WLtoys q222g User manual

CONTENTS OF THE BOX:
• 1 x Quadcopter
• 1 x 2.4 GHz remote (6x AA-batteries not included)
• 1 x 3.7V 730 mAh Li-po battery
• 4 x Spare propeller
• 1 x Charger
• 1 x Manual
• 4 x prop guards
SPECIFICATIONS:
• 2.4GHz Assembled quadcopter drone Ready-to-fly
• 6-axis Gyroscope
• 4 main engines
• 1 Li-po Battery 3.7V 730mAh
• Height: 58 mm
• Length: 375 mm
• Width: 136 mm
• Weight: 900 g
Security precautions
DO NOT FLY:
- Around people or animals
- Around large groups of people
- In limited visibility or dark conditions
- Winds above 2 Beaufort
- Near high voltage pylons and / or other types of cabling
- During thunderstorms, rain or high humidity. The device is not water-resistant.
Battery recycling recommendations
• Read the manual carefully and completely
• This model is not suitable for children under 14 years and contains small parts
• Children should only use this model under the supervision of an adult
• The model and the transmitter must be switched off after use
• Always fly in an open and safe environment where you will not cause any danger to others
• For the remote control, we recommend AA batteries with a voltage of 1.5 to 1.2 volts
• Keep these instructions safe
• Always follow local laws and regulations! Contact your reseller when in doubt.
We highly recommend to use the propguards we provide with each model. This will not only protect your quadcopter, but also
other people, your house interiour, walls and all other surroundings that could get injured or damaged if you lose control during
flights.
For the sensitive and rational conservation, protection and improvement of the quality of the environment, protection of human
health and the preservation of natural resources, the user must send an unusable product to relevant facilities created to this
purpose in accordance with the law.
The crossed out wheelie bin means that the product must be recycled (WARNING: do not throw it in your bin).
• After using the copter ALWAYS disconnect the battery and remove it from the device
• For people without experience, we recommend that you learn to fly with an experienced user during your first flights
• Stand out of reach of moving parts of the copter
• Keep hands, face, hair and clothes away from blades.
• Before each flight, test the distance limit of the transmitter
Prop guards
Specifications
INSTRUCTION MANUAL
Copyright WLtoys.eu | DroneX BV

The user must return used batteries and rechargeable batteries.
It is forbidden to dispose of used batteries in the bins containing
household waste! Batteries / accumulators containing
hazardous substances are marked with the crossed out wheelie
bin. The symbol indicates that the product should be recycled.
The chemical symbols for the respective hazardous substances
are Cd (cadmium), Hg (mercury), Pb (lead). The used batteries
can be disposed for free of charge at collection points in your
community, stores or wherever batteries are sold. You are kindly
requested to conform to your legal obligations and contribute to
the protection of our environment.
1. Charging wire
2. LED
3. Li-po Battery
Plug the charger into a wall socket and connect the battery to
the charger. This can only be done in one way: by firmly
connecting the charging cable. If the green light is on, the
battery is fully charged and can be disconnected. Then do not
forget to unplug the charger from the wall socket.
Green LED = Charged battery
Orange LED = Charging battery
Red LED = Battery is empty / Charging battery
Input : 220V
Charging Current : 500mA
Full Voltage: 4.2 +/- 0.03V
- Keep the batteries out of reach of children
- Unequally charged batteries or different battery types should not be used together
- Use recommended batteries or similar
Li-po Battery instructions
Battery charging
Warning : Always place the battery on a heat resistant surface and never leave it unattended!
- Do not charge directly after the flight or when the battery is warm
- Non-rechargeable batteries should not be recharged
- After using the copter, remove the batteries if you will not use it again for a long period of time
- This model is equipped with a rechargeable Li-po Battery. Li-po batteries require special attention, follow the manual
- The batteries must be charged with the charger supplied by WLtoys
- Always charge the battery to 100%
- Ensure that the battery wires are not in contact to avoid a short-circuit
- The ignition wires of the battery must not be modified or damaged
- Never damage the battery mechanically (this could cause an explosion)
- The terminals must not be short-circuited
- The battery should not be placed near children (unless you have an adult supervision)
- The technical design of the battery must not be changed
- Touching of damaged batteries can cause injury. If there is contact with skin or eyes, seek medical attention immediately!
- Do not leave charging without supervision
- When charging the battery, always ensure that you do so on a non-combustible surface
Copyright WLtoys.eu | DroneX BV

