X-Stand MAX XL Quick guide

MAX XL
© 2019 X-Stand™ TREESTANDS. All right reserved.
This X-Stand™ product(s) has been tested to rigid industry standards. Safe operation and use of
this X-Stand™ product(s) is the responsibility of the user(s). Please read and follow all safe use
instructions and warnings. Failure to follow these may result in serious injury or death!
First Edition, February 2019, Published by X-Stand™ TREESTANDS, Lakeville, Minnesota.

READ THIS MANUAL IN ITS ENTIRETY PRIOR RO USING THIS PRODUCT.
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
2
Max. Weight Capacity (User(s) and Equipment) 300 lbs (136 kg)
XSLS569 • MAX XL
LADDERSTAND SAFE USAGE INSTRUCTIONS & WARNINGS
WARNING!
limitations include the user(s) and their equipment. DO NOT use these product(s) if you
This product carries strict weight restrictions. Please note that these weight
exceed these total weight limitations. Failure to follow these instructions may result in
serious injury or death!
A safe treestand hunting video, Treestand Safety: It’s Up To You,has been included.
Please view it in its entirety prior to using this product! Thank you for your purchase of this
quality X-Stand™ Treestands product. To ensure your personal safety, please take a mo-
ment to carefully read this Instruction Manual in its entirety before attempting to assemble,
set-up, install and/or otherwise use this X-Stand™ Treestands product. Failure to follow
these instructions may result in serious injury or death!
Should you have any questions about the installation and/or use of this product, or any
other X-Stand™ Treestands product(s) do not hesitate to call one of our customer service
representatives at 540-877-2769 or visit X-Stand™ Treestands online at X-Stand.com.
Our customer service representatives will answer any questions you may have about any
of the complete line of X-Stand™ Treestands products.
Do not return this product to the retailer if you have any damaged or missing parts. Call X-
Stand™ Treestands for replacement of any damaged or missing parts at 540-877-2769.
WARNING!
Failure to read and strictly comply with the instructions contained in this
Instruction Manual may result in serious injury or death!
WARNING!
FALLS FROM A TREESTAND CAN OCCUR ANYTIME AFTER LEAVING THE
GROUND. THESE FALLS COULD RESULT IN EITHER SERIOUS INJURY OR DEATH! FOR YOUR
PERSONAL SAFETY, PLEASE TAKE A MOMENT TO CAREFULLY READ THIS PRODUCT
INSTRUCTION MANUAL IN ITS ENTIRETY BEFORE ATTEMPTING TO ASSEMBLE, SET-UP,
INSTALL AND/OR OTHERWISE USE THIS X-STAND™ PRODUCT. AT LEAST ANNUALLY,
REVIEW THE CONTENTS OF THIS INSTRUCTION MANUAL AND WATCH THE SAFE TREESTAND
HUNTING DVD. ADDITIONALLY, KEEP THESE INSTRUCTIONS FOR THE ENTIRE DURATION
THAT YOU OWN THIS PRODUCT(S). FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT
IN SERIOUS INJURY OR DEATH!
WARNING!
A Treestand Safety: It’s Up To You DVD has been included with this
treestand. Please view it in its entirety prior to using this or any other X-Stand™ product(s).
Failure to follow these instructions may result in serious injury or death!
WARNING! THE SAFE USE AND OPERATION OF THIS PRODUCT IS THE SOLERESPONSI-
BILITY OF THE USER. IT IS ALSO THE SOLE RESPONSIBILITY OF THE OWNER TO PROVIDE
ANY PERSON(S) WHO BORROW OR PURCHASE THIS PRODUCT WITH THESE INSTRUCTIONS
AND THE AFORE MENTIONED TREESTAND SAFETY: IT’S UP TO YOU DVD. FAILURE
TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH! ADDITIO-
NALLY, FAILURE TO FOLLOW THIS INSTRUCTION MAY SUBJECT YOU TO PERSONAL LIABILITY
PENALTIES AS DETERMINED BY THE U.S. JUDICIAL SYSTEM.
WARNING!
Prior to each hunt, you must inform someone of your hunting location,
to follow these instructions may result in serious injury or death!
including the specific location of your treestand and the expected duration of your hunt. Failure
WARNING! Prior to each hunt, make sure that you have a signaling device (e.g., mobile
and in an operable condition. This device must be within easy access should you exper-
phone, radio, whistle, signal flare or Personal Locator Device (PLD)) in your possession
ience the need to contact emergency assistance. Failure to follow these instructions may
result in serious injury or death!
WARNING!
DO NOT remove, modify, and/or omit any portion or otherwise mechanically
modify this X-Stand™ product(s) or its assemblies in any manner. Modification, misuse,
and/or part substitution shall immediately void your factory warranty and may result in
serious injury or death! If you suspect that a part(s) is missing and/or defective, immedi-
ately contact X-Stand™ at 540-877-2769 for replacement of missing or defective parts.
Never modify your stand in any way by making repairs, or altering, adding or attaching
anything to it except if explicitly authorized in writing by X-Stand™. ALWAYS USE GENUINE
FACTORY AUTHORIZED X-STAND™ REPLACEMENT PARTS. USE OF ANY REPLACEMENT
PARTS OTHER THAN GENUINE X-STAND™ PARTS VOIDS YOUR WARRANTY AND MAY
RESULT IN SERIOUS INJURY OR DEATH!
WARNING!
ALWAYS inspect/check ALL expiration dates/tags on all straps and the full-
body fall arrest harness and its components prior to each use. You must replace ALL straps
and suspension seats EVERY year. Never use any strap(s) or full-body fall arrest harness
or its components that has expired and/or is showing any signs of damage and/or wear.
Failure to follow these instructions may result in serious injury or death!
WARNING!
Make certain all chains, cables, straps, etc. are tightened per this Instruction
Manual prior to use. All treestand contact points must be in contact with the tree before
you step onto the stand. The correct adjustment and tightening of attachment hardware is
critical to the stable installation of this treestand. Additionally, you MUST be wearing your
Fall Arrest System (FAS) which includes a full-body fall arrest harness, tree belt, lanyard/
tether, suspension relief device and climbing belt/lineman’s belt (as applicable) in accord-
ance with the Instructions contained in this Instruction Manual. Failure to follow these
instructions may result in serious injury or death!
WARNING!
This product(s) is designed for adult use only. No one under the age of 16
should attempt to use this or any other X-Stand™ product(s) without direct adult super-
vision. Failure to follow these instructions may result in serious injury or death!
WARNING!
Prior to attempting to use this or any other X-Stand™ product(s) you must
take a moment and become familiar with its assembly, setup and installation. You must
practice installing, setting-up and using your full-body fall arrest harness and its compo-
nents (i.e., lanyard/tether, tree belt, suspension relief device, climbing belt/lineman’s belt
[as applicable]) at ground-level prior to attempting to use it at heights above ground-level.
Once you have become thoroughly knowledgeable and comfortable with this X-Stand™
product(s) setup, installation and use at ground-level, you are now ready to use it at heights
above ground-level. Failure to follow these instructions may result in serious injury or
death!
WARNING!
Several X-Stand™ Treestands are equipped with a footrest, armrests and/
or shooting rail. Neither the footrest, armrests nor the shooting rail have been designed to
support the users weight. Under no circumstances should you place any more than fifteen
(15) lbs (6 kg) of weight on these structures. Doing so will put the user in serious risk of
injury or death. Failure to follow these instructions may result in serious injury or death!
WARNING!
You must wear a Fall Arrest System (FAS) comprising of a full-body fall
arrest harness, tree belt, lanyard, suspension relief device and climbing belt/ lineman’s
belt (as applicable) at all times after leaving the ground. You must stay connected at all
times after leaving the ground while using fixed position treestands. single safety belts
and chest harnesses are no longer allowed and should never be used. If you are not wearing
a full-body fall arrest harness that is properly attached to the tree to protect you from a
fall, do not leave the ground nor attempt to enter your treestand. Failure to follow these
instructions may result in serious injury or death!
WARNING!
Never attempt to climb up or down with a weapon and/or gear in your
possession. ALWAYS unload your weapon and pull it up to hunting height using a tether
or pull up rope. ALWAYS lower your unloaded weapon down to the ground prior (when
the ground) to attempting to climb up or climb down. Use this same method when raising
raising or lowering firearms, the chamber must be open and the barrel pointing toward
or lowering all other gear. Failure to follow these instructions may result in serious injury
or death!
ATTENTION!! WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!

