit.....................................................................................................................19
3.2 Input and Output Connectors............................................................................................................19
3.3 System Memory................................................................................................................................19
3.4 Memory Card....................................................................................................................................19
3.5 WLAN ...............................................................................................................................................19
3.6 WWAN(Optional)...............................................................................................................................19
3.7 Power Cable Installation....................................................................................................................20
3.7.1 Wiring the Power Cable..............................................................................................................20
3.7.2 Connecting the Power Cable for Testing.....................................................................................20
3.7.3 Connecting the power cable for installation on the vehicle..........................................................21
3.8 Power Management Mode................................................................................................................23
3.8.1 Full ON Mode .............................................................................................................................23
3.8.2 Standby and Sleep Mode............................................................................................................23
3.8.3 Hibernate Mode..........................................................................................................................23
3.8.4 OFF Mode ..................................................................................................................................24
3.8.5 Ignition Control ...........................................................................................................................24
3.9 Power Control ...................................................................................................................................25
3.9.1Power Button...............................................................................................................................25
3.10 Battery ............................................................................................................................................26
3.10.1 UPS Battery..............................................................................................................................26
3.10.2 Backup Battery.........................................................................................................................27
3.11 External Connectors........................................................................................................................28
3.11.1 Serial Connector(COM1 & COM2)............................................................................................28
3.11.2 DIDO / Serial Connector (COM1) (Optional).............................................................................29
3.11.3 Audio / Serial Connector (COM1) (Optional).............................................................................30
3.11.4 CAN Bus / Serial Connector (COM2) (Optional) .......................................................................31
3.11.5 USB 2.0 Connector...................................................................................................................32
3.11.6 LAN Connector.........................................................................................................................32
3.11.7 Power Connector......................................................................................................................32
3.12 External / Vehicle RemoteAntenna .................................................................................................33
3.13 Keyboard Options ...........................................................................................................................34
3.13.1 Integrated Keypad for FM10E-V ...............................................................................................34
3.13.2 Integrated Keypad for FM12E-V ...............................................................................................35

2
FM-V Series Vehicle Mounted Computer User Guide
3.13.3 Integrated Keypad for FM14E-V ...............................................................................................36
3.13.4 SB Keyboard / Mouse...............................................................................................................36
3.14 LED Function..................................................................................................................................37
3.14.1 Power LED ...............................................................................................................................38
3.14.2 Display BacklightControl ..........................................................................................................38
Chapter 4: Software..................................................................................................................................39
4.1 Setting Up Windows for the First Time..............................................................................................39
4.2 Setting up Windows 10 IoT Enterprise ..............................................................................................39
4.3 Control Panel....................................................................................................................................42
4.3.1 Using the Touch Screen..............................................................................................................42
4.3.2 Touch Lock.................................................................................................................................43
4.3.3 Volume Adjustment.....................................................................................................................44
4.3.4 Brightness ..................................................................................................................................44
4.3.5 Function Key Form to access F6~F24 ........................................................................................45
4.4 Win-Set Utility ...................................................................................................................................46
4.4.1 System Information.....................................................................................................................46
4.4.2 Win-Set Shortcut Setting.............................................................................................................47
4.4.3 Blanking Function.......................................................................................................................49
4.4.4 Scanner Wedge..........................................................................................................................50
4.4.5 Defroster(Optional).....................................................................................................................51
4.5 Ignition Software AP..........................................................................................................................52
4.5.1 DIDO Controller..........................................................................................................................52
4.5.2 COM port Controller....................................................................................................................53
4.6 BT.....................................................................................................................................................54
4.6.1 Opening My Bluetooth ................................................................................................................54
4.7 BT Barcode ReaderSetup ................................................................................................................54
4.7.1 The VMC with Label ...................................................................................................................55
4.7.2 The VMC without Label...............................................................................................................55
4.7.3 Adding and Pairing a BTDevice .................................................................................................55
4.8 WLAN ...............................................................................................................................................55
4.8.1 Connecting to a Wireless network...............................................................................................56
4.9 WWAN(Optional)...............................................................................................................................57
4.10 Using Camera Features ..................................................................................................................59
4.10.1 The Camera Screen .................................................................................................................59
4.10.2 Shooting Photos.......................................................................................................................59
4.10.3 Recording Videos......................................................................................................................60
4.10.4 Camera Settings.......................................................................................................................61
4.11 Using Recovery Wizard to RestoreComputer..................................................................................62
Chapter 5: Accessories Installation........................................................................................................64
5.1 Installing a SIM Card.........................................................................................................................64
5.2 Installing a Micro SD Card.................................................................................................................65
Chapter 6: Vehicle Mounting ...................................................................................................................66
6.1 Vehicle Mount Instruction..................................................................................................................66
6.2 RAM Mount Installation.....................................................................................................................66
Appendix A: Technical Specifications....................................................................................................71
FM10E-V.................................................................................................................................................71
FM12E-V.................................................................................................................................................72
FM14E-V.................................................................................................................................................73

