Xerox 3250D - Phaser B/W Laser Printer User manual

Version 1.3
April 2009
IPv6 Supplement:
Configure IP Settings and IP Filtering

©2009 Xerox Corporation. All rights reserved. Xerox and the sphere of connectivity design are trademarks of Xerox Corporation in the
United States and/or other countries.
Changes are periodically made to this document. Changes, technical inaccuracies, and typographic errors will be corrected in
subsequent editions.
Document Version: 1.3 (April 2009).

Configure IP Settings and IP Filtering 1
1
IPv6 Supplement
Configure IP Settings
This procedure enables the System Administrator to enable and configure IPv6 and IPv6 Filtering on
some Xerox WorkCentre/Phaser mono printers and Xerox WorkCentre/Phaser mono MFP products via
CentreWare Internet Services (CWIS).
Check the Xerox Support Website www.support.xerox.com for your Xerox product to determine if it
supports IPv6, and whether the firmware level loaded on your Xerox product supports IPv6. Print a
Configuration Report from your Xerox device (under the Reports menu) and check the version of the
firmware. If it is less than the firmware listed on the website then you need to download new firmware
to enable IPv6 capabilities.
1. At your Workstation, open the Web browser and enter the TCP/IP Address of the machine in the
Address bar.
2. Press [Enter].
3. Click on the [Properties] tab.
4. Click on the [Connectivity] link.
5. Click on the [Protocols] link.
6. Select [TCP/IP] from the directory tree.
7. Scroll down the page to TCP/IPv6 area, for the Protocol click the [Enabled]checkbox.
Stateless Addresses
The Link-Local Address is automatically populated.
Default DHCPv6 (Dynamic Host Configuration Protocol) Settings
The device performs auto-address DHCPv6 configuration every time it powers up. This is used for
neighbour discovery and address resolution on the local IPv6 subnet.
However, you can choose to use manual configuration, automatic configuration or a combination of
automatic and manual configuration.
8. Select one of the following options:
•[Use DHCP as directed by a router] - this option is fully automatic. The DHCPv6 Address will
be obtained and displayed on the screen.
•[Always Enable DHCP] - this option is fully automatic. The DHCPv6 Address will be obtained
and displayed on the screen.

IPv6 Supplement
Configure IP Settings and IP Filtering2
•[Never use DHCP] - when this option is selected, you must configure the Manual Address
Options and DNS separately.
Note: If [Use DHCP as directed by a router] is selected, then skip the Manual Address Options
section below and proceed to the DNSv6 section.
Manual Address Options
The device can be configured with up to 4 manual IPv6 addresses.
9. Click the [Enabled] checkbox for Manual Address if required.
10. The Router Prefix is derived from router advertisements. Select a router address prefix from the list
supplied in the [Router Prefix] menu. Click [Add] to populate the prefix for manual entry address.
11. Enter the manual IPv6 address (interfaceID) to append to the Router prefix.
Note: The Host Name is populated when configured at the IPv4 screen. If you change the Host
Name here it will also change it for IPv4.
DNSv6
12. Enter a valid [IPv6 Domain Name].
13. Enter an IP address for the [Primary DNSv6 Server Address].
14. Enter an IP address for [Secondary DNSv6 Server Address].
15. Check the box to enable [Dynamic DNSv6 Registration].
Note: If your DNS Server does not support dynamic updates there is no need to enable DDNS.
16. Scroll down the page and click on the [Apply] button to save the changes. If prompted, enter the
Administrator’s User ID [admin] and Password [1111], and click on [Login].
17. Click on [OK].
Test Access
1. At your Workstation, open the Web browser. In the TCP/IP Address bar, enter “http://” followed by
the Internet address of the machine. Then press the <Enter> key on the keyboard.
If you use the domain name to specify the machine, use the following format.
http://myhost.example.com
If you use the IP address to specify the machine, use one of the following formats depending on
your machine configuration. The IPv6 format is supported on Windows Vista only. An IPv6
address needs to be enclosed in square brackets.
IPv4: http://xxx.xxx.xxx.xxx
IPv6: http://[xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx]
Note: If you have changed the port number from the default port number “80”, append the
number to the Internet address as follows. In the following examples, the port number is 8080.
Domain name: http://myhost.example.com:8080
IPv4: http://xxx.xxx.xxx.xxx:8080
IPv6: http://[xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx]:8080
2. Verify that the home page of CentreWare Internet Services is displayed.

IPv6 Supplement
Configure IP Settings and IP Filtering 3
The CentreWare Internet Services installation process is now completed.
Note: If the Accounting feature is enabled, you may be required to enter a user ID and passcode
(if one is set up).
Note: When your access to CentreWare Internet Services is encrypted, enter “https://” followed by
the Internet address, instead of “http://”.
Note: DHCP/DDNS: Release Registration – Allows DHCP resources to be released when the
machine is powering down. This is a display-only item and shows “Enabled”.
IP Filtering
Overview
The IP Filtering is a security feature that allows you to control access to Internet Services. IP Filtering
allows you to prevent unauthorized access by TCP/IP (Transmission Control Protocol/Internet Protocol).
The IP Filtering feature provides security to the machine, by allowing you to register the IP addresses
permitted to communicate with the machine.
Enable IP Filtering
1. At your Workstation, open the web browser, enter the TCP/IP Address of the machine into the
Address bar.
2. Press [Enter].
3. Click on the [Properties] tab.
4. Click on the [Security] link.
5. Select [IP Filtering] in the directory tree.
For IPv6 Filtering
6. Checkmark the [IPv6 Filtering Enabled] box.
7. Enter the permittable IP Address(es) access to the device in the following IP Address table.
Enter the IPv6 address in form of CIDR convention. Prefix indicates the number of leftmost bits to
be referenced.
For example:
• 2001:DB8:1234:215:215:99FF:FE04:D345 / 128 is used to reference a complete address.
• 2001:DB8:1234:215:215:99FF:FE04:D345 / 64 is used to reference prefix address consisted
of leftmost 64 bits only.
• 2001:DB8:1234:215:215:99FF:: / 80 is used to reference prefix address consisted of leftmost
80 bits only.
8. Click on the [Apply] button to accept changes.
9. If prompted, enter the Administrator’s User ID [admin] and Password [1111], and click on
[Login].
10. Click on [OK].

IPv6 Supplement
Configure IP Settings and IP Filtering4