Xpand RF PRO AE125-RF User manual

to be used on dark background to be used on light background
XPAND RF PRO
EMITTER SYSTEM
AE125-RF User Guide

© XPAND, All Rights Reserved. www.xpandvision.com
XPAND RF PRO Emitter System
XPAND 3D RF emitter system generates the signal that synchronizes XPAND 3D
RF glasses with digital projector.
The system consists of:
»1x RF PRO Emitter (AE125-RF)
»1x 3D-VESA to BNC sync cable (CAB-01-0301)
»1x 12VDC power adapter + 4x interchangeable plug (EU, US, UK, AU)
»1x User manual
»1x Warranty sheet
Emitter Overview
Power LED: Green color. Represents the power LED. When lit power is ON.
Power Connector: 12VDC
»Reverse Push-button: RF sync signal can be reversed with suppressed
push-button.
Sync Connector: BNC synchronization signal connector input.
»Sync LED: Yellow color. When OFF there is no sync signal present. When sync
signal is present LED will be ON and it will blink according to sync signal
frequency.
1
2
3
4
5

© XPAND, All Rights Reserved. www.xpandvision.com
Installation
1. Connect 12VDC power adapter to AC power outlet; use one of the included
interchangeable plugs that is appropriate for your region.
2. Insert power adapter’s output plug into RF PRO’s power connector . RF PRO
will turn on automatically and will be in stand-by mode; green LED will light
up.
3. Use included sync cable to connect your projector’s 3D-VESA (MINI-DIN-3
female) sync output connector to RF PRO’s sync connector . If your projector
has a different 3D sync output connector please consult with our XPAND technical
support team.
Positioning and Mounting
»RF PRO will emit RF sync signal omnidirectionally (meaning that it emits to all
directions), but for best performance point the front of the emitter in direction
where 3D glasses will be used.
»Range might drop if there will be any obstacles between 3D emitter and 3D
glasses.
»Emitter has four rubber feet so it can be securely placed on a at surface.
»For maximum range emitter should be raised off ground or lowered from
celling for at least 30 cm / 1 ft.
»Emitter is equipped with mounting hole which can be used with XPAND’s
Wall Mount (sold separately). When used label should be pierced with sharp
object where it says “Mounting Hole”.
1
2
4
6

User Interface
Power LED
Power LED will indicate that emitter is powered and running.
Sync LED
Sync LED will not only show whether synchronization signal from projector is
present or not. User can also check the functionality of glasses looking at LED
through left or right lens; through one it should be bright, through other it should
be dim.
Push-button
Reverse Push-button is used to reverse RF sync signal. Although this can be
achieved in projector’s setting, it is more convenient to do this on emitter itself
where the user can check the picture with 3D glasses right on the spot.
Troubleshooting
Emitter is connected but 3D glasses do not work:
»Make sure power adapter is connected properly. Power LED should be lit.
»Make sure sync cable is connected properly and that projector is in 3D mode.
Sync LED should be lit.
»Make sure that your 3D glasses have been successfully paired with the emitter
and that they are turned ON. Refer to your 3D glasses’ manual for instructions
on how to pair them with new emitter.
© XPAND, All Rights Reserved. www.xpandvision.com
1
5
3
1
5

Technical Specications
Type of Synchronization: Radio Frequency (RF)
3D Sync Protocol In: VESA Stereo
3D Sync Protocol Out: FHD3D RF protocol
Shuttering Frequency: 96 Hz, 100 Hz, 120 Hz, 144 Hz, 192 Hz and 240 Hz
High Frame Rate (HFR): Yes
Reverse Sync function: Yes (button)
Memory: No memory inside
USER Interface:
»Power LED
»Sync LED
»Reverse Sync Button
Mounting Option:
»Rubberized feet for positioning on a at surface
»Mounting hole for wall mount (mount supplied separately)
Sync Connector Type: female BNC
Power Connector Type: 5,5 × 2,1 mm socket
Coverage Range:
»Operating/Sync distance: approx. 20 m / 66 ft (approx. 10 m / 33 ft if on
ground)
»Pairing distance: up to 7 m / 23 ft
Setup: Plug&Play
Sync Cable: male mini-DIN-3 (VESA Stereo) to male BNC; 2 m / 6.5 ft long
Power: 12VDC power adapter; 1,4 m / 4.5 ft long – EU, USA, UK and AU plug
adapters included
Operating Temperature: 5 °C – 40 °C / 41 °F – 104 °F
Dimensions and weight: 115 × 76 × 36 mm, 126 g / 4.5 × 3 × 1.4 in, 4.4 oz
© XPAND, All Rights Reserved. www.xpandvision.com

Important Safety Instructions
»Read these instructions.
»Keep these instructions.
»Heed all warnings.
»Follow all instructions.
»Do not use this apparatus near water.
»Clean only with dry cloth.
»Only use the attachments/accessories specied by the manufacturer.
to be used on dark background to be used on light background

AE125-RF_M_eng_01