WLtoys V222 User manual

CONTENTS OF THE BOX:
• 1 x Quadcopter drone
• 1 x 2.4GHz remote control with LCD display (6x AA batteries
not included)
• 1 x 3.7V 500mAh Li-po battery
• 1 x Charger
• 1 x 4 Sprare propellers
• 1 x User manual
• 1 x HD camera 720P if included in your model
• 1 x Module if included in your model (V969-V979-V989-V999)
• (1 x card Mirco SD 2GB if module Camera included)
SPECIFICATIONS:
• 2.4GHz Assembled quadcopter drone Ready-to-fly
• 6-axis Gyroscope
• 4 main engines
• 1S Li-po Battery 3.7V 500mAh
• Height: 80mm
• Length: 160 mm (axis to axis)
• Width: 160 mm (axis to axis)
• Weight: 76 grams without battery
• Battery weight: 15.8 grams
• Always follow local laws and regulations! Contact your reseller when in doubt.
• After using the copter ALWAYS disconnect the battery and remove it from the device
• The model and the transmitter must be switched off after use
• Always fly in an open and safe environment where you will not cause any danger to others
• For the remote control, we recommend AA batteries with a voltage of 1.5 to 1.2 volts
• For people without experience, we recommend that you learn to fly with an experienced user during your first flights
• Read the manual carefully and completely
• This model is not suitable for children under 14 years and contains small parts
• Children should only use this model under the supervision of an adult
• Keep hands, face, hair and clothes away from blades.
• Stand out of reach of moving parts of the copter
V222 TRANSMITTER 360 STUNT DRONE
Specifications
Security precautions
• Before each flight, test the distance limit of the transmitter
• Keep these instructions safe
INSTRUCTION MANUAL
Copyright WLtoys.eu | DroneX BV

The user must return used batteries and rechargeable batteries.
It is forbidden to dispose of used batteries in the bins containing
household waste! Batteries / accumulators containing
hazardous substances are marked with the crossed out wheelie
bin. The symbol indicates that the product should be recycled.
The chemical symbols for the respective hazardous substances
are Cd (cadmium), Hg (mercury), Pb (lead). The used batteries
can be disposed for free of charge at collection points in your
community, stores or wherever batteries are sold. You are kindly
requested to conform to your legal obligations and contribute to
the protection of our environment.
DO NOT FLY:
- Around people or animals
- Around large groups of people
- In limited visibility or dark conditions
- Winds above 2 Beaufort
- Near high voltage pylons and / or other types of cabling
- During thunderstorms, rain or high humidity. The device is not water-resistant.
Battery recycling recommendations
For the sensitive and rational conservation, protection and improvement of the quality of the environment, protection of human
health and the preservation of natural resources, the user must send an unusable product to relevant facilities created to this
purpose in accordance with the law.
The crossed out wheelie bin means that the product must be recycled (WARNING: do not throw it in your bin).
Li-po Battery instructions
Copyright WLtoys.eu | DroneX BV

- Keep the batteries out of reach of children
- Non-rechargeable batteries should not be recharged
- Unequally charged batteries or different battery types should
not be used together
- Use recommended batteries or similar
- After using the copter, remove the batteries if you will not use
it again for a long period of time
- The terminals must not be short-circuited
- This model is equipped with a rechargeable Li-po Battery. Li-
po batteries require special attention, follow the manual
- The batteries must be charged with the charger supplied by
WLtoys
- When charging the battery, always ensure that you do so on a
non-combustible surface
- Do not leave charging without supervision
- Always charge the battery to 100%
- Ensure that the battery wires are not in contact to avoid a
short-circuit
- The ignition wires of the battery must not be modified or
damaged
- Never damage the battery mechanically (this could cause an
explosion)
- The battery should not be placed near children (unless you
have an adult supervision)
- The technical design of the battery must not be changed
- Touching of damaged batteries can cause injury. If there is
contact with skin or eyes, seek medical attention immediately!
- Do not charge directly after the flight or when the battery is
warm
1. Charging wire
2. LED
3. Li-po Battery
Plug the charger into a wall socket and connect the battery to
the charger. This can only be done in one way: by firmly
connecting the charging cable. If the green light is on, the
battery is fully charged and can be disconnected. Then do not
forget to unplug the charger from the wall socket.
Green LED = Charged battery
Orange LED = Charging battery
Red LED = Battery is empty / Charging battery
Input : 220V
Charging Current : 500mA
Full Voltage: 4.2 +/- 0.03V
Battery charging
Warning : Always place the battery on a heat resistant surface and never leave it unattended!
Remote Control / Transmitter
Copyright WLtoys.eu | DroneX BV

