Wow SparkMaker User manual

Operating Guide
Please read this entire guide before beginning
Copyright © 2018 WOW Innovation(ShenZhen) Teth Co.Ltd Copyright

3
Precautions for using the printer：
•Do not eat the resin used for printing and the printed model.
•Keep the resin out of reach of children and pets.
•Try to avoid contact between the resin and the skin. Wear gloves when operating.
•Shake the resin evenly before use.
•The resin should be stored in a cool,backlit place.
•When the resin is accidentally splashed on the eyes or skin,it should be washed with soapy water in
time. If you feel unwell,please consult a doctor promptly.
•The printer should be placed in a place where there is no direct sunlight.
•The UV cover should be covered when printing.
•Avoid looking directly at the UV lamp,and if need please wear goggles.
•Do not spill resin on the working panel.
•Children under the age of 18 should be operated under the supervision of an adult.
•Use printers in strict compliance with local laws and regulations.
•Do not disassemble the printer while it is powered on to avoid danger,and disassembling the printer
without permission will void the warranty.
Please keep your instruction manual in a safe place
Always with the basic defensive measures when using the printer to reduce the
risk of injury such as fire and electric shock, including the following measures：
•Read all instructions before using the printer.
•Do not submerge or expose printer components to water or cleaning solutions.
•To prevent electric shock,do not put the device,power adapter,or plug into water or other liquids.
•Do not place or store the unit where it can be easily dropped or easily pulled into the tub or basin.
•The printer shouldn't be used outdoors,for indoor use only.
•When removing the plug from the electrical outlet,do not pull on the power adapter.
•When pulling out the plug,grasp the plug,not the power cord.
•Do not use non-vendor original accessories or accessories,they may cause re,electric shoc,injury.
•Do not operate the device if the device power adapter or plug fails or is damaged.
•Do not directly touch liquid resin and the printed model of residual liquid resin on surface. Some people
may be allergic to the resin and have different degrees of allergic reactions. At this time,wash with
soapy water and seek medical advice promptly.
•This SLA 3D printer,its photosensitive resin material,printed resin model and packaging materials are
not toys. Please keep away from children and pets to avoid suffocation,re,serious allergies,etc. caused
by ingestion.
•Do not use this product for any other purpose.This product is only suitable for SLA 3D printing,and all
equipment parts are only used for UV light curing 3D printing. This device may not be used to create
models that violate local laws and any illegal modications. Unintended use of this product may result in
violation of local laws.
2
Important safety notice
Important safety notice

©This is a desktop-grade SLA light-cured 3D printer that delivers high-quality,SLA 3D printer experience
when the power supply is working properly and components are not damaged.
©Read the entire user manual and become familiar with the features of the product before proceeding.
Failure to operate this product properly may result in serious injury to yourself or others,or damage to the
product or property damage. This product is a little complex and requires a period of familiarity before it
can be used safely and requires some expertise to operate. Without a strong sense of safety,improper
practices can result in product damage and property damage,and can even cause serious harm to others.
This product is not suitable for children. Do not use parts that are not provided or recommended by
WOW,and must be installed and used in strict accordance with wow guidelines. This guidance document
contains instructions for safety, operation,and maintenance. Be sure to visit the SparkMaker website
(https://www.sparkmaker3d.com/) to download the user manual and read all instructions and warnings
in the documentation before use.
4
©Please read this document carefully before using the product to understand your legal
rights,responsibilities and safety instructions; otherwise it may cause property damage,safety accidents
and personal safety hazards. By using this product,you are deemed to have understood,endorsed and
accepted all the terms and contents of this document. The user is committed to being responsible for his
or her actions and all consequences arising therefrom. The user undertakes to use the product only for
legitimate purposes and agrees to all terms and content of this document and any relevant policies or
guidelines that may be customized by WOW Innovations (Shenzhen) Technology Co.,Ltd.
©WOW Innovation (Shenzhen) Technology Co.,Ltd. reserves the right to update this Disclaimer and
Warning. WOW Innovation (Shenzhen) Technology Co.,Ltd. does not assume any loss caused by the
user not using the product in this User Manual. In compliance with laws and regulations,WOW Innovation
(Shenzhen) Technology Co., Ltd. has the nal right to interpret this document. WOW Innovation (Shenzhen)
Technology Co.,Ltd. reserves the right to update,change or terminate these Terms without prior notice.
5
Disclaimer and warning
Disclaimer and warning

