Wolf CT15I User manual

INSTALLATI N GUIDE
Induction Cooktops

Important Note
To ensure the safe and efficient use of Wolf equipment,
please take note of the following types of highlighted
information throughout this guide:
IMP RTANT N TE highlights information that is especially
important.
CAUTI N signals a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
Contents
Wolf Induction Cooktops . . . . . . . . . . . . . . . . . . . . . . . 3
Induction Cooktop Specifications . . . . . . . . . . . . . . . . 4
Induction Cooktop Installation . . . . . . . . . . . . . . . . . . 12
ServiceInformation...........................15
Features and specifications are subject to change at any time
without notice. Visit wolfappliance.com/specs for the most
up-to-date information.
IMP RTANT N TE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specified.

Wolf Induction Cooktops 3
wolfappliance.com/specs
Induction Cooktop Installation
IMP RTANT N TE: This installation must be completed
by a qualified installer or Wolf authorized service center
technician.
Read this entire installation guide prior to installation and
save for the local inspector’s reference. The homeowner
should keep this installation guide for future reference.
This appliance must be installed in accordance with
National Electrical Codes, as well as all state, municipal
and local codes. The correct voltage, frequency and
amperage must be supplied to the appliance from a dedi-
cated, grounded circuit which is protected by a properly
sized circuit breaker or time delay fuse. The proper
voltage, frequency, and amperage ratings are listed on the
product rating plate.
Record the model and serial numbers before installing the
induction cooktop. Both numbers are listed on the product
rating plate, located on the underside of the cooktop.
Refer to the illustration below.
Wolf Induction Cooktop
Model Number
Serial Number
MEL
TOFF
HI-POWER
HIGH
SIMOFFON
HI-POWER
HIGH
SIMOFFON
MEL
THIGH
OFFON
Location of rating plate.
RATING P ATE

Induction Cooktop Specifications 4
31/2"(89)
11/4"(32) 7/8"(22)
ALL SIDES
TERM BOX
21" (533)
15"
(381)
15" (381) FRAMED
30" (762)
31/2"(89)
11/4"(32) 7/8"(22)
ALL SIDES
TERMINAL BOX
21" (533)
30" (762) FRAMED
36" (914)
31/2"(89)
11/4"(32) 7/8"(22)
ALL SIDES
TERMINAL BOX
21" (533)
36" (914) FRAMED
30" (762)
4" (102)
11/4"(32) 7/8"(22)
ALL SIDES
TERMINAL BOX
21" (533)
30" (762) UNFRAMED
36" (914)
4" (102)
11/4"(32) 7/8"(22)
ALL SIDES
TERMINAL BOX
21" (533)
36" (914) UNFRAMED
Overall Dimensions

Induction Cooktop Specifications 5
wolfappliance.com/specs
Installation Requirements
IMP RTANT N TE: Installation of the induction cooktop
must meet location requirements shown in the installation
illustration for your specific model on the following pages.
All dimensions listed are minimum requirements for safe
operation.
Wolf induction cooktops are intended for indoor use. For
ease of installation, Wolf recommends using 33" (838)
wide cabinets with 30" (762) cooktops and 39" (991)
cabinets with 36" (914) cooktops. They are designed to fit
a standard 24" (610) deep base cabinet with a 25" (635)
deep countertop. Before making the countertop cut-out,
verify that the cooktop will clear the side walls of the base
cabinet.
A minimum height clearance of 61/4" (159) is required from
the top of the countertop to any combustible surface
directly below the cooktop. If a shelf is installed below the
unit, a 1" (25) gap at the rear of the cabinet shelf is neces-
sary to allow for proper ventilation.
Clearance is required for the terminal block located at the
right rear of the cooktop. Refer to the illustration below for
dimensions.
Failure to locate the cooktop without proper clearances
will result in a fire hazard.
35/16"
(84)
23/16"
(56)
15/16"
(24)
7/8"
(22)
11/4"(32)
Terminal block dimensions.
Unframed induction cooktops can be mounted flush with
the top of the countertop or as a frameless installation
with the glass-ceramic top mounted on top of the counter-
top surface. In either installation the countertop cut-out
dimensions are the same. If the cooktop is to be mounted
flush with the countertop, a recessed area surrounding the
countertop cut-out must be provided.
IMP RTANT N TE: Flush mount installations are intended
for granite, solid surface or stone countertop surfaces only.
It is recommended that you use a Wolf cooktop ventilation
hood, pro hood or hood liner with the induction cooktop.
Framed induction cooktops can accommodate a Wolf
downdraft ventilation system. Refer to the Wolf design
guide.

