Wolf Pro Island Instruction Manual

INSTALLATI N GUIDE
Pro sland Ventilation Hoods
READ AND SAVE THESE INSTRUCTI NS

mportant Note
To ensure the safe and efficient use of Wolf equipment,
please take note of the following types of highlighted
information throughout this guide:
IMP RTANT N TE highlights information that is especially
important.
CAUTI N signals a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
Contents
Wolf Pro Island Ventilation Hoods. . . . . . . . . . . . . . . . . 3
SafetyInstructions ............................4
Installation Considerations . . . . . . . . . . . . . . . . . . . . . . 5
Pro Island Hood Specifications . . . . . . . . . . . . . . . . . . 6
Pro Island Hood Installation . . . . . . . . . . . . . . . . . . . . . 8
ServiceInformation...........................18
Features and specifications are subject to change at any time
without notice. Visit wolfappliance.com/specs for the most
up-to-date information.
IMP RTANT N TE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specified.

Wolf Pro sland Ventilation Hoods 3
wolfappliance.com/specs
Pro sland Hood nstallation
IMP RTANT N TE: This installation must be completed
by a qualified installer or Wolf authorized service center
technician.
Read this entire installation guide prior to installation and
save for the local inspector’s reference. The homeowner
should keep this installation guide for future reference.
This appliance must be installed in accordance with
National Electrical Codes, as well as all state, municipal
and local codes. The correct voltage, frequency and
amperage must be supplied to the appliance from a dedi-
cated, grounded circuit which is protected by a properly
sized circuit breaker or time delay fuse. The proper
voltage, frequency, and amperage ratings are listed on the
product rating plate.
Record the model and serial numbers before installing the
ventilation hood. Both numbers are listed on the product
rating plate, located inside the left wall of the hood shell.
Refer to the illustration below.
Wolf Pro Island Hood
Model Number
Serial Number
Location of rating plate
(inside hood).
RAT NG PLATE

MPORTANT NSTRUCT ONS
T REDUCE THE RISK F FIRE, ELECTRIC
SH CK R INJURY, BSERVE THE F LL WING:
• nstallation work and electrical wiring must be
done by qualified person(s) in accordance with all
applicable codes and standards, including fire-rated
construction.
• Two installers are recommended due to the size and
weight of the pro ventilation hood.
• nstall the pro ventilation hood only with a blower
manufactured by Wolf.
• When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
• Ducted fans must always be vented to the outdoors.
Safety nstructions 4
To reduce the risk of fire and properly exhaust air,
be certain to duct air outside. Do not vent exhaust
air into spaces within walls or ceilings or into attics,
crawl spaces or garages.
T REDUCE THE RISK F INJURY T PERS NS IN
THE EVENT F A RANGE T P GREASE FIRE,
BSERVE THE F LL WING:
• Smother flames with close-fitting lid, cookie sheet,
or metal tray, then turn off the burner. Be careful to
prevent burns. f the flames do not go out immedi-
ately, evacuate and call the fire department.
• Never pick up a flaming pan—you may be burned.
• Do not use water, including wet dishcloths or towels
—a violent steam explosion will result.
USE AN EXTINGUISHER NLY IF:
• You know you have a class ABC extinguisher and
you already know how to operate it.
• The fire is small and contained in the area where it
started.
• The fire department is being called.
• You can fight the fire with your back to an exit
(NFPA fire safety tips).
T REDUCE RISK F RANGE T P GREASE FIRE:
A) Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on
low or medium settings.
B) Always turn the ventilation hood on when
cooking at high heat or when flambeing foods
such as crepes suzette or cherries jubilee.
C) Clean ventilation fans frequently. Grease should
not be allowed to accumulate on fan or filter.
D) Use proper pan size. Always use cookware
appropriate for the size of the surface burner.
The hood motor has a thermal overload which will
automatically shut off the motor if it becomes over-
heated. The motor will restart when it has cooled
down. If the motor continues to shut off and restart,
have the hood serviced.

