World Tech Toys Sonic User manual

2.4GHz 4.5CH LIVE FEED VIDEO CAMERA RC DRONE

OUTDOOR FLIGHT PRECAUTIONS
PREVENTING MOISTURE
PROPER OPERATION
TRANSMITTER AA BATTERY SAFETY
DRONE BATTERY PACK SAFETY
KEEP AWAY FROM HEAT
INTRODUCTION
PRECAUTIONS
This drone is designed for outdoor flight. Please make sure there are no obstacles in
the flight path of the drone. Colliding into an obstacle while flying may damage the
drone. Make sure there is little to no wind when flying outside. Only fly the drone
when people are a safe distance away. Do not fly the drone within the vicinity of a
crowd. The spinning rotors may cause injury if the drone comes in contact with
someone.
Do not fly the drone outside when it is raining. Do not fly the drone close to open
water. If the drone’s comes in contact with water, it may short circuit the electronics
and damage the drone.
Do not modify or add anything to the drone. Modifying the drone may change its
ability to fly properly causing it to crash. Do not disassemble the drone.
Make sure the AA batteries in the transmitter are installed with the correct polarity.
Do not mix rechargeable AA batteries with non-rechargeable AA batteries. Do not
dispose of drained AA batteries into a fire. Batteries may explode if disposed in a fire
causing injury. Remove the AA batteries in the transmitter if you are not going to fly
the drone for a long period of time. Store AA batteries in a cool dry place. Keep AA
batteries away from heat.
The drone’s battery pack is Lithium polymer. LiPo batteries pose higher operational
risks compared to other battery packs so it’s important to follow the instructions when
using the battery. Manufacturer and dealer assume no liability for accidental
damages caused by improper usage.
Do not use a charger other than the factory supplied charger to avoid causing a fire or
damaging the battery pack. Do not try to disassemble, crush, burn or reverse polarity.
Make sure there are no metallic materials close to the contacts of the battery. Do not
charge the battery unsupervised.
Do not charge the battery overnight. Over charging the battery may damage it,
causing it to not hold a charge. Stop using or charging the battery if you notice the
battery temperature has increased more than usual.
The drone is made out of various plastics and metal. Plastics are very susceptible to
damage or deformation due to extreme heat and cold temperatures. Make sure not
to store the drone near any source of heat such as an oven or heater. It is best to
store the drone indoors in a climate controlled room temperature environment.
Thank you for purchasing this amazing World Tech Toys product. This drone is suitable for outdoor
flight. Please carefully read the entire manual before operating this drone and keep it for reference
in the future.

Drone Battery:
7.4V 1300mAh LiPo
Rechargeable Battery
RC Transmitter Battery:
4 x 1.5V AA Batteries
(Not Included)
20.86 inches
20.86 inches
6.5 inches
Length:
Width:
Height:
1.35 pounds
984 to 1640 feet
6 to 8 minutes
Approximately 150 minutes
Fuselage Weight:
Flight Area:
Flying Time:
Charging Time:
GENERAL SPECIFICATIONS
TRANSMITTER DIAGRAM
UP/DOWN GIMBAL (60 Degrees)
LIVE FEED VIDEO SCREEN
POWER SWITCH
POWER INDICATOR
LEFT TURN /
RIGHT TURN
LEFT TURN /
RIGHT TURN TRIM
LEFT STRAFE /
RIGHT STRAFE TRIM
THROTTLE
VIDEO SCREEN
POWER PLUG
FLIP STUNT BUTTON
LEFT STRAFE / RIGHT STRAFE
FORWARD / BACKWARD
AUTO RETURNPRESS
FORWARD /
BACKWARD TRIM
LEFT/RIGHT GIMBAL (120 Degrees)
LIGHT ON/OFF
HEADLESS MODEPRESS
SPEED TOGGLE
(LOW, MEDIUM, HIGH)
CAMERA / VIDEO CAMERA
CONTENTS: 1x Sonic Spy Drone 1x Wall Charger 1x 8GB Memory Card
1x Transmitter with Live Feed Video Screen 1x Instruction Manual
1x Screwdriver 1x Memory Card Reader 4x Spare Rotors

