Worx WX156 Installation manual

物料号：２ＣＤＴ４５ＰＰＫ１１００５Ａ１
材料：１００克双胶纸
颜色：1色（黑）
尺寸：A5
页数：１２P
装订方式：骑马钉
备注：
特别提示：
此小页为说明书印刷要求，不需要输出菲林,
不作为印刷内容。

SAFETY AND OPERATING MANUAL
WX156 WX156.1
WX166 WX166.1 WX166.2
Lithium-Ion cordless
drill/driver

WX156 WX156.1
WX166 WX166.1 WX166.2
Lithium-Ion cordless
drill/driver
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING: Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for
future reference.
The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1. WORK AREA SAFETY
1) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
2) Do not operate power tools in
explosive atmospheres, such as in
the presence of flammable liquids,
gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3) Keep children and bystanders
away while operating a power tool.
Distractions can cause you to lose control.
2. ELECTRICAL SAFETY
1) Power tool plugs must match the
outlet. Never modify the plug in any
way. Do not use any adapter plugs
with earthed (grounded) power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
2) Avoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock
if your body is earthed or grounded.
3) Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric shock.
4) Do not abuse the cord. Never use
the cord for carrying, pulling or
unplugging the power tool. Keep cord
away from heat, oil, sharp edges or
moving parts. Damaged or entangled
cords increase the risk of electric shock.
5) When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of
electric shock.
6) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected
supply. Use of an RCD reduces the risk of
electric shock.
3. PERSONAL SAFETY
1) Stay alert, watch what you are
doing and use common sense when
operating a power tool. Do not use
a power tool while you are tired or
under the influence of drugs, alcohol
or medication. A moment of inattention
while operating power tools may result in
serious personal injury.
2) Use personal protective equipment.
Always wear eye protection.
Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions
will reduce personal injuries.
3) Prevent unintentional starting. Ensure
the switch is in the off-position
before connecting to power source
and/or battery pack, picking up or
carrying the tool. Carrying power
tools with your finger on the switch or
energising power tools that have the
switch on invites accidents.
4) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in
personal injury.
5) Do not overreach. Keep proper
footing and balance at all times.This
enables better control of the power tool in
unexpected situations.
6) Dress properly. Do not wear loose
clothing or jewellery. Keep your
hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
7) If devices are provided for the
connection of dust extraction and
collection facilities, ensure these are
connected and properly used. Use of
dust collection can reduce dust-related
hazards.

WX156 WX156.1
WX166 WX166.1 WX166.2
Lithium-Ion cordless
drill/driver
3
4. POWER TOOL USE AND CARE
1) Do not force the power tool. Use
the correct power tool for your
application. The correct power tool will
do the job better and safer at the rate for
which it was designed.
2) Do not use the power tool if the
switch does not turn it on and off.
Any power tool that cannot be controlled
with the switch is dangerous and must be
repaired.
3) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories,
or storing power tools. Such preventive
safety measures reduce the risk of starting
the power tool accidentally.
4) Store idle power tools out of the
reach of children and do not allow
persons unfamiliar with the power
tool or these instructions to operate
the power tool. Power tools are
dangerous in the hands of untrained
users.
5) Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool’s operation. If damaged,
have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
6) Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to bind
and are easier to control.
7) Use the power tool, accessories
and tool bits etc. in accordance
with these instructions, taking into
account the working conditions and
the work to be performed. Use of the
power tool for operations different from
those intended could result in a hazardous
situation.
5. BATTERY TOOL USE AND CARE
1) Recharge only with the charger
specified by the manufacturer. A
charger that is suitable for one type of
battery pack may create a risk of fire when
used with another battery pack.
2) Use power tools only with
specifically designated battery packs.
Use of any other battery packs may create
a risk of injury and fire.
3) When battery pack is not in use, keep
it away from other metal objects, like
paper clips, coins, keys, nails, screws
or other small metal objects, that can
make a connection from one terminal
to another. Shorting the battery terminals
together may cause burns or a fire.
4) Under abusive conditions, liquid
may be ejected from the battery;
avoid contact. If contact accidentally
occurs, flush with water. If liquid
contacts eyes, additionally seek
medical help. Liquid ejected from the
battery may cause irritation or burns.
6. SERVICE
1) Have your power tool serviced by
a qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
ADDITIONAL SAFETY
POINTS FOR YOUR
BATTERY OPERATED
DRILLS
1. Use auxiliary handle(s), if supplied
with the tool. Loss of control can cause
personal injury.
2. Hold power tool by insulated
gripping surfaces, when performing
an operation where the cutting
accessory may contact hidden
wiring. Cutting accessory contacting a
“live” wire may make exposed metal
parts of the power tool “live” and could
give the operator an electric shock.
SAFETY WARNINGS FOR
BATTERY PACK
a) Do not dismantle, open or shred cells or