8
10
Component
Check after unpacking
11 Product working principle
12 Specifications of SparkMaker
15 Resin
17 Color paste
18 Important definition
23
24 Quick start guide
25 Power connection
31
Leveling the printing platform
27
Start printing
Check before printing
36
End printing
Adjustment of the printer
Recycling of resin & Tank cleaning
Replace the FEP lm
Replace the LCD screen
Replace the light board
Adjustment of the Z axis
Filtration residue
Add support
FAQ
Basic operational concept
Terms & Conditions
Customer service
43
44
49
55
68
78
110
113
114
91
88
7
100
6
Cotton Cotton
Specifications of SparkMaker FHD
13

Component
SparkMaker3D printer Power adapter Power cable
Operation guide
Small hex wrench
Big hex wrench
89
Please take the time to familiarize yourself with the
items in the package. You should receive the illustrated
component.
To make your products safer to use,WOW provides users with detailed operating
instructions.
Users are advised to check the documentation and components according to the
component list. If you nd any missing or item is not perfect,please contact WOW or
the merchant who sold the product. Please read this document carefully,watch the
instructional video,use the quick start guide to understand the use method,before
printing.
The user manual must be read carefully. Please be sure that you are familiar with the
functions of the various components of this product before using this product.
And learn the basics about 3D printing. If you have any questions about using this
product,please contact a WOW or WOW authorized dealer.
Component
Component

Check after unpacking
Open the package to confirm that the components are integrity, then
check the printer's functions to ensure that it works properly.
❶Test power function:Connect the power supply. After the printer is powered on,confirm that if
the indicator of the knob is working properly ，and the indicator of the knob will display the Light blue
lightlight if it working properly .
❷Test knob function and Z-axis motion:Rotate the knob to confirm whether it can control the
printing platform move up and down,and whether the knob rotates smoothly.
❸Test photoelectric switch:Remove the printing platform and continue to rotate the knob clockwise
to control the lifting cantilever to descend until the trigger piece on the lifting cantilever is inserted into
the photoelectric switch groove to trigger it to conrm whether the lifting cantilever stops.
❹Test print function:Remove the printing platform,download the print file "print.wow"for
SparkMaker versionor "print.fhd"for SparkMaker FHD versionfrom SparkMaker official
website www.sparkmaker 3 d.comand save it to the SD card. Insert the SD card with the print le into
the printer card slot and the indicator of the knob will become the green breathing light,then press
the knob to start printing. At this time,the indicator light changes from green to red and flashes,the
lifting cantilever will drop to the position of the trigger photoelectric switch,then the light board will,emit
ultraviolet light,the fan will start to work,the screen will display the bottom layer pattern,and wait for a
bottom exposure time. After that,the light board is extinguished,the lifting cantilever will rise a certain
distance,and then decline again,then the light board emit ultraviolet light,and the screen displays the
next pattern... Continue this process until the end of printing.
❺Test tank:Check if the FEP membrane at the bottom of the tank has obvious scratches or broken
holes. Pour some water into the tank to check if it will leak.
10
Product working principle
SparkMaker SLA 3D printer
Designing a 3D solid model through 3D software,slice the model with SparkStudio,the
generated data will be used to accurately control the switch of the light board and the
movement of the lifting platform through the main board. The light beam emitted by the light
board passes through the controllable liquid crystal screen and is irradiated onto the surface
of the liquid photosensitive resin according to the designed path. Curing a layer of resin in a
specic area of the surface. When this layer is processed,a section of the model is generated.
The lifting platform is raised by a certain distance,the solid layer is covered with another layer
of liquid resin,and then the second layer is scanned,and the second solidified layer is firmly
bonded to the previous solidified layer,so that the layers are superposed to form a three-
dimensional model. After the model is taken out of the resin,clean the resin on the surface
of the model with alcohol,and the nal curing,and then polished,painted or colored to get the
desired product.
11
Check after unpacking
Product working principle

