Xinje TS Series User manual

TS series HMI manual
[Hardware]
Wuxi Xinje Electric Co., Ltd.
Data No. HSC01 20220428EN 1.0

Basic description
Thank you for purchasing the Xinje TS series HMI.
This manual mainly introduces the hardware characteristics of TS series HMI.
Before using the product, please read this manual carefully and conduct wiring on the premise of fully
understanding the contents of the manual.
Please refer to relevant manuals for introduction to software and programming.
Please deliver this manual to the end user.
Notice to users
Only operators with certain electrical knowledge can perform other operations such as wiring on the
product. If there is any unknown place, please consult our technicians.
The examples listed in the manual and other technical materials are only for users' understanding and
reference, and do not guarantee certain actions.
When using this product in combination with other products, please confirm whether it conforms to
relevant specifications, principles, etc.
When using this product, please confirm whether it meets the requirements and is safe.
Please set the backup and safety functions by yourself to avoid possible machine failure or loss caused by
the failure of this product.
Please avoid using HMI in the environment of high radiation and strong magnetic field to avoid
interference.
Declaration of responsibility
Although the contents in the manual have been carefully checked, errors are inevitable, and we cannot
guarantee that they are completely consistent.
We will often check the contents of the manual and make corrections in subsequent versions. Please give
us your valuable suggestions.
The contents described in the manual are subject to change without notice.
Contact us
Headquarters address: No. 816, Jianzhu West Road, Binhu District, Wuxi City, Jiangsu Province, China
Service hotline: 400-885-0136
Tel: 0510-85134136
Fax: 0510-85111290
Website: www.xinje.com

WUXI XINJE ELECTRIC CO., LTD. All rights reserved
Without explicit written permission, this material and its contents shall not be copied, transferred or used.
Violators shall be liable for the losses caused.All rights provided in patent license and registration,
including utility modules or designs, are reserved.
Nov. 2021


i
CATALOG
1. TS3 SERIES HMI OVERVIEW .................................................................................................................................1
1-1. PRODUCT FEATURES...............................................................................................................................................1
1-1-1. Product features...............................................................................................................................................1
1-1-2. Naming rule.....................................................................................................................................................2
1-1-3. Model list.........................................................................................................................................................2
1-2. PRODUCT SPECIFICATION..........................................................................................................................................2
1-3. PART DESCRIPTION ...................................................................................................................................................3
1-3-1. Structure description........................................................................................................................................3
1-3-2. Interface description........................................................................................................................................4
1-4. PRODUCT DIMENSION AND INSTALLATION ................................................................................................................7
1-4-1. Product dimension...........................................................................................................................................7
1-4-2. Product installation and use environment........................................................................................................8
2. TS5L SERIES HMI OVERVIEW...............................................................................................................................1
2-1. PRODUCT FEATURES.................................................................................................................................................1
2-1-1. Product features...............................................................................................................................................1
2-1-2. Naming rule.....................................................................................................................................................2
2-1-3. Model list.........................................................................................................................................................2
2-2. PRODUCT SPECIFICATION..........................................................................................................................................2
2-3. PART DESCRIPTION ...................................................................................................................................................3
2-3-1. Structure description........................................................................................................................................3
2-3-2. Interface description........................................................................................................................................4
2-4. PRODUCT DIMENSION AND INSTALLATION ................................................................................................................7
2-4-1. Product dimension...........................................................................................................................................7
2-4-2. Module installation..........................................................................................................................................8
2-4-3. Product installation and using environment ..................................................................................................10


