Wolf 13005870 Service manual

WARMING DRAWER
Installation Information
2-2
INSTALLATION INFORMATION
The Wolf warming drawer is designed to be set into a built-in wall or cabinet installation.
This section of the manual covers some of the installation issues that a service technician may need to know when
servicing a Wolf warming drawer. If additional installation information is needed after reviewing this section of the
manual, please refer to the installation guide or contact the Wolf Appliance Customer Service Department.
Electrical Requirements
• 110 to 120 Volts AC, 60Hz, 15 ampere fused electrical supply
• Separate electrical circuit serving only this appliance
• A properly grounded 3-prong receptacle
Line
Voltage
(Power)
Neutral
Ground
•TOAVOID SHOCK HAZARD, THE INSTALLATION SITE MUST BE EQUIPPED WITH APROPERLY
GROUNDED 3-SLOT RECEPTACLE TO MATCH THE 3-PRONG (GROUNDED) POWER SUPPLYCORD
PROVIDED ON THE APPLIANCE.
•TOAVOID SHOCK HAZARD, NEVER REMOVE THE GROUND PRONG FROM THE PLUG OF THE POWER
SUPPLYCORD.
Ground Prong
Figure 2-1. Electrical Receptacle & Power Cord
#802981 Rev. A Jan. 2005

FRAME
29-7/8"
(759)
23"
(584)
23-1/2" min
(597)
*28-1/2"
(724)
FRAME
10-1/4"
(260)
*9-1/4"
(235)
E
NOTE:
If installed below Wolf
wall oven, rail between
appliances must be
minimum 1-1/4” (318 mm) thick.
E
4"
(102)
5"
(127)
* Dimension may vary by ± 1/8" ( ± 3 mm)
= Electrical outlet location
NOTE:
1.5" X 1.5"
(3.8 mm X 3.8 mm)
A
nti-Tip Block
must be installed.
NOTE: Dimensions in parentheses are in millimeters.
Installation Information
WARMING DRAWER
2-3
Installation Specifications (Non-Integrated)
The warming drawer is designed to be set into a built-in installation alone, or in combination with a Wolf wall oven,
microwave oven or cooktop. The illustration below shows the rough-in dimensions for a “non-Integrated” warming
drawer installation below a wall oven (See Figure 2-2).
NOTE: Prior to serial #13005870, the warming drawer could not be installed in an Integrated application. See
rough-in dimensions for an Integrated application on following page.
For complete installation instructions, refer to the installation guide.
Figure 2-2. Non-Integrated Warming Drawer Installation below a Wall Oven
#802981 Rev. A Jan. 2005

WARMING DRAWER
Installation Information
2-4
E
FRAME
29-7/8"
(759)
25-1/2" min
(648)
*29-15/16"
(760)
FRAME
10-1/4"
(260)
*10-3/8"
(264)
* Dimension may vary by ± 1/8" ( ± 3 mm)
4"
(102)
E
= Electrical outlet location
NOTE:
1.5" X 1.5"
(3.8 mm X 3.8 mm)
A
nti-Tip Block
must be installed.
5"
(127)
NOTE:
If installed below Wolf
wall oven, rail between
appliances must be
minimum 2-3/8” (60 mm) thick.
NOTE: Dimensions in parentheses are in millimeters.
23"
(584)
BACK OF
UNIT TO
BACK OF
FRAME
Minimum required cabinet width = 33" (838 mm)
Minimum required cabinet depth = 26" (660 mm)
NOTE:
Installation Specifications (Integrated) - Starting with Serial #13005870
The illustration below shows the rough-in dimensions for an “Integrated” warming drawer installation below a wall
oven (See Figure 2-3).
NOTE: Prior to serial #13005870, the warming drawer could not be installed in an Integrated application.
For complete installation instructions, refer to the installation guide.
Figure 2-3. Integrated Warming Drawer Installation below a Wall Oven
#802981 Rev. A Jan. 2005