nstallation Considerations 5
wolfappliance.com/specs
nstallation Considerations
Wolf pro ventilation hoods are recommended for use with
all Wolf cooking appliances. sland hoods should be larger
than the cooking surface by 3" (76) on each side. The
ventilation hood should be installed 30" (762) to 36" (914)
above the countertop.
•Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the Wolf warranty. Refer to the Wolf pro
ventilation hoods use & care guide for warranty details,
or visit the contact & support section of our website,
wolfappliance.com.
•Make sure you have the tools and materials necessary
for proper installation.
•Warranty service must be performed by a Wolf author-
ized service center. Wolf is not responsible for service
required to correct a faulty installation.
MATERIALS INCLUDED WITH H D:
•Transition with backdraft damper—attached inside
hood (needs to be removed)
•Two control knobs
•Filters and grease cups (installed in hood)
•nstallation package and hardware
•nstallation guide, use & care guide and product
registration card
•Wolf logo nameplate
When performing installation, servicing or cleaning the
ventilation hood, it is recommended that safety glasses
and gloves be worn.
BL WER ASSEMBLIES
Wolf pro ventilation hoods are shipped without the blower
assembly. nternal, in-line and remote blowers are avail-
able through your authorized Wolf dealer. For local dealer
information, visit the find a showroom section of our
website, wolfappliance.com.
The blower will vary in size and is dictated by the cooking
surface, the volume of air that needs to be moved and the
length of the duct run. Refer to ventilation recommenda-
tions in the Wolf design guide.
IMP RTANT N TE: Use only a Wolf blower with the pro
ventilation hood.
DUCT C VER
Optional stainless steel duct covers are available in a
variety of heights for all pro ventilation hoods through
your authorized Wolf dealer. For local dealer information,
visit the find a showroom section of our website,
wolfappliance.com.
IMP RTANT N TE: nstalling a duct cover will impact all
aspects of the hood installation including hood location,
ducting, electrical placement and the mounting surface.

Pro sland Hood Specifications 6
Overall Dimensions
18" (457)
OVERALL
HEIGHT
4"(102)
34" (864)
OVERALL DEPTH
13"
(330)
WIDTH MINUS 18" (457)
36" (914), 42" (1067), 54" (1372)
AND 66" (1676) WIDTHS
PR ISLAND H DS
nstallation Specifications
PR ISLAND H DS
LOCATION OF ELECTRICAL
THROUGH TOP OF HOOD
WIDTH OF HOOD
30" (762) TO
36" (914)
TO COUNTERTOP
18" (457)
HEIGHT
OF HOOD
34" (864)
DEPTH OF HOOD

Pro sland Hood Specifications 7
wolfappliance.com/specs
nstallation Specifications
The illustration below provides dimensions critical for
proper installation of the pro island hood. Dimensions A
and B in the illustration will vary with the width of the
hood. Refer to the chart below.
Pro Island Hoods
WIDTH F H D AB
36" (914) 18" (457) 9" (228)
42" (1067) 24" (610) 12" (304)
54" (1371)* 36" (914) 18" (457)
66" (1676)* 48" (1219) 24" (610)
A
WIDTH OF
TOP PLATE
61/2"
(165)
10" (254)
B
TO CENTER
OF TRANSITION
7"
(178)
13"
(330)
Pro island hoods.
Electrical Requirements
Wolf pro ventilation hoods require a separate, grounded
120 V AC, 60 Hz power supply. The service should have its
own 15 amp circuit breaker. Locate the electrical supply in
the ceiling through the top of the island hood. Refer to the
installation specifications illustration on the previous page.
IMP RTANT N TE: You must follow all National Electrical
Code regulations. n addition, be aware of local codes and
ordinances when installing your service.
Risk of electrical shock. This ventilation hood must be
properly grounded. Electrical service for the hood must
be installed by a qualified electrician in accordance
with all applicable national and local electrical codes.