3
FM-V Series Vehicle Mounted Computer User Guide
Copyright
No part of this manual may be reproduce, copied, translated, or transmitted in any form or any means,
electronic or mechanical, for any purpose, without the written permission of Winmate Inc.
Trademarks
All product names, trademarks or logos mentioned herein are the properties of their respective owners.
Microsoft, Windows, and the Windows logo are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries. Microsoft products are licensed to OEMs by
Microsoft Licensing, Inc., a wholly owned subsidiary of Microsoft Corporation.
The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
NOTE:
Display images shown may vary slightly from actual display. Information in this manual is
subject to change without prior notification.
NOTE:
Use the device when located at least 20 cm (7.9 inches) away from the human body.
Disclaimer
Winmate Inc. reserves the right to make any product changes without notice, including circuits and/or
software described or contained in this manual in order to improve design and/or performance. Winmate Inc.
assumes no responsibility or liability for the use of the described product (s), conveys no license or title
under any patent, copyright, or masks work rights to these products, and makes no representations or
warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified. Applications that are described in this guide are for illustration purposes only. Winmate
Inc. makes no representation or warranty that such application will be suitable for the specified use without
further testing or modification.
Warranty
Winmate Inc. warrants that each of its products is free from material and workmanship defect for a period of
one year starting from the invoice date. If the customer discovers a defect, Winmate Inc. will, at its option,
repair or replace the defective product at no charge to the customer, provided it is returned during the
warranty period, with transportation charges prepaid. The returned product must be properly packaged in
its original packaging to obtain warrantyservice.

4
FM-V Series Vehicle Mounted Computer User Guide
Advisory Conventions
Four types of advisories are used throughout the user manual to provide helpful information or to alert you
to the potential for hardware damage or personal injury. These are Notes, Important, Cautions, and
Warnings. The following is an example of each type of advisory.
NOTE:
A note is used to emphasize helpful information
IMPORTANT:
An important note indicates information that is important for you to know.
CAUTION/ ATTENTION
A Caution alert indicates potential damage to hardware and explains how to avoid the
potential problem.
Une alerte d‘attention indique un dommage possible à l‘équipement et explique comment
éviter le problème potentiel.
WARNING!/ AVERTISSEMENT!
An Electrical Shock Warning indicates the potential harm from electrical hazards and how to
avoid the potential problem.
Un Avertissement de Choc Électrique indique le potentiel de chocs sur des emplacements
électriques et comment éviter ces problèmes.
FCC Regulations
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user‗s authority to operate the equipment.
Operation on the 5.15-5.25GHz frequency band is restricted to indoor use only. The FCC requires indoor
use for the 5.15-5.25GHz band to reduce the potential for harmful interference to co-channel Mobile
Satellite Systems. Therefore, it will only transmit on the 5.25-5.35 GHz, 5.47-5.725 GHz and 5.725 –5.850
GHz band when associated with an access point (AP).

