Xerox WorkCentre Pro 65 User manual

Read this
before
installing
WorkCentre Pro®65/75/90
604S14200
Network
Installation
Instructions

3
Xerox installation personnel deliver, unpack, and install the printer. They identify the documentation needed to sup-
port your printer. Materials may vary depending on model and options installed. Locate and distribute the following
materials as instructed below.
This document - For the System Administrator.
Page
4 - Connect the Printer to a Network
5 - Enable Scanning and E-mail Options
6 - Enable the Fax Option
7 - Enable the Network Accounting Option
8 - Enable Universal Serial Bus Printing
9 - Enable Image Overwrite Security
11 - 100BaseT Ethernet
13 - Static (Manual) TCP/IP Addressing
15 - Dynamic TCP/IP Address Assignment (DHCP/BOOTP/RARP)
17 - Novell NetWare 4.X and 5.X NDS
19 - UNIX / Linux (Solaris/SunOS) (HP-UX) (AIX)
21 - Microsoft Windows 2000 LPR and IPP Printing
23 - Microsoft Windows NT 4.0 Server (TCP/IP)
25 - Microsoft Windows (NetBEUI) Peer-to-Peer Networks
27 - WINS (Windows Internet Name Service)
29 - Apple Macintosh (AppleTalk)
31 - Port 9100 TCP/IP Printing
33 - E-mail
37 - Image Overwrite Security
39 - E-mail at a Glance
Other Documentation:
CD Pack
• Getting Started Leaflet – For the Machine Administrator/Operator. It provides steps to install the Customer
Documentation CD on a PC and the Environment, Health, and Safety information. Read and keep for refer-
ence.
• Information CD – For the Machine Administrator/Operator. Install the contents of this training CD on a public
server on your local area network for all users to access.
• Customer Documentation CD (x2) – Both CDs are the same. They contain PDFs of the user documentation
that are suitable for on-screen viewing or hard copy printing. It is recommended that you copy the User Guide
and the Features at a Glance files to a public server on your local area network to provide your users easy
access.
CentreWare - Give these to the System Administrator
• Network Scanning Services
• Scan to PC Desktop Standard
• Scan to PC Desktop Deluxe
Distribute Materials
604P14400

4
• See page titled 100BaseT Ethernet. Consult the System Administration Guide (PDF file) located on the
Customer Documentation CD, in the Customer Information Pack for a more in-depth explanation.
• For Wireless connection see System Administration Guide Supplement for more information.
• Select the appropriate Network or Protocol page in this document to finish the Network connection.
1.
2. • Locate the CentreWare® Print & Fax Drivers CD located in the CentreWare Network Services Pack.
Refer to the Getting Started With Network Services guide. Load the drivers, test the system and distrib-
ute the print drivers to users.
Note:
In addition to print and fax drivers, the CentreWare Network Services Pack contains a number of useful
tools such as:
CentreWare Print & Fax Drivers CD
• TIFF/PDF Submission Tool
• Font Management Utility
• Xerox Printer Configuration Utility
• Xerox Printer Installation Utility
CentreWare Printer Management CD
• Links to download Device Admin Wizard and Device Discovery
• Additional tools are available on this CD
Refer to the Getting Started with Network Services guide for more details.
Connect the Printer to a Network
604P14400

