Wondrwall Smart Switch User manual

13
12
Installing
We’ve designed Wondrwall to be as compatible with as many
homes as possible. The only pre-requisites are:
yYour existing light switches must have aneutral line in place.
If you are unsure, consult aqualified electrician.
yYou must have awireless router with internet access
available in the home.
yYou must have atraditional ‘wired’ thermostat in place,
which can be replaced with our thermostat (this usually only
takes around 15 minutes).
The system will work if installed with just the base kit, but with
limited functionality. Our recommendation is replacing the
standard light switches throughout the home to experience the full
power of Wondrwall.
The following pages explain how to install each component and pair
it with your home wireless network.

15
14
A
B
N L
When you install the light
switch, you will be dealing
with mains voltages (230
Vac).
If you are unsure about
how to do this, use aNICEIC
approved electrician.
!Inputs
Outputs
L1
N1
L2
N2
L3
N3
Light Switch
The light switch replaces astandard light switch. For the primary
light switch, choose one that is close to your wireless internet
router or near the middle of your home.
1. Switch othe mains power supply that supplies the light switch.
Remove the old light switch.
2. Pull the side of the Wondrwall light switch cover towards you to
unclip it from the base (A).
3. Connect the Live and Neutral input cables to the L and N
connectors on the back of the light switch base (B). The
connection screws are above the cable entry points.
4. Connect the Live and Neutral output cables to the lights:
yIf you only use 1 lighting circuit, use connections L1/N1. The
middle LED will light.
yFor 2 circuits, use L2/N2 and L3/N3. The outer LEDs will light.
yFor 3 circuits use all output connections. All LEDs will light.

1716
5. Fix the light switch base to the wall. It uses the same holes as
your old light switch. Screws are supplied.
6. Clip the light switch cover back onto the base.
7. You can now pair the light switch with other Wondrwall
components (see page 30).
8. Repeat this for each light switch that you want to use.
Thermostat
The Wondrwall thermostat replaces your existing thermostat, or for
new installations, locate it about 1.5 m (5 feet) othe floor. Site it
away from any heating or cooling sources such as direct sunlight,
hot water pipes or fireplaces. lamps, outside doors or windows,
damp areas or areas that lack air circulation.
If you are unsure about how to do this, or prefer not to
perform this task, consult aNICEIC approved electrician
or licensed HVAC professional.
1. Switch othe electricity supply to your HVAC unit or boiler and
remove the cover from the old thermostat.
2. Make anote of the terminal location for each wire connected to
the thermostat wiring terminals.
3. Remove each wire from the old thermostat and secure them so
they do not fall back into the wall. Attach alabel to each wire as
you indentify each wire to ensure that you match the correct
wire and terminal.
!

19
18
4. Remove the old thermostat from the wall. Leave at least 75
mm (3”) of wire for each connection to the thermostat wiring
terminal. Remove 3 mm (1/8”) of insulation from each wire and
twist the wires to give asturdy end.
5. Remove the cover from the Wondrwall thermostat. Hold onto
the ribbon loop on the back of the thermostat and pull the
cover forwards.
6. Hold the thermostat base against the wall where you intend to
mount it and mark the three mounting holes (A).
7. Drill the mounting holes and insert the wall plugs (if necessary).
Pull the cables through the hole in the base (B) then use a
Philips screwdriver to screw the thermostat base to the wall.
8. Connect the wires: Push down the orange spring clip (C) of the
correct connector and insert the wire fully into the correct hole
(D). Release the spring clip. Check the wire is secure.
9. Replace the thermostat cover. Push it so it clicks and covers the
base.
10. Turn on the power to your HVAC system or boiler.
AA
A A
B
Cool control /
compressor
Heat pump c/o (+
in heat)
Fan Heat pump c/o (+
in cool)
Heat control 2nd stage heat /
aux heat
Power from cooling 2nd stage cool
control
Power from heating Common
DC

21
20
You can now pair the thermostat with other Wondrwall components
(see page 34).
Things to be aware of when installing the thermostat:
1. If you have separate power for RH and RC, you need to remove
the factory installed jumper between RH and RC.
2. Many systems do not provide acommon ‘C’ wire. In this case,
install 4 AA batteries for the unit to operate.
3. The thermostat automatically detects your system type by
the connections you make. The display will show ‘E0’ until the
unit has been properly connected and reset (by pulling oand
refitting the front cover).
4. The thermostat is configured to work with single-stage cool,
single-stage gas, oil or fuel heat (non-heat pump, single-speed
fans. If your system is dierent, refer to the programming
section on page 57 to configure the thermostat to your
system.