This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
3
WARNING!
Prior to each use thoroughly inspect the treestand and all of its related
components and all safety devices before use for signs of wear, rot, corrosion, cracks,
deterioration and/or any other type of defect. Make certain that your treestand is tight
and secure prior to use. Protect this product from extended exposure to direct sunlight,
excessive heat or freezing temperatures by storing inside when not in use. DO NOT use
this or any other product(s) if it shows evidence of wear, rot, corrosion, cracks, deterioration
and/or any other type of defect. Failure to follow these instructions may result in serious
injury or death!
WARNING!
DO NOT use this or any other X-Stand™ product(s) if you have a history
of heart problems, back problems, impaired vision, joints that lock-up, spinal fusions,
equilibrium problems, high blood pressure, are not well-rested and/or any other physical
impairment that may limit your ability to use and/or operate this product(s) in the safe
manner outlined in this Instruction Manual. Additionally, do not use this or any other X-
Stand™ product(s) if you are currently taking medication (including prescription) and/or
using and/or consuming any substance, including alcohol, that may limit your ability to
use this X-Stand™ product(s) as outlined and described in the Instruction Manual. Never
use a treestand when feeling ill, nauseous or dizzy. Failure to follow these instructions may
result in serious injury or death!
WARNING!
DO NOT attempt to make adjustments to this product while in the treestand
All adjustments must be made with the entire treestand on the ground. Failure to follow
instructions may result in serious injury or death!
WARNING!
DO NOT leave your X-Stand™ product(s) installed for more than two weeks
(14 days). Any number of factors can jeopardize its installation and integrity. These include,
but are not limited to, weather or other environmental factors that can negatively affect its
performance. Animals can also cause damage to your X-Stand™ product(s) that can
negatively affect its performance and your safety. Additionally, factors such ast ree growth
can stress and damage supporting straps, cables, chains and/or buckles. Failure to follow
these instructions may result in serious injury or death!
WARNING! ALWAYS inspect the treestand and all safety devices prior to each use. DO
NOT use this product(s) if it shows signs of wear, damage, deterioration, or vandalism.
Factors such as tree growth, vandals, weather and animals may affect the performance of
an unattended treestand. Failure to follow these instructions may result in serious injury
or death!
WARNING!
DO NOT modify, fix/repair, alter, bend, cut, weld, drill or heat the treestand
in any way. Also, do not attach anything to your treestand without explicit authorized and
written instructions from the manufacturer. Failure to follow these instructions shall void
warranty and may result in serious injury or death!
WARNING!
Strict weight limitations have been set for each product to ensure your
personal safety. Note the weight limitations of your stand and that this weight limit includes
the user (one person) and their equipment. NEVER EXCEED THESE WEIGHT LIMITATIONS!
Failure to follow these instructions may result in serious injury or death!
WARNING!
DO NOT attempt to use this or any other X-Stand™ product(s) when ice,
snow, and/or freezing rain has deposited or formed on any portion of the tree or stand
you intend to climb. Do not attempt to use this or any other X-Stand™ product(s) when
thunderstorms are threatening and/or present within five (5) miles. Do not attempt to use
this or any other X-Stand™ product(s) when any other adverse weather condition presents
itself. These include, but are not limited to, weather conditions which have the potential
for producing winds, lightning, rain, snow, sleet and/or any other atmospheric condition
which may limit the user’s ability to operate this X-Stand™ product(s) in a safe manner
as described in this Instruction Manual. Should inclement weather conditions arise during
your use of this X-Stand™ product(s), return to the ground immediately. Failure to follow
these instructions may result in serious injury or death!
WARNING!
DO NOT jump or bounce on the treestand platform and/or the seat to
engage the stand to the tree. Failure to follow these instructions may result in serious
injury or death!
WARNING!
BEFORE each use, make sure all nuts and bolts are secure. CHECK all
hardware and webbing prior to every use to make sure that no damage has occurred
to hardware and that webbing (as applicable) is not cut or frayed. Keep webbing from
coming into contact with any sharp edges. DO NOT USE THIS PRODUCT IF ANY
DAMAGE IS SUSPECTED. Failure to follow these instructions may result in serious
injury or death!
WARNING! REPLACE
any damaged or worn part with original parts. Replace attach-
ment straps every one year and when not in use store in a dry, cool, safe place away from
sunlight. Never store a treestand or any of its components outdoors when not in use. To
purchase parts contact X-Stand™ Treestands at 540-877-2769. Failure to follow these
instructions may result in serious injury or death!
WARNING!
Always wear the appropriate foot wear when using a treestand. A good
non-slip safety boot is important for your safety. Be especially careful that boot laces
do not get hooked on the tree stand or its components (tuck shoelaces into boot before
climbing). Failure to follow these instructions may result in serious injury or death!
WARNING!
DO NOT use this product, or attempt to use a treestand, on a dead, leaning,
diseased, loose barked tree (bark that flakes or falls off), irregular shaped trees, or utility
poles. DO NOT use this product on any tree that does not allow for a level standing plat-
form. Failure to follow these instructions may result in serious or death!
WARNING!
NEVER hunt out of a treestand at heights at which you are not completely
comfortable. Depending upon the tree and hunting conditions, choose the minimum
hunting height that allows for safe, effective hunting. Failure to follow these instructions
may result in serious injury or death!
WARNING!
DO NOT use this, or any other X-Stand™ product(s) to climb utility poles,
telephone poles, structural columns or any other man-made structures. Never use this or
any other X-Stand™ product(s) around power generation (e.g., transformers, generators,
substations, etc.) and/or power transmission equipment. Never use a treestand on a dead
leaning, diseased or loose barked tree. NEVER USE A TREE BRANCH, OR ANY PORTION
OF A TREE, TO SUPPORT ANY PORTION OF YOUR WEIGHT OR AS A HAND HOLD. Failure
to follow these instructions may result in serious injury or death!
WARNING!
DO NOT stand on the treestand seat. Failure to follow these instructions
may result in serious injury or death!
WARNING!
This X-Stand™ Treestand product(s) was designed for installation on trees
with a minimum diameter of nine (9) inches (23 cm) to maximum diameter of twenty (20)
inches (51 cm) at treestand installation height (i.e., seat height). DO NOT use your X-Stand™
product(s) on trees with trunk diameters that do not meet these diameter requirements.
Failure to follow these instructions may result in serious injury or death!
WARNING!
A minimum of three (3) adults is required to install and/or remove a ladder-
stand. Failure to follow these instructions may result in serious injury or death!
WARNING!
The jaws (on applicable X-Stand™ ladderstands) and stabilization devices
When installing a ladderstand, always apply weight on first rung to set the
must be attached and tightened before attempting to climb to the seating/standing plat-
ladder firmly into the ground. Failure to follow these instructions may result in serious
forms. Failure to follow these instructions may result in serious injury or death!
WARNING!
injury or death!
WARNING!
Check the ground under ladderstands and climbing systems to make sure
ladder to tilt or shift off the tree as you climb. Failure to follow these instructions may result
it is firm and level. Sloping ground or uneven surfaces (one side on a rock) can cause the
n serious injury or death!
WARNING!
Always maintain three-point contact when climbing up or down atree.
Proper three-point contact means having either two feet with one hand or one foot with
two hands on the step portion of the ladder at all times when climbing up or down. Failure
to follow these instructions may result in serious injury or death!
WARNING!
Always lean forward as you climb and attach your full-body fall arrest
harness tree belt to the tree trunk before securing the platform to the tree and stepping
onto the platform. Failure to follow these instructions may result in serious injury or death!
ATTENTION!! WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
READ THIS MANUAL IN ITS ENTIRETY PRIOR RO USING THIS PRODUCT.

