Xsens MTi 600 Series Quick setup guide

Xsens Technologies B.V.
Xsens North America, Inc.
Pantheon 6a
P.O. Box 559
7500 AN Enschede
The Netherlands
phone [phone]
fax [phone]
e-mail [e-mail]
internet www.xsens.com
101 N. Pacific Coast Hwy
Suite 101
El Segundo, CA 90245
USA
phone [phone]
fax [phone]
e-mail [e-mail]
internet www.xsens.com
Document MT1601P, Revision A, 9 sept 2019
MTi 600-series
Hardware Integration Manual

www.xsens.com
ii
Document MT1601P.A
© Xsens Technologies B.V.
Hardware Integration Manual MTi 600-series
Revisions
Revision
Date
By
Changes
A
9 sept 2019
RGI
Initial release
© 2005-2018, Xsens Technologies B.V. All rights reserved. Information in this document is subject to
change without notice. Xsens, MVN, MotionGrid, MTi, MTx and Awinda are registered trademarks or
trademarks of Xsens Technologies B.V. and/or its parent, subsidiaries and/or affiliates in The
Netherlands, the USA and/or other countries. All other trademarks are the property of their respective
owners.

www.xsens.com
iii
Document MT1601P.A
© Xsens Technologies B.V.
Hardware Integration Manual MTi 600-series
Table of Contents
1GENERAL INFORMATION ................................................................................................................... 1
2INTERFACES ...................................................................................................................................... 2
2.1 PIN CONFIGURATION .......................................................................................................................... 2
2.2 COMMUNICATION TO HOST .................................................................................................................. 3
2.2.1 CAN..................................................................................................................................... 3
2.2.2 RS232 .................................................................................................................................. 3
2.2.3 UART ................................................................................................................................... 4
2.3 GNSS RECEIVER INTERFACE .................................................................................................................. 4
2.4 SYNC ............................................................................................................................................ 5
3ELECTRICAL SPECIFICATIONS.............................................................................................................. 6
3.1 SUPPLY VOLTAGE ............................................................................................................................... 6
3.2 POWER CONSUMPTION ....................................................................................................................... 6
3.3 I/O PINS ......................................................................................................................................... 6
4DESIGN............................................................................................................................................. 8
4.1 SENSOR REFERENCE FRAMES ................................................................................................................. 8
4.2 ORIGIN OF ACCELEROMETER ................................................................................................................. 8
4.3 PHYSICAL CONNECTIONS ...................................................................................................................... 9
4.3.1 Footprint for PCB layout........................................................................................................ 9
4.3.2 Footprint for standalone mounting ...................................................................................... 10
4.4 MECHANICAL STRESS ........................................................................................................................ 11
4.4.1 Vibrations .......................................................................................................................... 11
4.5 MAGNETOMETER ............................................................................................................................ 11
4.5.1 Ferromagnetic materials ..................................................................................................... 11
4.5.2 High currents ..................................................................................................................... 11
5PACKAGING INFORMATION............................................................................................................. 13

www.xsens.com
iv
Document MT1601P.A
© Xsens Technologies B.V.
Hardware Integration Manual MTi 600-series
List of Tables
Table 1: MTi product documentation overview ............................................................................................ 1
Table 2: Pin descriptions ............................................................................................................................. 2
Table 3: Host communication interfaces specifications.................................................................................. 3
Table 4: GNSS receiver interface specifications ............................................................................................. 4
Table 5: Supply voltage specifications .......................................................................................................... 6
Table 6: Power consumption specifications .................................................................................................. 6
Table 7: I/O interface specifications............................................................................................................. 6
Table 8: Recommended mating/mounting parts ......................................................................................... 10
Table 9: Recommended mating/mounting parts ......................................................................................... 11
List of Figures
Figure 1: Pin configuration of the MTi-600 ................................................................................................... 2
Figure 2: Connections for the GNSS interface ............................................................................................... 5
Figure 3: Default sensor coordinate system for the MTi 600-series module .................................................... 8
Figure 4: Location origin of measurements (dimensions in mm)..................................................................... 8
Figure 5: Connection options (left: PCB, right: standalone, dimensions in mm) ............................................... 9
Figure 6: Layout footprint example (dimensions in mm) ................................................................................ 9
Figure 7: Standalone mounting hole positions (dimensions in mm) .............................................................. 10