Attaching Live Feed Video Screen and Cradle
LIVE FEED VIDEO SCREEN OVERVIEW
Remove the screw on battery
cover and use the top tab to
pull open. Install 4 AA Batteries.
Please note the polarity.
Replace the battery cover and
screw once the batteries are
properly installed.
Line up antenna on
transmitter with the
screen cradle.
Press the cradle into
the antenna as
shown until it is
clicked into place.
Pull up on cradles
holster to open wide
enough to secure
live feed screen.
Insert the live feed
screen, plug into the
transmitter port on
top of transmitter.
INSTALLING TRANSMITTER BATTERIES
1.) Transmission signal strength.
2.) Transmitter frequency
channel.
3.) Controller battery level.
4.) Icon will display red when
recording.
5.) Live feed screen connector.
6.) Icon will display red when
taking a photo.
7.) Icon will show when no
memory card is inserted.
Correctly inserted memory
card will make icon disappear.

Open battery compartment
on rear of drone. Insert
battery and connect green
plugs. Close compartment.
Turn drone power switch
on located underneath
drone. Place on flat, level
surface clear for take off
and landing.
Turn transmitter on. Push
up on throttle to hear a
beep then push all the way
down to hear a shorter
beep. Drone is ready to fly.
BATTERY INSTALLATION & START UP
1.) Place drone upside down and take the
landing skid placing it into the slot on
frame. Make sure the screw hole on the
landing skid lines up with the hole in the
frame.
2.) Firmly screw in the landing skid to the
frame with a screwdriver.
3.) Repeat steps 1 and 2 for the other
landing skids.
LANDING SKIDS INSTALLATION
BATTERY COMPARTMENT
DRONE DIAGRAM
ROTOR BLADES
ROTOR GUARDS
VIDEO/PICTURE
CAMERA
LANDING SKIDS
MEMORY CARD SLOT
GIMBAL
LED LIGHTS
FRONT - GREEN LEDs
REAR - BLUE LEDs
1.) Transmission signal strength.
2.) Transmitter frequency
channel.
3.) Controller battery level.
4.) Icon will display red when
recording.
5.) Live feed screen connector.
6.) Icon will display red when
taking a photo.
7.) Icon will show when no
memory card is inserted.
Correctly inserted memory
card will make icon disappear.

CHARGING THE DRONE BATTERY PACK
ATTACHING CAMERA WITH GIMBAL
The drone battery pack can be recharged with the included wall charger. The battery needs to
be charged when the drones lights begin flashing or you notice a decrease in performance.
1.) Remove the battery pack from drone.
2.) Plug wall charger into standard outlet, red light will turn on.
3.) Connect the white battery pack cable to wall charger cable. LED will stay red while charging.
4.) After approximately 150 minutes the LED will turn green. Charging is complete.
*Do not leave charger charging unattended or overnight. Unplug charger promptly after charging
is complete to reduce risk of fire and/or injury.
Taking Photos and Video:
Press the camera button once to take a single image. Press and hold the camera button to start
recording video, to stop recording press and hold camera button again. The icons on live feed
screen will turn red while image or video is being taken and recorded to the memory card.
Gimbal Controls:
Turn knobs on transmitter to change position of camera before or during flight. The left knob
moves the camera up and down 60 degrees. The right knob rotates the camera left and right
120 degrees. During power up gimbal will move back to its starting forward position.
7.4V 1300mAh LiPo
Rechargeable Battery Pack Wall Charger
Flip drone over and make
sure the power switch is
turned off. Locate camera
locking tabs and make
note of install direction.
Line up the camera with
gimbal and slide into
locking tabs as shown until
secured.
Plug camera cable into the
port labeled, Cam Plug and
gimbal cables into Servo
Ports 1 and 2. Insert
memory card into back of
camera, clicking to secure.

FLYING THE DRONE
BASIC FLYING CONTROLS
Before flying the drone for the first time please read the instructions carefully and make sure
you fully understand how to control your drone.
Throttle
Move Forward /
Backward
Move Right /
Move Left
Left Spin /
Right Spin