ATTENTION!! WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
This instruction manual complies with ASTM F2337 Standard Test Method for Treestand Fall Arrest Systems.
FULL-BODY FALL ARREST HARNESS USAGE INSTRUCTIONS & WARNINGS
FULL-BODY FALL ARREST HARNESS INSTRUCTIONS
WARNING!
Failure to read and strictly comply with the instructions contained here may
result in serious injury or death!
WARNING!
READ ALL THE INFORMATION INCLUDED HERE PRIOR TO ATTEMPTING TO
USE THIS FULL-BODY FALL ARREST HARNESS AND ITS COMPONENTS. YOUR FULL-BODY
FALL ARREST HARNESS AND ITS COMPONENTS ARE DESIGNED FOR A MAXIMUM WEIGHT
CAPACITY (USER AND EQUIPMENT) OF 300 POUNDS (136 KG). ADDITIONALLY, YOUR
FULL BODY FALL ARREST HARNESS AND ITS COMPONENTS MUST BE REPLACED AFTER
THREE (3) YEARS OF SERVICE! PLEASE CONTACT X-STAND™ TREESTANDS FOR FULL-
BODY FALL ARREST HARNESS REPLACEMENT PROCEDURE SHOULD YOU EXPERIENCE A
FALL OR SHOULD IT EXCEED THE THREE (3) YEAR SERVICE PERIOD.
WARNING!
Prior to attempting to use this or or any other X-Stand™ product(s) you
must take a moment and become familiar with its assembly, setup and installation. You
must practice installing, setting-up and using your full-body fall arrest harness at ground-
level prior to attempting to use it at heights above ground-level. Once you have become
thoroughly knowledgeable and comfortable with this product(s) setup, installation and
use at ground-level, you are now ready to use it at heights above ground-level. Failure to
follow these instructions may result in serious injury or death!
WARNING!
You must wear a Fall Arrest System (FAS) comprising of a full-body fall
arrest harness, tree belt, lanyard, suspension relief device and climbing belt/lineman’s
belt (as applicable) at all times after leaving the ground. You must stay connected at all
times after leaving the ground while using fixed position treestands. Single safety belts
and chest harnesses are no longer preferred and should never be used. If you are not
wearing a full-body fall arrest harness, do not leave the ground. Failure to follow these
instructions may result in serious injury or death!
WARNING!
ALWAYS practice using your full-body fall arrest harness (FAS) in the
presence of a responsible adult prior to using it in an elevated hunting environment,
and learn what it feels like to hang suspended in the harness at ground level. Practice
installing and using your treestand at ground level and with a responsible adult present
before you go hunting.
WARNING!
The length of the full-body fall arrest harness tether must be kept to a
minimum at all times during use. It should be adjusted so that it is above the head with
no slack (snug) in the sitting position. Never allow the full-body fall arrest tether to get
under your chin, around your neck, or under your arm(s). Failure to follow these instruc-
tions may result in serious injury or death!
WARNING!
Should you experience a fall there is time to make a correct decision on
what action needs to take place. It is important to remember: DO NOT PANIC! Failure to
follow this warning may result in serious injury or death!
WARNING!
If you have a limiting physical and/or health condition that precludes and/
or renders you incapable of self-recovery and/or a suitable escape plan is not available,
DO NOT hunt from heights above ground-level. Failure to follow these instructions may
result in serious injury or death!
WARNING!
FALLS FROM A TREESTAND CAN OCCUR ANYTIME AFTER LEAVING THE
GROUND. THESE FALLS COULD RESULT IN EITHER SERIOUS INJURY OR DEATH! FOR
YOUR PERSONAL SAFETY, PLEASE TAKE A MOMENT TO CAREFULLY READ THIS PRODUCT
INSTRUCTION MANUAL IN ITS ENTIRETY BEFORE ATTEMPTING TO ASSEMBLE, SET-UP,
INSTALL AND/OR OTHERWISE USE THIS X-STAND™ PRODUCT. AT LEAST ANNUALLY,
REVIEW THE CONTENTS OF THIS INSTRUCTION MANUAL AND WATCH THE SAFE TREE-
STAND HUNTING DVD. ADDITIONALLY, KEEP THESE INSTRUCTIONS FOR THE ENTIRE
DURATION THAT YOU OWN THIS PRODUCT(S). FAILURE TO FOLLOW THESE INSTRUCTIONS
MAY RESULT IN SERIOUS INJURY OR DEATH!
WARNING!
THE SAFE USE AND OPERATION OF THIS PRODUCT IS THE SOLE RESPONSI-
BILITY OF THE USER. IT IS ALSO THE SOLE RESPONSIBILITY OF THE OWNER TO PROVIDE
ANY PERSON(S) WHO BORROW OR PURCHASE THIS PRODUCT FROM THEM WITH THESE
COMPLETE INSTRUCTIONS. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN
SERIOUS INJURY OR DEATH! ADDITIONALLY, FAILURE TO FOLLOW THESE INSTRUCTIONS
MAY SUBJECT YOU TO PERSONAL LIABILITY PENALTIES AS DETERMINED BY THE U.S.
JUDICIAL SYSTEM.
WARNING!
Practice the use of your X-Stand™ Treestand full-body fall arrest harness
and suspension relief device (SRD) at ground-level in the presence of a responsible adult
to experience the feeling of hanging suspended before using in a hunting environment.
Failure to follow these instructions may result in serious injury or death!
WARNING!
NEVER allow the full-body fall arrest harness lanyard/tether to get under
your chin or around your neck.This poses a choking hazard that can lead to serious injury
or death. Failure to follow these instructions may result in serious injury or death!
WARNING!
If your hunting location is unknown by anyone and communication efforts
are unsuccessful, you must have a personal plan for self-recovery/escape should you
experience a fall. Prolonged suspension in a full-body fall arrest harness can be fatal. It is
important to exercise the legs by pushing against the tree or doing other forms of contin-
uous leg exercises to avoid blood pooling while being suspended. Varying degrees of
physical fitness may require different plans for self-recovery/escape the effects of pro-
longed suspension. Have a personal plan and practice it in the presence of a responsible
adult before leaving the ground. No one escape/ rescue plan will work for every hunter, on
every tree, in every circumstance. Only you can determine the best self-recovery/escape
plan for your hunting situation before leaving the ground. There is time to make a correct
decision on what action to take if a fall occurs while wearing a full-body fall arrest harness.
It is important to remember, DO NOT PANIC. Remain calm and implement your practiced
rescue, relief and recovery plan. Hunt from the ground when a self-recovery/escape ability
is absent. Failure to follow these instructions may result in serious injury or death!
WARNING!
READ THESE X-STAND™ TREESTANDS FULL-BODY FALL ARREST HARNESS INSTRUCTIONS CAREFULLY AND FOLLOW ALL THE INSTRUCTIONS! YOUR NEW FULL-BODY
FALL ARREST HARNESS IS DESIGNED FOR A MAXIMUM CAPACITY (USER & EQUIPMENT) OF 300 POUNDS (136 KG). ADDITIONALLY, YOUR NEW FULL-BODY FALL ARREST HARNESS MUST
BE REPLACED AFTER THREE (3) YEARS OF SERVICE! REPLACE YOUR HARNESS IMMEDIATELY SHOULD YOU EXPERIENCE A FALL WHILE WEARING IT.
WARNING!
You must use the X-Stand™ Treestand full-body fall arrest harness provided with this product or a harness that complies with ASTM standards. NOTE: You must store
your full-body fall arrest harness out of direct sunlight and out of any other harsh environmental condition(s) that may adversely affect its performance. Failure to follow these instruc-
tions may result in serious injury or death!
STEP 1.
Identify the main parts of the full-body fall arrest harness (see Fig. 1). Hold the
full-body fall arrest harness by the tether loop ensuring the harness is upright and leg
straps are hanging down. Straighten any parts that have become twisted. Insert arms
through each shoulder strap. (see Fig. 2)
Feed the left leg strap between legs and thread through the bottom left waist
loop. Repeat with the right leg strap, feeding between legs and through right waist loop.
(see Fig. 3)
READ THIS MANUAL IN ITS ENTIRETY PRIOR RO USING THIS PRODUCT.