5
FM-V Series Vehicle Mounted Computer User Guide
CE Notice (European Union)
This device has been tested and found to conform to the limits set for a Class B product.
• EN 55022 —―Limits and Methods of Measurement of Radio Interference Characteristics of
Information Technology Equipment‖
• EN 55024 —―Information technology equipment - Immunity characteristics - Limits and methods of
measurement‖
• EN 61000-3-2 —―Electromagnetic compatibility (EMC) - Part 3: Limits - Section 2‖
• EN 61000-3-3 —―Electromagnetic compatibility (EMC) - Part 3: Limits - Section 3‖
• EN 60950 —―Safety of Information Technology Equipment‖.
• EN 55022 Emissions requirements
RF Exposure Information (SAR)
This device is compliance with SAR for general population /uncontrolled exposure limits in ANSI/IEEE
C95.1-1999 and had been tested in accordance with the measurement methods and procedures specified
in OET Bulletin 65 Supplement C.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This device was tested for operations with the device contacted directly to the human body to the back side
of the EUT. To maintain compliance with FCC RF exposure compliance requirements, avoid direct contact
to the transmitted antenna during transmitting.
IC Regulations
Le présent appareil est conforme aux CNR d‘Industrie Canada applicables aux appareils radio exempts de
licence. L‘exploitation est autorisée aux deux conditions suivantes:
(1) l‘appareil ne doit pas produire de brouillage, et
(2) l‘utilisateur de l‘appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d‘en compromettre le fonctionnement.‖
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation
of the device.
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The device could automatically discontinue transmission in case of absence of information to transmit, or
operational failure. Note that this is not intended to prohibit transmission of control or signaling information
or the use of repetitive codes where required by the technology.
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful
interference to co- channel mobile satellite systems; the maximum antenna gain permitted (for devices in
the bands 5250-5350 MHz and 5470-5725 MHz) to comply with the e.i.r.p. limit; and The maximum antenna
gain permitted (for devices in the band 5725-5850 MHz) to comply with the e.i.r.p. limits specified for point-
to-point and non-point-to-point operation as appropriate, as stated in section A9.2(3). In addition, High-
power radars are allocated as primary users (meaning they have priority) of the band 5250-5350 MHz and
this radar could cause interference and/or damage to LE-LAN devices.
The County Code Selection feature is disabled for products marketed in the US/Canada. For product
available in the USA/ Canada markets, only channel 1~11 can be operated. Selection of other channels is
not possible.

6
FM-V Series Vehicle Mounted Computer User Guide
IC Radiation Exposure Statement
This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and
had been tested in accordance with the measurement methods and procedures specified in IEEE 1528

7
Chapter 1: Read Me First
Chapter 1: Read Me First
Follow and adhere to all warnings and instructions in this manual. For your safety, please read all safety
and operating instructions before using the product. Keep this manual for future reference.
CAUTION/ ATTENTION
Pour réduire le risque d‘incendie ou de choc électrique ne pas exposer l‘appareil à la pluie
ou à l‘humidité. VERIFIER que le cordon électrique est la prise murale pour un delai
d‘inactivite prolongé. Pour arrêter complètement l‘alimentation de l‘appareil, débranchez le
cordon d‘alimentation de la prise AC. N‘enlever ni le capot arrière ni les pièces internes de
l‘appareil. Contactez un personnel qualifié si nécessaire.
SA1965
WARNING!/ AVERTISSEMENT!
Utilisé pour les instructions destinés à alerter l‘utilisateur d‘un CHOC ÉLECTRIQUE mortel
ou de blessure grave en cas d‘utilisation incorrecte de l‘unité.
SA1966
WARNING!/ AVERTISSEMENT!
Utilisé pour les instructions destinés à alerter l‘utilisateur d‘un risque mortel ou de blessure
grave en cas d‘utilisation incorrecte del‘unité.
CAUTION/ ATTENTION
Pour réduire le risque d‘incendie ou de choc electrique ne pas exposer l‘appareil à la pluie
ou à l‘humidité FAIRE le cordon électrique est DÉBRANCHÉ DE LA PRISE MURALE
DANS UN DELAI DE PROLONGER INACTIVITÉ. De se désengager totalement LE
POUVOIR DE L‘UNITE, S‘IL VOUS PLAÎT DEBRANCHER LE CORDON
D‘ALIMENTATION DE LA PRISE AC. NE PAS Romove le capot arrière, pas de PIÈCES À
L‘INTÉRIEUR. Contactez un personnel qualifié S‘il faut le réparer.
SA1965
WARNING!/ AVERTISSEMENT!
Sert aux instructions destin es alerter l‘utilisateur d‘un CHOC ÉLECTRIQUE mortel ou de
blessure grave en cas d‘utilisation incorrecte de l‘unit.
SA1966
WARNING!/ AVERTISSEMENT!
Sert aux instructions destin es alerter l‘utilisateur d‘un risque mortel ou de blessure grave
en cas d‘utilisation incorrecte de l‘unit .