WX156 WX156.1
WX166 WX166.1 WX166.2
Lithium-Ion cordless
drill/driver
4
battery pack.
b) Do not short-circuit a battery pack. Do
not store battery packs haphazardly in
a box or drawer where they may short-
circuit each other or be short-circuited by
conductive materials.
c) Do not expose battery pack to heat or fire.
Avoid storage in direct sunlight.
d) Do not subject battery pack to mechanical
shock.
e) In the event of battery leaking, do not
allow the liquid to come into contact
with the skin or eyes. If contact has
been made, wash the affected area with
copious amounts of water and seek
medical advice.
f) Seek medical advice immediately if a cell
or battery pack has been swallowed.
g) Keep battery pack clean and dry.
h) Wipe the battery pack terminals with a
clean dry cloth if they become dirty.
i) Battery pack needs to be charged before
use. Always refer to this instruction and
use the correct charging procedure.
j) Do not maintain battery pack on charge
when not in use.
k) After extended periods of storage, it may
be necessary to charge and discharge
the battery pack several times to obtain
maximum performance.
l) Battery pack gives its best performance
when it is operated at normal room
temperature (20°C ± 5°C).
m) When disposing of battery packs, keep
battery packs of different electrochemical
systems separate from each other.
n) Recharge only with the charger specified
by POSITEC. A charger that is suitable for
one type of battery pack may create a risk
of fire when used with another battery
pack.
o) When battery pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws or other
small metal objects, that can make a
connection from one terminal to another.
Shorting the battery terminals together
may cause burns or a fire.
p) Under abusive conditions, liquid may
be ejected from the battery pack; avoid
contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid
ejected from the battery may cause
irritation or burns.
q) Clean the battery pack contacts and also
those of the equipment prior to battery
installation.
r) Remove exhausted battery pack promptly.
s) Do not use any charger other than that
specifically provided for use with the
equipment.
t) Do not use any battery pack which is not
designed for use with the equipment.
u) Keep battery pack out of the reach of
children.
v) After extended periods of storage, it may
be necessary to charge and discharge
the battery pack several times to obtain
maximum performance.
w) Retain the original product literature for
future reference.
x) Remove the battery from the equipment
when not in use.
y) Dispose of properly.

WX156 WX156.1
WX166 WX166.1 WX166.2
Lithium-Ion cordless
drill/driver
5
To reduce the risk of injury, user
must read instruction manual
Warning
Wear ear protection
Wear eye protection
Wear dust mask
Indoor use only
Li-Ion battery.This product has been
marked with a symbol relating to
‘separate collection’ for all battery
packs and battery pack. It will
then be recycled or dismantled in
order to reduce the impact on the
environment. Battery packs can be
hazardous for the environment and
for human health since they contain
hazardous substances.
Do not burn
Batteries may enter water cycle if
disposed improperly, which can
be hazardous for ecosystem. Do
not dispose of waste batteries as
unsorted municipal waste.
C-Tick approval mark
SYMBOLS

WX156 WX156.1
WX166 WX166.1 WX166.2
Lithium-Ion cordless
drill/driver
6
1. KEYLESS CHUCK
2. TORQUE ADJUSTMENT RING
3. TWO-SPEED GEAR CONTROL
4. FORWARD/REVERSE ROTATION CONTROL
5. SOFT GRIP HANDLE
6. BATTERY PACK RELEASE BUTTON
7. BATTERY PACK *
8. SIGHT LIGHT
9. ON/OFF SWITCH
* Not all the accessories illustrated or described are included in standard delivery.
1
2
3
7
4
5
6
8
9