Induction Cooktop Specifications 6
Electrical Requirements
Wolf induction cooktops have a 4' (1.2 m) flexible conduit
and require a separate, grounded 3-wire electrical supply
with its own circuit breaker. ocate the electrical supply
within the shaded area shown in the installation illustration
for your specific model on the following pages.
M DEL CT15I/S
•Power supply: 240/208 V AC, 60 Hz, 20 amp service.
•Max connected load: 3.6 kW at 240 V, 3.1 kW at 208 V.
M DELS CT30I/S AND CT30IU
•Power supply: 240/208 V AC, 60 Hz, 40 amp service.
•Max connected load: 7.2 kW at 240 V, 6.3 kW at 208 V.
M DELS CT36I/S AND CT36IU
•Power supply: 240/208 V AC, 60 Hz, 50 amp service.
•Max connected load: 10.2 kW at 240 V, 8.9 kW at 208 V.
IMP RTANT N TE: You must follow all National Electrical
Code regulations. In addition, be aware of local codes and
ordinances when installing your service.
IMP RTANT N TE: Performance may be compromised if
the electrical supply is less than 240 volts.
The cooktop is provided with a terminal box and conduit
consisting of two insulated hot lead conductors and one
insulated ground conductor. Refer to the illustration below.
IMP RTANT N TE: For electrical installation, attach the
conductors to the residence wiring in accordance with
National Electrical Codes and all state, provincial, munici-
pal and local codes.
This appliance must be installed in accordance with
National Electrical Codes, as well as all state, municipal
and local codes. The correct voltage, frequency and
amperage must be supplied to the appliance from a dedi-
cated, grounded circuit which is protected by a properly
sized circuit breaker or time delay fuse. The proper
voltage, frequency and power ratings are listed on the
product rating plate, located on the underside of the
cooktop. Refer to the illustration on page 3 for location of
the rating plate.
The complete appliance must be properly grounded at
all times when electrical power is applied.
Do not ground the appliance with the neutral (white)
house supply wire. A separate ground wire must be
utilized.
If aluminum house supply wiring is utilized, splice the
appliance copper wire to the aluminum house wiring
using special connectors design and agency certified
for joining copper and aluminum. Follow the connector
manufacturer's recommended procedure carefully.
Improper connection can result in a fire hazard.
GROUND
L2
L1
Wiring diagram.

Induction Cooktop Specifications 7
wolfappliance.com/specs
36" (914)
FLOOR TO
COUNTERTOP
30" (762) min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
SEE COUNTERTOP
CUT-OUT BELOW
133/8"(340)
CUT-OUT
WIDTH
COUNTERTOP CUT-OUT
FRONT
191/4"(489)
CUT-OUT
DEPTH
21/2"(64) min
2" (51) TO
COMBUSTIBLE*
2" (51) TO
COMBUSTIBLE*
SIDE
CABINET
13" (330)
max
*Minimum clearance from cooktop cut-out to combustible materials up to 18" (457) above countertop.
NOTE: Application shown allows for installation of two 15" (381) modules side by side.
E
15" (381)
15"
(381)
41/2"(114)
18" (457) min
2" (51) min*
15" (381) Framed Induction Cooktop
STANDARD INSTALLATI N