8
FM-V Series Vehicle Mounted Computer User Guide
1.1 Informations de sé curité (FR)
Suivez et respectez tous les avertissements et instructions figurant sur l‘écran. Pour votre sécurité, s‘il vous
plaît lire toutes les consignes de sécurité et de fonctionnement avant d‘utiliser le device. Gardez ce manuel
pour référence future.
1. Lire avec attention toutes les recommandations et precautions d‘emploi avant d‘utiliser ce produit.
2. Veuillez conserver ces recommandations et précautions pour référence future.
3. Lire et comprendre tous les avertissements énumérés dans les précautions d‘emploi.
4. Suivre toutesles précautions d‘emploi pour utiliser ce produit.
5. Utiliser exclusivement un chiffon sec pour nettoyer ce produit.
6. Ne pas placer le produit près de toute source de chaeur telle que radiateurs, arrivées d‘air chaud,
fourneaux ou autres appareils générant de la chaleur (incluant les amplificateurs producteurs de
chaleur) .
7. Ne pas négliger la sécurité que procure un branchement polarisé ou avec raccordement à la terre, Un
branchement polarisé comprend deux fiches dont l‘une est plus large que l‘autre. Un branchement à la
terre comprend deux fiches plus une troisième reliée à la terre. Si la fiche secteur fournie ne s‘insert
pas dans votre prise de courant. consulter un ‗électricien afin de remplacer votre prise obsolète.
8. Protéger le cordon d‘alimentation de tout écrasement ou pincement, particulièrement au niveau des
fiches, des réceptacles utilisés et à l‘endroit de sortie de l‘appareil. Ne pas casser la fiche de terre du
cordon d‘alimentation.
9. Utiliser uniquement les accessoires spécifiés par le constructeur.
10. Utilisez seulement des accessoires spécifiés par le manufacturier ou vendus avec le
produit.
11. Débrancher cet appareil lors d‘orages ou s‘il n‘est pas utilize pendant une longue période.
12. Faire exécuter le service par du personnel qualifié. Une intervention technique est requise lorsque
l‘appareil a été endommagé ou n‘opère pasnormalement.
1.2 Safety Information (EN)
Follow and adhere to all warnings and instructions on the screen. For your safety, please read all safety and
operating instructions before using the device. Keep this manual for future reference.
1. Carefully read all recommendations and precautions for use before using this product.
2. Retain all recommendations and precautions for future reference as necessary.
3. Read and be sure to understand all warnings listed in the precautions.
4. Follow all operating precautions when using thisproduct.
5. Use only a dry cloth to clean this product.
6. Do not place the product near any heat sources such as radiators, warm air intakes, stoves or other
heat- generating devices (including amplifiers or other heat producing equipment).
7. Do not disregard the safety that a polarized or grounded connection can provide. A polarized
connection consists of two plugs, one of which is larger than the other. A grounded connection has two
blades and a third one that is grounded. If the main plug provided cannot be inserted into your outlet,
consult an electrician to replace your obsolete outlet.
8. Protect the power cord from being crushed or pinched, particularly in the area of the plugs, any
receptacles used, and the point of exit from the apparatus. Do not break off the ground pin of the
power cord.
9. Use only accessories specified by the manufacturer.
10. Use only with accessories specified by the manufacturer or sold with the product.
11. Unplug this apparatus during lightning storms or when it is not being used for long
periods.
12. Refer all servicing to qualified service personnel. A technical intervention is required
when the apparatushas been damaged in any way or does not operatenormally.