WX156 WX156.1
WX166 WX166.1 WX166.2
Lithium-Ion cordless
drill/driver
7
TECHNICAL DATA
WX156 WX156.1 WX166 WX166.1 WX166.2
Voltage 16V Max** 20V Max***
No load speed 0-400/0-1500/min
Number of clutch positions 15+1
Max torque 35N.m 40N.m
Chuck capacity 10mm
Max. drilling capacity
Steel 10mm
Wood 28mm 30mm
Machine weight 1.24kg 1.26kg
**Voltage measured without workload. Initial battery voltage reaches Maximum of 16volts.
Nominal voltage is 14.4volts.
***Voltage measured without workload. Initial battery voltage reaches Maximum of 20volts.
Nominal voltage is 18volts.
ACCESSORIES
We recommend that you purchase your accessories from the same store that sold you the
tool. Use good quality accessories marked with a well-known brand name. Choose the type
according to the work you intend to undertake. Refer to the accessory packaging for further
details. Store personnel can assist you and offer advice.
Model No. WX156 WX166 WX156.1 WX166.1 WX166.2
Li-Ion battery pack 1 1 2 2
30min Charger 1 1 1 1
Double ended bits 1 1 1 /
158pc Accessories / / / 1

WX156 WX156.1
WX166 WX166.1 WX166.2
Lithium-Ion cordless
drill/driver
8
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the instruction
book carefully.
INTENDED USE
The machine is intended for driving in and loosening
screws as well as for drilling in wood, metal and plastic.
BEFORE PUTTING INTO OPERATION
A) CHARGING THE BATTERY
The battery charger supplied is matched to the Li-Ion
battery installed in the machine. Do not use another
battery charger.
The Li-Ion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit:The tool
holder no longer rotates.
In a warm environment or after heavy use, the battery
pack may become too hot to permit charging. Allow
time for the battery to cool down before recharging.
When the battery pack is charged for the first time and
after prolonged storage, the battery pack will accept a
100% charge after several charge and discharge cycles.
B) TO REMOVE THE BATTERY PACK
(See Fig. A1)
Depress the Battery Pack Release Button(6) firmly first
and then slide the Battery Pack out from your tool.
C) TO INSTALL THE BATTERY PACK
(See Fig. A2)
Slide the fully charged Battery Pack onto the tool with
sufficient force until it clicks into position.
OPERATION
1. ON/OFF SWITCH (See Fig. B)
Depress the On/Off switch to start and release it to
stop your drill.The on/off switch is fitted with a brake
function which stops your chuck immediately when you
quickly release the switch.
It is also a variable speed switch that delivers higher
speed and torque with increased trigger pressure.
Speed is controlled by the amount of switch trigger
depression.
WARNING: Do not operate for long periods
at low speed because excess heat will be
produced internally.
A1
C1 F
A2
C2 G
E
B
D

WX156 WX156.1
WX166 WX166.1 WX166.2
Lithium-Ion cordless
drill/driver
9
2. SWITCH LOCK
The switch trigger can be locked in the OFF position.
This helps to reduce the possibility of accidental
starting when not in use.To lock the switch trigger,
place the rotation control in the center position.
3. REVERSIBLE (See Fig. C1, C2)
For drilling and screw driving use forward rotation
marked “ ” (lever is moved to the left). Only use
reverse rotation marked “ ” (lever is moved to the
right) to remove screws or release a jammed drill bit.
WARNING: Never change the direction of
rotation when the chuck is rotating, wait
until it has stopped!
4. TWO-SPEED GEAR CONTROL
(See Fig. D)
The drill has a two-speed gear control designed for
drilling or driving at LO (mark is 1) or HI (mark is 2)
speeds. A slide switch is located on top of the drill to
select either LO or HI speed. When using the drill in the
LO speed range, the speed will decrease and the drill
will have greater power and torque. When using the
drill in the HI speed range, the speed will increase and
the drill will have less power and torque.
Gear I
Low speed range: For screwdriving or working with
large drilling diameter.
Gear II
High speed range: For working with small drilling
diameter.
WARNING: To prevent gear damage, always
allow the chuck to come to a complete stop
before changing the direction of rotation or the
two-speed gear control.
5. CHUCK ADJUSTMENT (See Fig. E)
To open the chuck jaws rotate the front section of the
chuck. Insert the drill bit between the chuck jaws and
rotate the front section in the opposite direction. Ensure
the drill bit is in the center of the chuck jaws. Finally,
firmly rotate the front chuck section in the opposite
directions.Your drill bit is now clamped in the chuck.
6. TORQUE ADJUSTMENT (See Fig. F)
(Screw driving force of your drill driver)
The torque is adjusted by rotating the torque
adjustment ring.The torque is greater when the torque
adjustment ring is set on a higher setting.The torque is
less when the torque adjustment ring is set on a lower
setting.
A1
C1
F
A2
C2
G
E
B
D

