WittRock P0052 User manual

© 2013 by WittRock Healthcare Services, Inc. ALL RIGHTS RESERVED.
No part of this text shall be reproduced without written permission from WittRock Healthcare
Services, Inc. May 14, 2013 150685 REV 4 Page 1 of 38
Subject: P0052 Bed Locator Installation Instructions
Tools required: Standard drill 1/4" and 5/8" diameter drill bits
Phillips head screwdriver Screwdriver
5/16" hex nut driver Tape measure
Level Power screwdriver
As-built drawings Stud finder
Safety glasses Broom
Dustpan Pencil
Parts required: (1) 131617 Installation guide bracket
(1) 149814 Bag assembly, Bed Locator
(4) 50590 Screw, #6-20, oval, cross head, recessed
(1) P005270 Flatwall Headwall System interconnect (for
units installed with the Flatwall Headwall
System only)
(1) P2102AT0052B Basis®1Headwall System interconnect (for
units installed with the Basis® Headwall
System only)
(1) M21020069 Bag assembly, Bed Locator 1 gang mud ring
149814, Bag assembly, Bed Locator, includes these items:
(6) 16114 Screw, #6-32 x ½", phillips, flat head, zinc-
plated, full thread
(6) 29591 Screw, #8, self-drilling
(4) 5294502 Screw, #6 x 3/8", type B, truss head
(9) 5314301 Screw, #12—self-drilling, hex head
(6) 55408 Grommet edging, 2"
(6) 55409 Grommet edging, 3"
(3) 55691PL Face ring, wall box
(2) 50854-03 Screw
(4) 57185 Wall anchor
(4) 55138 Screw (for wall anchor)
(8) 16115 Screw (installed on assembled bed locator)
(4) 50590 Screw (installed on assembled bed locator)
(2) 3869 Washer
(12) 52553 Cable tie
1. Basis® is a registered trademark of WittRock Healthcare Services, Inc.

Page 2 of 38 150685 REV 4 May 14, 2013
P005270, Flatwall Headwall System interconnect, includes these items:
(1) 55217 Bag assembly, interconnect
(1) 149457 Raceway cover, Flatwall Headwall System
interconnect
(1) 149456 Backplate, Flatwall Headwall System
interconnect
55217, Bag assembly, Flatwall interconnect, includes these items:
(1) 12483 Lockwasher, #8, dish-type
(1) 15359 Washer, 16 gauge, unplated
(1) 15384 Toggle snap, 3/16", zinc-plated
(1) 50167 Screw, #10-24 x 3", round/cross head
(5) 5294502 Screw, #6 x 3/8", type B, truss head
P2102AT0052B, Basis® Headwall System interconnect, includes these
items:
(1) 171958 Backplate, Basis® Headwall System
interconnect
(1) 172133 Bed locator interconnect cover
(1) 177674 Bag assembly, Basis interconnect
177674, Bag assembly, Basis interconnect, includes these items:
(2) 16115 Screw, #6-20 x 3/8", type B, flat head
(1) 12483 Lockwasher, #8, dish-type
(1) 15359 Washer, 16 gauge, unplated
(1) 15384 Toggle snap, 3/16", zinc-plated
(1) 50167 Screw, #10-24 x 3", round/cross head
(4) 5294502 Screw, #6 x 3/8", type B, truss head
M21020069, Bag assembly, Bed Locator 1 gang mud ring, includes these
items:
(6) 134037 Screw, #8-32 x 1.25", type F, phillips pan
head
(6) 16115 Screw, #6-20 x 3/8", type B, flat head
(9) 58551 Screw, 1/4", self-drilling, hex head
(3) 179179 Bed Locator, wall panel face ring
(6) 179178 Bed Locator, wall panel sleeve
Introduction
These instructions are for the installation of the P0052B Locator on standard, fire-rated, or
seismic-rated dry wall and with these products:
• Flatwall Headwall System (P670E)
• ImageBuilders®1Cabinet Headwall Collection (P796)
• Basis® Headwall System (P2102A)
1. ImageBuilders® and Basis® are registered trademark of WittRock Healthcare Services, Inc.