1
1. TS3 series HMI overview
1-1. Product features
◆16.77 million colors TFT-LCD, highlighted screen, full color, more realistic display effect.
◆High speed A8 600MHz main frequency CPU, 128MB memory, excellent data processing ability,
faster download speed and large. Greatly improve the boot loading speed, reduce the waiting time and
screen jump, and the animation effect is better and smooth.
◆Dimensions include 7’’ and 10.1’’.
◆Ultra thin body, fashionable appearance, installation bayonet and back sealing, effectively preventing
the entry of external dust, oil stain, etc.
◆The standard USB interface supports the connection of USB devices such as mouse, keyboard and
code scanning gun.
◆The communication capability is upgraded. It can communicate with multiple PLCs at the same time.
RJ45 Ethernet interface supports the communication with TBOX and Siemens S7-1200, S7-200 Smart
and other Modbus TCP devices, break the traditional serial communication mode and form an open
network structure.
1-1-1. Product features
(1) Display
◆16.77 million color display, supporting BMP and JPEG format pictures, with richer colors and more
realistic display effect.
◆Touch calibration function.
◆128MB large memory is used to realize high-speed downloading, high-speed loading and high-speed
operation.
◆The storage capacity is greatly increased.
◆Support Chinese, English, Japanese, Korean and other languages, set fonts at will, size as you want,
support underline, italic, bold, etc., and set shadow, three-dimensional, stroke and other artistic
effects.
◆Abundant picture materials, and the screen operation is free of stagnation.
(2) Control
◆Switch control, data dynamic display monitoring, bar chart, data trend chart, XY trend chart, XY line
chart, pie chart, alarm record, operation record and other control functions.
◆Data collection and saving of user-defined conditions.
◆User permission setting and multi-level password protection mechanism.
◆Online simulation, offline simulation and data upload.
◆Powerful function block of C language, including operation, command and communication.
◆USB flash disk data backup function of USB-A (USB2.0 standard) interface, with a speed up to
480Mbps, can be connected to mouse, keyboard, code scanning gun and other USB port devices.
◆USB-B (USB2.0 standard) download interface makes data transmission faster.
◆Customized animation track design.
◆It covers all functions of TG series.
◆Multiple download methods.

2
(3) Communication
◆Dual port independent communication, which can connect multiple different devices at the same time.
◆-E series is equipped with Ethernet interface to support communication with Ethernet equipment,
Siemens S7-1200, Siemens S7-200 Smart and other Modbus TCP equipment.
◆The printer can be directly driven, which is economical and flexible.
◆Support free format communication, and end users can write drivers freely.
1-1-2. Naming rule
①③
②
700
TS3 E
①:
Series
TS3 series
②:
Display
700:7.0 inch
1000:10.1 inch
③:
Interface
M:USB-B, USB-A, COM1, COM2
E:USB-B, USB-A, RJ45, COM1, COM2
1-1-3. Model list
Xinje TS3 series HMI have the following models according to different display sizes and function types:
Display
7〞
10.1〞
General model
TS3-700-M
TS3-700-E
TS3-1000-M
TS3-1000-E
1-2. Product specification
Product model
TS3-700
TS3-1000
Product
features
Size
7.0”
10.1”
Resolution
800*480
1024*600
LCD
TFT LCD display, LED
Display colors
16.77 million colors
Brightness
200 cd/m2
Touch panel
Four wire resistive touch screen
LCD life
More than 50000 hours, ambient temperature 25℃, 24-hour operation
Processor
Cortex-A8 600MHz
Storage
128MB
Interface
COM1
RS232/RS485
COM2
RS232/RS485/RS422
USB-A port
Flash disk port, USB2.0
USB-B port
USB download port, USB2.0
Ethernet port
Standard RJ45 (10/100M self-adaption), -E models support
Electrical
characteristics
Input voltage
DC24V (voltage range: DC22V-DC26V)
Current
consumption
200mA
270mA
Allowable
power loss
Below 10ms (the actual power loss is less than 1s)