5
If you only received Basic Network Scanning plus E-mail, follow the instructions in step 1.
If you also received CentreWare Network Scanning (Standard or Deluxe), follow the instructions in steps 1 and 2.
When these options are enabled, you can convert paper documents into digital images. The scanned images can
be sent directly to network repositories or attached to an e-mail message sent directly from the printer. The printer
offers a range of walk-up e-mail features. You can search and select addresses using an existing company network
e-mail address book or an address list downloaded to the machine. Or type an e-mail address using the standard
keyboard provided on the touch screen. You can also activate Authentication (security) which requires users to
complete a valid network or optional guest login sequence before accessing optional features such as e-mail,
scanning and fax.
Enable Scanning and E-mail Options
Enable E-mail, Authentication and Basic Network Scanning
• To enable and configure servers for the E-mail and Authentication features, follow the instructions on
the E-mail page included in this document.
• To enable Basic Network Scanning, use the printers Internet Services (embedded web server). Consult
the System Administration Guide (pdf file) located on the Customer Documentation CD, in the Cus-
tomer Information Pack for a more in-depth explanation.
1.
2. Enable CentreWare Network Scanning
• Locate the CentreWare Network Scanning Services Pack. Refer to the Getting Started With Network
Scanning Services Guide and the System Administration Guide for help to install, configure, and use
the scanning features.
• To install Scan to PC Desktop (Standard or Deluxe) or other Image Management applications, follow
the installation instructions included with your Image Management application.
• If using CentreWare software, you can also configure your printer to scan to e-mail destinations via a
CentreWare Network Scanning Services distribution server or Microsoft Exchange Public Folders. You
can also create a scanning template repository for use by multiple printers rather than recreate them for
each machine. Locate the CentreWare Network Scanning Services Pack to obtain the software and
installation instructions for these options. Refer to the Getting Started with Network Scanning Services
Guide.
604P14400

6
Enable the Fax Option
Install the Network Fax software and any hardware on a network server using the vendor’s documentation
that accompanied the Network Fax components.
1.
Establish the Fax repository. Refer to your vendor’s Network Fax documentation for more information
2.
Set up the printers Fax Repository Settings. Use the System Administration Guide (pdf file) located on the
Customer Documentation CD in the CD Pack to assist you.
3.
If necessary, deploy client software, such as drivers, to enable faxing from the PC desktop. These drivers
should be supplied as part of the network fax software.
4.
Follow the steps below to make the printer a more complete part of your business process.
604P14400

7
Enable the Network Accounting Option
Set up the Network Accounting feature on your printer. Refer to the System Administration Guide (pdf file)
located on the Customer Documentation CD in the CD Pack for details.
1.
Install and configure the Network Accounting software using your vendor’s documentation. This will allow
you to connect the printer on your network, create user accounts, and set up reporting.
2.
Enable the Network Accounting option in the CentreWare print drivers.
The print drivers are part of CentreWare software. Instructions for print driver setup are found in the
CentreWare Print & Fax Drivers Guide (for Windows and Macintosh) (pdf file) located on the CentreWare
Print & Fax Drivers CD, in the CentreWare Network Services Pack.
The drivers are distributed without the Network Accounting option enabled. Users will need to enable the
accounting option.
3.
Follow the steps below to make the printer a more complete part of your business process.
604P14400

8
Enable Universal Serial Bus Printing
Verify the USB Print Kit has been installed and the USB Printer Port has been enabled by printing a
Configuration Report. See System Administration Guide Supplement for details on enabling the USB port.
1.
Connect your printer to a PC with a standard USB peripheral cable. The PC will detect the USB device. If
drivers are already installed, select the proper print driver.
If the drivers are not installed, the system will ask to install printer drivers. Use the Printer Driver CD to
install the proper print driver.
2.
Follow the steps below to make the printer a more complete part of your business process.
604P14400

9
Enable Image Overwrite Security
Image Overwrite Security enables On Demand Overwrite and Immediate Job Overwrite. to protect your
classified or private information.
• To enable and configure this security feature, follow the instructions on the Image Overwrite Security
page included in this document.
1.
Follow the steps below to make the printer a more complete part of your business process.
604P14400

