Xantech CWTC10 User manual

CWTC10
10.4” Wireless Touch Controller
User’s Manual

REGULATORY NOTICES
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and radiates radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation.
CAUTION!
CAUTION! Danger of explosion if an improper battery is
substituted. If a replacement is needed, only replace with a
manufacturer issued battery pack.
Do not dispose of the battery pack in a fire. They may explode.
Check with local authorities for proper disposal instructions.

TABLE OF CONTENTS
1. GETTING STARTED..................................................................................1
1.1. WELCOME ....................................................................................1
1.2. SAFETY INSTRUCTIONS AND CARE OF YOUR CWTC10 ...............1
1.3. CHECKLIST ...................................................................................3
2. GETTING TO KNOW YOUR CWTC10 .............................................5
2.1. PARTS NAMES ..............................................................................5
2.2. THE CRADLE ................................................................................8
2.3. THE BATTERY AND AC ADAPTER ................................................9
2.4. THE STYLUS ...............................................................................10
2.5. TOUCH-SCREEN DISPLAY ...........................................................11
2.6. DISPLAY PROPERTIES .................................................................11
2.7. THE CRADLE ..............................................................................11
3. PANEL CONFIGURATION ................................................................. 12
3.1. DATA INPUT ...............................................................................12
3.2. BASIC SETTINGS……………………………………………12
SYNCHRONIZATION CONNECTING OTHER DEVICES ............................15
4. GETTING ONLINE................................................................................... 16
5. TROUBLESHOOTING ........................................................................... 17
6. SPECIFICATIONS .................................................................................... 19

- 1 -
1. Getting Started
1.1.Welcome
Congratulations! With your new CWTC10 you will be able to
control your WIC1200 Web Intelligent Controller or just about any
web server based system. The CWTC10 has a unique firmware build
of Window’s CE which secures the device for the specific intent of
displaying your control web page while preventing access to critical
setup and files. When the CWTC10 is turned on it will do only one
thing; display your control web page, allowing you to control your
custom system without worries of it controlling you. Your CWTC10
also gives you freedom with easy access to the Internet, and the
800X600 SVGA screen offers high resolution for all your control
system uses.
This manual will guide you through the unit’s simple set-up,
introduce you to its range of features and help you source extra
information.
1.2.Safety Instructions and Care of your CWTC10
CAUTION!
Danger of explosion if an improper battery is substituted. If a
replacement is needed, only replace with a manufacturer issued
battery pack.
•During normal usage and charging, the battery pack heats up.
This is caused by energy that has been generated and a chemical

- 2 -
charge that has occurred inside the battery pack. This is not a
cause for concern.
•You should charge batteries at temperatures from 10°C to 30°C
(from 50°F to 85°F). Lower temperatures require a longer
charging time.
•Do not carry a battery in your pocket, purse, or other container
where metal objects could short-circuit the battery pack. The
resulted excessive current flow can cause extremely high
temperatures and may result in damage from burns.
•Do not use your CWTC10 in a wet environment, for instance,
near a bathtub, sink, or any other place where there is risk of
moisture.
•To help prevent electric shock, plug the AC adapter into a three
prong, grounded power source. If a two-prong extension plug is
absolutely needed, use a 3-wire cable with properly grounded
plugs.
Do not dispose of the battery pack in a fire. They may explode.
Check with local authorities for-proper disposal instructions.
•When traveling, never check your CWTC10 as baggage. You can
put your CWTC10 through an X-ray security machine, but never
put your CWTC10 through a metal detector. Have a charged
battery with you in case you are asked to turn on the Tablet.
•When traveling, do not place the CWTC10 in an overhead
compartment where it can slide around. Do not drop your
CWTC10 or subject it to mechanical shocks.
•Protect your CWTC10 from environmental hazards such as dirt,
dust, food, liquids, temperature extremes, and over exposure to
sunlight.

