Xiaomi Redmi Buds 4 Pro User manual

Redmi Buds 4 Pro User Manual

Read this manual carefully before use, and retain it for future reference.
Product Overview
Charging Port Function
Button
Indicator
Charging Case
Secondary
Microphone
Touch Area
Primary
Microphone
Earbud
Note: Illustrations of product, accessories, and user interface in the user manual are for
reference purposes only. Actual product and functions may vary due to product enhancements.
Package Contents
Type-C
Charging Cable
User ManualCharging Case Ear TipsEarbuds
1

Pairing
While the lid is open and both earbuds are in the
charge case, press and hold the function button
on the bottom for 2 seconds. Once the indicator
blinks white, the earbuds enter the pairing state
after releasing the button.
The rst time the lid of the charging case is opened,
the earbuds automatically enter the pairing state.
Enable the device's Bluetooth, and then search for
and connect to the "Redmi Buds 4 Pro".
Dual-Device Connection
The earbuds can be connected to two dierent Bluetooth devices simultaneously. After connecting
the earbuds to the rst device, put them in the charging case and open the lid. Press and hold the
function button on the charging case for 2 seconds, then the charging case's indicator will start
blinking white, and the earbuds are ready to be paired with a second device.
Restoring Factory Settings
While the lid is open and both earbuds are in the charging case, press and hold the function button on
the bottom for about 10 seconds. Once the indicator blinks white and the button is released, the
earbuds will restore the factory settings and enter the pairing state again.
2

S
M
L
Replacing the Ear Tips
Please change the ear tips of both earbuds
according to the noise cancellation eect and
level of comfort.
The size M ear tips are pre-installed on the
earbuds.
Gently Tap Either Earbud Twice
Music: Play/Pause
Call: Answer
Gently Tap Either Earbud Three Times
Music: Next song
Call: Reject/End call
Tap and Hold the Touch Area to Switch
Noise cancellation mode/Transparency mode
3

The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any
use of such marks by Xiaomi Inc. is under license. Other trademarks and trade names are those of their
respective owners.
Specications
Name: Wireless earphones
Model: M2132E1
HVIN: M2132E1-L, M2132E1-R
Charging Port: Type-C
Net Weight: Approx. 46 g
Impedance: 24 Ω
Operating Temperature: 5°C to 40°C
Earbud Input: 5.25 V=160 mA Max. (per earbud)
Earbud Cell Capacity/Energy: 54 mAh/0.2 Wh (per earbud)
Charging Case Cell Capacity/Energy: 590 mAh/2.28 Wh
Charging Case Input: 5 V=0.5 A Max.
Bluetooth Proles: Bluetooth®Low Energy/HFP/A2DP/AVRCP
Operating Range: 10 m (in an obstacle-free environment)
Bluetooth Operation Frequency: 2400-2483.5 MHz
Bluetooth Maximum Output Power: <13 dBm
Warnings
Do not attempt to disassemble, repair or modify the product, as this may cause fire
or even completely damage the product.
Do not expose the product to environments with a temperature that is too low or too
high (below 0°C or above 45°C).
Keep the product's indicator away from the eyes of children and animals while the
product is in use.
Do not use this product during thunderstorms. Thunderstorms may cause the product to
malfunction and increase the risk of electric shocks.
4

Avoid any contact with liquids.
Do not disassemble, puncture or crush the product nor expose it to fire.
Stop using the product immediately if there is any swelling.
Do not use the earbuds while driving, and comply with the relevant regulations in
your region or country.
These earbuds and their accessories may contain small parts. Please keep them out of
the reach of children.
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of
a battery, that
can result in an explosion.
Leaving a battery in an extremely high temperature surrounding environment that can
result in an explosion or the leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure that may result in an explosion or
the leakage of flammable liquid or gas.
Product information and certification marks are located in the charging case.
Do not put the battery in trash that is disposed of in landfills. When disposing of
the battery, comply with local laws or regulations.
Replacement of a battery with an incorrect type that can defeat a safeguard (such as
catching fire, explosion and leakage of corrosive electrolyte).
This equipment complies with RF radiation exposure limits set forth for an uncontrolled
environment.
To prevent possible hearing loss, do not use this product at high volume for long
periods of time.
Hereby, Zimi Corporation declares that the radio equipment type M2132E1 is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at the following internet address:
http://www.mi.com/global/service/support/declaration.html
EU Declaration of Conformity
5

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
IC: 26993-M2132E1
CAN ICES-3(B)/NMB-3(B)
Avoid any contact with liquids.
Do not disassemble, puncture or crush the product nor expose it to fire.
Stop using the product immediately if there is any swelling.
Do not use the earbuds while driving, and comply with the relevant regulations in
your region or country.
These earbuds and their accessories may contain small parts. Please keep them out of
the reach of children.
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of
a battery, that
can result in an explosion.
Leaving a battery in an extremely high temperature surrounding environment that can
result in an explosion or the leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure that may result in an explosion or
the leakage of flammable liquid or gas.
Product information and certification marks are located in the charging case.
Do not put the battery in trash that is disposed of in landfills. When disposing of
the battery, comply with local laws or regulations.
Replacement of a battery with an incorrect type that can defeat a safeguard (such as
catching fire, explosion and leakage of corrosive electrolyte).
This equipment complies with RF radiation exposure limits set forth for an uncontrolled
environment.
To prevent possible hearing loss, do not use this product at high volume for long
periods of time.
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in
directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead,
you should protect human health and the environment by handing over your waste
equipment to a designated collection point for the recycling of waste electrical and
electronic equipment, appointed by the government or local authorities. Correct disposal
and recycling will help prevent potential negative consequences to the environment and
human health. Please contact the installer or local authorities for more information about
the location as well as terms and conditions of such collection points.
WEEE Information
Hereby, Zimi Corporation declares that the radio equipment type M2132E1 is in
compliance with Radio Equipment Regulations 2017. The full text of the UK declaration
of conformity is available at the following internet address: https://www.mi.com/uk/-
service/support/declaration.html
UK Declaration of Conformity
6

This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled
environment. End user must follow the specic operating instructions for satisfying RF exposure
compliance. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established
by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The
highest SAR value reported under this standard during product certication for use when properly
worn on the body.
Manufactured for: Xiaomi Communications Co., Ltd.
Manufactured by: Zimi Corporation
Address: A913, No. 159 Chengjiang Road, Jiangyin, Jiangsu, China
For further information, please go to www.mi.com
User Manual Version: V1.0
Importer:
Beryko s.r.o.
Pod Vinicemi 931/2, 301 00 Plzeň
www.beryko.cz
7