10
Notes:
604P14400

11 604P14700
Before You Connect to a 100BaseT Ethernet
Network
The printer Ethernet Interface has speed settings of
10Mbps (10 Megabits per second), 100Mbps (100
Megabits per second) and Auto (AutoSensing).
If your network has hubs or concentrators that have
Auto-Sensing enabled, it is possible that if the
printer is set to Auto, the hub/concentrator will not
arbitrate to the correct speed.
Before you connect the printer to your network, perform
the procedure in the next column on this page entitled
Go to the printer and...
Go to the printer and...
1. Enter the Tools pathway
a) Press the Access ( or ) button.
b) On the keypad enter 1111 or the current
password. Press the Enter button when
finished. The Touch Screen will be used for
the remainder of the data entry, unless
instructed otherwise.
2. Set or Change the Ethernet speed.
a) Press the Connectivity and Network Setup
button.
b) Wait for the screen to refresh and press the
Physical Media button.
NOTE: Auto-Sensing hubs may not arbitrate cor-
rectly with the printer when Auto is selected. If
your hubs/concentrators support the 100BaseT
speed it is recommended you select 100Mbps in
Step d below. (Please be sure your Ethernet cable
is Category 5)
c) Select the desired Speed (10Mbps,
100Mbps,orAuto).
d) When finished with your changes press
Save.
3. Exit the Tools menu
a) Press the Exit Tools button.
NOTE: At this point the Network Controller is being
reset and initializing with the new setup. When
complete a Configuration Report will print.
b) Obtain the Configuration Report page from
your printer and verify that your settings have
been retained.
4. Connect your printer to the network with the
appropriate cabling.
5. Select the appropriate Network or Protocol Quick
Install Card and continue with the configuration.
100BaseT Ethernet

604P14700 12
Notes

13 604P14800
Before You Start
Verify the Ethernet connection is complete and the
desired speed is set. Then return to this page.
NOTE: By default, DHCP is enabled on the printer.
This card will show you how to disable DHCP and
manually set your TCP/IP information.
Your printer supports printing from a variety of operating
systems that support TCP/IP.
The procedure contained on this page will enable you to
connect your printer in any TCP/IP environment:
Record the following information:
Host Name ____________________________
IP Address ____________________________
Subnet Mask ___________________________
Default Gateway ________________________
Go to the printer and...
1. Connect your printer to the network with the appro-
priate cabling.
2. Enter the Tools pathway.
a) Press the Access ( or ) button.
b) On the keypad enter 1111 or the current
password. Press the Enter button when
finished.TheTouchScreenwillbeusedforthe
remainder of the data entry, unless instructed
otherwise.
3. Enter the Network Setup menus
a) Press the Connectivity and Network Setup
button.
b) Wait for the screen to refresh and press the
Network Setup button.
c) Press the TCP/IP Options button.
4. Enable the network interface and protocol.
a) Press the TCP/IP Settings button.
b) Press the Protocol and Media button.
c) Press the Enable button.
d) Press Save.
5. Disable Dynamic Addressing
a) Press the Dynamic Addressing button.
b) Press Disabled then press Save to retain
the settings and return to the TCP/IP
Settings screen.
6. Set the Host Name and TCP/IP Address
a) Press the Name/Address button.
b) Press the soft buttons on the Touch Screen
for each octet of the IP address and enter the
numbers using the keypad.
c) Press the Host Name button.
d) When the soft keypad appears, type the host
name EXACTLY as you want it to appear
with correct case. When finished press the
Save button twice to record the changes and
exit to the TCP/IP Settings Screen.
7. Set the Subnet Mask and Gateway
a) Press the Subnet and Gateway button.
b) Press the soft buttons on the Touch Screen
one at a time for each octet of the Subnet
Mask and enter the numbers using the
keypad.
c) Repeat this process for the IP Gateway
address. When finished press Save to record
the changes and exit to the TCP/IP Settings
screen.
NOTE: The Broadcast Address will be calculated
automatically.
8. Enable lp or lpr printing (skip steps 8a-8c if you
DO NOT want to print using lp or lpr).
a) Press the Close button.
b) Press the TCP/IP - Line Printer button. At
the next screen press the Enable button.
NOTE: While you can change the port number at
which your printer will accept lpr print jobs it is
recommended that you do this ONLY with extreme
caution as most lpr spoolers are set to send print jobs
to the default port.
c) If you wish to change the lpr port for your
printer press the Port Number soft button
and enter the desired port number at the
keypad. Press Save.
Static (Manual) TCP/IP Addressing