May 14, 2013 150685 REV 4 Page 3 of 38
• Basis® Wall Panel System
WARNING:
Except when mounted to cabinetry (minimum 3/4" (19 mm) thick plywood or
particleboard core), wall-mounted bed locators shall be mounted to walls that
are constructed of 5/8" (16 mm) minimum dry wall on 20-gauge minimum steel
studs that are center-spaced to a maximum of 16" (41 cm). Failure to do so
could cause injury or equipment damage.
NOTE:
The decorative plastic cover has a Smoke Index rating between 500 and 632.
Install the bed locator in accordance with all applicable national, state or provincial, and local
codes, and the latest editions of these:
For USA installations National Fire Protection Association®1(NFPA):
• NFPA 70: National Electrical Code® (NEC®) and NFPA 99: Health Care
Facilities
For Canadian installations Canadian Standards Association (CSA®2) (applicable to a
stand-alone unit only):
• CSA C22.1 and C22.2, Parts I and II of the Canadian Electrical Code
• CSA Z32: Electrical Safety and Essential Electrical Systems in Health
Care Facilities
• CSA Z318.0: Commissioning of Health Care Facilities
Radiated and Conducted Emissions (EMC): The P0052B3 Medical Headboard with LED
lighting (see Figure-8) is powered by a factory installed 12 V DC, 500 ma fuse limited,
WittRock Healthcare 149425 Power Supply Unit (Rated Input: 120/240 V AC, 2 A, 50/60
Hz). This 15 Watt ITE power supply may also be used as a remote DC power source in
WittRock Healthcare speci-fied applications. When connected and used in accordance with
WittRock Healthcare instructions, the WittRock Healthcare®3P0052B Bed Locator with
149425 Power Supply Unit is compliant to the Class-A requirements of Part-15 in Title-47 of
the US Code of Federal Regulations
(47CFR-15) and, when installed as a stand-alone unit, the Industry Canada ICES/NMB-003
standard.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the Federal Communications Commission (FCC) rules. These
limits are designed to provide reasonable protection against harmful interference when the
1. National Fire Protection Association®, National Electrical Code®, and NEC® are registered trade-
marks of National Fire Protection Association, Inc.
2. CSA® is a registered trademark of Canadian Standards Association, Inc.
3. WittRock Healthcare® is a registered trademark of WittRock Healthcare Services, Inc.

Page 4 of 38 150685 REV 4 May 14, 2013
equipment is operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equip-
ment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at his own expense.
This Class-A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de
la classe A est conforme à la norme NMB-003 du Canada.
NOTE:
Changes or modifications to equipment not expressly approved in writing
by WittRock Healthcare could void the user's authority to operate the
equipment.
Setup
1. Before you start the installation, refer to the as-built drawings to determine the correct
location for the bed locator.
2. Make sure the facility’s power has been run to the installation site and the wall boxes,
where applicable, have been installed in the wall or center cabinet of the
ImageBuilders® Cabinet Headwall Collection.
3. Unpack the contents of the shipping container.
4. Read all of these installation instructions, and make sure the instructions match your
hardware and as-built drawings.
SHOCK HAZARD:
Turn off all power to the installation site. Failure to do so could cause injury or
equipment damage.
5. Turn off all power to the installation site.
NOTE:
The installation site is likely to have more than one grounded power source: normal
power and emergency power.
Determine the Wall and Construction Type
WARNING:
The installation method differs for each wall and construction type. Failure to
install the bed locator according to the applicable wall and construction type
could cause the bed locator to collapse. Injury or equipment damage could
occur.
1. Refer to the local or state building codes, and determine the wall type and construction
type:

May 14, 2013 150685 REV 4 Page 5 of 38
•Seismic walls are constructed to prevent damage from an earthquake.
•Fire-rated walls are constructed to prevent the spread of fire.
2. Do one of these:
• For seismic walls, install wall backing plates according to the Office of
Statewide Health, Planning, and Development (OSHPD)-approved drawings
and the as-built drawings, and then go to “Hardware Requirements” on page 5.
• For fire-rated, non-seismic walls, make sure the walls are constructed with at
least 20-gauge steel studs on 16" (41 cm) centers and covered with a minimum
of 5/8" (16 mm) dry wall, and then go to “Hardware Requirements” on page 5.
Hardware Requirements
1. Remove the necessary hardware from the bag assembly (see figure 1 on page 5):
• For seismic-rated or fire-rated dry wall hardware, refer to table 1 on page 6.
• For the ImageBuilders® Cabinet Headwall Collection hardware, refer to
table 2 on page 6.
• For the Wall Panel System hardware, refer to table 3 on page 6.
Figure 1. Hardware

