WiXHC MACH3 MK-ET Series User manual

MACH3 Ethernet Breakout Board
Support CNC System:
Mach3 only
MK3-ET：3 Axis Ethernet breakout board
MK4-ET：4 Axis
MK6- ：6 Axis Ethernet breakout board
Ethernet breakout board
ET
Product Size：184x127x30mm
MKX-ET Specification
QC:01 2016-9-13
电源0V电源24V
适合系统：Mac h3系统
产品型号：MK4-ET
产品名称：Mach3以太网控制卡
硬件程序版本：
-1-

English Manual
Features:
Fully supporting all Mach3 versions,support Windows PC,
Only support Ethernet interface,Need to set IP address
(Please read the last page for reference)
Support save data when power off
Support spindle speed feedback
Support 10 meters Ethernet interface cable
Supports Up 6-axis
Maximum step-pulse frequency is 2000KHz
16 general-purpose input,8 output
Velocity feedback function, Spindle speed display in real time
all IO-port isolation, interference, stable performance
Support servo motor and step motor
★
★
★
★
★
★
★
★
- 2 -
★
★
ChengDu XinHeCheng Technology Co.,Ltd

电源0V电源24V
Simp le connection description
Application Connection Diagram
Spindle drive
Spindle
MACH3
TOOLS
probe
Input switch
Relays
Drive
Motor
Ethernet Motion Control Card Application
POWER
INPUT
Support: 3-axis or 4-axis, or 6-axis
Mk3-ET: 3-axis; Mk4-ET: 4-axis: Mk6-ET: 6-axis
- 3 -
QC:01
适合系统 ：Mach 3系统
产品型号：MK4- ET
产品名称 ：Mac h3以太 网控制 卡
硬件程序 版本 ：
2016-9-13
ChengDu XinHeCheng Technology Co.,Ltd

Signal Description
0V-INPUT
power In
24V Input
output 8
Y-axis
0V-output
output 7
output 6
output 5
output 4
output 3
output 1
Z-axis A-axis
DIR-
DIR+
PUL+
X-axis
Digital Ground
Forward:
16 Input port
X-axis home(input-#0)
Probe z(input-#4)
5V PWM output
Analog ground
DC 10V Input
Frequency Control Input：0-10V
input -#5
Power LED
0v ouput
24V ouput
Y-axis home(input-#1)
Z-axis home(input-#2)
A-axis home(input-#3)
input -#6
input -#7
input -#8
input -#9
input -#10
input -#11
input -#12
input -#13
input -#14
input -#15
Spindle control
Light: Work fine
Slow flash: Connect
successfully
Off: The USB connection
is not normal
ChengDu XinHeCheng Technology Co.,Ltd
output 2
Reversion:
24V ouput
- 4 -
ETHERNET MOTION CARD
电源0V电源24V
PUL-
DIR-
DIR+
PUL+ PUL-
DIR-
DIR+
PUL+ PUL-
DIR-
DIR+
PUL+ PUL-
QC:01
适合系统：Mac h3系统
产品型号：MK4- ET
产品名称：Mach3以太网控制卡
硬件程序版本：
2016-9-13

ETHERNET MOTION CARD
电源0V电源24V
Wiring diagram shows
NOTE: If the inverter is turned on, the control card is not working properly because of interference caused
by the inverter ; Replace inverter.
24V Power Input
Step or servo driver
Relay
Computer
NPN Photoelectric switch
OUT
GND
VCC
Mechanical switch
Inverter
Inverter forward signal
Digital signal ground
Inverter 10V output
0-10V analog voltage
Analog signal ground
Mechanical switch
Input IO Connect NPN (PNP) Photoelectric switchMechanical switch or
Input signal must be active low
OUT
GND
VCC
PNP Photoelectric switch
Relay
OUT
GND
VCC
hall switch
-5-
DIR-
PUL-
DIR+
PUL+
QC:01
适合系统：Mac h3系统
产品型号：MK4- ET
产品名称：Mach3以太网控制卡
硬件程序版本：
2016-9-13
ChengDu XinHeCheng Technology Co.,Ltd

Electrical Characteristics
0—10V
5V,1KHZ,Duty;0-100%
Parameter Description
Drive Current Isolated open collector output; 5V, 20mA
Drive Pulse + direction output
Output frequency 2000KHZ
axes MK3-ET:3-axis;MK4-ET:4-axis;MK6-ET:6-axis
Isolation Voltage
Analog voltage output
PWM output
Pulse+direction output 5V,15HZ to 4KHZ
Isolation:50mA, 25V
Isolated inputs, 5 mA, maximum voltage 25V
3.5KV
Drive Current
Isolation Voltage 3.5KV
Input Current
Isolation Voltage 3.5KV
axis output
control:
Spindle inverter
output:
3 types of output
modes
8 IO output
16 IO intput
-6-
ChengDu XinHeCheng Technology Co.,Ltd

Software installation
First,Install Mach3 software to your PC.
- 7 -
ChengDu XinHeCheng Technology Co.,Ltd
Second, copy our driver into mach3.Check file in the CDreadme
Check our wiring for ref er ence, connec t our car d to your machi ne cor rect ly
Connect your PC to our card by using network cable
After these steps, you can open your Mach3 software for operating
Please take a look at mach3 software parame ters setting,Step per and
so on in the printed ma nual of our packing box for reference.

