XROCKER Elite Pro User manual

User Manual Item no: 5150201
Need Help? Email: Service@XRockerNaon.co.uk
Phone: [phone] www.XRockerNaon.co.uk
IMPORTANT: You must keep your original retail receipt as proof of purchase.
Elite Pro

2
Thank you for purchasing this X Rocker gaming
chair. You are now close to enhancing your
favourite games with glorious audio!
To get started, please assemble the chair using
the assembly instrucons on the separate leaet
and then follow the instrucons in this manual to
get rocking!
Table of contents
2 Box contents and control panel overview
4 Wireless connecon guide: TV (All consoles)
5 Wired connecon guide: TV (All consoles)
6 Connect by controller (PS4 systems only)
7 Bluetooth connecon guide:
(Mobile phones/tablet devices)
8 Troubleshoong ps
9 Health and safety informaon
10 Power supply safety informaon
Welcome to X Rocker!

3
+
+
+ +
+
+
Control panel overview
B1 - 3m RCA to RCA Audio cable
B2 - 1m 3.5mm to 3.5mm Audio cable
B3 - RCA female to female adapters
B4 - 15cm RCA to 3.5mm audio cable
B5 – 15cm 3.5mm to 3.5mm audio cable
B6 – Power Supply Cable
B7 – Wireless Transmier
9.84/3m 3.28/1m
0.492/0.15m
0.492/0.15m
B
B1
B3
B5 B6
B4
B2
+B7

4
To connect using the wireless transmier, connect the Wireless
transmier (B7) to your TV set using the 3.5mm to 3.5mm cable (B2/B5)
Once connected, Set the control panel on the chair and the Wireless
transmier to the same band (1,2,3)
To get the best sound, make sure that the volume on the TV is set to
approximately 50% of the maximum. Depending on the TV you may need
to set the volume level separately in the TV sound sengs menu. (Please
refer to TV manual for guidelines.)
Wireless connecon guide: TV
(All consoles)
B5
TV/Mobile/Tablet

5
1. Connect B1 Cable to X Rocker control panel RCA INPUT sockets
2. Connect B3 RCA adapters to other end of B1 RCA cable
3. Connect B4 RCA cable to B3 Adapter.
4. Connect B4 3.5mm end into the headphone socket of your Television
5. Once connected to your TV, increase volume to 50% of the maximum
for the best sound level.**
*N.B: If your TV does not feature a headphone socket then you may need
to purchase an addional TOSlink adapter to get connected directly to a
console for audio. Contact support for more details.
**Depending on your TV you may need to Increase the headphone
volume separately in the TV sound sengs.
Wired connecon guide: TV
(All consoles)
TV/Mobile/Tablet
B4

6
1. Connect the B2 cable to the boom of the PS4 controller via the
headset socket.
2. Connect the other end of the B cable to the chair via the green port.
3. With the PS4 turned on, go to the main menu (or locate the main
menu screen). Press and hold the PS buon on the PS4 controller unl
the quick menu appears on screen.
4. In this menu select [Adjust sound and devices]
5. Then select [output to headphones]
6. Change the seng from [Chat Only] to [All audio]
7. Make sure the volume in the previous menu is set to the maximum.
8. Set the control panel Wireless switch to the ‘OFF’ posion.
Connect by controller:
(PS4 systems only)
B2

7
Step 1:
Switch the X Rocker Elite Pro’s wireless switch to the Bluetooth posion.
Step 2:
On the Audio output device
go into its Bluetooth sengs,
turn Bluetooth on if it is not
on already and search for
XROCKER. Upon nding this,
select the XROCKER opon.
If a passcode is required the four
digit code will be ‘0000’.
Bluetooth connecon guide:
(Mobile phones/tablet devices)

8
Troubleshoong ps
• Make sure that the power cable is
connected correctly.
• Make sure that the power supply at the
power source is working correctly.
• With the chair turned to the ON posion,
give the power cable a slight wiggle in the
port. If any lights icker (or not)
then please contact support (details below).
• Review the connecon methods on
the previous page and try alternave
connecon methods if possible.
• Conrm that the device/system is
correctly congured as per previous
connecon guide.
• Make sure that the wireless channel
switcher is in the corresponding posion
that suits your connecon method.
(1,2,3 for wireless and AUX for wired
connecons).
• Please make sure that the volume of
the source device is at a higher level to
strengthen the audio signal.
• Please contact X Rocker support
(service@XRockerNaon.co.uk) regarding
this issue.
• In this case, try another of the three
wireless bands to isolate the signal.
No power going to control panel
Issue Troubleshoong steps
No sound
Wireless transmier cuts out during
gameplay/No vibraon or subwoofer
sound via analogue connecon
The cables connected to my
X Rocker have been broken
accidentally
Interference over wireless connecon

9
Health and safety informaon
• Avoid immersing or allowing the X Rocker to come into contact
with liquids.
• Please consult X Rocker Support before unscrewing any of the electrical
components on the chair.
• Please be mindful of any cabling laid out between the X Rocker and
power source/audio device.
• Please be mindful of cabling aached when moving/swivelling
the X Rocker.
• If the cables or electrical equipment are broken then this may present
a choking risk, please contact Support for replacements and dispose of
these parts safely.
• Do not stand on the X Rocker or exceed the 120kg weight limit via
other means.
• Do not lean back on the chair to the point in which the pedestal would
li o the ground.
• X Rocker armrests are designed for support and comfort during
gameplay, please do not use these as support for geng in/out of
the chair.
• Playing audio for long periods at loud volumes may contribute to
dicules in hearing.
• Please be considerate to others when playing audio through the
X Rocker speakers at higher volumes.

10
Power supply safety informaon