Specification of the SparkMaker
Molding size 98mm*55mm*125mm
XY-axis direction accuracy 100μm
Z-axis direction accuracy 25-100μm
Print material Photosensitive resin
Single layer printing time 8-15 S
Printing method SD card offline printing
Print le format *.wow
Printer control Knob
Curing ultraviolet light 400-410nm 24W UV LED
Operating software SparkStudio
Stepper motor drive 128 microsteps
Physical dimension Φ170mm*284mm
Total weight 2.2KG
Input power DC 24V 2A 48W
12
Specication of the SparkMaker
Specification of the SparkMaker FHD
Molding size 110mm*61.8mm*125mm
XY-axis direction accuracy 100μm
Z-axis direction accuracy 25-100μm
Print material Photosensitive resin
Single layer printing time 3-12 S
Printing method SD card offline printing
Print le format *.fhd
Printer control Knob&APP
Curing ultraviolet light 400-405nm 84W UV LED
Operating software SparkStudio
Stepper motor drive 128 microsteps
Physical dimension Φ170mm*288mm
Total weight 2.2KG
Input power DC 24V 4A 96W
13
Specication of the SparkMaker FHD

14
Platform handle
Printing platform
Knob
Cover
Resin tank
Card slot
Specication of the SparkMaker
Resin
Type Feature Color Hardness Elongation Description
LCD-T Tough Clear 60D 115% ABS Alike
LCD-W Water
Washable Clear 60A 150% Water Washable
LCD-C Casting Clear 80A 24% Casting
LCD-E Elastic Clear 26A 300% Rubber Alike
LCD-N Nylon Alike Black 75D 115% Nylon Alike
LCD-H High HDT Clear 90D 3% >300℃HDT
LCD-G Super Clear Clear 70D 5% Super Clear
LCD-Q easy dyeing light yellow 80D 5% colorful paste
LCD-MG Rigid&Tough gray 80D 5% Rigid&Tough
LCD-BG
Hard
Gray
75D 3% Rigid
LCD-BW White
LCD-BF Flesh
15
Resin

Precautions for resin use:
❶Theoretically,resins with a curing band of 400-410 nm can be used in SparkMaker,but if
other third-party resins are used,the printed parameters must be adjusted by yourself.
❷SparkMaker's resin can also be used on other SLA 3D printer use PTFE lm or FEP lm as tank
bottom,and the curing band is on 355-420nm SLA 3D printer,but the actual printing parameters
need to be adjusted by users.
❸Damage to parts caused by the use of third-party resins will invalidate the warranty.
❹The color paste addition ratio should be less than 1%,and the resin exposure time should be
increased appropriately after adding the color paste.
❺ The resin after adding the color paste should be evenly mixed to prevent the color paste from
precipitating.
❻Do not mix a variety of different types of resins,and it will cause the resin properties and
printing parameters change greatly,making it difcult to print.
❼The photosensitive resin will react with some plastics such as ABS,PC,etc. Do not drop the
resin on such plastics.
❽Use of third-party color paste or other dyes may result in printing failure or damage to the
printer.
❾Should choose the right resin according to different needs.
❿For models with small features and high precision requirements,deep color and high hardness
photosensitive resins should be used.
⓫If photosensitive resin with low hardness,high toughness and softness,which may have
different degrees of deformation during printing.
16
Resin
Color paste
Color principle：
CMYK is the four-color printing mode used for color printing.
Based on the principle of trichromatic mixing，with black ink,a total of four colors are
mixed and superimposed to form a "full-color printing".
The four standard colors are：
C=Cyan M=Magenta Y=Yellow K=key
Here K refers to the Key,it can also represent Black,because printing is more often
used in black. In addition,we also added a white color paste.
C+M=Purple
M+Y=Orange
C+Y=Green
Method of operation：Pour the resin into a cup rst,then add a drop of color
paste to the cup,stir evenly,nally pour the resin of the mixed color paste into
the trough and print.
Notice:
Adding a white color paste will make the color soft.
Adding black paste will make the color dignied.
Users can adjust different doses and ratios to call up richer colors.
The color paste addition ratio should be less than 1%,and the resin exposure time
should be appropriately increased after adding the color paste.
The resin after adding the color paste should be stirred evenly to prevent the color
paste from being precipitated. 17
Color paste