www.xsens.com
1
Document MT1601P.A
© Xsens Technologies B.V.
Hardware Integration Manual MTi 600-series
1 General information
This document provides hardware design instructions for the MTi 600-series module (MTi-600). The
MTi-600 is a fully functional, self-contained module that is easy to design-in with limited external
hardware components to be added. The MTi-600 can be embedded in an application by mounting it
directly on a PCB or as a standalone module by connecting it via a flat-ribbon cable. The MTi-600 can
be connected to a host through RS232, CAN or UART interfaces.
The MTi 600-series Datasheet1provides information on the usage and technical details of the MTi
600-series modules. The MTi 600-series module (MTi-600) is a fully functional, self-contained module
that is easy to design-in. The MTi-600 module can be connected to a host through RS232, CAN or
UART interfaces, or through USB using the UART to USB converter (included in the MTi 600-series
Development Kit).
The MTi Family Reference Manual1supplements this document. It reports generic information on the
MTi 1-series and MTi 600-series, such as output definitions, algorithm details and installation tips.
For testing and prototyping, Xsens provides the MTi-630 and MTi-670 Development Kits (MTi-630-DK
and MTi-670-DK). In addition to the RS232, CAN and UART pin connectors of the MTi 600-series
module, the Development Kit offers a direct USB, RS232, RS422 and CAN interface. Technical details
of the Development Kit and its usage can be found in the MTi 600-series DK User Manual1.
The MT Low Level Communication Protocol1document provides a complete reference for the
protocols used to communicate with Xsens Motion Trackers on low-level basis. The MT Low Level
Communication Protocol document also describes the synchronization messages and settings in
detail.
Table 1 summarizes all available official documents for the Xsens MTi product line.
Table 1: MTi product documentation overview
MTi 1-series
MTi 600-series
MTi 10/100-series
MTi Family Reference Manual
MTi User Manual
MTi 1-series Datasheet
MTi 600-series Datasheet
MTi 1-series DK User Manual
MTi 600-series DK User Manual
MTi 1-series HW Integration
Manual
MTi 600-series HW Integration Manual
MT CAN protocol Documentation
MT Manager Manual
Magnetic Calibration Manual
MT Low Level Communication Protocol Documentation
Firmware Updater User Manual

www.xsens.com
2
Document MT1601P.A
© Xsens Technologies B.V.
Hardware Integration Manual MTi 600-series
2 Interfaces
2.1 Pin Configuration
Figure 1 shows the pin configuration of the MTi-600.
Figure 1: Pin configuration of the MTi-600
Table 2 shows the pin descriptions.
Table 2: Pin descriptions
Pin
Name
I/O type
Description
1
VIN
PWR
Power input
2
GND
PWR
Ground
3
CAN_H
I/O
CAN bus differential low side
4
CAN_L
I/O
CAN bus differential high side
5
RS232_TxD
O
RS232 transmitter output to host
6
RS232_RTS
O
RS232 Ready To Send output to host
7
RS232_RxD
I
RS232 receiver input from host
8
RS232_CTS
I
RS232 Clear To Send input from host
9
SYNC_IN1
I
Multifunctional synchronization input
10
SYNC_IN2
I
Multifunctional synchronization input
11
GNSS_TxD
O
RS232 transmitter output to GNSS module
12
GNSS_RxD
I
RS232 receiver input from GNSS module
13
SYNC_OUT
O
Configurable synchronization output
14
GND
PWR
Ground
15
UART_TxD
O
UART transmitter output
16
UART_RxD
I
UART receiver input