Pro sland Hood nstallation 8
nstall Ductwork
IMP RTANT N TE: Pro ventilation hoods must exhaust to
the outdoors.
Wolf recommends that the pro island hood be installed
30" (762) to 36" (914) above the countertop. Consult a
qualified HVAC engineer for specific ducting applications.
A 10" (254) round duct is recommended for pro ventilation
hoods. Use only rigid metal ductwork, do not use flex
ducting.
Decide where the ductwork will run between the island
hood and the outside. Pro island hoods have a vertical
discharge. A straight, short duct run will allow the ventila-
tion hood to perform most efficiently. Limit the number of
elbows and transitions. The duct run should be no longer
than 50' (15 m). There is a possibility of noise issues, if a
remote blower is used with a short duct run.
Unless you are using a remote blower, a roof or wall cap
must be installed. Connect 10" (254) round metal
ductwork to the cap and work back towards the hood.
Use duct sealing tape to seal joints between ductwork
sections.
Pro island hoods have a backdraft damper included in the
transition assembly. Local codes may require the use of an
additional backdraft damper. Contact your local HVAC
professional for specific requirements. n cold weather
installations, a backdraft damper is necessary to minimize
the backflow of cold air into the room.
Local building codes may require the use of make-up air.
Consult your local HVAC professional for specific require-
ments in your area.
PR ISLAND H DS
To reduce the risk of fire, use only metal ductwork.
30" (762) TO 36" (914)
BOTTOM OF
HOOD TO
COUNTERTOP
18" (457)
HOOD HEIGHT
DUCTWORK INSTALLATION
THROUGH ROOF
34" (864)
HOOD DEPTH
4" (102)
13"
(330)

Pro sland Hood nstallation 9
wolfappliance.com/specs
Ceiling Framing
IMP RTANT N TE: Aminimum 10" (254) opening in the
ceiling is required to accommodate the ductwork neces-
sary for proper ventilation.
1) Layout dimensions of the top plate of the hood (or top
of duct cover) on the ceiling. The top plate dimensions
will vary with the width of the island hood. Refer to the
illustration and chart on page 7.
2) Construct the ceiling framing using minimum 2" x 4"
lumber. Proper structural support is required to accom-
modate the weight of the hood.
3) Mark the center location of the hood. nstall 2" x 4"
blocking between ceiling joists. Refer to the illustration
below.
4) Drill four 5/32" diameter holes in the framing to match
mounting holes in the top plate of the hood (or top of
duct cover).
WIDTH OF TOP PLATE
2" X4"
BLOCKING
MOUNTING
HOLES
13" (330)
DEPTH OF
TOP PLATE
Ceiling framing.
Framing must be fastened together and to ceiling joists
to provide enough structural strength to support the
weight of the hood and internal blower, if applicable.

Pro sland Hood nstallation 10
DUCT C VER INSTALLATI N
1) Use the four 1/4" x 3" (76) lag screws and washers
(provided with hood) to attach the duct cover to ceiling
framing. The width of the duct cover should be the
same as the top plate of the island hood. Refer to the
illustration and chart on page 7.
2) nstall additional #10 x 2" (51) hex head screws
(provided with hood) along the top edge of the duct
cover for support. Refer to the illustration below.
3) Proceed with hood preparation and installation.
DUCT
COVER
LAG
SCREWS
HEX HEAD
SCREWS
Duct cover installation.
Duct Cover
IMP RTANT N TE: f an optional duct cover is to be used
with the pro island hood, it must be attached before
installing the hood.
Installing a duct cover will impact all aspects of the
hood installation, including hood location, ducting,
electrical placement and the mounting surface.