This instruction manual complies with ASTM F2337 Standard Test Method for Treestand Fall Arrest Systems.
tree
belt
Tree Belt
Side View
Slot A
Left Leg
Strap
Right Leg
Strap
3 Bar
Buckle
Up through Slot B
Down through Slot A
Down through Slot B
Pull tight to secure
Back over top
Slot B
FIG 4
FIG 6 FIG 8
FIG 7
Sitting/
Seating
tree
belt
tether
tree
belt
Standing
tether
shoulder
strap shoulder strap
shoulder
strap shoulder strap
Leg Strap
waist
belt
Leg Strap
FIG 2
shoulder
strap shoulder strap
shoulder
strap shoulder strap
Leg Strap
waist
belt
Leg Strap
FIG 3
Tether
Tether
Loop
Tether
Loop
3 Bar
Buckle
3 Bar
Buckle
Front View Rear View
SRD Strap
Right
Waist
Loop
Right
Leg Strap Right
Leg Strap
Left
Leg Strap
Left
Leg Strap
Left
Waist
Loop
Tether
SRD Strap
FIG 1
tree belt
tether
FIG 5
Secure the two leg straps by threading the 3 bar buckle as shown in Figure 4.
Tighten the leg straps snuggly. DO NOT over tighten as this will cut off the circulation to
your legs. The X-Stand™ Treestands full-body fall arrest harness should look like the one
depicted in Figure 5 when done correctly. Note: If leg straps are too long, feed right leg
strap with buckle through bottom of the right waist loop, down the top of the left waist
loop and secure to left leg strap with 3 Bar Buckle as instructed.
WARNING!
It is very important to complete this Step of the assembly. Improperly
secured buckle may cause full-body fall arrest harness failure resulting in serious injury
or death! If there is not enough strap available to complete this step, DO NOT USE THIS
FULL-BODY FALL ARREST HARNESS! You may need to purchase and use a larger spe-
cialty sized full-body fall arrest harness that complies with ASTM standards.
Once you have reached your desired height, insert the tree belt through the loop
of the tether. (see Fig. 5) Then, carefully wrap the tree belt around the tree at a height
that allows just enough slack for you to sit comfortably in your stand. Keeping the tether
as short as possible limits the distance you will travel in the unlikely event you should
experience a fall. To secure the tree belt insert free end up through the slot in the buckle
closest to opposite end of the tree belt, then cross over the sliding mechanism and back
down through opposite slot. Pull on strap to secure and test to make sure sliding mecha-
nism engages creating secure strap placement. (see Fig. 6, 7, 8)
ATTENTION!! WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
READ THIS MANUAL IN ITS ENTIRETY PRIOR RO USING THIS PRODUCT.
STEP 3. STEP 4.