9
Chapter 1: Read Me First
1.3 About the Adapter
• Use only the supplied AC adapter (Rating: Input DC 10-60V DC). Use of another type of AC adapter
will resultin malfunction and/or danger.
• Do not use the adapter in a high moisture environment. Never touch the adapter when your hands or
feet are wet.
• Allow adequate ventilation around the adapter when using it to operate the device or charge the
battery. Do not cover the AC adapter with paper or other objects that will reduce cooling. Do not use
the AC adapter while it is inside a carrying case.
• Connect the adapter to a proper power source. The voltage requirements are found on the product
case and/or packaging.
• Do not use the adapter if the cord becomes damaged.
• Do not attempt to service the unit. There are no serviceable parts inside. Replace the unit if it is
damaged or exposed to excess moisture.
1.4 Li-Ion Battery
Your device has UPS battery.The UPS battery is only expected to use for backup under low system loading
and without I/O function. When disposing UPS battery, follow local rules and regulations.
WARNING!
Do not dispose the battery with general waste materials.
The following precautions on battery recycling should be observed:
The battery should be disposed properly according to local regulations;
The battery should not be damaged or crushed;
The battery should not be heated or exposed to direct sunlight.
If you are not aware of local regulations on disposing the battery pack, contact our Service Center or sales
representatives for more information.
IMPORTANT:
This hot-swap battery is soft-packed. It may have up to 8% inflation in dimensions under the
usage in normal conditions. The mechanical design of the device reserves the space for this
normal inflation.
WARNING:
If you observe the internal hot-swap battery has been inflated more than normal condition (or
the blotch of panel and touch caused by inflated battery), contact our Service Center or sales
representative for replacing the battery immediately.
IMPORTANT:
The battery is consumable part. Therefore, it is recommended to replace the battery pack
every two years with a new one recommended by Winmate. Contact our Service Center or
sales representatives for more information on replacing the battery pack.
1.5 General Guideline
It is recommended to reboot the device when some functions are defect or inactive. If it still can't solve the
problems, please contact your dealer or agent.

10
FM-V Series Vehicle Mounted Computer User Guide
Chapter 2: Introduction
In the warehouse environment, the ability to mount mobile devices and computers to forklifts, trucks,
taggers, and inventory pickers, is essential. From inventory management to order fulfillment, asset tracking,
and shipping and receiving, the warehouse floor is complex ecosystem that requires high-efficiency
technology to keep it running smoothly.
The FM-V Series Vehicle Computer runs on a 2.0GHz Intel®AtomTM x6425E of the full Windows version.
This Series features a compact panel with a PCAP touch screen. The FM-V Series VMC offer cost
efficiency and device reliability by eliminating the need for a vehicle dock station and offer an all-in-one
computer with integrated IO ports.The all-in-one in-vehicle computer has an integrated WWAN, WLAN, and
BT function that easily pairs the vehicle mount computer with customers' barcode scanner and enterprise
system for quick data collection.
This vehicle-mount computer is built to endure the rigors of the warehouse, and designed to fit seamlessly
into forklifts and other warehouse vehicles.
NOTE:
Contact our technical support for information on the latest firmware upgrade for your
device.

11
Chapter 2: Introduction
2.1 Package Contents
Before using this device, make sure that all the items listed below are included in your package:
Vehicle
Mounted
Computer
Power Cable with
Fuse
84W Adapter
with Power
Cable
Quick Start
Guide
Power
Converter
Cable
Power Cord
2.2 Optional Accessories
Your package may include the following items based on your order:
DC Jack Power
Cable
RS232 Cable
LAN Cable
WWAN Antenna
Fuse Kit
GPS Antenna
GPS & LTE
(VM240)
GPS & LTE
(VM9C)
GPS & LTE
(VM10S)
USB Type A
Cable
Comport +
Canbus
Comport + DIDO
Stylus Kit
Mounting Kit 1
No Drill
Mounting Kit 2
Drill
Mounting Kit 3
Keyboard Mounting