604P14800 14
9. Enable HTTP/IP.
a) Press the HTTP/IPP button.
b) Press Enable.
c) Press Save
10. Print a Configuration Report.
a) Press the Close button three times
b) Select System Settings.
c) Select Configuration Report.
d) Select Print Configuration Report Now.
e) Press the Cancel button.
11. Exit the Tools menu
a) Press the Exit Tools button.
NOTE: At this point the Network Controller is being
reset and initializing with the new setup. When
complete a Configuration Report will print.
b) Obtain the Configuration Report page from
your printer and verify that your settings have
been retained.
12. Prepare for print driver installation
a) From the documentation package supplied
with your printer, retrieve the CentreWare
Print and Fax Drivers CD and the leaflet
entitled Getting Started with Network
Services. Proceed to the next section of this
procedure called Go to a Workstation and...
Go to a workstation and...
1. Create a test job and send it to the printer with an
lpr utility or through a queue your operating system
may support.
2. Check your test job for quality and use the problem
solving section of the Reference Guide for
resolving print defects.
3. If your job does not print, refer to the
troubleshooting section in the System
Administration Guide (pdf file) located on the
Customer Documentation CD to correct the
problem.
4. Repeat this Go to a workstation and... procedure
at each workstation that will print to this printer.
Setup DNS (if required)
Go to the printer and...
1. Configure DNS
a) Repeat steps 2 through 4a
b) Select the DNS Configuration button.
c) Select the Domain Name Button. Again select
the Domain Name Button. Type in the domain
name then select Save then select Close.
d) Select the Preferred DNS Server button.
Press the soft buttons on the Touch Screen for
each octet of the IP address and enter the
numbers using the keypad. Select Save.
e) Select the Alternate DNS Server button. For
each Alternate Server, Press the soft buttons
on the Touch Screen for each octet of the IP
address and enter the numbers using the
keypad. Select Save.
f) Press the Exit Tools button.
Static (Manual) TCP/IP Addressing

15 604P14900
Before You Start
Verify the Ethernet connection is complete and the
desired speed is set. Then return to this page.
NOTE: By default, DHCP is enabled on the printer.
DHCP/BOOTP/RARP servers vary in the information
that they return to the device requesting service. Consult
the documentation supplied with your DHCP or RARP
server software to verify what TCP/IP information it can
supply. Your printer can retrieve the following values
from DHCP, BOOTP and RARP servers:
TCP/IP Address
Host Name (DHCP)
Subnet Mask
Gateway TCP/IP Address
Broadcast Address (DHCP)
Domain Name (DHCP only)
Preferred and Alternate DNS Server (DHCP)
Wins Server (DHCP)
Go to the dynamic server and...
1. Configure the DHCP, BOOTP, or RARP server with
the TCP/IP information you want assigned to your
printer. Use the documentation supplied with your
server for this task.
Go to the printer and...
2. Connect your printer to the network with the
appropriate cabling.
3. Enter the Tools pathway
a) Press the Access ( or ) button.
b) On the keypad enter 1111 or the current
password. Press the Enter button when
finished.TheTouchScreenwillbeusedforthe
remainder of the data entry, unless instructed
otherwise.
4. Enter the Network Setup menus.
a) Press the Connectivity and Network Setup
button.
b) Wait for the screen to refresh and press the
Network Setup button.
c) Press the TCP/IP Options button.
5. Enable TCP/IP printing.
a) Press the TCP/IP Settings button.
b) Press the Protocol and Media button.
c) Press the Enable button.
d) Press Save.
6. Select either DHCP, BOOTP, or RARP as the
dynamic address source.
a) Press the Dynamic Addressing button. By
default, DHCP will be selected. To change or
disable DHCP, choose another dynamic
addressing method (BOOTP, DHCP, DHCP/
AutoNet, RARP) or Disabled.PressSave.
b) Press the Exit Tools button. Wait
approximately 2 minutes before you continue
to Step 7.
7. Print a Configuration Report page and verify
the TCP/IP information was assigned correctly
by the dynamic server.
a) Repeat Steps 3a and 3b
b) Select System Setting.
c) Select Configuration Report.
d) Select Print Configuration Report Now.
e) Press the Cancel button.
f) Press the Exit Tools button.
To change the host name...
8. Set the Host Name
a) Repeat steps 3a-5a.
b) Press the Name/Address button.
c) By default, the printer assigns a default host
name. To change the host name, type the
host name EXACTLY as you want it to
appear with correct case. When finished
press the Save button twice to record the
changes and exit to the TCP/IP Settings
Screen.
Dynamic TCP/IP Address Assignment (DHCP/BOOTP/RARP)