3
Product model
TS3-700
TS3-1000
Voltage impact
resistance
AC1000V, 10mA, less than 1 minute (signal and ground)
Insulation
resistance
Above 10MΩ, DC500V
Environment
Operation
temperature
0-50℃
Storage
temperature
-10-60℃
Operation
humidity
10%RH-90%RH (no condensation)
Anti
interference
capability
Voltage noise: 1500Vp-p, pulse width 1us, 1 minute
Air
No corrosive gas
Cooling
method
Natural air cooling
Protection
Front cover IP65
Dimension
Display area
154.08*85.92 mm
219.6*131.76 mm
Product
dimension
206.0*147.0*35.0 mm
277.0*191.7*36.6 mm
Opening
dimension
192.3*138.6 (±0.5) mm
260.2*179.7 (±0.5) mm
【Note】: Flash has a lifetime of 100000 erasures.
1-3. Part description
1-3-1. Structure description
The following figure shows the reverse area of TS3 HMI. For specific model and appearance, please refer to the
chapter "1-4 Product Dimensions and Installation".
Labels
Power supply
COM1
COM2
USB-B port
Dial switch
USB-A port
RJ45 port

4
1-3-2. Interface description
The HMI of Xinje TS3 series is described as follows:
Appearance
Name
Function
1 2 3 4
1 2 3 4
Dial switch
Used to set forced download, touch calibration, etc
Download
COM1
COM1
Support RS232/RS485 communication
PLC
COM2
COM2
Support RS232/RS485/RS422 communication
USB-A port
USB flash disk can be inserted to store data, and USB
flash disk can be imported into the project
USB-B port
Connect USB cable to upload/download program
Ethernet port
Support communication with TBOX, Siemens S7-1200,
Siemens S7-200 Smart and other Modbus TCP devices
1. Dial switch
TS3 series HMI has a set of 4-bit dial switches, which are located at the bottom right of the back. Its setting
functions are as follows:
Switch
DIP1
DIP2
DIP3
DIP4
Function
Status
ON
OFF
OFF
OFF
Undefined
OFF
ON
OFF
OFF
USB flash disk import program
OFF
OFF
ON
OFF
Touch screen calibration
OFF
OFF
OFF
ON
Undefined
2. Communication port
(1) COM1 port pins definition
Pin
Name
Explanation
1
NC
Null signal pin
2
RXD
RS232 communication receive data
3
TXD
RS232 communication send data
4
A
RS485 communication signal +
5
GND
Signal ground
6
NC
Null signal pin
7
B
RS485 communication signal -
8
NC
Null signal pin
9
NC
Null signal pin

5
(2) COM2 port pins definition
Pin
Definition
Explanation
1
TD+
RS422 communication send +
2
RXD
RS232 communication receive data
3
TXD
RS232 communication send data
4
A
RS485 communication signal +
5
GND
Signal ground
6
TD-
RS422 communication send -
7
B
RS485 communication signal -
8
RDD-
RS422 communication receive -
9
RDD+
RS422 communication receive +
3. USB-A interface
TS3 series HMI is equipped with one USB-A (USB2.0 specification) port as standard, which has the following
functions: realize backup management, complete data import and export functions, and the transmission rate
reaches 480Mbps.
Pin
Definition
Explanation
1
+5V
+5V voltage signal
2
DATA+
Data + signal
3
DATA-
Data - signal
4
-5V
-5V voltage signal (ground signal)
4. USB-B port
TS3 series HMI has a USB-B (USB2.0 specification) port, which is located on the upper right side of the
reverse side, and realizes the following functions: data download function, and the transmission rate reaches
480Mbps.
Pin
Definition
Explanation
1
+5V
+5V voltage signal
2
DATA-
Data + signal
3
DATA+
Data - signal
4
GND
Signal ground
(1) Please use the shielded USB cable.
(2) The TouchWin Pro editing tool and USB drive must be correctly installed before using.
(3) After the drive is correctly installed, confirm that the computer is correctly connected to the TS3 series
HMI, click to download HMI program.