Important Definition
Cover: Protective cover to prevent external light and dust from affecting the resin in the tank.
Notice:
❶Do not drop the resin on the cover. If it is accidentally dropped on it please clean it in time.
❷Do not put heavy objects on the cover to avoid crushing the cover.
Tank: The container for storing resin during printing.
FEP film: Located at the bottom of the tank for release demolding during printing,UV light can pass through it to
cure resin.
Notice:
❶The FEP lm at the bottom of the tank is easily damaged. Do not scratch it with a sharp object.
❷After removing the tank,use a paper towel pad on the bottom of the tank to avoid damage to the FEP lm.
❸Please clean the resin that has accidentally dropped on the outer wall of the tank and the screw hole to avoid
damage to the LCD screen.
❹When installing the tank,please make sure that the FEP lm is close to the LCD screen to avoid affecting print.
❺Less than 240ml resin should be poured into the tank. Do not pour in too much resin,it will result in resin
overow damage to the LCD screen.
Printing platform: Parts for leveling and xing aluminum plate.
Plate: Aluminum alloy plate for sticking the model on the printing platform.
Notice:
❶Make sure the print platform is fully inserted under the platform handle.
❷Make sure the print platform is correctly leveled before printing to avoid damage to the LCD screen.
❸When leveling,please cross lock four screws while pressing down the aluminum plate.
❹Do not scratch too deep under the aluminum plate,but slight scratches do not affect printing.
Platform handle: Fix the platform on the Z axis to prevent it from moving.
Notice:
18
Important Definition
❶Tighten the platform handle before printing to prevent it from sliding during printing.
❷Please clean the resin residue on the handle of the platform in time.
Knob: Knob operation and indicator light:
1. Control motor: In the uninsert SD card state,the indicator light is light blue.When the knob rotates clockwise,the
platform descends; when it rotates counterclockwise,the platform rises.
2. Printing: Insert the SD card,the indicator light will become green breathing light,press the knob to start printing,the
indicator light turns into red and ashing,and the printer enters the printing state.
3. Stop: In printing mode,long press the knob,the indicator will turn blue and eventually turn green,which is to
terminate printing.
4. Pause:In printing mode,press the knob and the indicator will turn blue.After the current print layer is cured,the print
platform will lift 30mm and the printer will pause printing.
5. Continue: After the printing platform lifted by 30mm and pause printing,press the knob,the printing platform will
descend and continue printing,and the indicator light will turn red and ashing.
6. If there is no print le in the SD card or the SD card is not recognized,after pressing the knob,it will change from
green to red and quickly turn to green again.
Notice:
❶Do not drop the resin on the knob.If it drops accidentally,please clean it in time.
❷Do not over-tighten the two screws above the knob.
SD card:The carrier for storing print les.
SD card sort:Used to read SD card data.
Notice:
❶When inserting,the metal contact point of the SD card is facing up,please do not insert the opposite.
❷Multiple of print les can be stored in the SD card,but when you use the knob to control the printer to print,the
printer can only recognize the print file named "print.wow"for SparkMaker versionor "print.fhd" for
SparkMaker FHD versionand print it. Users can name the files that do not print as other names,and name the
file to be printed as"print.wow"(for SparkMaker version)or "print.fhd"for SparkMaker FHD version,if
you want to change the print file,you can directly modify the file name. If you use APP to control printing,on the
APP,you can directly select the file you want to print . 19
Important Definition