604P14900 16
To enter a Subnet Mask and Gateway
Address...
NOTE: The printer will only accept one Gateway
address from a DHCP server.
9. Press the Subnet and Gateway button.
a) Press the soft buttons on the Touch Screen
one at a time for each octet of the Subnet
Mask and enter the numbers using the
keypad.
b) Repeat the process for the IP Gateway
address. When finished press Save to
record the changes and exit to the TCP/IP
Settings screen.
c) Press the Close button.
To enable LP and LPR printing
10. Press the TCP/IP - Line Printer button. At the
next screen press the Enable button.
NOTE: While you can change the port number at
which your printer will accept lpr print jobs it is
recommended that you do this ONLY with extreme
caution as most lpr spoolers are set to send print jobs
to the default port.
a) If you wish to change the lpr port for your
printer press the port number soft button
and enter the desired port number at the
keypad. Press Save.
NOTE: Your printer will not reboot unless you have
changed a physical media setting.
11. Enable HTTP/IPP
a) Press the HTTP/IPP button. At the next
screen press the Enable button. Then press
Save.
b) Press the Close button three times.
12. Print a Configuration Report page and verify
the TCP/IP information was assigned correctly.
Repeat steps 7b - 7f
Note: Update the lease time (if necessary) at the
DHCP/BOOTP server depending on your printer
usage patterns. Consult your DHCP server
documentation for details.
Note: If your RARP Server does not dynamically update
its /etc/ethers and /etc/hosts fields with a host name, you
will need to do this manually. Consult your RARP or
BOOTP server documentation for details.
Where to go from here
After you have verified that the TCP/IP information you
have assigned to your printer is correct, retrieve the
Quick Install Card that applies to your network operating
system or protocol and perform the procedures
indicated.
Now that the TCP/IP information has been provided, you
are able to print via a Web Browser (HTTP), an IPP
capable operating system, or to TCP/IP Port 9100. For
further information, please reference Microsoft
Windows 2000 LPR and IPP Printing Quick Install
and Port 9100 TCP/IP Printing Quick Install Cards.
Dynamic TCP/IP Address Assignment (DHCP/BOOTP/RARP)

17 604P15000
Before You Start
Verify the Ethernet connection is complete and the
desired speed is set. Then return to this page.
NOTE: If you wish to connect your printer using NDPS,
you may download the Xerox Gateway and printer
drivers from www.xerox.com.
The CentreWare software supplied with your printer can
be used to set up your printer on your Novell network.
Refer to the leaflet entitled Getting Started with
Network Services in the CentreWare Network
Services Pack. This procedure assumes you ran
NWADMIN or PCONSOLE to set up a print server
object. Please refer to the documentation supplied by
Novell to complete this task. Record precisely (Observe
upper and lower case, dot notation etc.) the following:
NDS Tree _____________________________
NDS Context Name ______________________
Print Server Name _______________________
Print Server password _____________________
NOTE: The ethernet component of the printer serves as
a Print Server for the device. You may choose to create
passwords for your Print Server. When your printer will
service queues on multiple fileservers, the Print Server
name must be the same on all fileservers and the Print
Serverpasswordmustbethesameonallfileservers.If
you choose not to use Print Server password, you must
leave the password for print server object in the Novell
tree blank as well as the password field on the printer.
Go to the printer and...
1. Connect your printer to the network with the appro-
priate cabling.
2. Enter the Tools pathway.
a) Press the Access ( or ) button.
b) On the keypad enter 1111 or the current
password. Press the Enter button when
finished.TheTouchScreenwillbeusedforthe
remainder of the data entry, unless instructed
otherwise.
3. Enable the Network Protocol
a) Press the Connectivity and Network Setup
button.
b) Wait for the screen to refresh and press the
Network Setup button.
c) Press the NetWare button.
d) Wait for the screen to refresh and press the
Protocol and Media button.
e) Press the Enable button.
f) Press Save.
4. Set the Frame Type
a) Press the Frame Type button.
b) Select the frame type desired (or Auto for
the printer) then press Save to retain your
changes and exit to the NetWare Options
screen.
5. Set the NDS Settings
a) Press the NDS Settings button.
Novell suggests using typeful names when entering
Name Context and Directory Service Tree information.
TYPEFUL NAME EXAMPLE:
cn=contextname.ou=organization.o=company.c=country
b) At this screen press the Name Context
button and use the touch panel keyboard to
enter the context in which this printer
resides. To access numeric characters and
punctuation, press the More Characters or
123 button. When finished press Save.
c) Press the Directory Service Tree button
and enter the NDS tree name where the
Context chosen in the previous step resides.
When finished press the Save button twice
to record the changes and exit the screen.
Novell NetWare 4.X and 5.X NDS