- 3 -
•When you change environments rapidly, in respect to
temperature and humidity, with your CWTC10, condensation
may form on or within the Tablet. To avoid potential damage to
your CWTC10, allow sufficient time for the moisture to
evaporate before using.
•When disconnecting cables from your CWTC10, be sure to pull
on the connector or the strain relief loop, not on the cable itself.
As you pull, keep it evenly aligned to avoid bending the
connector pins. Never force a connector into a port. Make sure
the connector and port are aligned correctly.
•Before you clean your CWTC10, turn it off, remove the battery,
and unplug the power source.
•Clean your computer with a soft cloth dampened with water
rather than with liquid or aerosol cleaners.
•Clean the screen with a soft, clean cloth and commercial window
cleaner that does not contain wax or abrasives. Always apply the
cleaner to the cloth, not the screen. If the display contains grease
or some other contaminant, use isopropyl alcohol instead of
commercial cleaner.
1.3.Checklist
Check to see that the package your CWTC10 came in includes these
items:
•CWTC10
•Cradle
•AC Adapter

- 4 -
•Power Cord
•Battery Pack
•Stylus
•User Manual

- 5 -
2. Getting to Know Your CWTC10
2.1.Parts Names
Your CWTC10 features powerful functions and connectivity for you
to control your system via a touch panel interface.
This section outlines your CWTC10’s components.
Top Side
1. Power On/Off (Suspend/Resume) Switch
2. Future Expansion
3. SD Card Slot
4. Stylus Storage
12 3
4

- 6 -
Right Side
5. External Microphone jack
6. External Headphone jack
7. VGA-Out Connector
8. RS-232 Connector
567 8
Left Side
9. RJ-45 LAN Port
10. USB 2.0 Type A Port x2
11. DC IN Jack
910 11

- 7 -
Front
12. Function Keys Button
13. 4-way Mover Button
14. Keyboard Button
15. Wireless LED Indicator
16. Battery LED Indicator
17. Internal Speakers
18. Internal Microphone
12
1
4
15
1
6
17
13
18

- 8 -
Back
19. Hardware/Software Reset Switch
20. Battery Latches (Left one is also a Suspend/Resume switch)
2.2.The Cradle
The cradle lets you ‘dock’ your CWTC10 on your desk, making it
easy to read information, add peripherals, or to synchronize with
your PC.
21. Adjustable Kick Stand
22. USB 1.1 Type A Port x 2
23. USB Type B Port (Non Operational for 1041W)
24. DC IN jack
21
20
19

- 9 -
2.3.The Battery and AC Adapter
Your CWTC10 has two power sources, battery and AC. To run your
CWTC10 from the wall, use the supplied AC adapter cable.
The battery charges when the Tablet is connected to the AC power.
The indicator on the front of your CWTC10 displays the battery
status.
•Indicator solid green: Battery is fully charged
•Indicator solid orange: Battery is charging
•Indicator off: System is in the suspend mode
When fully charged and not in use, your CWTC10 battery has a two
week life.
2
22324

- 10 -
To check your battery level, or to adjust the time before your battery
switches off (power schemes) after the Tablet is continuously idle,
go to Start→Settings→Control Panel→Power, or double-click on
the power icon in taskbar.
For further tips on optimizing your battery, go to
Start→Help→Settings→Power.
2.4.The Stylus
The Stylus has been specially designed for use with your CWTC10.
IMPORTANT ：It is strongly recommended that you use the
provided stylus at all times; fingers or other
instruments may damage your screen.
If you find that your CWTC10 is not responding properly to your
taps, you may need to recalibrate your screen.
To do this, go to Start→Settings→Control Panel→Stylus.
Once there, select the Calibration tab and follow the instructions.
Your stylus can be conveniently stored in the side of your CWTC10.
The Suspend/Resume switch on the topside of your CWTC10,
when in the Suspend position, ensures that the touch panel isn’t
accidentally turned on.

- 11 -
Sliding the switch to the ON position resumes the Tablet.
2.5.Touch-screen Display
Your CWTC10 is equipped with a touch screen.
You can use the stylus that works like a mouse to click or double-
click a selected icon, and open it.
In addition, tap your touch panel desktop with your stylus for over
one second and it will act as ‘right-click”.
2.6.Display Properties
This function allows you to set the background on your desktop, and
the colors displayed on your interface.
To access these functions, go to Start→Settings→Control
Panel→Display→Background, or tap the desktop with your stylus
over one second, and it will act as ‘right-click’ to run the Display
properties.
2.7.The Cradle
The cradle lets you ‘dock’ your CWTC10, making it easy to use your
desk, to read information, or to add peripherals such as a keyboard or
a mouse.