Pro sland Hood nstallation 11
wolfappliance.com/specs
4)The hood assembly is shipped with the transition
attached. The transition is shipped upside down in the
top of the hood and must be removed and reinstalled
in the proper position. Separate the transition from the
hood assembly by removing the four shipping screws.
nvert and reattach the transition to the hood with the
shipping screws.
5) f you are installing an in-line or remote blower, punch
out the knockout hole located on the top of the hood.
nstall a wire clamp (provided with hood) for the remote
blower cable. nstall another wire clamp in the hole on
top of the hood for the Romex®wire. Refer to the in-
line and remote blowers section on page 16 and follow
installation instructions provided with the blower.
Hood Preparation
1)Remove the filters of the pro island hood by pushing
each filter up at the angle it is placed in, and rotate the
bottom of the filter down. Refer to the illustration
below. Gloves should be worn when handling filters.
2) Slide the grease cups out from the bottom edges of the
front and back of the hood.
3) Using a Phillips screwdriver, remove the screws retain-
ing the hood’s internal frame shown in the shaded area
of the illustration below. Be sure to leave the other two
screws in place. Do not discard the screws. They will
be used to reinstall the internal frame after installation
is complete. Remove the internal frame from the hood
and set aside.
FILTER
Remove filters. Internal frame.
REMOVE
SCREWS
DO NOT
REMOVE
DO NOT
REMOVE

Hood nstallation
IMP RTANT N TE: f an optional duct cover is to be used,
it must be installed before installing the island hood. Refer
to duct cover installation on page 10.
The filters and internal frame must be removed from the
hood prior to installation. Refer to hood preparation on the
previous page.
INSTALLATI N WITH DUCT C VER
1) f a duct cover has been installed, install the four 5/16"
bolts (provided with duct cover) through the mounting
holes on each corner of the hood and into the bottom
edge of the duct cover. Attach the duct cover to the
hood assembly with the #12 x 7/8" (22) self-tapping hex
head screws (provided with duct cover). Refer to the
illustration below.
2) Connect the 10" (254) round ductwork to the transition
using sheet metal screws and duct sealing tape.
3) f you are installing an internal blower, do not reinstall
the internal frame and filters until blower installation
is complete. Refer to internal blower information on
page 15.
4) Proceed with hood wiring connections.
Due to the weight of the hood, be sure to have
adequate assistance for installation.
Pro sland Hood nstallation 12
5/16"
BOLT
DUCT
COVER
NUT
HEX HEAD
SCREW
Installation with duct cover.
INSTALLATI N WITH UT DUCT C VER
1) Lift the hood and align the hood mounting holes with
the predrilled holes in the ceiling framing. nstall the
four 1/4" x 3" (76) lag screws with the washers
(provided with hood) through the mounting holes on
each corner of the island hood and into framing. Do
not overtighten screws.
2) Connect the 10" (254) round ductwork to the transition
using sheet metal screws and duct sealing tape.
3) Adjust the positioning of the hood if necessary, and
tighten the four lag screws until the hood is flush with
the ceiling. nstall additional #10 x 2" (51) hex head
screws (provided with hood) through the remaining
mounting holes in the top plate of the hood for
additional support. Refer to the illustration below.
4) f you are installing an internal blower, do not reinstall
the internal frame and filters until blower installation
is complete. Refer to internal blower information on
page 15.
5) Proceed with hood wiring connections.
HEX HEAD
SCREW LAG
SCREW
Installation without duct cover.