This instruction manual complies with ASTM F2337 Standard Test Method for Treestand Fall Arrest Systems.
To activate your product’s warranty, a registration card (found in the back of this manual)
must be completed and returned to the manufacturer within 30 days of purchase.
Be sure to keep a copy of this card for your records.
Should you have any questions about the assembly, installation or use of this X-Stand product,
or any other X-Stand products, please do not hesitate to call one of our customer service
representatives at 540-877-2769 and they will answer all questions you may have about any
of the complete line of X-Stand products.
STEPS TO FOLLOW IF A FALL WERE TO OCCUR:
Although no one plans to fall from their treestand, falls can and do occur without warning.
It is important to become familiar with the guidelines below and practice your recovery
plan at ground-level. Failure to read, understand, and follow these Steps may result in
serious injury or death!
WARNING!
There is time to make a correct decision on what action to take if a fall
occurs while wearing a full-body fall arrest harness.It is important NOT TO PANIC! Remain
calm and implement your practiced rescue, relief and recovery plan. Failure to follow these
follow these instructions may result in serious injury or death!
WARNING!
A suspension relief device must be on your person and readily accessible
while using a full-body fall arrest harness. This device will allow you to relieve the load on
the lower extremities if suspended in a full-body fall arrest harness and help maintain
circulation in the legs and mitigate suspension trauma (blood pooling). Follow all instruc-
tions below regarding the provided SRD (Suspension Relief Device) and NEVER remove it
from your full-body fall arrest harness. Failure to follow this warning may result in serious
injury or death!
STEP 1. After a fall, take a moment to catch your breath and stay calm; DO NOT PANIC.
Pull on the SRD strap located on the front right side of your full-body fall arrest
harness. (see Fig. 9)
STEP 4.
If you are able to reach your ladder or climbing system, use it to get back into
your secured treestand and then carefully climb down to ground-level. If you are not able
to reach your stand, remain calm and continue to stand in the SRD loop until help arrives.
(see Fig. 12)
STEP 3. Adjust the SRD strap so that you are able to step into the loop and then stand up
relieving the pressure on your lower extremities. The loop size can be adjusted by moving
the buckle up or down. (see Fig. 10 & 11)
Use your personal locating device or cell phone to call for help.
NOTE:
Several optional commercial products/systems are available that offer selfrecovery
or self extraction from a fall when suspended in a full-body fall arrest harness. Some
systems automatically descend the user while others allow user control. One of these
products/systems can be considered for use as an additional safety precaution against
prolonged suspension and suspension trauma. Be sure to follow the manufacturers’
directions on the safe use of these products/systems.
FIG 9
FIG 10
FIG 11 FIG 12
ATTENTION!! WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
READ THIS MANUAL IN ITS ENTIRETY PRIOR RO USING THIS PRODUCT.

MAX XL · PARTS LIST
XP19-0004 Top Ladder Section 1
1
1
XP19-0153 Top Step 1
XP19-0154 Side Frame 2
XP19-0567 Top Ladder Extension 2
XP19-0155 Foot Platform 1
XP19-0159 Under Support Gusset 2
XP19-0160 Side Support Gusset 2
XP19-0148 Support Bar 2
XP19-0150 Seat Support 1
XP19-0146 Rear Frame Support 1
XP19-0145 Left Armrest 1
XP19-0147 Right Armrest 1
1
1
XP19-0157 Seat Support Bar 1
XP19-0420 Support Bar Ladder Piece 1
XP19-0421 Support Bar Tree Piece 1
XP19-0432 Safety Sleeve 6
1
1
2
2
XP15-0581 Ratchet Strap (C) 2
XP19-0179 Cam Buckle Strap 2
XP15-0010 Full-Body Fall Arrest Harness 1
XP15-0020 Safety DVD 1
1
XP87-0007 1/4" x 1 1/2" Hex Bolt (A) 3
XP87-0009 1/4" x 1 3/4" Hex Bolt (B) 7
XP87-0015 1/4" x 2 1/2" Hex Bolt (D)
XP87-0014 1/4" x 2 1/4" Hex Bolt (C)
10
XP87-0067 5/16" x 2 3/4" Hex Bolt (F) 3
8
XP87-0016 1/4" x 3 1/4" Hex Bolt (E) 4
XP87-0023 1/4" Nylon Spacer 2
XP87-0027 Nylon Washer 66
XP87-0029 1/4" Nylock Nut 30
XP87-0047 5/16" Nylock Nut 3
XP87-0038 1/4" Wing Nut 2
Part # Description Qty Part # Description Qty
7
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
ATTENTION!! WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
READ THIS MANUAL IN ITS ENTIRETY PRIOR RO USING THIS PRODUCT.
XP19- 0005
XP19- 0006
Middle Ladder Section
Bottom Ladder Section
Backrest Support
Seat Assembly
Backrest Foam
Backrest Cover
Armrest Foam
Armrest Cover
Instruction Manual
XP19- 0230
XP19- 0232
XP19- 0235
XP19- 0236
XP19- 0233
XP19- 0234
XP19- 0237

NOTE: Part illustrations are for reference purposes only, and may not be to actual size.
MAX XL · HARDWARE DIAGRAM
8
{D} 1/4" x 2 1/2" Hex Bolt [10 pieces] {F} 5/16" x 2 3/4" Hex Bolt [3 pieces]
1/4" Wing Nut
[2 pieces]
1/4" Nylock Nut
[30 pieces] 5/16" Nylock Nut
[3 pieces] 1/4"Nylon Washer
[2 pieces]
Nylon Washer
[66 pieces]
Ratchet Strap C [2 pieces]
Cam Buckle Strap [2 pieces]
{E} 1/4" x 3 1/4" Hex Bolt [4 pieces]
{A} 1/4" x 1 1/2" Hex Bolt
[3 pieces]
{B} 1/4" x 1 3/4" Hex Bolt
[7 pieces]
{C} 1/4" x 2 1/4" Hex Bolt
[8 pieces]
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.

Side Frame
Side Frame
[C]
[C]
[C]
[C]
[C]
[D]
Foot Platform
Under Support
Gusset
Under Support
Gusset
Top Ladder
Section
Top Ladder
Extension
Top Ladder
Extensions Support Bar
Support
Bar [C]
[D]
[D]
[D]
Safety Sleeve
Safety
Sleeve
Top Step
Top Ladder Section
Top Ladder
Extension
Top Ladder
Extension
[D]
[D]
[B]
[B]
ASSEMBLY INSTRUCTIONS
-MAX XL -
NOTE: Steps 1-11 require you temporarily finger
tighten nuts to insure proper alignment.
FIGURE 1
FIGURE 2
9
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
STEP 1. Insert (2) safety sleeves and the top
ladder extensions onto top ladder section
and secure using (2) 1/4" x 1 3/4" hex bolts
(B), (4) nylon washers and two (2) 1/4" nylock
nuts. Note: When attaching the top ladder
extensions be sure that the bends are facing
outward. (Fig. 1)
STEP 2. Attach the top step to the front of the
STEP 3. Attach the support bars to the bottom
of the foot platform using (4) 1/4" x 2 1/4" (C),
(8) nylon washers and (4) 1/4" nylock nuts.
(Fig. 2)
STEP 4. Using (2) 1/4" x 2 1/2" (D), (4) nylon
washers and (2) 1/4" nylock nuts attach the
side frames and the foot platform to the
top ladder extensions. (Fig. 2)
STEP 5. Attach the under support gussets to the
inside of the support bars using (2) 1/4" x 2 1/4"
(C), (4) nylon washers and (2) 1/4" nylock nuts. Then
connect the under support gussets to the outside
of top ladder section using (2) 1/4" x 2 1/2" (D), (4)
nylon washers and (2) 1/4" nylock nuts. (Fig. 2)
top ladder extensions using (2) 1/4" x 2 1/2"
hex bolts (D), (4) nylon washers and (2) 1/4"
nylock nuts. (Fig. 1)

