Wood Stone PHOENIX 4343 PITA OVEN User manual

Tel [phone]
Fax [phone]
www.woodstone-corp.com
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
PHOENIX OVEN
Stone Hearth Oven
Dual Radiant Flame Burners, Gas-Fired Models
PHOENIX 4343 PITA OVEN WS-BL-4343-RFG-LR
PHOENIX 4355 PITA OVEN WS-BL-4355-RFG-LR
PHOENIX 4836 PITA OVEN WS-BL-4836-RFG-LR
DOC NO M0030.10 REVISED JANUARY 2020
Installation and
Operation Manual

Dual Burner Phoenix Installation
and Operation Manual
PG 2 OF 32
M0030.10 JANUARY 2020
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
TABLE OF CONTENTS
TABLE OF CONTENTS
Dual Burner Phoenix Oven . . . . . . . .3
Cautions & Warnings . . . . . . . . . . .4
Specifications
PX-4343-LR . . . . . . . . . . . . . . .6
PX-4355-LR . . . . . . . . . . . . . . .7
PX-4836-LR . . . . . . . . . . . . . . .8
Moving & Placing the Oven. . . . . . . .9
Installation Clearances . . . . . . . . .10
Venting . . . . . . . . . . . . . . . . . . .11
Flue Adapter Installation . . . . . . . .12
Lifting the Oven. . . . . . . . . . . . . .13
Exploded Parts Diagram . . . . . . . .15
Assembly . . . . . . . . . . . . . . . . .16
Utility Connections . . . . . . . . . . . .21
Storage Box Installation . . . . . . . . .24
Controller . . . . . . . . . . . . . . . . .25
Initial Start-Up. . . . . . . . . . . . . . .26
Oven Operation . . . . . . . . . . . . . .27
Daily Maintenance . . . . . . . . . . . .28
Troubleshooting Guide. . . . . . . . . .29
Electrical Diagrams . . . . . . . . . . .30
Interlock Diagram . . . . . . . . . . . .31
Limited Warranty . . . . . . . . . . . . .32

INSTALLATION AND OPERATION MANUAL FOR
THE WOOD STONE DUAL BURNER PHOENIX
NATURAL GAS OR PROPANE FUELED DUAL BURNER STONE HEARTH OVEN
WS-PX-4343-RFG-LR, WS-PX-4355-RFG-LR AND WS-PX-4836-RFG-LR
ADDITIONAL COPIES AVAILABLE UPON REQUEST
Dual Burner Phoenix Installation
and Operation Manual
PG 3 OF 32
M0030.10 JANUARY 2020
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
DUAL BURNER PHOENIX OVEN
Shown: WS-PX-4343-RFG-LR

IMPORTANT: Consult your local gas supplier for a statement outlining a procedure to be followed in the
event you smell gas. Post the statement in a prominent location.
When this oven is not properly installed, a fire may result. To reduce the risk of fire,
follow the installation instructions. It is recommended that this oven be installed, maintained
and serviced by authorized professionals.
WARNING: Improper installation, adjustment, alteration, service or maintenance can result in property
damage, injury or death. Read the installation, operation and maintenance instructions thoroughly before
installing or servicing this equipment.
AVERTISSEMENT: L’installation, le réglage, la modification, la réparation ou l’entretien incorrect de
cet appareil peut causer des dommages matériels, de blessures ou la mort. Lire attentivement les
instructions d’installation, de fonctionement et d’entretien avant de procéder à son installation ou
entretien.
INSTALLATION AND OPERATION MANUAL FOR THE WOOD STONE PHOENIX
NATURAL GAS (NG) OR PROPANE (LP) FUELED DUAL BURNER STONE HEARTH OVEN
WS-PX-4343-RFG-LR-(NG OR LP), WS-PX-4355-RFG-LR-(NG OR LP)
ADDITIONAL COPIES AVAILABLE UPON REQUEST
READ ALL INSTRUCTIONS BEFORE INSTALLING AND USING THIS APPLIANCE
Please read this entire manual before you install the oven. Failure to follow instructions may result
in property damage, bodily injury or even death. Contact your local building or fire officials about
restrictions and installation inspection in your area.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
Additional copies of this manual are available at woodstone-corp.com.
For prompt responses to service/maintenance questions, call your local distributor.
Dual Burner Phoenix Installation
and Operation Manual
PG 4 OF 32
M0030.10 JANUARY 2020
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
CAUTIONS & WARNINGS