604P15000 18
6. Set the Print Server Name and Password.
a) Press the Print Server button.
b) Press the Print Server Name button and
use the Touch Screen keyboard to enter the
name you assigned to your print server (it is
recommended you use all UPPER CASE
characters). A default name will appear. Use
the backspace key (it looks like an arrow
pointing to the left) to clear out the default
name prior to entering your new name. To
include numbers or other characters in the
name press the More Characters or 123
button. When finished press Save to retain
the changes and return to the Print Server
screen.
c) Press the Print Server Password button
and use the touch screen keyboard to enter
the print server password in the correct case
you recorded when you set up your print
server then press Save.
d) Press Save to exit the Print Server screen
and save your changes.
7. OPTIONAL STEP: Change the desired SAP rate
or Poll Interval for your printer or set the Primary
File Server.
a) Press the Rates button and press SAP
Enable.
b) Press the box under SAP Rate or Poll
Interval and enter the desired number from
the keypad. The default values are
recommended. When finished, press Save
to retain your changes and return to the
NetWare Options screen
c) Press the Primary File Server button. At this
screen press the Name Context button and
use the touch panel keyboard to enter the
context in which this printer resides. To
access numeric characters and punctuation,
press the More Characters or 123 button.
When finished press Save.
d) Press the Exit Tools button. Allow
approximately 2 minutes for the software to
reset with the new settings.
8. Prepare for print driver installation
a) From the documentation package supplied
with your printer, retrieve the CentreWare
Network Services Pack. Proceed to the
next section of this procedure called Go to a
Workstation and...
Go to a workstation and...
1. Use the CentreWare Print and Fax Drivers CD to
install print drivers on a Windows-based worksta-
tion. Details for this are found in the leaflet Getting
Started with Network Services.
2. Connect the print driver you loaded above to the
queue you created on the NetWare server.
3. Open an application and print a test job.
4. Check your test job for quality and use the problem
solving section of the Reference Guide (pdf file)
locatedontheCustomer Documentation CD for
resolving print defects.
5. If your test job does not print, refer to the
troubleshooting section in the System
Administration Guide (pdf file) located on the
Customer Documentation CD to correct the
problem.
6. Repeat this Go to a workstation and... procedure
at each workstation that will print to this printer.
Novell NetWare 4.X and 5.X NDS