Pro sland Hood nstallation 13
wolfappliance.com/specs
nternal Blower
WIRING F R INTERNAL BL WER
1) Remove the hood electrical box cover. Run Romex®
wire from a 120 V AC, 15 amp circuit to the hood
installation location. nsert the Romex®wire into the
electrical box by running it through the wire clamp
previously installed. Tighten the wire clamp to secure
the wire. Refer to the illustration and chart below for
the location of wiring for your specific hood. Do not
remove the wire connector on the orange wire in the
hood electrical box.
2) Using the wire connectors provided, connect black
wire to power supply black wire, white wire to power
supply white wire and green or bare wire from power
supply to green ground screw in the electrical box.
3) Place all wiring connections inside the electrical box
and reinstall the cover. Make sure all wires are secure
and that no wires are pinched between the cover and
electrical box.
A
11/2"
(38)
2"
(51)
Location of hood wiring.
Location of Hood Wiring
WIDTH F H D A
36" (914) 2" (51)
42" (1067) 3" (76)
54" (1371) 4" (102)
66" (1676) 4" (102)
Blower Assemblies
Pro ventilation hoods are shipped without the blower
assembly. nternal, in-line and remote blowers are avail-
able through your authorized Wolf dealer. For local dealer
information, visit the find a showroom section of our
website, wolfappliance.com.
The blower will vary in size and is dictated by the cooking
surface, the volume of air that needs to be moved and the
length of the duct run. Refer to ventilation recommenda-
tions in the Wolf design guide.
IMP RTANT N TE: Use wire connectors or wire nuts
approved by UL or C/UL.
Before making electrical connections, make sure the
electrical power is turned off at the service panel.
To reduce the risk of fire and electric shock, install
this ventilation hood only with a blower manufactured
by Wolf.

Pro sland Hood nstallation 14
nternal Blower
IMP RTANT N TE: Refer to specific installation instruc-
tions provided with each blower assembly for additional
mounting and wiring instructions.
BL WER INSTALLATI N
1) Discard the hex nuts provided with the blower.
2) Lift the blower assembly into position inside the hood.
3) Engage the two tabs on the blower into the two slots in
the top plate of the island hood. Secure the blower to
the threaded studs with two hex nuts (provided with
blower). Refer to the illustration.
5) Plug the blower power cords into receptacles located
near the center of the hood shell. Use the clips on the
interior of the hood to secure excess power cord.
6) Once installation of the blower is complete, reinstall the
internal frame and filters. Refer to complete the instal-
lation on page 17.
IMP RTANT N TE: Before turning electrical power on to
the ventilation hood, make sure the blower is off.
THREADED
STUD
HEX NUT
SLOT
TAB
Internal blower.

Pro sland Hood nstallation 15
wolfappliance.com/specs
n-Line and Remote Blowers
WIRING F R IN-LINE R REM TE BL WER
1) Remove the hood electrical box cover. Run Romex®
wire from a 120 V AC, 15 amp circuit to the hood
installation location. nsert the Romex®wire into the
electrical box by running it through the wire clamp
previously installed. Tighten the wire clamp to secure
the wire. Refer to the illustration and chart on the
previous page for the location of wiring for your
specific hood.
2) Run the blower cable to the installation location. nsert
the blower cable into the electrical box by running it
through the other wire clamp previously installed.
Tighten the wire clamp to secure the cable.
3) Cut off the butt crimp connector from the end of
orange wire in hood. Strip orange wire about 3/8" (10).
Using an appropriate wire connector (not included),
connect black wire from blower to orange wire in hood.
4) Using the wire connectors provided, connect black
wire to power supply black wire, all white wires
together and green or bare wires from power supply
and blower to green ground screw in the electrical box.
5) Place all wiring connections inside the electrical box
and reinstall the cover. Make sure all wires are secure
and that no wires are pinched between the cover and
electrical box.
Before making electrical connections, make sure the
electrical power is turned off at the service panel.
Do not run wiring through the ductwork.

