Xylem YSI Pro Swap Logger User manual

Quick Start Guide
Item #610174
Thank you for using the ProSwap
Logger for your water monitoring!
This document will assist in the initial
steps required to set up and use the
ProSwap Logger.
The ProSwap Logger is a single port
sonde with built-in temperature and
depth sensors, and it is designed for
use with any single ProDSS digital
smart sensor.
NOTE: Turbidity and Total Algae
sensors must be used with the
Extended Probe Guard [626740]
(sold separately).
Refer to the ProSwap Logger
User Manual for:
• Part numbers and accessories
• Maintenance guidelines
• Sensor calibration instructions
• Connecting ProSwap Logger to
a data logger
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
Item Numbers
610150-XX
610151-XX
610152-XX
610153-XX
610154-XX
610155-XX
1

Preparing for Use
To prepare the sonde for operation, you will need to:
1. Install sensor on the bulkhead or plug the port
2. Connect ProSwap Logger to a handheld or PC via USB Adapter (not included)
Contents
• ProSwap Logger with Integrated Cable
• Probe Guard
• Weight (for Probe Guard)
• Storage Sleeve
• Sponge
• Graduated Cylinder
• USB Drive (contains Kor Software)
• Cable Connector Cap
• Cable Grip Kit
• Cable Management Kit (4m, 10m, 20m) or Cable Spool (30m+)
• Maintenance Kit
• Desiccant Kit (Vented units ONLY)
Unpacking and Inspection
Inspect the outside of the shipping container(s) for damage. If you see any damage, contact the
shipping carrier immediately.
Carefully remove the equipment from the shipping box and verify that all contents are present.
AA
AA
AA
AA
AA
AA
2

AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
Connection to ProDIGITAL Handheld
The ProSwap Logger is designed to interface with the
ProSwap Handheld and ProDSS Handheld meters.
1. Align the keys on the cable connector with the slots
on the handheld connector.
2. Push together firmly, and then twist the outer ring
clockwise until it locks into place.
3. Power on the handheld to calibrate and set up for
logging.
The handheld connection provides power to the
ProSwap Logger. Loggers with internal battery may be
charged via this connection.
Sensor Installation
The ProSwap Logger includes built-in temperature and
depth sensors in addition to a single port. The port will
allow any ProDSS smart sensor to be connected.
1. Remove the port cover shipped with the cable.
2. Apply a thin coat of lubricant to the sensor o-rings.
3. Carefully align the sensor and bulkhead connectors
by inserting the sensor into the port then gently
rotating the sensor until the connectors align. Once
aligned, push the sensor toward the bulkhead until
the sensor seats in the port.
4. Finger-tighten the retaining nut clockwise. If
any resistance is felt, loosen the retaining nut
completely to prevent cross-threading.
5. Use the sensor installation tool to tighten the
retaining nut clockwise until snug. Be careful not to
over-tighten the retaining nut.
6. Install the probe guard.
3

Item# 610174 Dwg# 610174
March 2021 Rev A
1725 Brannum Lane
Yellow Springs, OH 45387
[phone], [phone]
[email protected]
YSI.com
Powering the Logger
The ProSwap Logger comes in two versions: one with an internal, rechargeable lithium ion
battery and one without internal power.
Internal Battery
A fully charged internal battery should last at least 90 days at a 15 minute logging interval.
Battery life will vary depending on which ProDSS Sensor is installed.
The battery may be recharged via connection to a power source including a handheld, USB
adapter, or external power supply. Full recharge time may take up to 14 hours depending on the
power source.
External Power
For the non-battery logger, or to charge the battery version, there are several options to supply
power (these options are all sold separately):
• ProSwap or ProDSS Handheld – The handheld will power the logger as long as it is connected
and powered on.
• ProSwap Logger AA Power Pack – The power pack utilizes six AA batteries to provide power to
the logger for at least 90 days at a 15 minute logging interval.
• USB Adapter – The USB Adapter will power the logger when connected to a PC USB port or
AC adapter.
• Flying Lead Adapter – The flying lead adapter may be used to supply external power and
provide communication with a data logger.
Connection to Kor Software via USB Adapter or Handheld
The ProSwap Logger can be connected to a PC running Kor Software via a USB adapter. A
ProDIGITAL USB adapter is sold separately. Additionally, the software communication may be
established through the handheld’s USB port.
1. Install Kor Software from the included USB Drive or
download the latest version from YSI.com. Follow
the prompts to install the new drivers.
2. Connect the ProSwap Logger to a USB adapter or
handheld.
3. Connect the USB cable to the PC to establish
communication.
4. Check for firmware updates.
The USB connection provides communication and power to the ProSwap Logger. Loggers with
internal battery may be charged via this connection.
AA
AA
AA
AA
AA
AA