Induction Cooktop Specifications 8
18" (457) min
36" (914)
FLOOR TO
COUNTERTOP
30" (762) min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
30-INCH OVEN
OPENING
41/2"(114)
10" (254)
31/2"(89) E
SEE COUNTERTOP
CUT-OUT BELOW
33/4"(95)min
2" (51) TO
COMBUSTIBLE*
2" (51) TO
COMBUSTIBLE*
SIDE
CABINET
13" (330)
max
283/8"(721)
CUT-OUT WIDTH
COUNTERTOP CUT-OUT
FRONT
191/4"(489)
CUT-OUT
DEPTH
21/2"(64) min
*Minimum clearance from cooktop cut-out to combustible materials up to 18" (457) above countertop.
NOTE: Electrical location applies only to installation with built-in oven.
2" (51) min*
30" (762) Framed Induction Cooktop
STANDARD INSTALLATI N

Induction Cooktop Specifications 9
wolfappliance.com/specs
18" (457) min
36" (914)
FLOOR TO
COUNTERTOP
30" (762) min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
36-INCH OVEN
OPENING
41/2"(114)
10" (254)
31/2"(89) E
SEE COUNTERTOP
CUT-OUT BELOW
343/8"(873)
CUT-OUT WIDTH
COUNTERTOP CUT-OUT
FRONT
191/4"(489)
CUT-OUT
DEPTH
21/2"(64) min
33/4"(95)min
2" (51) TO
COMBUSTIBLE*
2" (51) TO
COMBUSTIBLE*
SIDE
CABINET
13" (330)
max
*Minimum clearance from cooktop cut-out to combustible materials up to 18" (457) above countertop.
NOTE: Electrical location applies only to installation with built-in oven.
2" (51) min*
36" (914) Framed Induction Cooktop
STANDARD INSTALLATI N

Induction Cooktop Specifications 10
18" (457) min
36" (914)
FLOOR TO
COUNTERTOP
30" (762) min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
30-INCH OVEN
OPENING
41/2"(114)
10" (254)
31/2"(89) E
SEE COUNTERTOP
CUT-OUT BELOW
283/8"(721)
CUT-OUT WIDTH
COUNTERTOP CUT-OUTRECESS FOR FLUSH INSTALLATION
FRONT
193/8"(492)
CUT-OUT
DEPTH
27/16"(62) min
211/8"(537)
RECESS
FOR FLUSH
INSTALLATION
19/16"(40)
4" (102)min
2" (51) TO
COMBUSTIBLE*
2" (51) TO
COMBUSTIBLE*
SIDE
CABINET
13" (330)
max
*Minimum clearance from cooktop cut-out to combustible materials up to 18" (457) above countertop.
NOTE: Electrical location applies only to installation with built-in oven.
5/16"(8)
7/8"
(22) max
COUNTERTOP
PROFILE
15/16"(33)
RADIUS
7/16"(11) RADIUS
301/8"(765)
RECESS FOR FLUSH INSTALLATION
2" (51) min*
30" (762) Unframed Induction Cooktop
FLUSH M UNT INSTALLATI N

Induction Cooktop Specifications 11
wolfappliance.com/specs
18" (457) min
36" (914)
FLOOR TO
COUNTERTOP
30" (762) min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
36-INCH OVEN
OPENING
41/2"(114)
10" (254)
31/2"(89) E
SEE COUNTERTOP
CUT-OUT BELOW
343/8"(873)
CUT-OUT WIDTH
COUNTERTOP CUT-OUTRECESS FOR FLUSH INSTALLATION
FRONT
193/8"(492)
CUT-OUT
DEPTH
27/16"(62) min
211/8"(537)
RECESS
FOR FLUSH
INSTALLATION
19/16"(40)
4" (102)min
2" (51) TO
COMBUSTIBLE*
2" (51) TO
COMBUSTIBLE*
SIDE
CABINET
13" (330)
max
*Minimum clearance from cooktop cut-out to combustible materials up to 18" (457) above countertop.
NOTE: Electrical location applies only to installation with built-in oven.
5/16"(8)
7/8"
(22) max
COUNTERTOP
PROFILE
15/16"(33)
RADIUS
7/16"(11) RADIUS
361/8"(918)
RECESS FOR FLUSH INSTALLATION
2" (51) min*
36" (914) Unframed Induction Cooktop
FLUSH M UNT INSTALLATI N