IN-LINE AND REM TE BL WER DIMENSI NS
18"
(457)
22"
(559)
247/8"
(632)
12"
(305)
18"
(457)
8"
(203)
1100 CFM in-line blower.
900 CFM remote blower. 1500 CFM remote blower.
1200 CFM remote blower.
241/2"
(622)
151/2"
(394)
281/4"
(718)
203/4"
(527)
243/4"
(629)
14"
(356)
43/4"
(121)
10" (254)
DIAMETER
143/4"
(375)
291/2"
(749)
291/2"
(749)
18" (457)
22"
(559)
101/8"
(257)
71/4"
(184)
10"
(254)
10" (254)
DIAMETER
143/4"
(375)
291/2"
(749)
291/2"
(749)
21" (533)
25"
(635)
103/8"
(264)
71/4"
(184)
10"
(254)
10" (254)
DIAMETER
n-Line and Remote Blowers
BL WER INSTALLATI N
IMP RTANT N TE: Refer to specific installation instruc-
tions provided with each blower assembly for additional
mounting and wiring instructions.
Locate the blower so that the length of the duct run and
number of elbows and transitions are kept to a minimum.
The duct run should be no longer than 50' (15 m). Remote
blowers should be located between wall studs or roof
rafters. Avoid pipes, wires and other ductwork.
Allow enough space for transitions needed between the
blower and connecting ductwork. For best performance,
locate transitions nearest the blower.
Refer to the illustrations below for overall dimensions of
Wolf in-line and remote blowers. nstallation instructions
shipped with each Wolf ventilation product provide
detailed specifications. These instructions can also be
found on our website, wolfappliance.com/specs.
Pro sland Hood nstallation 16
Before making electrical connections, make sure the
electrical power is turned off at the service panel.

Pro sland Hood nstallation 17
wolfappliance.com/specs
Complete the nstallation
INSTALL FILTERS
Reinstall the internal frame on the island hood. Refer to
hood preparation on page 11.
Slide the grease cups along the bottom edge of the hood
so that the lip of the grease cup overhangs slightly.
To install the filters, orient each filter with lines running
vertically. Position the top edge of the filter as shown in
the illustration below. While pressing up against the
spring, rotate the bottom edge of the filter into position
next to the grease cup. Gloves should be worn when
handling filters.
L G NAMEPLATE
The Wolf logo nameplate does not come installed on the
island hood since there are various locations that the
nameplate can be attached.
Once you've decided on the location for the nameplate,
clean the mounting area with rubbing alcohol. Remove the
backing paper from the nameplate. Position the nameplate
aligned parallel with the bottom edge of the hood and
press into place.
GREASE CUP SIDE VIEW
FILTER
SPRING
Filter installation.

Service nformation 18
Troubleshooting
IMP RTANT N TE: f the pro ventilation hood does not
operate properly, follow these troubleshooting steps:
•Verify that electrical power is being supplied to the
ventilation hood.
•Check electrical connections to ensure that the
installation has been completed correctly.
•Refer to the troubleshooting guide in the Wolf pro
ventilation hoods use & care guide.
•f the ventilation hood still does not operate properly,
contact a Wolf authorized service center. Do not
attempt to repair the ventilation hood yourself. Wolf is
not responsible for service required to correct a faulty
installation.
Service nformation
f service is necessary, maintain the quality built into your
ventilation hood by calling a Wolf authorized service
center.
To obtain the name and number of a Wolf authorized
service center, check the contact & support section of our
website, wolfappliance.com or call Wolf customer service
at 800-332-9513.
When calling for service, you will need the model and
serial numbers of the ventilation hood. This information is
found on the product rating plate, located inside the left
wall of the hood shell. Refer to the illustration below.
Location of rating plate
(inside hood).
RAT NG PLATE
Before servicing or cleaning, switch power off at the
service panel and lock the service disconnecting means
to prevent power from being switched on accidentally.
If it cannot be locked, securely fasten a prominent
warning tag, to the service panel.

The information and images in this guide are the copyright property of Wolf Appliance, nc. Neither this guide nor any information or images contained herein
may be copied or used in whole or in part without the express written permission of Wolf Appliance, nc. ©Wolf Appliance, nc. all rights reserved.
Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, nc.
Sub-Zero, Sub-Zero & Design, Dual Refrigeration, Constant Care and The Living Kitchen are registered trademarks and service marks of Sub-Zero, nc.
(collectively, the “Company Marks.”) All other trademarks or registered trademarks are property of their respective owners in the United States and other countries.

W LF APPLIANCE, INC. P. . B X 44848 MADIS N, WI 53744 W LFAPPLIANCE.C M 800.332.9513
817001 REV-A 8/2010