DC 24V-INPUT
DC 0V_GND
MKX Wiring
DC24V,0.5A
Drive connection.
2.
1.
- 8 -
Offer power supply to our card
Our card support Servo or stepper drive, Differential output signal
ChengDu XinHeCheng Technology Co.,Ltd

MKX Wiring
Connected to the machine housing
power supply
+10v
0 TO 10v
AVI
Analog gnd
ACM
FwD
forward on/off
digital gnd
DCM
变频器10V输出
变频器模拟信号输入
模拟信号地线
变频器正转控制
数字信号地
保护地线
PE
变频器调速接口
Speed adjustment
变频器数字接口
Digital Interface
inverter
Inverter wiring for reference
NO.3：
- 9 -
ChengDu XinHeCheng Technology Co.,Ltd

MKX Wiring
Spindle connected stepper or servo drives
stepper or servo drives
PUL+
PUL-
DIR+
DIR-
0V
NO.4：
Relay
Output active low,24v\ 50 mA
Output Relay Interface：OUT3 to OUT8 Relay Interface
5V5V
5V and 0V connect
to our card 5V and
0V
-10-
ChengDu XinHeCheng Technology Co.,Ltd

MKX Wiring
Input Io：16 Input port;In0 to In15.Active Low
NO.5：
NPN photoelectric switch
OUT
GND
VCC
Mechanical Switch
OUT
GND
VCC
PNP photoelectric switch
Relay
- 1 1 -
ChengDu XinHeCheng Technology Co.,Ltd

New Function
When our control card suddenly power off, the control card chip
automatically save the current G code line number. Control card
plug-in display save the number of lines.
Wait until the control card is connected to the power supply next,
load the G code program, click the power to continue to the break
continue button, Mach3 software automatically from the last save
the number of lines to start running.
-12-
ChengDu XinHeCheng Technology Co.,Ltd
G-code line quantity save function

Current Spindle rotary speed send to our card port“Speed-DEC”,
then display RPM speed on Mach3.Maximum support feedback input
Pulse frequency 20KHZ.
Spindle speed feedback
- 1 3 -
First step: the computer IP address setting.
New Function
ChengDu XinHeCheng Technology Co.,Ltd
<Ethernet card directly connected to the computer> Please
open“network sharing center”,select the “local connection -
property”,open"Internet protocol version 4 (TCP/IPV4)", and
manual input IP address 192.168.1.xx(XX from 0-179, can not
be repeated)

If your Ethernet card is connected to your computer via a router,
Please make sure your router IP address format is 192.168.1.xx ,
If not, modify your router IP address into 192.168.1.xx format.
Otherwise unable to communicate. Modify the IP address of the
router, and then manually set the IP address of the computer in
accordance with the above method.
After PC IP address is set up, open the Mach3
software "plug-in control"in the figure below the location of the
choice of a IP address, range: 180-195.(If you have only one set of
control card, skip this setting. Factory defaults IP:180)
Ethernet card connected to the router
The second step: Ethernet card Mach3 software IP address Setting
-14-
New Function

- 1 5 -
if you only connected with 1 set of our Ethernet control card, skip the
step. IP factory default is 180 open Ethernet control card control card
circuit board in the shell, the upper inner has a red dial switch, a total
of 4 of them. You can set the IP, range: 0-15, corresponding to the IP
address of the Mach3 software plug-in control: 180-195.default all
dial switch goes to the ON position, IP address is 0, corresponding
to Ethernet IP of Mach3 software: 180 Refer to the following table
settings:
The third step: IP internal Ethernet switch setting
拨码开关设置
Dial switch setting
对应Mach3软件IP地址
Mach3 software IP
IP:180
IP:181
New Function

拨码开关设置
Dial switch setting
对应Mach3软件IP地址
Mach3 software IP
IP:182
IP:183
IP:184
IP:185
IP:186
IP:187
-16-
New Function

拨码开关设置
Dial switch setting
对应Mach3软件IP地址
Mach3 software IP
IP:188
IP:189
IP:190
IP:191
IP:192
IP:193
- 1 7 -
New Function

拨码开关设置
Dial switch setting
对应Mach3软件IP地址
Mach3 software IP
IP:194
IP:195
-18-
New Function

6
-19-