10
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
B
O
TTO
M
SEAT ASSEMBLY ·FIGURE 3A
Seat Support Bar
Seat
Support
[A]
[A]
Seat
Rest Seat
Rest
Loops
FIGURE 3
STEP 6. Insert seat
support bar into the
bottom of the seat
assembly aligning
the top holes of seat
assembly with seat
support bar. Secure
using (2) 1/4" x 1 1/2"
hex bolts (A), (4) nylon
washers and (2) 1/4"
nylock nuts. (Fig. 3A)
STEP 7. Slide the seat support to the
loops on the rear of the textilene
seat. (Fig. 3A)
WARNING! Armrests are provided for comfort and should be used as armrests only. The armrests are not
designed to carry the full weight of the user. Never place more than fifteen (15) lbs of force on the armrests.
Failure to follow these instructions may result in serious injury or death!
Armrest
Armrest
Side Support
Gusset
Side
Support
Gusset
Side
Frame
Foot Platform
Rear Frame
Support
Side Frame
Seat Assembly
Seat Support
Tab
Seat
Support
Bar
[F]
[F]
[F]
[E]
[E]
[D] [E]
[D] [E]
[C]
[C]
STEP8 . Insert the seat support onto the side frames aligning the holes. Secure the
side frame, seat support and side support gussets using (2) 1/4"x 2 1/2" hex
bolts (D), (4) nylon washers, and (2) 1/4" nylock nuts. Then secure the side supports
gussets to the outside of foot platform using (2) 1/4"x 2 1/4" hex bolts (C), (4) nylon
washers, and (2) 1/4" nylock nuts. (Fig. 3)

11
FIGURE 4
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
STEP 9. Rotate the seat support down aligning the lower holes with seat assembly.
Secure the front holes of armrests, seat assembly, side frames and seat supports
using (2) 1/4"x 3 1/4" hex bolts (E), (4) nylon washers, and (2) 1/4" nylock nuts. Note:
When attach correctly the tab should be inside. Then attach the rear holes of the
armrests to the seat support and seat assembly using (2) 1/4"x 3 1/4" hex bolts (E),
(4) nylon washers and (2) 1/4" nylock nuts. (Fig. 3)
STEP 11. Attach the upper holes of the armrests to the backrest supports using (2)
1/4"x 2 1/2" hex bolts (D), (4) nylon washers, (2) 1/4" nylon spacers and (2) 1/4" nylock
nuts. (Fig. 4) Note:The backrest support should be in front of tab.
STEP 10. Attach the rear frame support to the seat support using (3) 5/16"x 2 3/4"
hex bolts (F), (6) nylon washers, and (3) 5/16" nylock nuts. (Fig. 3)
STEP 12. Attach the armrest
foams, armrest covers,
backrest support foam
and backrest coveret to
the armrests and backrest
using velcro to secure.
(Fig. 4)
NOTE: SECURELY TIGHTEN EVERY NUT
AND BOLT AT THIS TIME.
WARNING! Backrest support is provided for comfort and should be used as backrest support only. The backrest
support not designed to carry the full weight of the user. Never place more than fifteen (15) lbs of force on the
backrest support. Failure to follow these instructions may result in serious injury or death!
Armrest
Backrest
Support
Foam
Backrest Support
Cover
[D]
[D]
Armrest
Armrest
Armrest Foam
Armrest
Foam
Armrest Cover
Tab
Armrest
Cover

12
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
ADJUSTABLE SUPPORT BAR ASSEMBLY
- MAX XL -
FIELD INSTALLATION
- LADDERSTAND
- MAX XL -
FIGURE 5
STEP 1. Assemble adjustable support bar by sliding support bar tree piece into
support bar ladder piece, secure them using (1) 1/4"x 1 1/2" hex bolts (A) and
the 1/4" wing nut.
STEP 2. Attach support bar to middle ladder section using (1) 1/4"x 1 3/4" hex
bolts (B) and the 1/4" wing nut.
WARNING! DO NOT attempt to install this
product on a tree that is not straight or
healthy. Make sure the tree is devoid of
dead branches, limbs, vines or any-thing that
might interfere with installation. DO NOT
attempt to install this treestand on a tree that
is leaning, diseased, crooked, has loose bark,
or does not meet the minimum installation
diameter of
nine (9) inches at treestand
installation height. Failure to follow these
instructions may result in serious injury or
death!
NOTE: The 1/4"x 1 1/2" hex
bolts (A) and the 1/4" wing nut
will be used to set the desired
length of the adjustable support
bar.
NOTE: These figure relate to
Step 5 of the Field Installation
Instructions on page 14.

FIGURE 1
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
STEP 1. Select a straight, healthy tree, one devoid of dead branches or loose bark.
DO NOT attempt to install this peoduct on a tree that is not healthy!
Top Ladder Section Middle Ladder Section Bottom Ladder Section
Top Ladder
Section
Safety Sleeve
[B]
[B]
Safety
Sleeve
Middle Ladder
Section
FIGURE 2
FIGURE 3
STEP 2. Assemble ladder sections beginning with top ladder section. Attach middle
ladder section to top ladder section. Attach bottom ladder section to the middle
ladder section. Each ladder section has slight design differences (Fig. 1) and need to
be assembled in the proper order for correct installation.
After assembling the ladder,
secure using (4)
1/4"x 1 3/4" hex bolts (B), (8) nylon washers and (4) 1/4" nylock nuts.
NOTE:
All ladder section will be assembled with the male end facing upward and fe-
male end (sleeves) facing downward (Fig. 2). The safety sleeves will be visible on the
outside
of the ladder section connection joints.
Rear Frame Support
Cam Buckle Strap
Bark Biters
STEP 3. Attach the two (2) long ends of the cam buckle
straps to each side of the rear frame support (near the
bark biters).
Secure straps by wrapping straps around
rear frame support and pulling through its looped end.
(Fig. 3) Then attach the two (2) ends of the cam buckle
straps with cam buckle to each side of the middle
ladder section column tubing (beneath the 5th rung up
as counted from the ground). Secure straps with cam
buckle by wrapping strap around vertical ladder leg
and pulling through its looped end. (Fig. 4) Feed the
free ends of the long straps through cam buckle and
tighten the cam buckle straps securely (see cam buckle
instructions).
NOTE: DO NOT attempt to install your
ladderstand without the straps firmly tied to the ladder.
NOTE: SECURELY TIGHTEN
EVERY NUT AND BOLT AT
THIS TIME.