Page 6 of 38 150685 REV 4 May 14, 2013
Table 1. Seismic-Rated and Fire-Rated Dry Wall Hardware
Table 2. ImageBuilders® Cabinet Headwall Collection
Table 3. Wall Panel System Hardware
Item Part Number Description
A 5314301 Screw, #12-14 x 1 ½", self-drilling, hex
head
B 29591 Screw, #8-18 x ½", self-drilling
F 16114 Screw, #6-32 x ½", phillips, flat head, zinc-
plated
G 5294502 Screw, #6 x 3/8", type B, truss head
H 12483 Lockwasher, #8 dish-type
I 15359 Washer, 16 gauge, unplated
J 50167 Screw, #10-24 x 3", round/cross head
K 15384 Toggle snap, 3/16", zinc-plated
L 5085403 Screw, #8-15 x 5/8", pan head
M 55138 Screw, #8-18 x 5/8", pan head
N 57185 Anchor, screw
BG 16115 Screw, #6-20 x 3/8", type B, flat head
Item Part Number Description
A 5314301 Screw, #12-14 x 1 ½", self-drilling, hex
head
B 29591 Screw, #8-18 x ½", self-drilling
F 16114 Screw, #6-32 x ½", phillips, flat head, zinc-
plated
L 5085403 Screw, #8-15 x 5/8", pan head
Item Part Number Description
B 29591 Screw, #8-18 x ½", self-drilling
BG 16115 Screw, #6-20 x 3/8", type B, flat head
BK 134037 Screw, #8-32 x 1 1/4", type F, phillips pan
head
BM 58551 Screw, 1/4", self-drilling, hex head

May 14, 2013 150685 REV 4 Page 7 of 38
2. If you install the bed locator with a Flatwall Headwall System or Basis® Headwall
System, get the hardware from the interconnect module.
Removal of the Plastic Cover from the Backplate Assembly
1. Remove the two screws (E) that attach the face plates (AN) through the plastic cover
(D) to the backplate assembly (R). (see figure 2 on page 7)
2. Remove the face plates (AN) from the backplate assembly (R).
3. Remove the plastic cover (D) from the backplate assembly (R).
4. Remove the four screws (AH) that attach the front panel (AM) to the backplate assem-
bly (R).
5. Remove the front panel (AM) from the backplate assembly (R).
Figure 2. Removal of the Plastic Cover from the Backplate Assembly
Which Instructions to Use
1. Do one of these:
• If you install the bed locator on a wall as a stand-alone unit, go to “Install the
Bed Locator as a Stand-Alone Unit” on page 9.

Page 8 of 38 150685 REV 4 May 14, 2013
• If you install the bed locator with the Flatwall Headwall System, go to
“Install the Bed Locator with the Flatwall Headwall System” on page 13.
• If you install the bed locator on the ImageBuilders® Cabinet Headwall
Collection, go to “Install the Bed Locator on the ImageBuilders® Cabinet
Headwall Collection” on page 17.
• If you install the Medical Headboard as a stand alone unit, go to “Install the
Medical Headboard as a Stand-Alone Unit” on page 20.
• If you install the bed locator with the Basis® Headwall System, go to “Install
the Bed Locator with the Basis® Headwall System” on page 23.
• If you install the bed locator on the Wall Panel System, go to “Install the Bed
Locator as a Stand Alone Unit on the Wall Panel System” on page 28.

May 14, 2013 150685 REV 4 Page 9 of 38
Install the Bed Locator as a Stand-Alone Unit
1. Install the flat head screws (F) to attach the face rings (P) on the line voltage and low
voltage wall boxes (Q) (see figure 3 on page 9).
Figure 3. Backplate Assembly and Installation Guide Bracket
2. Remove the knockouts from the backplate assembly (R) that align with the wall boxes
(Q).
3. Install the grommet edging around each removed knockout.
4. Make a mark to show the bed centerline (S) (see figure 4 on page 10):
a. Refer to the as-built drawings, and determine the bed centerline (S) as it relates
to the backplate assembly (R).
b. If a finished floor has not been installed, make a mark to show the location of
the intended finished floor line (T).
c. Make a plumb vertical bed centerline (S) on the wall 25" (64 cm) up from the
floor line (T).
d. The bottom edge of the locator will be 9 1/2" (24.13 cm) from the floor line.

Page 10 of 38 150685 REV 4 May 14, 2013
Figure 4. Bed Locator—Typical Installation Dimensions