19 604P15100
Before You Start
Verify the Ethernet connection is complete and the
desired speed is set. Then return to this page.
NOTE: By default, DHCP is enabled on the printer.
This card will show you how to disable DHCP and
manually set your TCP/IP information.
You can use BOOTP or RARP servers to assign TCP/IP
information to your printer. Refer to the RARP or BOOTP
Quick Install Cards for details.
Record the following information on this card for use
during the procedure:
Host Name ____________________________
IP Address ____________________________
Subnet Mask ___________________________
Default Gateway ________________________
Your printer supports printing from a variety of UNIX
platforms. Linux users should complete steps 1 through
7andthenskiptostep2oftheGo to a workstation
and... section to complete installation.
Go to the printer and...
1. Connect your printer to the network with the appro-
priate cabling.
2. Enter the Tools pathway.
a) Press the Access ( or ) button.
b) On the keypad enter 1111 or the current
password. Press the Enter button when
finished.TheTouchScreenwillbeusedforthe
remainder of the data entry, unless instructed
otherwise.
3. Enter the Network Setup menus.
a) Press the Connectivity and Network Setup
button.
b) Wait for the screen to refresh and press the
Network Setup button.
c) Press the TCP/IP Options button.
4. Enable the network interface and protocol.
a) Press the TCP/IP Settings button.
b) Press Dynamic Addressing.
c) Press Disabled then press Save.
d) Press the Protocol and Media button.
e) Press the Enable button.
f) Press Save.
NOTE: The Broadcast Address will be calculated
automatically.
5. Set the Host Name.
a) Press the Name/Address button.
b) One at a time press the soft buttons on the
Touch Screen for each octet of the IP
address and enter the numbers from the
keypad.
c) Press the Host Name button.
d) When the soft keypad appears, type the host
name EXACTLY as you want it to appear
with correct case. When finished press the
Save button twice to record the changes and
exit to the TCP/IP Settings Screen.
6. Set the Subnet Mask and Gateway
a) Press the Subnet and Gateway button.
b) Press the soft buttons on the Touch Screen
one at a time for each octet of the Subnet
Mask and enter the numbers using the
keypad.
c) Repeat this process for the IP Gateway
address. When finished press Save to record
the changes and exit to the TCP/IP Settings
screen.
d) Press the Close button.
e) Press the TCP/IP - Line Printer button. At
the next screen press the Enable button.
NOTE: While you can change the port number at
which your printer will accept lpr print jobs it is
recommended that you do this ONLY with extreme
caution as most lpr spoolers are set to send print
jobs to the default port.
f) If you wish to change the lpr port for your
printer press the port number soft button
and enter the desired port number at the
keypad. Press Save.
UNIX / Linux (Solaris/SunOS) (HP-UX) (AIX)

604P15100 20
7. Enable HTTP/IP.
a) Press the HTTP/IPP button.
b) Press Enable.
c) Press Save
8. Print a Configuration Report.
a) Press the Close button three times
b) Select System Setting.
c) Select Configuration Report.
d) Select Print Configuration Report Now.
e) Press the Cancel button.
f) Press the Exit Tools button.
9. Prepare for print driver installation
a) From the documentation package supplied
with your printer, retrieve the CentreWare
Network Services Pack. Proceed to the
next section of this procedure called Go to a
Workstation and...
Go to a workstation and...
1. Mount the CentreWare Print and Fax Drivers
CD andloadtheDCPR Tool. Details for these
procedures are contained in the leaflet entitled
Getting Started with Network Services.
2. Add the printers host name, TCP/IP address,
hardware address to your /etc/hosts file or NIS
database depending on your UNIX version.
3. Create a queue using the CentreWare tool OR
by using the native tools available in your operat-
ing system version.
4. Create a print job and send it to the printer.
5. Check your test job for quality and use the prob-
lem solving section of the Reference Guide (pdf
file) located on the Customer Documentation
CD for resolving print defects.
6. If your test job does not print, refer to the trouble-
shooting section in the System Administration
Guide (pdf file) located on the Customer Docu-
mentation CD to correct the problem.
7. Repeat this Go to a workstation and... proce-
dure at each workstation that will print to this
printer.
NOTE: You may establish connectivity to your
printer using the print utilities native to the UNIX
operating system. CentreWare need not be installed
to create a print device on the workstation. The
extended device functions offered through Centre-
Ware, however, may not be available as the operat-
ing system manufacturer may not provide a Xerox
printer model.
UNIX / Linux (Solaris/SunOS) (HP-UX) (AIX)