www.xsens.com
3
Document MT1601P.A
© Xsens Technologies B.V.
Hardware Integration Manual MTi 600-series
2.2 Communication to host
The MTi-600 is designed to be used as a peripheral device in embedded systems or as a standalone
unit. The MTi-600 supports Controller Area Network (CAN), RS232 and Universal Asynchronous
Receiver/Transmitter (UART) protocols for the communication between the MTi-600 and a host. See
Table 3 for interface specifications. For the physical connection recommendations, see section 4.3.
Table 3: Host communication interfaces specifications
Interface
Symbol
Min
Typ
Max
Units
Description
CAN
fCAN
10.0
250.0
1000
kbps
Host CAN Interface Baud Rate
RS232
fRS232
4.8
115.2
1000
kbps
Host RS232 Interface Baud Rate
UART
fUART
4.8
115.2
2000
kbps
Host UART Interface Baud Rate
A USB and RS422 interface is possible through a UART to USB/RS422 converter (see example in the
MTi 600-series Development Kit).
At its core, the module uses the Xsens-proprietary Xbus protocol which is compatible with all Xsens
Motion Tracker products. This protocol is available on all interfaces, UART, RS232 and CAN.
The MT Low Level Communication Protocol Documentation is a complete reference for the protocol
1
.
2.2.1 CAN
The CAN interface of the MTi-600 does not include a termination resistor; it can be used in a CAN bus
that already incorporates the required termination. If used in a single device connection, a 120 Ω
termination resistor needs to be added between the CAN_H and CAN_L pins.
For more information please review the MT CAN Protocol Documentation1.
2.2.2 RS232
The RS232 interface complies with the standard RS232 voltage levels. It includes hardware flow control
through RTS and CTS lines.
The RTS signal is an output of the MTi-600. If the RTS line is low, the module is busy and unable to
receive new data. Otherwise, the module’s UART is idle and ready to receive. The CTS signal is an
input for the MTi-600. The module checks the state of the CTS line at the start of every byte it transmits.
If CTS is high, the module transmits the byte. Otherwise, it postpones transmission until CTS is raised.
If flow control is not used the CTS input should be connected to a logic high to make sure that the MTi-
600 can transmit data. A RS232 logic high voltage should be between +3 V and +25 V.
The CTS signal is an input for the module. The module checks the state of the CTS line at the start of
every byte it transmits. If CTS is high, the module transmits the byte. Otherwise, it postpones
transmission until CTS is raised. When during the transmission of a byte the user lowers the CTS
signal, then the module completes transmission of that byte before postponing further output. The
module will not retransmit this byte. Figure 2 shows the behaviour of the TX and CTS lines.
1
Links to the latest available documentation can be found via the following link: Xsens MTi Documentation

www.xsens.com
4
Document MT1601P.A
© Xsens Technologies B.V.
Hardware Integration Manual MTi 600-series
Figure 2: Data transmit behaviour under CTS
The RTS signal is an output of the module. If the RTS line is low, the module is busy and unable to
receive new data. Otherwise, the module’s UART is idle and ready to receive. After receiving a byte
the direct memory access (DMA) controller of the module will transfer the byte to its receive first-in-
first-out (FIFO) buffer. The module will pull down the RTS signal during this transfer. Therefore, with
every byte received, the module lowers the RTS line shortly. Figure 3 shows this behaviour.
Figure 3: RTS behaviour during data reception
The user can use this communication mode without hardware flow control. In this case, the user must
tie the CTS line high (e.g. VIN) to make the module transmit.
2.2.3 UART
The UART interface can be used to directly connect to an MCU with 3.3 V IO-levels. The user can
configure the MTi 600-series module to communicate over UART. The UART frame configuration is 8
data bits, no parity and 1 stop bit (8N1). The UART protocol only has the TX and RX lines without any
flow control.
2.3 GNSS receiver interface
The MTi-670 variant of the MTi 600-series module family supports external inputs from a GNSS receiver,
such as the uBlox MAX-M8 GNSS receiver. For the GNSS receiver, the RS232 or UART communication
pins of the receiver need to be connected to the GNSS_TxD and GNSS_RxD pins of the MTi-670
module. In case of a UART interface on the GNSS receiver an additional RS232 transceiver should be
connected in-between the MTi-600 and the GNSS receiver. See Figure 4 for connection details and
Table 4 for interface specifications.
The PPS/TIMEPULSE output of the GNSS receiver should be connected to either one of the SYNC
inputs of the MTi-600. The used SYNC input needs to be configured in software accordingly. Under
default configurations, the PPS/TIMEPULSE output should be connected to SYNC_IN1
Table 4: GNSS receiver interface specifications
Interface
Symbol
Typ
Max
Units
Description
RS232
fGNSS
115.2
1000
kbps
GNSS Interface Baud Rate