SAVE THE INSTRUCTIONS
FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors or liquids in the vicinity of
this or any other appliance.
POUR VOTRE SÉCURITÉ: Ne pas entreposer ni utiliser d’essence ou d’autres vapeurs de liquides
inflammables ou des liquides dans les environs de ce ou de tout autre appareil.
This appliance is for professional use by qualified personnel. This appliance must
be installed by qualified persons in accordance with the regulations in force. This
appliance must be installed with sufficient ventilation to prevent the occurrence of
unacceptable concentrations of substances harmful to health in the room in which
it is installed. This appliance needs an unobstructed flow of fresh air for satisfactory
combustion and must be installed in a suitably ventilated room in accordance with
current regulations. This appliance should be serviced by qualified personnel at least
every 12 months, or sooner if heavy use is expected.
!
A MAJOR CAUSE OF OVEN RELATED FIRES IS A
FAILURE TO MAINTAIN REQUIRED CLEARANCES
TO COMBUSTIBLE MATERIAL. IT IS OF UTMOST
IMPORTANCE THAT THIS OVEN BE INSTALLED ONLY
IN ACCORDANCE WITH THESE INSTRUCTIONS.
Dual Burner Phoenix Installation
and Operation Manual
PG 5 OF 32
M0030.10 JANUARY 2020
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
CAUTIONS & WARNINGS

UTILITIES SPECIFICATIONS
Gas
19mm (3/4") FNPT gas inlet
105,000 BTU/hr Natural Gas (NG)
OR
105,000 BTU/hr Propane (LP)
Maximum gas inlet pressure
34 mbar (1/2 psi or 14 inches W.C.)
Electrical
120 VAC, 2 A, 60 Hz
Optional: 240 VAC, 1 A, 60 Hz
All utility connections made on the back
of the oven control box. Remove front or
rear panel for access Use utility knockouts
(provided) to route gas and electrical
supplies. Refer to data plate when installing.
Venting
The Phoenix must be vented using an approved
chimney, or an exhaust hood constructed and
installed in accordance with all relevant local and
national codes. Remove round collar if venting with
an exhaust hood
Side view
Rear view
Plan view
G
10"
250mm ID
42 1/4"
1070mm
50"
1270mm
42 1/4"
1070mm
34 1/2"
880mm
AIR INTAKE
6"
150mm
27 1/2"
700mm
24 1/2"
620mm
9 3/4"
250mm
7 1/2"
190mm
3 3/4"
90mm
10 1/4"
260mm
8"
200mm
3 1/2"
90m
20 1/4"
510mm
8"
200mm
47 1/4"
1200mm
37"
940mm
7 1/2"
190mm
40"
1020mm
69 3/4"
1770mm
29 3/4"
760mm
6"
150mm
3 1/2"
90mm
1 1/2"
40mm
Front view
Actual weight
1,650 lbs.
Shipping weight
2,100 lbs.
Air intake: Do not
facade or cover over
Must be left
removable for service
9 1/4"
240mm
Knockouts provided
on Rear Panel for gas/
electrical connection
Rear Panel MUST
be installed
Dual Burner Phoenix Installation
and Operation Manual
PG 6 OF 32
M0030.10 JANUARY 2020
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
PX-4343-LR SPECIFICATIONS
4343 (CS-REC-9) SPECIFICATIONS