Induction Cooktop Installation 12
Multiple Cooktop Installation
IMP RTANT N TE: Unframed induction cooktops are not
designed to be installed in combination with other
cooktops.
If the framed induction cooktop is to be used with any
combination of additional cooktops or modules with a filler
strip, the dimensions provided in the chart below are
derived by adding 11/4" (32) additional space for each
additional unit, to give you the total countertop cut-out
width. Dimensions include the filler strip.
IMP RTANT N TE: For model CT15I/S, the cut-out width
should be increased from 133/8" (340) to 14" (356) when
installed with multiple cooktops.
When multiple cooktops are installed side by side, each
unit must have its own separate recommended electrical
circuit.
When two or more modules are installed together, an
integrated module filler strip is recommended. If a 30"
(762) downdraft ventilation system is also installed, an
integrated module support for downdraft ventilation is also
required.
The filler strip and other accessories are available through
your authorized Wolf dealer. To obtain local dealer informa-
tion, visit the find a showroom section of our website,
wolfappliance.com.
Multiple Cooktops
C UNTERT P CUT- UT WIDTH
2 Modules 291/4"(743)
3 Modules 441/2"(1130)
4 Modules 593/4"(1518)
30" (762) Cooktop / Module 441/4"(1124)
30" (762) Cooktop / 2 Modules 591/2"(1511)
36" (914) Cooktop / Module 501/4"(1276)
Unframed Installations
Unframed induction cooktops can be mounted flush with
the top of the countertop or as a frameless installation
with the glass-ceramic top mounted on top of the counter-
top surface. In either installation the countertop cut-out
dimensions are the same. If the cooktop is to be mounted
flush with the countertop, a recessed area surrounding the
countertop cut-out must be provided. Refer to the installa-
tion illustrations on pages 10–11.
IMP RTANT N TE: An installation kit and additional
instructions required for a flush mount installation are
provided with the unframed induction cooktop.
Flush mount installations are intended for granite, solid
surface or stone countertop surfaces only. Contact
with hot cookware may cause damage to countertop
surfaces that are not resistant to high heat.

FLUSH M UNT INSTALLATI N— PTI N 2
For this flush mount installation, the countertop cut-out
will be the same size as the outer edge of the glass-
ceramic top. It is recommended that unframed cooktop
itself be used as the template for the cut-out. Turn the
cooktop over and mark the opening using the glass-
ceramic top as a template.
It will be necessary to attach -shaped cleats to the inner
perimeter of the countertop cut-out to support the
unframed cooktop. The top edge of the cleat can be no
wider than 7/8" (22) and will be attached 5/16" (8) below the
surface of the countertop. Refer to the illustration below.
Attach the cleats wherever enough countertop material is
present.
For additional support in the cut-out area, adhere scrap
countertop material to the bottom side of the countertop.
Consult your countertop supplier for the proper methods
of attachment.
Induction Cooktop Installation 13
wolfappliance.com/specs
Unframed Installations
FLUSH M UNT INSTALLATI N— PTI N 1
For this flush mount installation, a recessed area
surrounding the standard countertop cut-out is required.
Fabrication of the recessed area must take place before
the final countertop installation. A template of the counter-
top cut-out is provided with the unframed cooktop for
fabrication purposes.
IMP RTANT N TE: This option is not recommended for
molded backsplash style countertops.
In order to rout the required recessed area for this flush
mount installation, a second template must be made from
1/2" (13) plywood. The template will be used as a guide for
a top-bearing router bit.
Make the wood template wide enough so that clamps
used to hold the template to the countertop do not inter-
fere with the router base. The cut-out dimension of the
wood template should match the outer perimeter of the
template supplied with the cooktop.
Center the wood template over the existing cut-out in the
countertop and clamp. Use double-sided tape to adhere
the template to the countertop to keep the template from
shifting during routing. Make sure that the adhesive can
be easily removed by testing it on a scrap piece of the
countertop. Using a top-bearing router bit with the wood
template as a guide, rout out a 5/16" (8) deep recessed
area in the countertop cut-out.
7/8"(22)
5/16"(8)
L-SHAPED
CLEATS
Support cleats.