www.xsens.com
5
Document MT1601P.A
© Xsens Technologies B.V.
Hardware Integration Manual MTi 600-series
Figure 4: Connections for the GNSS interface
2.4 SYNC
The MTi-600 has two multifunctional synchronization inputs and one synchronization output. The
electrical specifications can be seen in Table 7. Refer to the MTi 600-series Datasheet
2
for configuration
details.
2
Links to the latest available documentation can be found via the following link: Xsens MTi Documentation
MTi-670
GNSS receiver
RS232
transceiver
PPS
RS232
UART
RS232
UART
SYNC_IN

www.xsens.com
6
Document MT1601P.A
© Xsens Technologies B.V.
Hardware Integration Manual MTi 600-series
3 Electrical Specifications
This section lists the recommended electrical operating conditions for the MTi-600 series module.
3.1 Supply voltage
The MTi-600 series module has a single supply pin that can be supplied with a voltage within the range
specified in Table 5.
Table 5: Supply voltage specifications
Symbol
Min
Typ
Max
Unit
Description
VIN
4.5
5
24
V
Power input voltage
3.2 Power consumption
The power consumption of an MTi 600-series module depends, among others, on the input voltage,
sample rate and communication protocol. Table 6 shows some typical power consumption values for
different MTi-600 types.
Table 6: Power consumption specifications
Typ
Unit
Conditions
MTi-630
320
mW
5V, UART, measurement mode, 400Hz, 921.6 kbps
MTi-630
350
mW
5V, RS232, measurement mode, 400Hz, 921.6 kbps
MTi-630
495
mW
24V, UART, measurement mode, 400Hz, 921.6 kbps
MTi-630
525
mW
24V, RS232, measurement mode, 400Hz, 921.6 kbps
MTi-670
310
mW
5V, UART, measurement mode, 400Hz, 921.6 kbps
MTi-670
340
mW
5V, RS232, measurement mode, 400Hz, 921.6 kbps
MTi-670
495
mW
24V, UART, measurement mode, 400Hz, 921.6 kbps
MTi-670
530
mW
24V, RS232, measurement mode, 400Hz, 921.6 kbps
3.3 I/O pins
The I/O interface specifications are listed in Table 7.
Table 7: I/O interface specifications
I/O interface
Symbol
Min
Typ
Max
Unit
Description
CAN
VI(DIFF)(R)
-4.0
0.5
V
Recessive differential input voltage
-12V < V(CANH, CANL) < +12V
VI(DIFF)(D)
0.9
9.0
V
Dominant differential input voltage
-12V < V(CANH, CANL) < +12V
VO(DIFF)(R)
-500
0
50
mV
Recessive differential output voltage
VO(DIFF)(D)
1.3
2.0
5.0
V
Dominant differential output voltage
VO(L)(D)
0.5
1.5
2.25
V
CAN_L dominant output voltage