❸Please use SDHC (Secure Digital High Capacity) with a maximum capacity lower than 32GB.
Adapter: Used to convert 110V-240V AC to 24V DC to provide power to the printer.
DC socket: Located at the right rear of the printer,is the power socket to connect the printer and the
adapter.
Notice:
❶Do not use a non-original power adapter to avoid danger.
❷Please plug in the print DC socket before powering on the adapter. Do not plug in the DC socket after the
adapter is powered.
Light board: Provide UV light to cure the liquid resin in the tank.
Notice:
❶Do not look directly at the UV light emitting from the light board. Wear goggles if do it.
❷Please ensure that the fan works normally when the light board is working to avoid damage to the
machine caused by excessive temperature.
Shading tape:Used to block the unrequired UV light around the LCD screen.
LCD screen:Used to display the section pattern of the printed model and cooperate with the UV light to cure the
resin.
Notice:
❶The LCD screen is extremely fragile,please be careful.
❷If the tank leaks out and causes the resin to ow out and cured on the LCD screen,please carefully remove the
cured resin residue before the next printing.
❸Make sure that there are no resin residues on the LCD screen to block UV light.
❹If the print failed,please clean the residual resin in the tank and aluminum plate in time to avoid crushing the
LCD screen when printing next time.
❺Make sure the printing platform is properly leveled when printing,so as to avoid damage to the LCD screen.
❻Please ensure that the FEP lm is close to the LCD screen to avoid affecting the print quality.
❼Make sure that the black tape completely block the unrequired UV light around the LCD screen.
Screw motor:Used to drive the lifting cantilever move up and down.
20
Important Definition
Copper nut:For working with screw motors.
Guide rail:For linear motion guidance.
lifting cantilever:Motor and guide rail control its up and down during printing.
Notice:
❶Do not block the rotation of the screw motor.
❷Do not over-tighten the mounting screws of the copper nut.
❸Do not drop resin and other debris on the guide rail and the screw that interfere with its work.
❹Please add grease to the screw,copper nut and guide rail in time to avoid excessive abrasion.
❺Do not drop the resin on the bafe. If it is accidentally dropped,please clean it in time.
Photosensitive resin: Liquid light curing resin for printer use.
Notice:
❶Do not touch the skin directly with the resin. Wear gloves when handling. If skin contact occurs,wash
it with soapy water. If you feel unwell,please consult a doctor.
❷The resin remaining after printing,if it would not be used for a long time,please keep it in cool and dark place.
❸Shake the resin evenly before use.
❹Do not eat the printed model and the resin used for printing.
❺Keep the resin out of reach of children and pets.
❻Do not drop the resin on any parts other than the tank and aluminum plate.If it is dropped,please clean it in
time.
❼Use of third-party color paste or other dyes may result in printing failure or damage to the printer.
Working panel:Panel for mounting components such as LCD screens and tank.
Hexagonal wrench:Big hex wrench and small hex wrench for hex screws.
Trigger piece:Used to trigger photoelectric switch.
Photoelectric switch:Used to determine if the platform has reached the lowest point.
Notice:
❶Do not block the photoelectric switch,otherwise the photoelectric switch will not be triggered. 21
Important Definition

❷When leveling,please ensure that the trigger piece is inserted into the photoelectric switch groove.
❸Do not drop the resin on the working panel and photoelectric switch.
Fan:Cooling the control system and the light board.
Notice:
❶Make sure that the cooling fan is working properly and avoid system failure due to excessive temperature.
❷Please make sure not to block the air outlet and air inlet.
LCD screen FPC cable:Connecting the mainboard to the LCD screen.
Alcohol: A cleaning agent used to clean printed models.
Note:
1.Please use alcohol with a concentration higher than 95%.
2.Do not soak the model in alcohol for too long.
3.Please use alcohol carefully to avoid safety risks.
UV curing lamp: used to solidify the newly printed model so that it is completely solidied.
Note:
1.Please use a curing lamp with a band of 395-420nm and a power of more than 10W.
2.When curing the model with curing lamp,the model can be placed in glycerin to prevent the deformation of the
model due to temperature and other factors in the curing process.
3.Too long post-curing time will lead to shrinkage and yellowing of the model,and too short post-curing time will
lead to the incomplete curing model of the model is soft.
22
Important Definition
23
Check before printing
❶Keep the power connection stable.
❷Knob rotates smoothly and presses smoothly.
❸Z-axis movement is smooth and unobstructed.
❹There is no resin residue on the aluminum plate of the printing platform.
❺The handle on the print platform has been tightened.
❻The print platform has been correctly leveled.
❼The tank is installed correctly,and the FEP lm at the bottom of the tank is close to the LCD screen.
❽No resin residue in the tank and on the FEP lm.
❾No residual resin on the outer wall of the tank,the bottom of the tank,the LCD screen and the working
panel.
❿The resin poured into the tank is less than 240ml. If the model is large,the resin can be added during
the printing process.
⓫Printed model files have no fault and are not damaged.
⓬Ensure the model's the position of the long-span cantileve,the lowest point of the layer and the position
that needs to be strengthened,add with the right size of support and the right amount of support,and the
right bottom valve.
⓭The slice parameters such as the layer thickness,exposure time,and lifting speed of the print file are set
correctly.
⓮The slice file is completely saved in the SD card,the bottom surface of the model is completely attached
to the lowest point of the printer,and there is no fault on the print model file
⓯If you use the knob to control the printer to print,you need to name the print file as"print.wow"for
SparkMaker version)or "print.fhd" for SparkMaker FHD version,and save it to the SD card.
⓰The SD card is a C10 high-speed card with a capacity lower than 32GB. The file system format is
FAT32. The SD card is completely unlocked by hardware. The metal contacts are intact and free of stains.
⓱When the card slot is inserted,the SD card metal contact point is inserted face up into the machine card
slot and is in fully contact with it.
Check before printing