12
3. Managing Your Information
3.1. Data Input
To input data into this CWTC10, you can choose to use the Software
Keyboard described below or an External USB Keyboard via a USB
1.1 keyboard as stated above.
Software Keyboard
The icon appearing in the taskbar provides you a Software
Keyboard functions like a real keyboard. The ‘CAP’ key locks the
keys to uppercase; the ‘Shift’ key switches the keys to uppercase for
one click only.
Once finished with the handwriting and keyboard, click on the
icon in taskbar and select Hide Input Panel.
3.2. Basic Settings
CWTC10 panel needs to be calibrated and configured in an
Administrator mode with the right static IP address and homepage
which will be opened in a Kiosk mode.
ACCESS ADMIN SETUP MODE
When the panel is powered for the first time, a message “Welcome to
the Xantech Commercial” is displayed. To leave this mode, and
change a homepage, you need to press-hold the upper-left touch

13
screen area for about 3-5 seconds. After that a window will pop up
and you will need to type a password to get to the Desktop.
Password: admin
Type password, click “Enter”, and “Exit To Desktop”.
CHANGING THE HOMEPAGE
To change a homepage go to “Internet Options” (Start -> Settings ->
Control Panel -> Internet Options). Type the address in the “Start
Page” line, and click OK. Restart the panel, and it will automatically
go to the Kiosk mode with the new homepage set by the user.
CHANGING AN IP ADDRESS
To change an IP address, you need to go to the “Network and Dial-
up Connections” (Start -> Settings -> Control Panel -> Network and
Dial-up Connections). Open up the Network icon, select “Specify an
IP address” and type your new IP address, Subnet Mask, and Default
Gateway. After you are done click OK, and changes would be
applied immediately. By default the CWTC10 is to DHCP mode.
CALIBRATING THE PANEL
To calibrate a panel go to “Stylus” option in Control Panel (Start ->
Settings -> Control Panel -> Stylus), and click on “Calibration” tab.
Click on “Recalibrate” button. Recalibration involves tapping the
center of a target and the panel measures new settings. Recalibration
is needed whenever you touch the screen, but the arrow appears in a
different place.

14
SAVING SETTINGS TO THE PERSISTENT MEMORY
To save settings, go to “Utility” option in Control Panel (Start ->
Settings -> Control Panel -> Utility), and click on “Registry
Manager” tab. Click on “Backup” button. It might take a couple of
seconds to save all the current settings.
RESTARTING THE PANEL
There are two ways to restart the panel: Software and Hardware
Reset. The buttons to restart the panel are located in the back of
device. Software Reset is just like rebooting the system, and does not
reset any settings that might have been set on the device. Hardware
Reset is rebooting the system, as well as resetting all settings on the
panel.
SUSPEND \ USER IDLE MODE
To change this setting, go to “Utility” option in Control Panel (Start -
> Settings -> Control Panel -> Power -> Schemes), and click on the
right Power scheme (Battery or AC) and than set User Idle and
Suspend time. During regular use, to get out of Idle of Suspend state,
simply tap the screen. Registry Manager” tab.

15
Synchronization Connecting Other Devices
Your CWTC10 is designed to support a number of external devices. The
two USB Type A ports on the left side let you add USB 2.0 keyboard,
mouse or Flash disk. Whereas the built-in SD Card slot allow you to
read/write memory cards from/to the CWTC10.

16
4. Getting Online
1. Double-click the Internal WLAN icon in your taskbar.
2. Select the “Wireless Information” tab.
3. Select your preferred network (AP) and click the Connect
button to associate.

17
5. Troubleshooting
For problems with your CWTC10, go to Start→Help. This brings
up a general user manual to reference. Most questions will be able to
be answered from this resource.
Common Problems / Frequently Asked Questions
The CWTC10 will not turn on!
•Make sure the Suspend/Resume switch (located on the top of the
panel) is set to ‘On’ (Resume)
•If device does not power on, use the AC Adapter to plug the
Tablet into the wall.
•If this does not turn the Tablet on, push the software reset button
located at the rear panel. (See the previous section titled Parts
Names.
I touch the screen with my stylus, and the mouse arrow
is in an entirely different place!
•This is a sure sign that you need to re-calibrate your touch screen.
•Go to Start→Settings→Control Panel→Stylus
•Click the calibration tab.
•Click “recalibrate” and follow the instructions.
How do I turn off my CWTC10?
•You can turn off your CWTC10 by simply sliding the Power
ON/OFF (Suspend/Resume) switch to “OFF” and hold for less
than 2 seconds. To resume your CWTC10, slide the Power
ON/OFF (Suspend/Resume) switch to “ON” position on the top
of your Tablet and release.