www.xsens.com
7
Document MT1601P.A
© Xsens Technologies B.V.
Hardware Integration Manual MTi 600-series
VO(H)(D)
2.75
3.5
4.5
V
CAN_H dominant output voltage
RS232
(GNSS)
VIL
-25
0.6
V
Low input voltage
VIH
2.4
+25
V
High input voltage
VOT
±5
±5.4
V
Driver Output Voltage swing
UART
VIL
0
0.88
V
Low input voltage
VIH
2.29
3.6
V
High input voltage
VOL
0
0.44
V
Low output voltage
VOH
2.6
3.3
V
High output voltage
SYNC_IN1/
SYNC_IN2
VIL
-25
0.6
V
Low input voltage
VIH
2.4
+25
V
High input voltage
SYNC_OUT
VOL
0
0.44
V
Low output voltage
VOH
2.6
3.3
V
High output voltage

www.xsens.com
8
Document MT1601P.A
© Xsens Technologies B.V.
Hardware Integration Manual MTi 600-series
4 Design
This section describes the (mechanical) design and hardware integration considerations of the MTi
600-series module. 3D models of the module are available and can be downloaded online:
https://base.xsens.com/hc/en-us/articles/360023863393
4.1 Sensor reference frames
The MTi 600-series module uses a right-handed coordinate system as the basis of the sensor frame.
The default sensor coordinate system is printed on the side of the MTi and is shown in Figure 5. More
details regarding (the modification of) the reference frames of the MTi can be found in the MTi 600-
series Datasheet
3
and MTi Family Reference Manual3.
Figure 5: Default sensor coordinate system for the MTi 600-series module
4.2 Origin of accelerometer
The accelerometer determines the origin of measurements. The in Figure 14 shows the location of
the accelerometer of the MTi 600-series module.
Figure 6: Location origin of measurements (dimensions in mm)
3
Links to the latest available documentation can be found via the following link: Xsens MTi Documentation

www.xsens.com
9
Document MT1601P.A
© Xsens Technologies B.V.
Hardware Integration Manual MTi 600-series
4.3 Physical connections
The connector on the MTi-600 series module is a 16 pins, 1.27 mm pitch male connector of Phoenix
Contact (FP 1,27/ 16-MV 1,75 –1714936). This connector supports an SMD counterpart that can be
soldered onto a PCB as well as a ribbon cable (IDC) counterpart. In order to mount the MTi-600 onto a
PCB, the connector should be facing down and the MTi-600 housing should be supported with M2
spacers that can be soldered onto the PCB. When using a ribbon cable the MTi-600 can be mounted
upside-down to create easy access to the connector.
Figure 7 shows both mounting options. In both cases, the MTi-600 is fixated with three M2 screws with
a length of at least 12mm. It is recommend to use screws and spacers with weak magnetic properties
to reduce the influence on the internal magnetometer.
Figure 7: Connection options (left: PCB, right: standalone, dimensions in mm)
4.3.1 Footprint for PCB layout
Figure 8 shows the recommended footprint of the MTi-600 counterpart connector together with the three
spacers. Table 8 shows the recommended parts for this mounting option.
Figure 8: Layout footprint example (dimensions in mm)

www.xsens.com
10
Document MT1601P.A
© Xsens Technologies B.V.
Hardware Integration Manual MTi 600-series
Table 8: Recommended mating/mounting parts
Part
Manufacturer + part number
Description
SMD
connector
Phoenix Contact: 1714892
(FP 1,27/ 16-FV 6,25)
To be used in combination with 5 mm spacers
(shown in Figure 7)
Phoenix Contact: 1715000
(FP 1,27/ 16-FV 9,05)
To be used in combination with 8 mm spacers
PCB
spacers
MAC8: TH-1.6-5.0-M2
M2 x 5 mm, recommended
Würth Elektronik: 9774050243R
M2 x 5 mm, not recommended (ferromagnetic)
Screws
Brass, M2 x 12 mm
4.3.2 Footprint for standalone mounting
Figure 9 shows the mounting hole positions for the MTi-600 when mounted upside-down for the IDC
connection. Table 9 shows the recommended parts for this mounting option.
Figure 9: Standalone mounting hole positions (dimensions in mm)

