World Market Avila 602534 User manual

Page 1
THANK YOU FOR PURCHASE. IF YOU HAVE ANY QUESTIONS
PERTAINING TO THE ASSEMBLY OF THIS FURNITURE PIECE, PLEASE CONTACT
THE NEAREST COST PLUS WORLD MARKET STORE.
IF YOU ARE NOT NEAR A STORE, PLEASE CALL OUR CUSTOMER SERVICE CALL
CENTER TOLL FREE AT 877-967-5362 FOR ASSISTANCE.
Avila Extension Dining Table
SKU-602534
NOT FOR COMMERCIAL USE.
Assembly Instructions

Page 2
Component List
LABEL PICTURE DESCRIPTION QTY
ATable Top 1
B2
CTable Support Panel 2
DLeg Post
E1
Stretcher
F
Extension Table Top
Leg Base
2
2

Page 3
LABEL PICTURE DESCRIPTION QTY
H-1
T-1
Spring Washer
Ø13 x M8
Flat Washer
Ø17 x M8
Short Allen Bolt
M6 x 35mm
Allen Key
34
1
Hardware List
Tool List
LABEL PICTURE DESCRIPTION QTY
H-2
H-3
32
2
H-4 6
H-5 24
T-2 1
H-6 Medium Allen Bolt
M6 x 70mm
Connector Plate
Long Allen Bolt
M6 x 100mm
H-7
Screw
M6 x 3/4 Inch
Phillips Screw driver
( Not Included )
2
8

Page 4
Assembly Preparation
Before Beginning :
AB
C
D
E
H-1
H-2
H-3
H-4
H-5
H-6
H-7
•Unpack all hardware bags and components to ensure you have all parts-
•Read instructions, cover to cover-
•Have 2 adults on hand for assembly-
•Do not assemble on flooring or carpet-
•Assemble on a clean non-marring surface (packing foam)-
•Save all packaging until finished-
•In case of missing parts, please contact your nearest Cost Plus World
Market store or call our customer service call center at call 1-877-967-5362.
T-1
x 34
x 32
x 2
x 6
x 24
x 2
x 8
x 1
F
B
C
D
F
T-2 x 1

Page 5
Assembly Steps
STEP 1 : Attaching Foot Leg
H-1
H-2
Spring Washer (∅13xM8) x 8
Flat Washer (∅17x M8) x 8
H-7 Long Allen Bolt (M6 x 100) x 8
H-7
H-1
H-2
T-1
D
F
2X
STEP 2 : Attaching Stretcher
H-1 Spring Washer (∅13xM8) x 2
H-6
H-3 Connector Plate x 2
Medium Allen Bolt (M6x70) x 2
H-4 Screws (∅6 x 3/4 Inch) x 6 F
F
E
T-1
T-2
H-6
H-4
H-1
2X
TOP
Attach Leg Base (F) to Leg Post (D) using Long Allen Bolts (H-7), Spring Washer (H-1) and Flat Washer (H-2),
Stacking the hardware in the order as shown . Engage all bolts by hand first, then fully tighten using Allen Key
(T-1). Repeat this step for the second Leg (D/F) assembly.
TOP
Using a second person to assist you, insert Stretcher (E) into the corresponding notched hole at each Leg Base (F)
assembly as shown. Align Connector Plate (H-3) with the corresponding pre-drilled holes on the bottom of each Leg
Base (F) as shown. Start by securing the middle hole of the Connector Plate ( H-3) which will also secure the Stretcher
(E) using Medium Allen Bolts (H-6) and Spring Washers (H-1). Engage the bolts by hand, but do not fully tighten them
yet. Next, finish securing Connector Plate (H-3) using Screws (H-4) and a Phillips head screwdriver (not included).
Fully tighten all bolts and screws at this time using Allen Key (T-1) and a Phillips head screwdriver.

Page 6
Assembly Steps
STEP 3 : Attaching Support
H-1
H-2
Spring Washer (∅13xM8) x 8
Flat Washer (∅17x M8) x 8
H-5 Short Allen Bolt (M6 x 35) x 8
H-5
H-1
H-2
T-1
!C
C
DD
8X
STEP 4 : Assembling Top
H-1
H-2
Spring Washer (∅13xM8) x 16
Flat Washer (∅17x M8) x 16
H-5 Short Allen Bolt (M6 x 35) x 16
A
C
C
16X
H-5
H-1
T-1
H-2
Using a second person to assist you, carefully turn the assembly from Step 2 upright as shown. Align Table Support
Panels (C) with the corresponding pre-drilled holes on the tops of the Leg Posts (D) as shown. Note the orientation of
the support rails, they should face outwards as illustrated. Secure the Table Support Panels (C) using Short Allen Bolts
(H-5), Spring Washers (H-1) and Flat washers (H-2), stacking the hardware in the order as shown. Engage all bolts
then fully tighten them using Allen Key (T-1).
TOP
Using a second person to assist you, carefully lower Table Top (A) down into position onto Table Support Panels (C)
as shown. Secure Table Top (A) using Short Allen Bolt (H-5), Spring Washer (H-1) and Flat Washers (H-2), stacking
the hardware in the order shown. Engage all bolts by hand first, then fully tighten them using Allen Key (T-1)

Page 7
Assembly Steps
STEP 5 : Attaching Extension Table Top
STEP 6 : Lock Extension Table Top
Insert both Extension Table Tops (B) into position as shown, making sure the lower wooden support arms hook
under the main Table Top (A) assembly.
1
2
1) Ensure that the clasp ring on each toggle clamp has engaged the corresponding hook and then push the clamp closed
2) Next, make sure the hook has engaged the pin on the inner edges of both Table Support Panels.
Ensure that all bolts have been fully tightened at this time. Assembly is now complete and product is ready for use
NOTE : Levelers on the bottoms of the Leg
Bases may be used for additional leveling
adjustment if needed

Page 8
Care & Maintenance