World Market Leona 542373 User manual

Assembly Instructions
THANK YOU FOR YOUR PURCHASE. IF YOU HAVE ANY QUESTIONS
PERTAINING TO THE ASSEMBLY OF THIS FURNITURE PIECE, PLEASE CONTACT
THE NEAREST COST PLUS WORLD MARKET STORE.
IF YOU ARE NOT NEAR A STORE, PLEASE CALL OUR CUSTOMER SERVICE CALL
CENTER TOLL FREE AT 877-967-5362 FOR ASSISTANCE.
Page 1
Leona Farmhouse Side Chair
SKU - 542373
Date: 30/05/2017
Version #:1

LABEL
A
B
Back 1
Seat 1
DESCRIPTION QTY
Component
List
CRight Leg 1
DLeft Leg 1
ERight Stretcher 1
FLeft Stretcher 1
Hardware List
Tool List
LABEL DESCRIPTION
H-2
H-3
H-1
Long Bolt (M8x90mm)
Nut (M8x7mm)
Short Bolt (M8x40mm)
4
11
3
H-4
H-5
H-6
Screw (Ø4x50mm)
4
QTY
T-1
Spanner (M13mm)
1
T-2
Ball Allen Key (M4x30x110mm)
1
T-3 Phillips head screwdriver (tool needed) Not included
LABEL DESCRIPTION QTY
Spring Washer (Ø8xØ14x2mm)
11
Flat Washer (Ø8xØ20x2mm)
4
Big Hole
Medium Hole
Medium Tenon
Big Tenon
Small Tenon
Small Tenon
Page 2

Page 3
Assembly Preparation
A
Before Beginning:
C
D
F
E
B
Remove plastic
tube on bolts
Read instructions, cover to cover.
Have 2 adults on hand for assembly.
Save all packaging until
Assemble on a clean non-marring surface (packing foam).
Do not assemble on ooring or carpet.
In case of missing parts contact your nearest Cost Plus World Market store or our
customer service call center 877-967-5362.
Unpack all hardware bags and components to ensure you have all parts.

Page 4
Assembly Steps
Step 1
Step 2
Medium Tenon Big Tenon
T-1 H-2
H-3
H-4
2x
B
B
A
A
T-3
H-5
2x
H-1
T-1
H-3
H-4
3x
EF
Position Back (A) backside down onto a non marring padded surface on table top for ease
of assembly. Attach Seat (B) to Back (A). Secure Seat (B) to Back (A) with Long Bolts (H-2),
Spring Washer (H-3) and Flat Washer (H-4) for each corners; Short Bolts (H-1), Spring
Washer (H-3) and Flat Washer (H-4) between corners as shown using Ball Allen Key (T-1).
Do not fully tighten Bolts.
Position and assemble the Right Stretchers (E) and Left Stretcher (F) to Back (A) exactly
as shown below. Make sure all screw holes are facing up toward you. Secure all with
Screw (H-5) using Phillips Head Screw Driver (T-3).
Do not fully tighten Screws.

Page 5
Assembly Steps
Step 3
Attach Legs (C), (D) to Seat (B) and Right Stretcher (E) & Left Stretcher (F).
Secure Legs to Seat (B) with Nut (H-6), Spring Washers (H-3) and Flat Washers (H-4)
using Spanner (T-2). Secure Legs to Right Stretcher (E) & Left Stretcher (F)
with Screws (H-5) using Phillips Head Screwdriver (T-3).
Do not fully tighten Nuts and Screws.
Step 4
H-5
T-3
T-2
H-6
H-3
H-4
2x
2x
DD
C
E
E
FF
A
A
B
B
C
Fully tighten all Bolts; Nuts and Screws with Allen Key (T-1); Spanner (T-2) and
Phillips Head Screwdriver (T-3). Avoid using power driver to prevent over tightening.
T-3
T-1
T-2

Page 6
Assembly Steps
Step 5
Assembly complete.
Note: This will help increase the durability of the chair.
Check and tighten screws and bolts every 3 months, as necessary.

Care & Maintenance
Do not put hot items direct ly on furniture surface.
Do not clean furniture with harsh cleansers or polish.
Do not place furniture in direct sunlight.
Do not place furniture near
Do not write on furniture without a padded barrier to protect the surface.
Do not place furniture outside. For indoor use only.
Dust and pick-up spills using a clean, non-colored, lint-free cloth.
Stains may be removed with mild soap solution and damp cloth.
Not for commercial use. For residential use only.
Page 7
heating or cooling vents.
•
•
•
•
•
•
•
•
•