23
22
A
B
Siren
The siren has awaterproof case and is designed to be mounted on
an exterior wall of your property.
Mount the siren as high as possible so its siren and strobe light will
attract attention when an alarm is activated.
Three wall plugs and screws are supplied to mount it to the wall.
Remove the cover:
1. Use aPhilips screwdriver to loosen the bottom screw (A) until
the screw head is clear of the cover.
2. Carefully pull the bottom of the cover until it clears the screw,
then remove the cover.
Mount the siren:
3. Hold the siren base against the wall where you intend to mount
it and mark the three mounting holes (B). Drill the holes and
insert the wall plugs.

25
24
4. Before you mount the siren, we recommend that you pair the
siren with the Wondrwall system (page 37).
5. Switch the battery switch to ON (C).
6. Test that the siren operates correctly. To do this, arm the alarm
from the Wondrwall app, then move in front of amotion sensor.
7. Use aPhilips screwdriver to screw the siren base to the wall.
Make sure the tamper switch (D) is fully depressed against the
wall. (If there is agap, pack it with suitable spacing material).
Replace the cover:
8. Hook the lip at the top of the cover over the top of the base
9. Carefully push the bottom of the cover towards the base so that
the bottom screw slides into the slot on the cover (E).
10. Tighten the bottom screw using aPhilips screwdriver.
D
E
C

27
26
Connecting
The Wondrwall system uses energy ecient ZigBee technology that
ensures reliable operation without impacting your already crowded
Wi-Fi setup.
Every light switch has in-built wi-fi, allowing them to operate
independently but which is also the means by which the main
device connects to the cloud and the machine learning and
predictive modelling platform. Even if the wi-fi goes down, the
Wondrwall system continues to operate since each switch has its
own operating.
Bluetooth is included in every switch to allow them to pair to any
other Bluetooth device opening ahuge range of possibilities.
To set up the Wondrwall network, you must first pair the primary
light switch to your wireless router and network, using the
Wondrwall App which is available on the App Store and on Google
Play.

29
28
C
FG
B
E
A
D
Pair the primary light switch
The primary light switch will be the main hub of the Wondrwall
network. Select the light switch in the middle of your home, nearest
to your wireless router.
1. Open the Wondrwall app and display the Devices screen (A).
2. Press the +in the top right hand corner of the screen to open
the Install wizard. Select Light switch from the list (B).
3. Remove the front cover of the light switch and insert something
thin into the small hole on the front to press the pairing button
(C).
4. Follow the on-screen instructions to specify the light switch
wi-fi, join your wireless network (D), to set your home location
(E) and to configure the primary light switch (F).
5. When the light switch has successfully paired, either click
Finish on the Success screen (G) to end the installation or Add
another device to continue pairing the rest of your Wondrwall
devices.

33
32
A
F
BC
ED
Pair the key fobs
1. Either click Add another device in the Success screen (A), or
the +on the Devices screen (B) to open the Install wizard.
2. Select Key Fob from the list (C).
3. Press the button on the key fob (D).
4. Follow the on-screen instructions to configure the key fob (E).
5. When the key fob has successfully paired, click Add another
device to repeat this procedure with the second key fob.
6. Click Finish on the Success screen (F) to end the installation
or Add another device to continue pairing the rest of your
Wondrwall devices.

35
34
Pair the thermostat
1. Either click Add another device in the Success screen (A),
or the +on the Devices screen (B) to open the Install wizard.
Select Thermostat from the list (C).
2. Press the MODE button on the front of the thermostat (D)
until OFF is displayed on the screen. Press and hold the space
between the HOLD and FAN buttons and at the same time,
swipe afinger down the right-hand slider. The display will
change to 01.
3. Press the icon on the slider until the display reads 12, then
press HOLD. This enters the ‘Join Network’ menu.
4. Press the icon again to display 01 and press HOLD to pair
with the Wondrwall network, then press MODE.
5. Follow the on-screen instructions to configure up the
thermostat (E).
6. When the thermostat has successfully paired, either click
Finish on the Success screen (F) to end the installation or Add
another device to continue pairing the rest of your Wondrwall
devices.
A B C
D FE

37
36
A B C
D
FE
Pair the siren
We recommend that you pair the siren before you fix it to the wall.
1. Either click Add another device in the Success screen (A),
or the +on the Devices screen (B) to open the Install wizard.
Select Siren from the list (C).
2. Remove the cover (page 23).
3. Push the function button (D) for 10 seconds. The right hand LED
will flash. Release the button. The siren is now connected to the
Wondrwall network.
4. Follow the on-screen instructions to configure up the
thermostat (E).
5. When the thermostat has successfully paired, either click
Finish on the Success screen (F) to end the installation or Add
another device to continue pairing the rest of your Wondrwall
devices.
6. Replace the cover (page 24).