6
5. RJ45 port
RJ45 port pin definition:
1
8
Pin
Color
Definition
Explanation
1
Orange
white
TXD+
Data send +
2
Orange
TXD-
Data send -
3
Green white
RXD+
Data receive +
4
Blue
-
-
5
Blue white
-
-
6
Green
RXD-
Data receive -
7
Brown
white
-
-
8
Brown
-
-

7
1-4. Product dimension and installation
1-4-1. Product dimension
◼TS3-700 (unit: mm)
35
190.3
147
136.6
206
138.6±0.5
192.3±0.5
◼TS3-1000 (unit: mm)
258.2
177.7
37.5
8.6
177.6
277.0
191.7
260.2±0.1
179.7±0.1

8
1-4-2. Product installation and use environment
1. Installation requirement
TS3 series HMI is equipped with four iron mounting brackets at the factory. The upper and lower sides of the
display are respectively provided with two square fixing holes. The display is tightly fixed to the mounting holes
of the control cabinet with the mounting bracket.
In order not to cause the temperature of the HMI to be too high when working for a long time, it is better to
reserve 10cm space above and below the HMI and 5cm space left and right during installation to ensure smooth
air convection.
2. Installation steps
(1) According to the dimensions in the previous section, open a rectangular mounting hole on the panel of the
control cabinet.
(2) During installation, a sealing ring is added in the sealing groove.
(3) Insert the bottom of the display into the mounting hole of the control cabinet.
(4) Insert the mounting bracket into the side fixing hole of the display and tighten the screws.
(5) Connect the HMI and PLC communication port with communication cable.
The communication cable can be provided by the manufacturer or processed by the user according to the
connection diagram, and can start to work after being connected to the +24V DC power supply.
3. Environmental factor
Please install and use correctly within the specified environment.
【Note】: Do not use it in a dangerous environment full of flammable gas, water vapor or dust, and do not install it in an
environment where the temperature changes too fast or the humidity is high, otherwise it will cause moisture
condensation inside the HMI.
4. Power supply requirement
TS3 series HMI can only use DC power supply. The power supply specification is DC+24V (voltage range:
22V~26V), which conforms to the standard of DC power supply for most industrial control equipment. Connect
the positive pole of the DC power supply to the "+24V" terminal and the negative pole of the DC power supply to
the "0V" terminal. As shown in the figure below:
In addition, connecting high voltage or alternating current to the power input terminal in the HMI will make the
equipment unusable and may cause electric shock to the human body. Such mistakes or serious electric shock can
lead to personal injury, even death, and equipment damage.
【Note】:
If the PLC DC output is used to drive the HMI, it must be considered that the +24V DC output of some controllers may
not have enough current to support it.
+DC-
0 V
+24V

1
2. TS5L series HMI overview
2-1. Product features
◆16.77 million colors TFT-LCD, highlighted screen, full color, more realistic display effect.
◆High speed A8 600MHz main frequency CPU, 128MB memory, excellent data processing ability,
faster download speed and large. Greatly improve the boot loading speed, reduce the waiting time and
screen jump, and the animation effect is better and smooth.
◆Dimensions include 7’’ and 10.1’’.
◆Ultra thin body, fashionable appearance, installation bayonet and back sealing, effectively preventing
the entry of external dust, oil stain, etc.
◆The standard USB interface supports the connection of USB devices such as mouse, keyboard and
code scanning gun.
◆Standard 3.5mm audio interface, supporting sound output.
◆The communication capability is upgraded. It can communicate with multiple PLCs at the same time.
RJ45 Ethernet interface supports the communication with TBOX and Siemens S7-1200, S7-200 Smart
and other Modbus TCP devices, break the traditional serial communication mode and form an open
network structure.
◆WIFI/4G modules are optional.
2-1-1. Product features
(1) Display
◆16.77 million color display, supporting BMP and JPEG format pictures, with richer colors and more
realistic display effect.
◆Touch calibration function.
◆128MB large memory is used to realize high-speed downloading, high-speed loading and high-speed
operation.
◆The storage capacity is greatly increased.
◆Support Chinese, English, Japanese, Korean and other languages, set fonts at will, size as you want,
support underline, italic, bold, etc., and set shadow, three-dimensional, stroke and other artistic
effects.
◆Abundant picture materials, and the screen operation is free of stagnation.
(2) Control
◆Switch control, data dynamic display monitoring, bar chart, data trend chart, XY trend chart, XY line
chart, pie chart, alarm record, operation record and other control functions.
◆Data collection and saving of user-defined conditions.
◆User permission setting and multi-level password protection mechanism.
◆Online simulation, offline simulation and data upload.
◆Powerful function block of C language, including operation, command and communication.
◆USB flash disk data backup function of USB-A (USB2.0 standard) interface, with a speed up to
480Mbps, can be connected to mouse, keyboard, code scanning gun and other USB port devices.
◆USB-B (USB2.0 standard) download interface makes data transmission faster.
◆Customized animation track design.
◆It covers all functions of TG series.
◆Multiple download methods.