1. Power LED
2. Module 1 : Water jet; bubble jet; video; basket up; lead
single missile
3. Throttle/Yaw control stick
4. Throttle trim
5. Yaw trim
6. 40% agility
7. 60% agility
8. 80% agility
9. LCD display
10. Power switch
11. Antenna
12. Roll (when 100%)
13. Direction control stick
14. Forwards and backwards trim
15. Crab trim
16. 100% agility
17. Lighting control
18. Module 2 : Taking photos(Headless mode if available,
press 2 sec)
1. Stick mode 1/3 indicator
2. Throttle trim tips
3. Yaw trim tips
4. Percentage of the reaction
5. Transmitter battery indicator
6. Stick mode 2/4 indicator
7. Forwards and backwards trim tips
8. Crab trim tips
Insert the battery by sliding the cover down. Then insert 6 x AA
batteries as indicated under the cover.
Remote Control / Transmitter
- Using the throttle you can control the rotation axis of the drone. Using the directional joystick you can control the flight direction
of the drone.
- The mode available on this model is the mode 2 with the layout of the throttle on left. It is not possible to switch mode on this
model.
- The different calibration buttons help keep the drone stationary. Test this by pressing the accelerator and calibration buttons to
maintain the drone in one place.
- You can choose the percentage of the speed. The higher the value, the faster the reaction will be (e.g. 100% will be more
responsive than 40%).
- The two module buttons are used to activate different modules : photos / shots / basket.
Copyright WLtoys.eu | DroneX BV

SIDEWARD
The directional lever serves to move the drone to the left or
the right.
FORWARD
Pushing the directional lever up and down makes your
drone go forward or backward.
Altitude hold
How to fly
Flying is really simple, but you need a little practice at first. Connect to www.wltoys.eu to watch educational films.
- Turn on the remote
This model is equipped with a barometer. The barometer allows the quadcopter to hold altitude without using the remote.
- Trottle up and it will fly to approx 1m altitude and maintain hight
- Keep light button (middle right) pressed for 1sec and it will autoland
- Arm the quad by moving trottle to left bottom and direction to right bottom
- Adjust altitude with throttle up/down
Starting the copter:
- Connect the battery to the copter.
- Alternatively throttle down and when it is securily landed disarm the quad by moving trottle to left bottom and direction to right
- By holding it down for more than 2 sec. you use the throttle to make height. By holding it down for just one seconde, the copter
- Trottle up/down to connect drone to remote
Ending:
Copyright WLtoys.eu | DroneX BV

ALTITUDE
Pushing the gear lever up and down makes your altitude
rise or fall.
TURN
Pushing the gear lever from side to side, the drone will turn
on its own axis.
Procedure to spare engine
The first flight
1. For your first flight make sure to be with a person experienced in flying copters. We advise you to make your first flights on a
relatively soft surface to protect the copter.
2. Find a location away from people, with a smooth surface and without obstacles. Trees, electric lines and water points in the
immediate vicinity should be avoided!
3. Place your copter on the ground about 10 feet away from you. Mind that, when you have a quadcopter, the coloured blades
indicate the front of the copter. It is easiest to position yourself behind the copter for an easier control.
4. Turn the copter on first. Then turn on the remote controll (for some models this will be the other way around) for the V333N,
turn on the copter as well as the controller. then move trottle up and down to connect. after this move throttle to the left low corner
and the directional lever to the right lower corner at the same time, hold these down for a few seconds, this will arm the motors.
5. Start the engine and take off to about 1 meter from the ground. In this way you avoid the phenomenon called "ground effect".
Near the ground the air currents behave differently than at a higher altitude and this will prevent you from losing control of the
copter.
6. Then try to fly gently in one direction. If the engine flies away in the wrong direction, make a controlled landing and try again.
Engines are brushed and eventually wear out. When worn out they need to be replaced. For more informations go to
www.wltoys.eu.
Never go full speed for the first 3 flights. After 3 flights, blow out engines with air when possible.
Spare engines can be bought on www.wltoys.eu or with your reseller.
CAUTION
- Ensure that the copter in flight is always within sight and under control.
Copyright WLtoys.eu | DroneX BV