ADJUSTING THE TRIM
RESETTING DRONE
When drone moves while hovering with no directional transmitter input, adjust the trim controls
until hovering is stable.
If the drone is spinning to the
left, push the RIGHT
TURNING TRIM button until
the drone stops spinning.
If the drone is spinning to the
right, push the LEFT
TURNING TRIM button until
the drone stops spinning.
If the drone is moving forward,
push the BACKWARD TRIM
button until the drone stops
moving forward.
If the drone is moving
backward, push the
FORWARD TRIM button until
the drone stops moving
backward.
If the drone is moving left,
push the MOVE RIGHT TRIM
button until the drone stops
moving left.
If the drone is moving right,
push the MOVE LEFT TRIM
button until the drone stops
moving right.
Forward
Trim
Backward
Trim
Move
Right Trim
Move
Left Trim
Move
Right Turn
Trim
Move
Left Turn
Trim
LAUNCH TOSS
Resetting may be necessary if trim adjustment is not working. Turn
on drone and place on a flat surface. Turn on transmitter and pair
to drone. Pull both joysticks to the bottom left corner, lights will
flash then return to normal when reset is complete.
After pairing with the transmitter you can launch your drone simply by tossing it in the air
and pushing the throttle joystick straight up. The 6-Axis Gyroscope technology allows the
drone to automatically stabilize, level itself out and hover smoothly while airborne.

FLIP STUNT MODE
ALTITUDE LOCK
HEADLESS MODE
AUTO RETURN
Have the drone hover at least 10 feet off the ground. Press the Flip
Stunt Button and push the right joystick in the direction you want the
drone to perform a single flip.
Pull the left joystick to the bottom left corner and the right joystick
to the bottom right corner to activate Altitude Lock. This makes the
drone keep its altitude without your input. Adjust throttle up or
down with the left joystick returning to the center to change current
altitude. Joystick will spring back to center after adjusting.
When flying you must know which direction your drone is facing to
control properly. Activate Headless Mode by pressing/clicking in on
the left joystick. The drones directional input on the right joystick
will now be mapped to your position so Up/Forward, Right/Right,
Left/Left, and Down/Backward. Normal function is returned by
pressing/clicking in on the left joystick again.
When you want to return the drone to you quickly and easily use
the Auto Return function. Fly the drone so that it is in front of you
and press/click in on the right joystick to start the function. While
returning you still control the throttle to safely land your drone.
IMPORTANT:
Make sure the drone is hovering at least 10 feet off the ground before
performing the flip stunt. The flip stunt will cause the drone to drop
approximately 6 feet. If you perform the flip stunt while being less than
10 feet off the ground, the drone could crash.

AUTOMATIC SHUTDOWN OVERRIDE FUNCTIONS
TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
Drone is unresponsive. The
Transmitter light keeps flashing.
Drone is unresponsive.
Transmitter light is ON. Drone is
unresponsive.
Drone’s rotors spins
but doesn’t take off.
Drone is shaking when flying.
Drone still moves forward after
adjusting the trim.
Drone moves while hovering
without transmitter input. Trim needs to be adjusted. Adjust the trim.
Gyroscope midpoint is off. Turn off both transmitter and drone.
Go through power on process and make
sure you place the drone on a flat
surface before taking off. Reset drone.
Transmitter batteries are
installed incorrectly.
Transmitter and or drone
is not powered ON.
Turn both transmitter and drone ON.
Transmitter batteries are drained.
Drone’s battery pack
is drained.
Rotor blades are damaged. Replace the damaged rotor blades.
Rotor blades are damaged. Replace the damaged rotor blades.
Drone is not on a
flat surface.
Place the drone on a flat surface
before attempting to take off.
Charge the drone’s battery pack.
Drone’s battery pack is drained. Charge the drone’s battery pack.
Install fresh batteries to the transmitter.
Install the batteries with the
correct polarity.
Transmitter is not syncing with
drone.
Repeat the power up process.
Website: www.worldtechtoys.com
Email: [email protected]
Phone: [phone]
Monday - Friday / 9:00AM - 5:00PM / Pacific Time
WWW.WORLDTECHTOYS.COM
MADE IN CHINA
SPECIFICATIONS,
COLORS AND CONTENT
MAY VARY FROM ILLUSTRATIONS
POST FLIGHT
After you are done flying the Drone make sure the battery pack on the drone is disconnected and
the transmitter power is turned off. If you are not going to use the drone for a long period of time,
please remove the AA batteries to prevent the batteries from draining or leaking.
For safety precautions, the drone will automatically shut down when the following situations occur:
1. When the drone’s battery is running low.
2. When one or more of the drone’s propellers gets into a collision impact or any form of
entanglement.