www.xsens.com
11
Document MT1601P.A
© Xsens Technologies B.V.
Hardware Integration Manual MTi 600-series
Table 9: Recommended mating/mounting parts
Part
Manufacturer + part number
Description
IDC
connector
Phoenix Contact: 1714903
(FP 1,27/ 16-FWL)
Single IDC connector
Phoenix Contact: 1010258/P/xxx
(FP 1,27/ 16-FWL-10/P/xxx)
Cable assembly with one IDC connector;
replace xxx with cable length in m (0.05 –0.95)
Phoenix Contact: 1010251/P/xxx
(FP 1,27/ 16-FWL-11/P/xxx)
Cable assembly with two IDC connectors;
replace xxx with cable length in m (0.05 –0.95)
Screws
Brass, M2 x 12 mm
4.4 Mechanical stress
In general, it is recommended to place the MTi 600-series module in an area on the PCB where
mechanical stress is minimal. The following paragraphs describe possible causes of mechanical stress
and ways to reduce it.
4.4.1 Torque
The connector of the MTi-600 is soldered onto the PCB board which also contains the sensing
elements. Care should be taken to design the mounting such (see chapter 4.3) that there is no stress
on the connector when mounted on the PCB or connected with a ribbon cable. As any stress on the
connector could potentially result in torque on the PCB which can lead to unwanted biases and signal
noise.
4.4.2 Vibrations
The MTi 600-series features an industry-leading signal processing pipeline (AttitudeEngineTM) which
rejects vibrations. For best results however, it is recommended that the MTi 600-series is mechanically
isolated from vibrations as much as possible. Especially in applications where vibrations are likely to
occur, the anchor points of the PCB that holds the MTi 600-series module should be dampened. The
required type of dampening varies from application to application.
4.5 Magnetometer
The MTi 600-series uses a 3D magnetometer for measuring the geomagnetic field. This part is sensitive
to magnetic disturbances. Magnetic disturbances can be calibrated for or identified and rejected by the
MTi, however it is recommended to avoid their influence during hardware integration.
4.5.1 Ferromagnetic materials
Ferromagnetic materials can be magnetized and the magnetic behaviour can change during operation.
This behaviour will influence the measurements of the 3D magnetometer of the MTi 600-series.
Therefore, it is recommended to keep these ferromagnetic materials away from the MTi 600-series.
4.5.2 High currents
High current power lines on the PCB will introduce magnetic fields that may influence the measurements
of the 3D magnetometer of the MTi 600-series. Place high current power lines away from the MTi 600-
series. Example: a power line with a current of 100 mA at a distance of 10 mm from the magnetometer,
will introduce an error of 2 µT.

www.xsens.com
12
Document MT1601P.A
© Xsens Technologies B.V.
Hardware Integration Manual MTi 600-series
More information on magnetic interference can be found in the MTi Family Reference Manual
4
. Static
magnetic disturbances can be calibrated for, see the Magnetic Calibration Manual4.
4
Links to the latest available documentation can be found via the following link: Xsens MTi Documentation

www.xsens.com
13
Document MT1601P.A
© Xsens Technologies B.V.
Hardware Integration Manual MTi 600-series
5 Packaging information
The MTi 600-series packaging boxes contain from 5 up to 20 modules.
Box Dimensions (mm)
Box packaging
information
Length
Width
Height
Qty/Tray
MOQ 5
Qty/Box
MOQ 5
285
185
75
5-20
units
5-20
units
NOTES:
•All dimensions are in millimeters.
•Pictured tray and box representative only, actual tray may look different.
CONTENT:
•5 to 20 modules per box.
•Calibration certificate.
Tray lid
Tray for 20 modules
Standard
issued
Xsens box