1. Power LED
2. 4 speeds control
3. Gear lever
4. Throttle trim
5. Rotation trim
6. LCD display
7. Antenna
8. Power switch
9. Mode 1 or 3 / Mode 2 or 4 switch (hardware)
10. 360 degree Roll
11. Directional lever
12. Forwards and backwards trim
13. Crab trim
14. Module 1 : Water jet; bubble jet; video; basket up; lead
single missile
15. Lighting control
16. Module 2 : Taking photos, running missiles, basket down
17. Mode 1 or 3 / Mode 2 or 4 switch (software)
Insert the battery by sliding the cover down. Then insert 4 x AA
batteries as indicated under the cover.
How to fly
- Using the gear lever you can control the rotation axis of the drone. Using the directional lever you can control the flight direction
of the copter.
- Swap the layout of the throttle between the right and the left by switching the lever on as number 9
- To switch mode's from 2 to 4 or 1 to 3 or vice-versa: 1. Turn off remote. 2. Keep model button pressed 3. Turning on the
controller.
- The different calibration buttons help keep the copter stationary. Test this by pressing the accelerator and calibration buttons to
maintain the copter in one place.
- You can choose the percentage of the speed. The higher the value, the faster the reaction will be (e.g. 100% will be more
responsive than 40%). (helicopter L<H).
- The two buttons on the top and the button on the bottom right are used to activate different modules : photos / shots / basket.
Flying is really simple, but you need a little practice at first. Connect to www.wltoys.eu to watch educational films.
Copyright WLtoys.eu | DroneX BV

SIDEWARD
The directional lever serves to move the drone to the left or
the right.
FORWARD
Pushing the directional lever up and down makes your
drone go forward or backward.
ALTITUDE
Pushing the gear lever up and down makes your altitude
rise or fall.
TURN
Pushing the gear lever from side to side, the drone will turn
on its own axis.
Copyright WLtoys.eu | DroneX BV

CAUTION
Procedure to spare engine
The first flight
1. For your first flight make sure to be with a person experienced in flying copters. We advise you to make your first flights on a
relatively soft surface to protect the copter.
2. Find a location away from people, with a smooth surface and without obstacles. Trees, electric lines and water points in the
immediate vicinity should be avoided!
3. Place your copter on the ground about 10 feet away from you. Mind that, when you have a quadcopter, the coloured blades
indicate the front of the copter. It is easiest to position yourself behind the copter for an easier control.
4. Turn the copter on first. Then turn on the remote controll (for some models this will be the other way around) for the V333N,
turn on the copter as well as the controller. then move trottle up and down to connect. after this move throttle to the left low corner
and the directional lever to the right lower corner at the same time, hold these down for a few seconds, this will arm the motors.
5. Start the engine and take off to about 1 meter from the ground. In this way you avoid the phenomenon called "ground effect".
Near the ground the air currents behave differently than at a higher altitude and this will prevent you from losing control of the
copter.
6. Then try to fly gently in one direction. If the engine flies away in the wrong direction, make a controlled landing and try again.
Calibration
Troubleshooting
- Ensure that the copter in flight is always within sight and under control.
- Always use a fully charged battery.
- When finished flying, always turn off the copter first, then the remote control.
- Do not use the copter when it has visible or mechanical damage.
- Always fly in an open and Jellyfished environment to avoid dangerous situations.
- Always stay out of reach of rotors.
- Remember to disconnect the battery of the copter after each flight.
- Ensure that you adhere to all the legal requirements that exist for your copter model in the country in which you are using it.
- If you lose control of the copter, disable the propulsion of the engines immediately by pushing the throttle lever down to turn it off.
Engines are brushed and eventually wear out. When worn out they need to be replaced. For more informations go to
www.wltoys.eu.
Never go full speed for the first 3 flights. After 3 flights, blow out engines with air when possible.
Spare engines can be bought on www.wltoys.eu or with your reseller.
If the copter is unstable, resulting in frenetic flying in all directions, and rotates around its axis so that you have to constantly
correct its flight, then the gyroscope is probably not calibrated properly. To perform recalibration, connect the drone to the
transmitter (part Activation in the manual), then click on 100% button of the remote and move both sticks to the bottom left. When
the calibration is performed, you will either hear a long beep or see flashing lights (on the PCB) or both.
Note: The calibration is done in the factory, it is usually not necessary to do it when you receive the product.
Copyright WLtoys.eu | DroneX BV