Quick start guide
Power cord connection
Adapter
Power cord
Socket
Power cord socket
DC input
Switch
Plug the power cord socket
into the adapter interface
first,and plug the power
cord into the socket.
Plug the adapter plug into the
DC input on the back of the
printer,then press the switch on
the cable to start the printer.
25
Power cord connection

Leveling the printing platform
Use the big hex wrench to loosen the four screws on both sides of
the platform counterclockwise so that the aluminum plate can move
up and down freely.
27
Big hex wrench Handle
Big hex wrench
Aluminum plate
＊Notice:
❶Do not unscrew the screw completely.
❷Make sure the handle is fully tightened.
❸Please ensure that there are no residual resin
or obstacle on the aluminum plate and the tank
to affect the leveling.
❹Make sure the tank is installed correctly.
Leveling the printing platform

28
Rotate the knob clockwise
to lower the platform to the
lowest point of the tank,that the
platform can no longer move
down meanwhile trigger piece
trigger the photoelectric switch.
＊Notice:
When the photoelectric switch is triggered,the
trigger piece should be inserted into the
middle notch.
Trigger piece
Photoelectric switch
Leveling the printing platform
29
Use two fingers to press down on each side of the aluminum plate,and
press it close to the FEP film,meanwhile use the big hex wrench to tighten
the four screws clockwise to fix the aluminum plate.
Big hex wrench
Aluminum plate
＊Notice:
Please stagger tighten the four screws
to make the aluminum plate and the FEP
film close enough,so as to prevent the
aluminum plate from lifting up on one side
and causing the leveling to fail.
Big hex wrench
Hand
Leveling the printing platform

Start printing
31
Insert the SD card into the computer,open the SparkStudio
software,import the *.stl file of the model into the SparkStudio
software,adjust the appropriate angle,add the appropriate support,set
the correct print parameters,save the slice file *.wow(for SparkMaker
version)or *.fhd (for SparkMaker FHD version)in the SD card after
slicing,and then remove the SD card from PC.
＊Notice:
❶See below for methods and rules for
adding supports and for setting print
parameters.
❷If you use the knob to control the
printer to print,the print file must be
named as "print.wow"(for SparkMaker
version)or "print.fhd" (for SparkMaker
FHD version)
Computer
SD card
Start printing

32
Card slot
SD card
Insert the SD card into the
card slot under the printer.
＊Notice:
When inserting,the metal contact
point of the SD card is facing
up,please do not insert the opposite
to avoid damage to the card slot.
Start printing
33
Open resin bottle and pour the appropriate resin (less than 240ml) into the
tank according to the size of the model.
＊Notice:
❶Please do not pour in excess
resin to prevent resin from
overflowing,resulting in damage to
the LCD screen.
❷Please do not drop the resin on
the screw hole of the tank,the outer
wall of the tank and the working
panel,resulting in damage to the
LCD screen. If it accidentally flows
in,please clean it in time.
❸Resin remaining in the resin
bottle,should be sealed in a dark
shade away from children and pets.
❹If not used for a long time,please
pour the resin into the storage
container. Do not place the resin in
the tank for more than two weeks.
❺Please ensure that there are no
residual resin or obstacle on the
aluminum plate and the tank to avoid
damage to the LCD screen.
Resin
Resin bottle
Start printing

34
(As shown)Cover the printer with the
cover,press the knob,the indicator will
turn red and flashing,and the printer will
start printing.
＊Notice:
❶Do not place the printer in a location exposed to strong
light,including but not limited to windows,under the table
lamp,and outdoors.
❷Avoid looking directly at the UV lamp. If you need to
see it,please wear goggles.
Knob
Hand
Cover
Start printing
End of printing

36
The knob indicator
changes from a flashing
red light to a green
breathing light,it means
the end of printing.
Remove the cover from
the printer
Model
Cover
End of printing
37
After loosening the platform handle
counterclockwise,pull the platform
forward and remove it.
＊Notice:
❶Do not completely unscrew the handle.
❷Do not touch the printed model directly to
avoid resin contact with the skin.
❸When removing the platform,do not
drop the resin on the outer wall of the
tank,the mounting screw holes,the working
panel,the outer casing and the cover,and the
installation clearance.
❹Be careful to avoid model damage when
removing the platform.
Handle
Platform
Model
End of printing