This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
STEP 4. Place the ladderstand flat on the ground in front of the tree with the bottom
ladder section approxlmately 3 feet away from the base of the trunk. Then with at
least 3 adults, gently raise the ladderstand to a vertical position allowing the bark
biters to come into direct contact with the tree. Once elevated completely, carefully
pull the base away from the tree until the sitting & standing platform are parallel to
the ground. (Fig. 6)
STEP 5. Attach the adjustable support
bar to the
ladderstand. NOTE: The
adjustable support bar should be
attached to the sixth rung up from
the bottom of the ladder section
shown in Fig. 7, page 16. Adjust the
length so that the tree piece fits snugly
to the tree providing rigid support
to
the ladder; secure
them using (1) 1/4"
x 1 1/2" hex bolts (A) and the 1/4"
wing nut.
Once you have set the
adjustable
support bar, hook one end
of the ratchet strap in the hole on the
bark biter, wrap around tree trunk, and
connect toopposite side. Carefully
tighten the RATCHET STRAP securely.
(Fig. 5)
DERSTAND INSTALL
VITAL RATCHET INSTRUCTIONS
STEP 1. Thread strap through slot in the center of the ratchet reel
(Fig. 1). Remove slack from strap by pulling loose end until the t
is snug (Fig. 2)
STEP 2.
Then ratchet handle back and forth to tighten straps, a
minimum of two (2) wraps around the ratchet reel is required (Fig. 3).
STEP 3. After strap is tight, close handle to the lock position.
STEP 4.
To remove tension, pull spring loaded retaining lock
and open ratchet completely, then manually pull strap to loosen
(Fig. 4).
2X Min.
FIGURE 1 FIGURE 2
FIGURE 3 FIGURE 4
Insert long strap through buckle on short strap and pull tight to secure.
FIGURE 1 FIGURE 2 FIGURE 3
CAM BUCKLE INSTRUCTIONS
Middle
Ladder
Section
Cam Buckle
Strap
Vertical Ladder
Legs
FIGURE 4

This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
Adjustable
Support Bar
Ratchet Strap
FIGURE 5
FIGURE 6
WARNING! You must have three (3) adults to install or remove your stand from the tree. Failure to follow
these instructions may result in serious injury or death!
STEP 6.
When the ladderstand is level and
adjustable
support bar is secure, unlock
the cam buckle straps. Criss-cross cam
buckle straps behind
the tree trunk pulling
them snug. Then feed the free ends of the
long strap through the cam buckles and
tighten the cam buckle straps securely
again.
WARNING! The two (2) cam buckle straps must be attached and tightened prior to climbing to attach the
platform(s)
ratchet straps. Additionally, the adjustable support bar(s) and the adjustable support bar(s)
ratchet strap must be
installed prior to climbing to install the platform ratchet(s). Failure to follow these
instructions may result
in serious injury or death!
Raising the Ladderstand
into Installation Position
NOTE: Foot Platform must
be parallel to ground.

This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
WARNING! Prior to climbing, make sure that all the ladder sections are firmly connected with the proper
hardware in place. Make sure none of the sections have
become separated. If they are, do not climb the
ladder.
With the help of two other adults, lower the stand back down to the ground and reattach the ladder
rungs
and reinstall the hardware in the manner previously described. Failure to follow these instructions
may result
in serious injury or death!
WARNING! Prior to attempting to climb a ladderstand for the first time, make certain the feet of the bottom
rung ladder section are firmly planted on solid, level ground. If they are not firmly planted on level ground,
DO NOT climb the ladder. With the help of two (2) other adults, lower the
stand and find a suitable location
to safely install the ladderstand. Failure to follow these
instructions may result in serious injury or death!
FIGURE 7
Cam Buckle
Straps
Ratchet Strap
C
a
m
B
u
c
k
l
e
S
t
r
a
p
C
a
m
B
u
c
k
l
e
S
t
r
a
p
Ratchet Strap

RE 11
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
WARNING! Always lean forward while climbing. your full-body fall arrest harness tree belt to the tree
trunk prior to securing the platform to the tree and stepping on to the platform. Failure to follow these
instructions may result in serious injury or death!
WARNING! When climbing to secure the ratchet strap(s) on the platform(s), it is important to lean
forward when climbing to keep the stand centered and secure to tree trunk. DO NOT lean backwards
when climbint. Failure to follow these instructions may result in serious injury or death!
WARNING! Before attempting to climb the ladderstand bounce on the bottom ladder section to set the
ladder
into the ground before proceeding higher. Failure to follow these instructions may result in serious
injury or death!
Ratchet Strap
Rear Frame
Support
FIGURE 8
STEP 7. CRITICAL STEP! After installing the adjustable support bar and cam buckle straps, it is
now time to attach
the RATCHET STRAP(S) to the top section of your ladder stand. Ratchet straps
are attached at the contact point from the stand to the tree. Hook one end of the ratchet strap onto
the rear frame support, near the bark biters, wrap around tree trunk, and connect to opposite side.
Carefully tighten the
VITAL RATCHET STRAP securely (see Vital Ratchet Instructions above). NOTE:
THREE (3) VITAL RATCHET STRAPS ARE INCLUDED
AND NECESSARY FOR SOME MODELS.
ALWAYS USE ALL PARTS REQUIRED.
WARNING! Always maintain three-point contact when climbing up or down. Proper three-point contact
means having either two feet with one hand or one foot with two hands on the step portions of the climbing
aids and/or ladderstands at all times when climbing up or down. Failure to follow these instructions may
result in serious injury or death!
WARNING! The platform ratchet strap(s), cam
buckle straps and adjustable support bar(s) have
all been included with your new ladderstand to
ensure its solid attachment to the tree. All three
of these safety devices must be installed as out-
lined in this Instruction Manual. Failure to install
these safety devices as outlined in this Instruction
Manual may result in serious injury or death!
WARNING! Thid ptofuct(s) is designed for
adult use only! No one under the age of 16 shall
attempt to use this or any other product(s) without
direct adult supervision. Failure to follow these
instruction may result in serious injury or death!
STEP 8. You are now ready to use your ladderstand!

X-Stand Treestands | 21673 Cedar Avenue South | Lakeville, MN 55044
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.