Verify Cooktop Operation
Before operating the induction cooktop, be sure to read
the entire use & care guide included with the cooktop for
important safety, operating and warranty information.
Clean the glass-ceramic surface as recommended in the
induction cooktops use & care guide. The cooktop surface
must be free of any foreign substances, especially those
that could melt and permanently adhere to the glass-
ceramic.
Turn on the electrical supply to the cooktop. Check opera-
tion of the controls and verify that each of the induction
elements is coming up to temperature.
IMP RTANT N TE: A small amount of smoke and odor
may be noticed during the initial break-in period.
Induction Cooktop Installation 14
Install the Cooktop
Attach the foam strip to the underside of the cooktop
frame. Refer to the illustration below. For unframed
cooktops, be sure to adhere the foam strip to the outer
edge of the glass-ceramic top, not the support frame.
Gently lower the unit into the cut-out area in the counter-
top and center. Check that the front edge of cooktop is
parallel to the front edge of the countertop. Check that all
required clearances are met.
Attach the brackets to the bottom of the cooktop, as
shown in the illustration below. Install clamping screws
into the brackets and tighten until the screws contact the
underside of the countertop. Do not overtighten screws.
IMP RTANT N TE: Do not seal the cooktop to the coun-
tertop. It must be removed if service is necessary.
FOAM
STRIP
COOKTOP FRAME
Foam strip. Installation brackets.
COUNTERTOP
BRACKET
SCREWS
BRACKET
4" (102)
CLAMPING
SCREW
Do not operate the cooktop if the glass-ceramic surface
is broken. Call a Wolf authorized service center.
Cooktop Removal
IMP RTANT N TE: Cooktop removal should only be done
by a Wolf authorized service center technician.
If it is necessary to remove the cooktop for cleaning or
service, disconnect the electrical supply. Remove the
mounting brackets and remove the cooktop. Reinstall in
the reverse order.
For flush mount installations, use a razor blade to carefully
cut around the perimeter seal. A new RTV installation kit
will be required to reinstall the cooktop. This kit and other
accessories are available through your authorized Wolf
dealer. To obtain local dealer information, visit the find a
showroom section of our website, wolfappliance.com.

Service Information 15
Troubleshooting
IMP RTANT N TE: If the induction cooktop does not
operate properly, follow these troubleshooting steps:
•Verify that electrical power is being supplied to the
cooktop.
•Check the electrical connections to ensure that the
installation has been completed correctly.
•Refer to the troubleshooting guide in the induction
cooktops use & care guide.
•If the cooktop still does not operate properly, contact a
Wolf authorized service center. Do not attempt to repair
the cooktop yourself. Wolf is not responsible for
service required to correct a faulty installation.
Service Information
If service is necessary, maintain the quality built into your
induction cooktop by calling a Wolf authorized service
center.
To obtain the name and number of a Wolf authorized
service center, check the contact & support section of our
website, wolfappliance.com or call Wolf customer service
at 800-222-7820.
When calling for service, you will need the model and
serial numbers of the induction cooktop. Both numbers
are listed on the product rating plate, located on the
underside of the cooktop. Refer to the illustration below.
wolfappliance.com/specs
The information and images in this guide are the copyright property of Wolf Appliance, Inc. Neither this guide nor any information or images contained herein
may be copied or used in whole or in part without the express written permission of Wolf Appliance, Inc. ©Wolf Appliance, Inc. all rights reserved.
Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc.
Sub-Zero, Sub-Zero & Design, Dual Refrigeration, Constant Care and The iving Kitchen are registered trademarks and service marks of Sub-Zero, Inc.
(collectively, the “Company Marks.”) All other trademarks or registered trademarks are property of their respective owners in the United States and other countries.
MEL
TOFF
HI-POWER
HIGH
SIMOFFON
HI-POWER
HIGH
SIMOFFON
MEL
THIGH
OFFON
Location of rating plate.
RATING P ATE

W LF APPLIANCE, INC. P. . B X 44848 MADIS N, WI 53744 W LFAPPLIANCE.C M 800.222.7820
812138 REV-B 8/2010