UTILITIES SPECIFICATIONS
Gas
19mm (3/4") FNPT gas inlet
151,000 BTU/hr Natural Gas (NG)
OR
151,000 BTU/hr Propane (LP)
Maximum gas inlet pressure
34 mbar (1/2 psi or 14 inches W.C.)
Electrical
120 VAC, 2 A, 60 Hz
Optional: 240 VAC, 1 A, 60 Hz
All utility connections made on the back
of the oven control box. Remove front or
rear panel for access Use utility knockouts
(provided) to route gas and electrical
supplies. Refer to data plate when installing.
Venting
The Phoenix must be vented using an approved
chimney, or an exhaust hood constructed and
installed in accordance with all relevant local and
national codes. Remove round collar if venting with
an exhaust hood
Side view
Rear view
Plan view
G
54 1/4"
1380mm
62"
1570mm
42 1/4"
1070mm
46 1/2"
1180mm
O10"
250mm ID
AIR INTAKE
24 1/2"
620mm
7 1/2"
190mm
27 1/4"
690mm
8"
200mm
20 1/4"
510mm
4 1/4"
110mm
6"
150mm
9 3/4"
250mm
10 1/4"
260mm 8" 200mm
O
69 3/4"
1770mm
7 1/2"
190mm
47"
1200mm
37"
940mm
29 3/4"
760mm
40"
1020mm
6"
150mm
3 1/2"
90mm
O
1 1/2"
40mm
9 1/2"
240mm
O
6 1/2"
160mm
6 1/2"
160mm
Front view
Actual weight
2,200 lbs.
Shipping weight
2,500 lbs.
Air intake: Do not
facade or cover over
Must be left
removable for service
Knockouts provided
on Rear Panel for gas/
electrical connection
Rear Panel MUST
be installed
Dual Burner Phoenix Installation
and Operation Manual
PG 7 OF 32
M0030.10 JANUARY 2020
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
PX-4355-LR SPECIFICATIONS
4355 (CS-REC-11) SPECIFICATIONS

UTILITIES SPECIFICATIONS
Gas
3/4 inch FNPT gas inlet
105,000 BTU/hr Natural Gas (NG)
OR
100,000 BTU/hr Propane (LP)
Maximum gas inlet pressure
34 mbar (1/2 psi or 14 inches W.C.)
Electrical
120 VAC, 2 A, 50/60 Hz
Optional: 240 VAC, 1 A, 50/60 Hz
All utility connections made on the back
of the oven control box. Remove front or
rear panel for access Use utility knockouts
(provided) to route gas and electrical
supplies. Refer to data plate when installing.
Venting
The Phoenix must be vented using an approved
chimney, or an exhaust hood constructed and installed
in accordance with all relevant local and national codes.
Remove round collar if venting with an exhaust hood
Side view
Rear viewPlan view
G43"
1090mm
47 3/4"
1210mm
35 1/2"
900mm
O10"
250mm ID
27 3/4"
700mm
AIR INTAKE
9 3/4"
250mm
24 1/2"
620mm
6"
150mm
10 1/2"
270mm 7 3/4" 200mm
3 1/2"
90mm
4 1/4"
110mm
7 1/2"
190mm
20 1/4"
510mm
8"
200mm
27 3/4"
700mm
O
47 1/4"
1200mm 37 1/4"
940mm
160mm160mm
70"
1780mm
7 1/2"
190mm 29 3/4"
760mm
3 1/2"
90mm
6"
150mm
O
40 1/4"
1020mm
1 1/2"
40mm
9 1/2"
240mm
6 1/4"
160mm
6 1/4"
160mm
O
Front view
Actual weight
1,650 lbs.
Shipping weight
1,850 lbs.
Air intake: Do not
facade or cover over
Must be left
removable for service
Knockouts provided
on Rear Panel for gas/
electrical connection
Rear Panel MUST
be installed
47 1/4"
1213mm
Dual Burner Phoenix Installation
and Operation Manual
PG 8 OF 32
M0030.10 JANUARY 2020
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
PX-4836-LR SPECIFICATIONS