To activate your product’s warranty, please mail in your registration card or submit it online at www. X-Stand.com
LADDERSTAND WARNINGS & PRODUCT REGISTRATION
Product Purchased Model Number
Serial Number
Owner’s Name
Street Address
City State Zip Code
E-mail Address Phone
Date Purchased
Purchased From (Dealer Name)
How did you hear about us: Catalog Webpage Friend Magazine
Other, Please Explain
Are you a: Bow Hunter Gun Hunter Both
Treestand Preference: Fixed Position Climbing Ladderstand
WARNING! The (2) cam buckle straps must be attached and tightened using prior to climbing
to attach the platform ratchet strap (ratchet strap C). Additionally, the lower bark biters
must be secured by the ratchet strap (ratchet strap C) and the lower bark biter is assembled
properly and attached to the middle ladder section prior to climbing to attached the platform
ratchet strap (ratchet strap C ). Failureto follow these instructions may result in serious
injury or death!
WARNING! Prior to climbing, make sure that all the ladders sections are firmly connected
with the proper hardware (snap pins) in place. Make sure none of the sections have become
separated. If they are, do not climb the ladder. With the help of two (2) other adults, lower
the stand back down to the ground and reattach the ladder sections and reinstall the hard-
ware in the manner previously described. Failure to follow these instructions may result in
serious injury or death!
WARNING! Prior to attempting to climb a ladder stand for the first time, make certain the
feet are secured into the ground (very bottom portion of the bottom ladder section), and
plated in level ground. If they are not firmly in level ground. DO NOT climb the ladder. With
the help of two (2) other adults, lower the stand and find a suitable location to safely install
the ladder stand. Failure to follow these instructions may result in serious injury or death!
WARNING! Before attempting to climb the ladder stand, bounce on the bottom ladder
section to set the ladder into the ground before attempting to climb the ladder stand. This
action should be completed before tightening the lower bark biters. Failure to follow these
instructions may result in serious injury or death!
WARNING! Always lean forward while climbing and securely attach your full-body fall
arrest harness tree belt to the tree prior to securing the platform to the tree. Failure to follow
WARNING! When climbing to secure the ratchet strap C on the treestand, it is important to
lean forward when climbing to keep the stand centered and secure to the tree trunk. DO NOT
lean backwards when climbing. Failure to follow these instructions may result in serious
injury or death!
WARNING! When climbing, always maintain three (3) points of contact as you ascend (climb
up) and while descending (climb down). Failure to maintain three (3) points of contact puts
the user at serious risk of bodily injury. Proper three (3) point contact means having either 2
feet with 1 hand or 1 foot with 2 hands on the step portions of the climbing aids and/or
ladder stands at all times when climbing up or down. Failure to follow these instructions may
result in serious injury or death!
WARNING! The Ratchet Strap C, the lower bark biter with ratchet strap C, and Cam Buckle
Straps have all been included All of these safety devices must be installed as outlined in the
Instruction Manual. Failure to install these safety devices as outlined in this Instruction
Manual may result in serious injury or death!
WARNING! This X-Stand™ product is designed for adult use only! No one under the age of
16 should attempt to use this or any X-Stand™ products without direct adult supervision.
Failure to follow these instructions may result in serious injury or death!
ATTENTION!! WHEN YOUSEE A " WARNING!" BE SURE TO HEED THEMESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
these instructions may result in serious injury or death!
22
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.

READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT. 
STANDARD LIMITED WARRANTY
Warranty: X-Stand™ Treestands warrant all X-Stand™ treestands, climbing system products and hunting
accessories to be free from defects in material and workmanship for a period of twelve months from
the original date of retail purchase. X-Stand™ Treestands warrants the enclosed hardware (where
applicable) is delivered to be free from physical defects for a period of twelve months from the original
date of retail purchase.
Repair Procedures, Exclusive Remedy: X-Stand™ Treestands will at its option, repair, or replace products
not conforming to this limited warranty at no charge. THIS IS THE SOLE AND EXCLUSIVE REMEDY
AVAILABLE FOR BREACH OF WARRANTY OR UNDER ANY OTHER LEGAL THEORY WITH RESPECT
TO X-STAND™ Treestands. If you find a product to be defective, contact the customer service depart-
ment at 540-877-2769. When you receive authorization, return the product as directed at your expense.
Product repairs not covered by warranty, and product updates, will be provided at a set rate.
Limitations: This warranty is void if the product is damaged by improper or abnormal use or by accident;
if the product is altered or modified in any way other than those directed by official X-Stand™ Trees-
tands instructions; or if any attempt is made to repair the product without authorization from X-Stand™
Treestands. It is solely the purchaser’s responsibility to determine the suitability of these products for
each particular application. X-Stand™ Treestands products are intended for hunting and hunting only.
X-Stand™ Treestands are in all events not suitable, and are not authorized, for use in any situations that
might pose potentially injurious to life and health, other than those situations that the products are
intended for. This warranty is not assignable or transferable.
No Other Warranties: EXCEPT AS PROVIDED IN THIS LIMITED WARRANTY SET FORTH IN THE WAR-
RANTY CARD SUPPLIED WITH X-STAND™ TREESTANDS AND INSTRUCTION SHEETS ARE PRO-
VIDED “AS IS”. ALL OTHER WARRANTIES AND REPRESENTATIONS, ORAL OR WRITTEN, EXP-
RESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHAN-
TABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED AND DO NOT APPLY. THERE
ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HERE OF. Except
as required by law, no representative, agent or employee of X-Stand™ Treestands is authorized to
make warranties, representations, or obligations inconsistent with or in addition to those set forth in this
limited warranty.
No Damages: IN NO EVENT WILL X-STAND™ Treestands BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM BREACH OF WARRANTY OR
UNDER ANY OTHER LEGAL THEORY, even if advised of the possibility of such damages. In no event
will X-Stand™ Treestands be liable for sums in excess of the purchase price of the product. X- Stand
Treestands is thus not liable for lost profits or goodwill; downtime; damage or destruction of items or
equipment used with, or in conjunction with, X-Stand™ Treestands; personal injury or loss; or any other
damages.
General: (a) This agreement is the entire agreement between you and X-Stand™ Treestands.; supercedes
any prior or different agreements, representations, or proposals; and may be changed only by written
agreement with X-Stand™ Treestands. (b) Waiver by any party of any default or breach of this agree-
ment will not constitute a waiver of any subsequent default or breach of the same of different kind.
(c) The invalidity of any provision of this agreement shall not affect the validity of the other provisions
hereof. (d) This agreement shall be governed by the laws of the State of Minnesota, U.S.A. X-Stand™
Treestands; Lakeville, MN 55044
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
23

21673 Cedar Avenue South Ⅰ Lakeville, MN 55044 Ⅰ 540-877-2769 • Fax: [phone]
This X-Stand™ product(s) has been tested to rigid industry standards. Safe operation and use of this X-Stand™ product(s) is the responsibility
of the user(s). Please read and follow all safe use instructions and warnings. Failure to follow these may result in serious injury or death!
First Edition, February 2019, Published by X-Stand™ TREESTANDS, Lakeville Minnesota.
© 2019 X-Stand™ TREESTANDS. All rights reserved.