Woodhaven 4516 User manual

 Ifyou'reusingthestoponourUltraTrackwitha3/4"sub-fenceand
you'reusingourRulerBartoo,you'llwanttoattachthecursortothe
backofthestopbody.Installthetwo3/16"washers(WB001)onthe5/8"
screw(MT012),insertthescrewthrutheholeinthecursor(4519C)andstart
anut(NUT004) ontheendofthescrew.SlidethenutintheT-slotofthestop
body,adjustthecursorpositionontheRulerBarandtightenthescrew.
 Starting from the ribbed
sideofthestopbody,
insertthe1-1/2"hexbolt
(HB050)thruthecross
holeinthestop
bodyandattach
theknob(5540)
totheendof
thebolt.
 Identifyandverifythatyouhaveallthepartslisted.Readthe
instructionsatleastonce,familiarizingyourselfwiththepartsand
assemblyoptions,beforebeginningassembly.Thisstopisdesigned
tobeusedonthetopofourUltraTrackaluminumextrusion.
 Therearefourbasicwaystoassemblethestop,dependingon
whetheryouwantthestoparmontheleftorrightsideofthestopbody,
andwhetherornotyou'llbeusinga3/4"sub-fenceontheUltraTrack.
A:Ifyou'renotusinga3/4"sub-fence,mountthe
stoparmtothestopblocksotheT-slotinfaceofthestop
blockfacesthefrontofthetrack.See two Straight Stops
shown on left in fig. 2 and stop block in fig. 1.
4516 Curved Stop
& 4519 Straight Stop
Please Read Carefully!
Part Desc . . . . . Qty
4516A Curved Arm . . . . . . . . 1
or
4519A Straight Arm . . . . . . . . 1
4519B Stop Block . . . . . . . . . . 1
4519P Pivot Pin . . . . . . . . . . . 1
4519C Cursor . . . . . . . . . . . . . 1
5540 Knob ............... 1
HB050 1-1/2" hex bolt . . . . . . 1
Part Desc . . . . . Qty
WS001 1/4" Washer . . . . . . . . . 1
WN001 1/4" Washer . . . . . . . . . 1
MT012 5/8" Screw . . . . . . . . . . 1
WB001 3/16" Washer . . . . . . . 2
NUT004 10-24 Nut . . . . . . . . . . 2
NUT010A Locknut . . . . . . . . . . . . 1
MA002 10-24 Set Screw . . . . . 1
5786 3/32" Allen Wrench . 1
1
Parts List
NUT010A
on 4519P
Stop Arm:
4519A or
4516A
T-slot face of
Stop Block
NUT004 &
MA002
Allen
Wrench
WN001
5540
ASSEMBLY
 Clampthesmoothportionofthe
pivotpin(4519P) inavisewithnon-
marringjawsandscrewthelocknut(NUT010A)
onthethreadedendofthepivotpinuntil
thenutisflushwiththeendofthepin.
Insertthe1/4"steelwasher(WS001)on
thepivotpin(againstthenut),followed
bythestoparm(4516A or 4519A)
andthe1/4"nylonwasher(WN001).
Startthe10-24setscrew(MA002)
inoneofthe10-24nuts(NUT004).
Slidethenut/setscrewintotheT-slot
indicatedinthestopblock(4519B).
Insertthesmoothportionofthepivotpin(4519P)
inthediamond/squareshapedslotinthestopblock
and,usingthe3/32"allenwrench(5786)tightenthe
setscrewonthepivotpin,lockingthepivotpininthestop
body.Makesurethesetscrewnutisnotrubbingagainst
thenylonwasheronthepivotpin.Adjustthelocknuton
thepivotpintogetthedesiredamountoftensiononthe
stoparmsoitpivotsashardoraseasyasyoulike.
A
B
C
D
E
F
NUT010A
flush with end
of 4519P
4519P Pivot Pin
 B:Ifyouareusinga3/4"sub-fence,therounded
edgeofthestopblock(oppositefromtheT-slotside)
shouldfacethefrontofthetrack.See two Straight Stops
shown on right in fig. 2 and stop block in fig. 1.
WS001
NUT004
MT012
WB001 x2
4519C

2
 AttachtheassembledStoptothetopoftheUltra
TrackbyslidingtheboltheadintheT-slotoftheUltra
track.Positionwheredesiredandtightentheknob.

 Youcanreadthestoppositionbysightingalong
theoutsideedgeofthestoparmandeitherascaleon
ouroptionalRulerBar,orascaleplacedona3/4"sub-
fenceortheupperfrontfaceoftheUltraTrack.
OPTIONALACCESSORIES
 Theoptional4523 Micro Adjuster attachesto
eitherstopandallowsupto5/8"offineadjustment.
 Theoptional4517 ExtensionattachestotheStraight
Stoparmandprovidessupportforwidemiteredboards,etc.
 Theoptional4824, 4836 & 4848 Ruler Barattaches
tothebackupperT-slotoftheUltratrackandprovides
anadjustablescaleforreadingthestopposition.
©CopyrightWOODHAVENINC.11/17/10
(800)344-6657orWWW.WOODHAVEN.COM
4523
Micro
Adjuster
4517 Stop
Extension
4519
Right
Mount
4519
Left
Mount
4516
Left
Mount:
Subfence &
Pointer
4519
Right
Mount:
Subfence &
Pointer