12
FM-V Series Vehicle Mounted Computer User Guide
2.3 Components
2.3.1 Front View with FM10E-V
No
Item
Description
1
10.4‖ Touch Screen
Acts as one of the inputs for thedevice
2
Camera
2 Megapixel front camera
3
Microphone
For voice communication and voice recording
4
Power Button and
Indicator
Press and hold the button for 3 second to turn on thedevice
5
Light Sensor and
LED indicators
Light Sensor
HDD Indicators
Blanking Indicators
Heater Indicators
6
Function buttons
Programmable Function keys that can be configured by using the Win-Set®
Utility
7
LED indicators
Wi-Fi Indicators
Bluetooth Indicators
UPS Battery Indicators
8
Digital Microphone
For voice communication and voice recording
9
Label
Space to print the label or companylogo

13
Chapter 2: Introduction
2.3.2 Front View with FM12E-V
No
Item
Description
1
12.1‖ Touch Screen
Acts as one of the inputs for thedevice
2
Camera and
Microphone
2 Megapixel front camera with a microphone for voice communication and
voice recording
3
Light Sensor and
LED indicators
Wireless communication indicators
Defroster indicators (Defroster is customized feature available by
request)
UPS Battery Indicators
HDD indicators
Light sensor
4
Power Button and
Indicator
Press and hold the button for 3 second to turn on thedevice
5
Function buttons
Programmable Function keys that can be configured by using the Win-Set®
Utility
Digital Microphone
For voice communication and voice recording

14
FM-V Series Vehicle Mounted Computer User Guide
2.3.3 Front View with FM14E-V
No
Item
Description
1
14‖ Touch Screen
Acts as one of the inputs for the device
2
Camera
2 Megapixel front camera
3
Microphone
For voice communication and voice recording
4
Light Sensor and
LED indicators
Wi-Fi Indicators
UPS Battery Indicators
HDD Indicators
Power Indicator

15
Chapter 2: Introduction
2.3.4 Rear View with FM10E-V and FM12E-V
No
Item
Description
1
VESA Mount Hole
VESA 75, 100, and RAM Mount

16
FM-V Series Vehicle Mounted Computer User Guide
2.3.5 Rear View with FM14E-V
No
Item
Description
1
Power Button
Press and hold the button for 3 second to turn on the device
2
Function buttons
Programmable Function keys that can be configured by using the Win-
Set® Utility
3
VESA Mount Hole
VESA 75, 100, and RAM Mount

17
Chapter 2: Introduction
2.3.6 Side View
No
Item
Description
1
LAN Port
Connect to a local area network (LAN) using an Ethernet cable
and provide optional PSE with 30W.
2
D-SUB A: DB9 male with
COM1
Connect a peripheral device such as a printer or scanner with
serialport . There is 5V DC output on pin 9.
D-SUB A: DB15 male with
COM1+DIDO/Audio
(Optional)
DIDO connector allows direct linking into vehicle, enable
access to wide range of vehicle data.
Audio connector allows connecting headphone or other audio
output devices.
3
USB Type-A
Connect USB peripheral devices such as USB Flash drive,
mouse, keyboard, printer, etc.
4
Wide Range Power Input
Connect a 10-60V DC IN wide range power input
5
D-SUB B: DB9 male with
COM2
Connect a peripheral device such as a printer or scanner with
serialport .There is 5V DC output on pin 9.
D-SUB B: DB15 female
with COM2+CANBus
(Optional)
CANBus connector allows direct linking into vehicle, enable
access to wide range of vehicle data
6
SD Card Slot
Service window to insert MicroSD card.
7
Dual Nano SIM Card Slot*
Service window to insert Nano SIM cards.
8
USB Type-C
A high-speed USB port connects to USB devices.
Note: Service window covers SD Card Slot/ SIM Card Slot and USB Type-C.
Note: For the defroster function please connect a device to a power supply.

18
FM-V Series Vehicle Mounted Computer User Guide
2.3.7 Top and Bottom View
No
Item
Description
1
WWAN Antenna
Connector(optional)
(Optional)
Connect a WWAN external antenna and allow the device to be
remotely mounted on the vehicle.
2
GPS Antenna
Connector(optional)
Connect a GPS external antenna and allow the device to be
remotely mounted on the vehicle.