1. The receiver LED blinks continuously for more than 4 seconds after the quadcopter battery have been inserted. No response to
the command input. The transmitter is not connected to the device. Repeat the power-on initialization process.
2. No response from the quadcopter after the battery have been connected. There is probably contact failure on the battery
terminals. Turn on the transmitter and ensure that the battery of the vehicle is correctly inserted. Replace the battery and ensure
good contact at the battery's connections. Use fully charged batteries in the remote.
3. The motor does not respond to the throttle stick and the receiver flashes. The quadcopter's battery is exhausted. Charge the
battery or replace it with a charged battery.
4. The main rotor continues to rotate after landing. Confirm that the gear lever is oriented downward.
5. The main rotor rotates but the device does not take off. The blades may be distorted or the quadcopter battery is exhausted.
Charge or replace with a fully charged battery and / or replace the blades.
6. The quadcopter suffers of strong vibrations. The blades are distorted. Replace the blades.
7. The tail is not balanced after adjusting the clip or speed is inconsistent in the left / right pirouette. Tail rotors are probably
damaged. Replace the main wing and / or the main engine.
8. The quadcopter was still moving forward after the adjustment of the levers during hover. The gyroscope is not correctly
calibrated. The gear lever is placed too high or too low. The boot refines the calibration therefore restart on a flat surface.
9. You can not fly, the helicopter falls. The motor is probably fall out or the gears are loose. Reinstall the motor and tighten the
gears.
Calibration
If the copter is unstable, resulting in frenetic flying in all directions, and rotates around its axis so that you have to constantly
correct its flight, then the gyroscope is probably not calibrated properly. To perform recalibration, connect the drone to the
transmitter (part Activation in the manual), then click on 100% button of the remote and move both sticks to the bottom left. When
the calibration is performed, you will either hear a long beep or see flashing lights (on the PCB) or both.
Note: The calibration is done in the factory, it is usually not necessary to do it when you receive the product.
The copter is not sensitive to crashes, but in case of extreme drops it is possible that some parts may break. All parts can be
ordered and easily assembled. Please contact your dealer or visit www.wltoys.eu for more information.
Troubleshooting
Spare parts
FPV
- When finished flying, always turn off the copter first, then the remote control.
- Remember to disconnect the battery of the copter after each flight.
- Always fly in an open and Jellyfished environment to avoid dangerous situations.
- Always use a fully charged battery.
- Do not use the copter when it has visible or mechanical damage.
- Always stay out of reach of rotors.
- Ensure that you adhere to all the legal requirements that exist for your copter model in the country in which you are using it.
- If you lose control of the copter, disable the propulsion of the engines immediately by pushing the throttle lever down to turn it off.
Copyright WLtoys.eu | DroneX BV

Steps to install the FPV set on your copter:
1. screw the antenna (1) on the FPV monitor (2)
2. Install the sun block cover (3) on the FPV monitor for better
visibility during sharp sunlight.
3. Mount the FPV monitor (2) on remote (5) by using the FPV
mount bracket (4) and screw set.
4. Turn the monitor on on the right side and then the camera
which is mounted to the copter. Make sure the Antenna of the
camera is extended and connect the camera to the FPV socket
of the copter.
12. Elevator trim
Steering with the phone:
- Toggle button 6 to on. This enables on screen steering like standard remote
Application
2. Make video (saved to camera roll)
3. Go to media library
6. Eneble/disable steering on phone
7. Rotate image
8. Throttle/rudder
9. Elevator/aileron
11. Aileron trim
- Download the app with the QR code which is inside the box
WIFI
1. Take picture (saved to camera roll)
- Connect the battery of the V686
- Start the app and press play
This model comes with a Wifi camera module.
10. Rudder trim
4. Adjust assertiveness (30/60/100%)
- Toggle gyro symbol (button 5) on to steer with mobile device gyroscope. Throttle is always on screen
With the aplication on android and iOS you are able to fly your drone, and fly with FPV (First Person View). Your smartphone can
Connecting the V686K:
- Either steer the quad with the remote or with the phone
5. Steer by gyroscope
- On the mobile device look for the Wifi network starting with LG. Connect
Copyright WLtoys.eu | DroneX BV

Imported by: WLtoys.eu / DroneX BV
Bloemstraat 86HS 1016 LE Amsterdam | www.wltoys.eu |
[e-mail]
Our products comply with the standards and criteria of the
European Union and approved by the EC. For your safety, we
recommend that you read the entire manual before your first
flight.
Congratulations on your purchase of this product from wltoys.eu! Wltoys.eu offers its customers a high quality product. All our
products are carefully tested before shipment. If unfortunately a problem persists, contact your dealer or visit www.wltoys.eu. Your
dealer can also assist you in getting spare parts in case you need them. We hope you will enjoy your experience with our product.
You can contact us at any time on : www.wltoys.eu | [e-mail].
You can find instructional videos and buy spare parts on our website www.wltoys.eu.
For technical support contact your reseller.
WARNING:
Non-compliance with safety rules may cause damage, injury and / or dangerous situations.
This warranty covers manufacturing and material defects in the context of normal use. We take no responsibility for damage
caused indirectly.
Wltoys
Warranty
The use of this product is entirely at your own responsibility and at your own risk. Since we have no control beyond this manual on
when and how you use our product (both flying and maintenance), we are not responsible for any damages or costs incurred by
improper use.
Copyright WLtoys.eu | DroneX BV

The following are excluded from the warranty:
• Damage caused by the failure to comply with security measures or instructions
• Extreme treatment which can not be contained in the usual standards
• Overloading the vehicle or external influences
• Homemade modifications on the product
• The damage caused by the loss of control of the vehicle
• Electric defects due to voltage overload or lightning
• Normal wear and tear of the device and parts
• The costs of transportation, shipping or insurance
• The damage caused by the humidity
• The damage caused by the loss of the product
• After three flights the warranty of brushed engines is void
Copyright WLtoys.eu | DroneX BV