2
(3) Communication
◆Dual port independent communication, which can connect multiple different devices at the same time.
◆Equipped with Ethernet interface to support communication with Ethernet equipment, Siemens
S7-1200, Siemens S7-200 Smart and other Modbus TCPequipment.
◆The printer can be directly driven, which is economical and flexible.
◆Support free format communication, and end users can write drivers freely.
◆Covering mainstream information interaction protocols and support MQTT/TCP IP communication.
2-1-2. Naming rule
700
TS5L M
①:
Series
TS5L series
②:
Size
700: 7.0 inch
1000: 10.1 inch
③:
Module
type
M: no module
E: no module, with Ethernet port
G: with 4G module
W: with WIFI module
2-1-3. Model list
Xinje TS5L series HMI has the following models according to different display sizes and function types:
Display size
7〞
10.1〞
General type
TS5L-700
TS5L-700-E
TS5L-700-4G
TS5L-700-W
TS5L-1000
TS5L-1000-E
TS5L-1000-4G
TS5L-1000-W
2-2. Product specification
Product model
TS5L-700
TS5L-1000
Features
Size
7.0”
10.1”
Resolution
800*480
1024*600
LCD
TFT LCD display, LED backlight
Display color
16.77 million colors
Brightness
200 cd/m2
Touch panel
Four wire resistive touch screen
LCD life
More than 50000 hours, ambient temperature 25℃, 24-hour operation
Processor
Cortex-A8 600MHz
Storage
128MB
Interface
COM1
RS232/RS485
COM2
RS232/RS485/RS422
USB-A port
USB flash disk port, USB2.0
USB-B port
USB download port, USB2.0

3
Product model
TS5L-700
TS5L-1000
Ethernet port
Standard RJ45 (10/100M self-adpation)
Audio interface
ɸ3.5 coaxial audio plug
4G (optional)
4G
LTE-FDD (Mbps): 10 (downlink) / 5 (uplink)
WIFI (optional)
IEEE 802.11 a/b/g/n
IEEE 802.11 g: 54Mbps
Electric
features
Input voltage
DC24V (voltage range: DC22V-DC26V)
Current
consumption
200mA
270mA
Allowable
power loss
Below 10ms (the actual power loss is less than 1s)
Voltage impact
resistance
AC1000V, 10mA, less than 1 minute (signal and ground)
Insulation
resistance
Above 10MΩ, DC500V
Environment
Operation
temperature
0-50℃
Storage
temperature
-10-60℃
Operation
humidity
10%RH-90%RH (no condensation)
Anti
interference
capability
Voltage noise: 1500Vp-p, pulse width 1us, 1 minute
Air
No corrosive gas
Cooling
method
Natural air cooling
Protection
Front cover IP65
Dimension
Display area
154.08*85.92 mm
219.6*131.76 mm
Product
dimension
205.8*147.2*35.5 mm
277.0*191.7*37.6 mm
Opening
dimension
192.1*138.5 mm (±0.1)
260.2*179.7 mm (±0.1)
【Note】: Flash rewriting life is 100000 times.
2-3. Part description
2-3-1. Structure description
The following figure shows the reverse area of TS5L HMI. For specific model and appearance, please refer to
the chapter "1-4 Product Dimensions and Installation":

