Yamaha CL5 Instruction manual

CL5 DISPLAY
CL0
QUICK START MANUAL
6YD-XXXXU-E0

Introduction
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
Device Overview
ÀTouchscreen
ÁAutomatic backlight sensor
ÂPower key
Engine Data Screen
The engine data screen appears when you turn on the device.
This screen varies based on the engine network and throttle
controller.
From this screen, you can access other data screens and the
home screen. To open a different screen, swipe the screen right
or left, or select the arrows on either side of the screen.
ÀData fields
Hold to replace the data.
ÁCurrent time
Hold to view trip data.
ÂPress to set the joystick button Set Point functions (Helm Master®).
ÃTank level information
Hold a tank to view detailed tank level sensor information.
ÄGPS signal strength
Select to set the Fish Point high RPM limit (Helm Master).
Select to set the trolling speed (Command Link Plus®).
ÅData fields
Hold to replace the data.
ÆShift position
ÇTachometer and trim angle
Hold to change the background.
ÈEngine information
Hold to replace the data and change the gauge appearance.
Engine Alert Icons
Red icons indicate engine abnormalities.
NOTICE
Consult your Yamaha® dealer if the problem cannot be located
and corrected.
Low cooling water pressure.
Low oil pressure.
Stop the engine. Check the engine oil level, and add more oil if
necessary.
NOTICE
Do not continue to run the engine if this indicator is on. Serious
engine damage will occur.
Engine overheating.
Stop the engine immediately. Check the cooling water inlet, and
clear it if it is blocked.
NOTICE
Do not continue to run the engine if this indicator is on. Serious
engine damage will occur.
Low battery voltage.
Check the battery and battery connections, and tighten all loose
battery connections.
Return to port soon if tightening the battery connections does not
increase the battery voltage. Consult your Yamaha dealer
immediately.
NOTE: Do NOT stop the engine when this alert is on. If you do,
you may not be able to restart the engine.
Water in the fuel.
Water has collected in the fuel filter (fuel separator).
Stop the engine immediately and consult the engine manual to
drain the water from the fuel filter.
NOTE: Gasoline mixed with water might cause damage to the
engine.
Check engine/maintenance alert.
Consult your Yamaha dealer immediately. The check engine alert
also appears when more than 100 hours have elapsed since the
previous maintenance.
Engine alert notification. (Helm Master)
Engine emission issue.
Engine Condition Icons
Orange icons indicate engine conditions.
Yamaha security system is on.
Engines are under synchronization control.
Engines are warming up.
GPS Signal Strength Icons
The icons shown in the upper-right of the engine screen indicate
the GPS signal strength.
GPS satellite signal strength
No GPS satellite signal
2 Quick Start Manual

Pairing the Remote Control to the CL0 Device
You must pair the remote control to the CL0 device before
you can use the CL0 device.
1 Turn on the CL0 device.
The device turns on in paring mode. If it is not in paring
mode, hold the CL0 power button for 3 seconds.
2 On the remote control, hold the MENU and keys.
The device beeps until the remote control and device are
paired.
CL0 Remote Control
Quick Start Manual 3
ÀTurn to highlight.
Push to select
ÁReturns to previous the screen or menu.
ÂOpens the menu for that page.
ÃHold to assign a shortcut key to the current page.
Press to open the assigned page..
ÄPress to adjust the backlight brightness
BACK MENU
1 2
Yamaha Autopilot
WARNING
You are responsible for the safe and prudent operation of your
vessel. The autopilot is a tool that enhances your capability to
operate your boat. It does not relieve you of the responsibility of
safely operating your boat. Avoid navigational hazards and
never leave the helm unattended.
Always be prepared to promptly regain manual control of your
boat.
Learn to operate the autopilot on calm and hazard-free open
water.
Use caution when operating the autopilot near hazards in the
water, such as docks, pilings, and other boats.
The autopilot system continuously adjusts the steering of your
boat to maintain a constant heading (heading hold).
When the chartplotter is connected to a compatible Yamaha
autopilot system, you can view the autopilot information using
the Yamaha autopilot screen and overlay bar (Yamaha
Autopilot, page 2). For information about compatible Yamaha
autopilot systems, contact your Yamaha dealer.
When the chartplotter is connected to a compatible Garmin®
autopilot system, you can engage and control the autopilot from
the chartplotter (Autopilot, page 38). For information about
compatible Garmin autopilot systems, go to garmin.com.
Actual heading
Intended heading (heading the autopilot is steering toward)
Yamaha Autopilot Settings
From a Yamaha engine screen, select Menu > Autopilot
Setting.
Pattern Set: Allows you to select an autopilot pattern.
Direction: Sets a port or starboard direction for the pattern.
Spacing: Sets the spacing for the pattern.
Length: Sets the length of the pattern.
Amplitude: Sets the angle for the zigzag pattern.
Initial Radius: Sets the radius of the spiral pattern.
Final Track Point Mode: Sets the mode for the autopilot when it
reaches the end of a route.
Offset Distance: Sets an offset distance to navigate parallel to
a route.
Yamaha Autopilot Screen
Yamaha Autopilot Overlay Bar
Autopilot mode
Actual heading
Intended heading (heading the autopilot is steering toward)
Opens the full autopilot screen and menu
WARNING
Only replace batteries with AAA batteries. Using other batteries
presents a risk of fire or explosion.
Contact your local waste disposal department to dispose of the
device/batteries in accordance with applicable local laws and
regulations

4 Quick Start Manual

© 2017–2019 YAMAHA Motor Co., LTD or its subsidiaries
Yamaha®, the Yamaha logo, Command Link Plus®, and Helm Master® are trademarks of the YAMAHA Motor Co., LTD.
Garmin®, the Garmin logo, and BlueChart® are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and
other countries. Garmin LakeVü™ and SmartMode™ are trademarks of Garmin Ltd. or its subsidiaries. These
trademarks may not be used without the express permission of Garmin.
microSD® and the microSD logo are trademarks of SD-3C, LLC.
All other trademarks and copyrights are the property of their respective owners.
December 2019
190-0XXXX-01_0B
6YD-XXXXU-E0