Minimum Required Forklift Capacities
Model
Shipping Weight
(kg/lbs)
Required Forklift
Capacity (lbs/kg)
Min. Fork
Length (ft/m)
PX-4343-LR 953 kg
(2,100 lbs)
1450 kg
(3,200 lbs)
1.5m
(5')
PX-4355-LR 1134 kg
(2,500 lbs)
2268 kg
(5,000 lbs)
PX-4836-LR 816 kg
(1,800 lbs)
1450 kg
(3,200 lbs)
The oven should
only be moved using
a Pallet Jack on a
smooth, LEVEL FLOOR.
Use a Forklift
or other suitable
means if the oven
must be moved over
an inclined surface.
LEVELING AND SHIMMING THE OVEN.
The installed oven must be level. Use metal shims to level the oven if necessary. Because the weight of the oven is carried by the full
perimeter of the oven stand, make certain there no gaps larger than approximately 13mm (1/2") where the oven stand is unsupported
by shims. Seal any small gaps between the oven and the floor with silicone. Failure to solidly support the full perimeter of the oven
stand can result in costly damage to the oven and will void the warranty. The floor design and construction must be adequate to
handle the weight of the oven.
Please see woodstone-corp.com for floor loading information.
USING A FORKLIFT | PALLET JACK
Phoenix ovens are very top-heavy. If the oven tips it can
cause severe injury or death. Never use a Hand Truck to
move the oven. The oven should only be moved using a
Pallet Jack on a smooth, LEVEL FLOOR. If the oven must
be moved over an inclined surface, a Forklift or other suitable
means should be employed. If the installer does not have the
equipment or experience required to move the oven safely, we
recommend securing the services of a qualified rigging company.
The oven should only be moved using a Pallet Jack on a
smooth, LEVEL FLOOR.
ÜÜÜÜ
Make sure the
Pallet Jack wheels
do not contact the
underside of the
fork pocket when
lifting to avoid
damaging the stand.
PICKEYE CAPACITIES PER BEAM
907 kg (2,000 lbs): Middle holes (PX-4343-LR, PX-4355-LR)
1225 kg (2,700 lbs): Outer holes (PX-4836-LR)
INNER INNER
MIDDLE MIDDLE
OUTER OUTERBOLT POSITIONS
Never use a Hand Truck
to move the oven.
MOVING THE OVEN.
LOAD
Orient Spreader Bar
as shown in fig. 1
50°MIN Angle
WARNING
If you received your Phoenix oven disassembled, go to the ASSEMBLY section.
If you need to disassemble the oven to move it through a narrow door or passageway,
see the DISASSEMBLY section in this manual.
If the oven is to be installed against a wall, leave access to the back of the oven to complete the utility connections.
Pickeye
Beam
Shown:
BL-4343-LR
fig. 1
USING A CRANE.
The oven arrives with Pickeyes attached. When craning a Wood Stone oven, use a Spreader Bar with a
two-legged sling rigged on each end. The spreader bar should be of a sufficient length to keep the sling
from contacting the oven, and oriented as shown in fig 1.
Dual Burner Phoenix Installation
and Operation Manual
PG 9 OF 32
M0030.10 JANUARY 2020
MOVING & PLACING THE OVEN

CLEARANCES
1. The Wood Stone Phoenix oven must have a minimum 25 mm (1") clearance to combustibles from all sides, and 152 mm (6")
clearance to combustibles from the top. If building materials will contact the oven, they must be completely non-combustible.
Please note that standard Drywall (or Sheetrock) is considered a combustible. When non-combustible building materials
contact the body of the oven, the respective clearances are transferred to those non-combustibles.
2. Any facade 152 mm (6") to either side of the oven doorway or above, must be constructed of non-combustible building
materials.
3. For gas-only models, this oven is suitable for installation on combustible floors.
NOTICE: For stucco-ready appliances (model numbers ending in “-S”), the same clearances as described above apply. Non-
combustible stucco mix must be used and applied to a minimum thickness of 25mm (1").
WARNING: Installation and servicing of this product could expose you to glasswool/ceramic fibers as well
as calcium silicate dust. ALWAYS WEAR RESPIRATORY AND EYE PROTECTION WHEN INSTALLING OR
SERVICING THIS APPLIANCE. Please read this entire manual before you install the oven. Failure to follow
instructions may result in property damage, bodily injury or even death. Contact your local building or fire
officials about restrictions and installation inspection in your area.
!
WARNING: Do not pack required air spaces (clearance) with insulation or other material.
EN AVERTISSANT: N’emballez pas les espaces aériens requis avec l’isolation ou tout autre matériel.
When non-combustible building materials contact the body of the oven, the clearances to combustibles
are transferred to those non-combustibles.
!
Maintain 152 mm
(6") clearance
from top & all
sides of the flue
outlet*
Lined area 152 mm (6") to
either side of doorway and
above) represents space
where facade materials
must be non-combustible.
Hatched area must
be left accessible and
unobstructed after
installation for air intake
and routine service of the
oven burner.
1-inch minimum
side clearance
to combustible
construction
* For direct connect installations,
refer to local codes for duct
installation clearances
Gas-only models:
Suitable for installation
on combustible floors
Dual Burner Phoenix Installation
and Operation Manual
PG 10 OF 32
M0030.10 JANUARY 2020
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
INSTALLATION CLEARANCES