WX156 WX156.1
WX166 WX166.1 WX166.2
Lithium-Ion cordless
drill/driver
10
Make the setting as follows:
1 - 4 For driving small screws
5 - 9 For driving screws into soft material
10 - 15 For driving screws into soft and hard
material
For heavy drilling
7. AUTOMATIC SPINDLE LOCK
(See Fig. G)
The automatic spindle lock allows you to use it as
a regular screwdriver.You can give an extra twist
to firmly tighten a screw, loosen a very tight screw
or continue working when the battery energy has
expired. For manual screwdriver purposes, the chuck is
automatically locked when the tool is off.
8. USING THE SIGHT LIGHT
To turn on the light simply press the on/off switch.
When you release the on/off switch, the light will be off.
LED lighting increases visibility-great for dark or
enclosed area. LED is also a battery capacity indicator. It
will flash when power gets low.
9. DRILLING
When drilling into a hard smooth surface, use a center
punch to mark the desired hole location.This will
prevent the drill bit from slipping off center as the hole
is started. Hold the tool firmly and place the tip of the
bit at the point to be drilled. Depress the switch trigger
to start the tool. Move the drill bit into the workpiece,
applying only enough pressure to keep the bit cutting.
Do not force or apply side pressure to elongate a hole.
Tungsten carbide drill bits should always be
used for concrete and masonry. When
drilling in metal, only use HSS drill bits in good
condition. Always use a magnetic bit holder (not
included) when using short screwdriver bits.
When screw-driving, apply a small quantity of
liquid soap or similar to the screw threads to
ease insertion.
10. DISPOSAL OF AN EXHAUSTED BATTERY
PACK
To preserve natural resources, please recycle or
dispose of the battery pack properly.This battery
pack contains Lithium batteries. Consult your
local waste authority for information regarding
available recycling and/or disposal options. Discharge
A1 C1
F
A2 C2
G
E
B D

WX156 WX156.1
WX166 WX166.1 WX166.2
Lithium-Ion cordless
drill/driver
11
your battery pack by operating your drill, then
remove the battery pack from the drill housing
and cover the battery pack connections with
heavy-duty adhesive tape to prevent short
circuit and energy discharge. Do not attempt
to open or remove any of the components.
11. OVERLOAD PROTECTION
When overloaded, the motor comes to a stop.
Relieve the load on the machine immediately
and allow cooling for approx. 30 seconds at
the highest no-load speed.
12. TEMPERATURE DEPENDENT
OVERLOAD PROTECTION
When using as intended for the power tool
cannot be subject to overload. When the
load is too high or the allowable battery
temperature of 75°C is exceeded, the
electronic control switches off the power
tool until the temperature is in the optimum
temperature range again.
13. PROTECTION AGAINST DEEP
DISCHARGING
The Li-Ion battery is protected against deep
discharging by the “Discharging Protection
System” . When the battery is empty,
the machine is switched off by means of a
protective circuit:The inserted tool no longer
rotates.
PROBLEM SOLUTION
1. WHY DOES THE DRILL NOT TURN ON
WHEN YOU PRESS THE SWITCH?
The forward/reverse rotation control, which is
on top of the trigger, is positioned in the lock
function. Unlock the forward/reverse rotation
control by putting it into the required rotation
position. Push the trigger and the drill will
start to rotate.
2. THE DRILL STOPS BEFORE THE
SCREW IS COMPLETELY TIGHTENED.
WHY?
Verify the torque position of the torque
adjusting ring, you can find the torque-
adjusting ring between the chuck and the drill
body. Position 1 is the lowest torque (screw
driving force) and position 15 is the highest
torque (screw driving force). Position is for
drill operation. Regulate the torque adjusting
ring to a higher position to reach the best
result.
3. REASONS FOR DIFFERENT BATTERY
PACK WORKING TIMES
Charging time problems, as above, and
having not used a battery pack for a prolonged
time will reduce the battery pack working time.
This can be corrected after several charge and
discharge operations by charging & working
with your drill. Heavy working conditions such
as large screws into hard wood will use up the
battery pack energy faster than lighter working
conditions. Do not re-charge your battery pack
below 0OC and above 45OC as this will affect
performance.
MAINTENANCE
Your tool requires no additional lubrication or
maintenance.
There are no user serviceable parts in your
power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power tool
in a dry place. Keep the motor ventilation slots
clean. Keep all working controls free of dust.
Occasionally you may see sparks through the
ventilation slots.This is normal and will not
damage your power tool.

Copyright © 2013, Positec. All Rights Reserved.
2CDT45PPK11005A1