4
2-3-2. Interface description
The HMI of Xinje TS5L series is described as follows:
Appearance
Name
Function
1 2 3 4
1 2 3 4
Dial switch
Used to set forced download, touch calibration, etc
Download
COM1
COM1
Support RS232/RS485 communication
PLC
COM2
COM2
Support RS232/RS485/RS422 communication
USB-A port
USB flash disk can be inserted to store data, and USB
flash disk can be imported into the project
USB-B port
Connect USB cable to upload/download program
Ethernet port
Support communication with TBOX, Siemens S7-1200,
Siemens S7-200 Smart and other Modbus TCP devices
Audio interface
ɸ3.5 coaxial audio plug, supporting the connection of
speakers for sound output
1. Dial switch
The TS5L series HMI has a set of 4-bit dial switches, which are located at the bottom right of the back. The
Label
Power supply
COM1
COM
2
USB-B port
Dial switch
USB-A port
RJ45 port
Audio
interface
Antenna
interface
Expansion
module

5
setting functions are as follows:
Switch
DIP1
DIP2
DIP3
DIP4
Function
Status
ON
OFF
OFF
OFF
Undefined
OFF
ON
OFF
OFF
USB flash disk import program
OFF
OFF
ON
OFF
Touch calibration
OFF
OFF
OFF
ON
Undefined
2. Communication port
(1) COM1 port pin definition:
Pin
Name
Explanation
1
NC
Null signal
2
RXD
RS232 communication receive data
3
TXD
RS232 communication send data
4
A
RS485 communication signal +
5
GND
Signal ground
6
NC
Null signal
7
B
RS485 communication signal -
8
NC
Null signal
9
NC
Null signal
(2) COM2 port pin definition:
Pin
Name
Explanation
1
TD+
RS422 communication send +
2
RXD
RS232 communication receive data
3
TXD
RS232 communication send data
4
A
RS485 communication signal +
Pin
Name
Explanation
5
GND
Signal ground
6
TD-
RS422 communication send -
7
B
RS485 communication signal -
8
RDD-
RS422 communication receive -
9
RDD+
RS422 communication receive +
3. USB-A port
TS5L series HMI is equipped with one USB-A (USB2.0) port as standard, which has the following functions:
realize backup management, complete data import and export functions, and the transmission rate reaches
480Mbps.
Pin
Definition
Explanation
1
+5V
+5V voltage signal
2
DATA+
Data﹢signal
3
DATA-
Data﹣signal
4
-5V
-5V voltage signal (ground signal)
4. USB-B port
TS5L series HMI has a USB-B (USB2.0) port, which is located on the upper right side of the reverse side and
realizes the following functions: data download function, transmission rate up to 480Mbps.

6
Pin
Definition
Explanation
1
+5V
+5V voltage signal
2
DATA-
Data﹢signal
3
DATA+
Data﹣signal
4
GND
Signal ground
(1) Please use the shielded USB cable
(2) The TouchWin Pro editing tool and USB drive must be correctly installed before using.
(3) After the drive is correctly installed, confirm that the computer is correctly connected to the TS5L series
HMI, click to download HMI program.
5. RJ45 port
RJ45 port pin definition:
1
8
Pin
Color
Definition
Explanation
1
Orange
white
TXD+
Data send +
2
Orange
TXD-
Data send -
3
Green white
RXD+
Data receive +
4
Blue
-
-
5
Blue white
-
-
6
Green
RXD-
Data receive -
7
Brown
white
-
-
8
Brown
-
-
This manual suits for next models
10
Table of contents
Other Xinje Touch Panel manuals