Ref | Description | Quant
105 | Bearing | 8
106 | JST plug | 1
107 | LED light red | 2
108 | Motor counterclock | 2
109 | LED light white | 2
112 | Main frame | 4
113 | Motor clockwise | 2
115 | Landing skid | 1
117 | Main body | 1
118 | Carbon fiber arm | 4
121 | Li-po battery | 1
123 | Gear | 4
124 | Cable | 4
125 | Main shaft | 4
126 | Canopy | 1
363 | PCB | 1
364 | Blade | 4
365 | Light | 2
366 | Colour light | 2
1. The receiver LED blinks continuously for more than 4 seconds after the quadcopter battery have been inserted. No response to
the command input. The transmitter is not connected to the device. Repeat the power-on initialization process.
2. No response from the quadcopter after the battery have been connected. There is probably contact failure on the battery
terminals. Turn on the transmitter and ensure that the battery of the vehicle is correctly inserted. Replace the battery and ensure
good contact at the battery's connections. Use fully charged batteries in the remote.
3. The motor does not respond to the throttle stick and the receiver flashes. The quadcopter's battery is exhausted. Charge the
battery or replace it with a charged battery.
4. The main rotor continues to rotate after landing. Confirm that the gear lever is oriented downward.
5. The main rotor rotates but the device does not take off. The blades may be distorted or the quadcopter battery is exhausted.
Charge or replace with a fully charged battery and / or replace the blades.
6. The quadcopter suffers of strong vibrations. The blades are distorted. Replace the blades.
7. The tail is not balanced after adjusting the clip or speed is inconsistent in the left / right pirouette. Tail rotors are probably
damaged. Replace the main wing and / or the main engine.
8. The quadcopter was still moving forward after the adjustment of the levers during hover. The gyroscope is not correctly
calibrated. The gear lever is placed too high or too low. The boot refines the calibration therefore restart on a flat surface.
9. You can not fly, the helicopter falls. The motor is probably fall out or the gears are loose. Reinstall the motor and tighten the
gears.
Spare parts
The copter is not sensitive to crashes, but in case of extreme drops it is possible that some parts may break. All parts can be
ordered and easily assembled. Please contact your dealer or visit www.wltoys.eu for more information.
Additional modules (accessories)
Copyright WLtoys.eu | DroneX BV

This model can be equipped with different modules. This is
available from your retailer or on www.wltoys.eu.
A module may be included in some models.
1. Camera
2. Bubble
3. Fountain
4. Bullet
5. Rescue
The modules are installed as follows:
1. Remove the module from its packaging and place the V-
shaped feet in stirrups at the bottom of the fuselage of the
drone. Make sure the right side is facing forward.
2. Push until a click is heard. If you do not hear a click, rotate
180 degrees and try again.
3. Then connect the plug to the matching slot provided for that
purpose on the support base.
The various modules installation procedure is the same. Keep in
mind that modules must be connected to the base
corresponding to the support base. In the illustration you will find
the exact location of these bases.
1. CAMERA = camera
2-3. SPRAYER = fountain or bubble blower
4. MISSILE = missile shooter
5. HOIST = Rescue module
NB: On www.wltoys.eu you will find the educational films where
everything is explained step-by-step with images and sound.
Imported by: WLtoys.eu / DroneX BV
Bloemstraat 86HS 1016 LE Amsterdam | www.wltoys.eu |
[e-mail]
Our products comply with the standards and criteria of the
European Union and approved by the EC. For your safety, we
recommend that you read the entire manual before your first
flight.
Wltoys
Copyright WLtoys.eu | DroneX BV

• The damage caused by the humidity
• After three flights the warranty of brushed engines is void
• Overloading the vehicle or external influences
• Homemade modifications on the copter
• Electric defects due to voltage overload or lightning
• Normal wear and tear of the device and parts
• The costs of transportation, shipping or insurance
The following are excluded from the warranty:
• Damage caused by the failure to comply with security measures or instructions
• Extreme treatment which can not be contained in the usual standards
• The damage caused by the loss of the copter
• The damage caused by the loss of control of the vehicle
Congratulations on your purchase of this product from wltoys.eu! Wltoys.eu offers its customers a high quality product. All our
products are carefully tested before shipment. If unfortunately a problem persists, contact your dealer or visit www.wltoys.eu. Your
dealer can also assist you in getting replacement parts if the flight has created damage. We hope you will enjoy your experience
with our product.
You can contact us at any time on : www.wltoys.eu | [e-mail].
You can find instructional videos and buy spare parts on our website www.wltoys.eu.
For technical support contact your reseller.
WARNING:
Non-compliance with safety rules may cause damage, injury and / or dangerous situations.
Warranty
The use of the copter is entirely at your own responsibility and at your own risk. Since we have no control beyond this manual
when you use the remote control and the copter (both flying and maintenance), we are not responsible for any damages or costs
incurred by improper use.
This warranty covers manufacturing and material defects in the context of normal use. We take no responsibility for damage
caused indirectly.
Copyright WLtoys.eu | DroneX BV