YEEUU S1 Smart Lock User manual

S1 Smart Lock
Quick Start Guide
Please follow us on YouTube channel: YEEUU
or visit our website: YEEUU.com
or email to [email protected]
to get more info of operation manual.
Lock Show
1
1
3
2
2
45
6
3
4
Front Lever Back Lever
Fingerprint Identification Area
Key Open Area
Password Area
5
Battery Compartment Area
6
Anti Lock Knob
Door Card Identification Area
Basic Parameters
Door Opening Method: fingerprint, card, password, APP, mechanical key
Storage Capacity: 100PCS of door cards + fingerprints + passwords
Working Voltage: 3 No.7 AAA alkaline dry batteries
Battery Life: Up to 1 year (unlock 10 times a day)
Working Temperature: -20°C ~ 70°C
Working Humidity: 40%RH ~ 80%RH
Fitting category A: single latch
Door Thickness: 30mm-80mm
Door Prep: 54mm diameter face hole &25mm diameter latch hole
Daily Maintenance
· Installation environment: requires at least a canopy, do not keep the lock
completely exposed in open air.
· Please do not scratch the fingerprint identification area with a sharp
object.
· Please exchange both three batteries at the same time, do not use
mixed new batteries with old ones.
· The mechanical key is a measure for emergency door opening, please
keep at least 1 mechanical key in a safe place other than home(e.g. office,
parents’ house).
· Please adjust the door or door frame in time if it deforms, otherwise the
latch will not enter the door frame hole position smoothly.
Instructions
Note: Please install 3 x No.7 AAA alkaline dry batteries before use.
Download APP:
Log in AppStore/GooglePlay to search “YEEUU” and download the APP.
Add device:
Register and log in “YEEUU” account; click “Add Device” or click symbol
“+” at the upper right corner on “Home page”; select “Auto Scan” to start
searching; after the device is searched, click “next” to connect the lock to
be added.
Add/use fingerprint to open the door(Applicable fingerprint version):
Log in “YEEUU” APP; select the device and enter “Settings” page; click
“Fingerprint Management” to enter the page; click “Add Fingerprint” at
the upper right corner and put the finger on the fingerprint identification
area for admission.
Add/use door card to open the door:
Log in “YEEUU” APP; select the device and enter “Settings” page; click
“Door Card Management” to enter the page; click “Add Door Card” at the
upper right corner and then put the door card on the card identification
area for admission.
Add Password:
Log in “YEEUU” APP; Select the device and enter the “Settings” page;
click “Password Management” to enter the page; click “Add Password” to
set the password; Please note that the initial device password is
“123456”.
Use APP to open the door:
Log in “YEEUU” APP; select the page for the device to be entered, click
the icon at the page center after your APP is connected with the lock; turn
the handle to open the door when the green light flashes.
View records:
Log in “YEEUU” APP; select the page for the device to be entered; after
your APP is connected with the lock, click
“Opening Record/Alarm” to enter the page to view opening/alarm re-
cords.
Unbind the door lock：
Unbind the door lock: [Remove Device] button shows up when a non-ad-
ministrator user performs the above mentioned operations, click it and
follow the prompt to unbind.
Low Voltage Alarm:
Yellow light flashes 2 times.
Operation Failed:
Red light flashes 2 times, buzzing 2 times.
Error Lock:
Red light flashes 5 times.
Frequently Asked Question
Opening door by mobile phone fails.
Check whether the batteries are loaded and working properly; Check the
networking status of mobile phone and perform operation again; Remove
the batteries and re-load.
Opening door by card fails.
Check whether the batteries are loaded and working properly; Confirm
whether the card has been added; Remove the batteries and re-load.
Opening door by fingerprint fails.
Check whether the batteries are loaded and working properly; Confirm
whether the fingerprint has been added; Remove the batteries and
re-load; Ensure that the finger is dry.
Yellow light flashes when opening the door.
Low power, please replace 3 No.7 AAA alkaline dry batteries in time.
Red light flashes 5 times when opening the door.
Error in lock, please try to unlock the door by fingerprint/door card/pass-
word 1 minute later, or use the APP to unlock it.
No response when opening the door.
Please check if the batteries are loose; If the batteries are dead, please
replace the batteries.
Login/registration cannot be performed normally.
Please check whether the network is running properly.

YEEUU S1 Smart Lock
Hangzhou Ujia Technology Co., Ltd.
Made in China
Download APP
1. Open Google play or App Store.
2. Download and install “YEEUU” App.
Product Accessories Diagram
Installation Intro
Front Lever Back Lever Rear decorative
Cover
Square bar 80mm
Square bar 100mm
Square Bar
Spring
Bafflex2
Keyx3
Door Cardx3
Lock Pinch Plate
(Including
Striking Case)
Handle Latch Front Lock
Core Cover
Back Lock
Core Cover
Auxiliary Ring
Connecting
Rod Boltx3
Bamboo
Screwx3 M4*80
ScrewdriverFront Cover Back Cover
Lever Screwx4
M4*8
Battery*3
Self-Tapping
Screwx5 M4*20
Installation Steps
Confirm the door thickness and door hole size meet the following pa-
rameters.
2.Install the lock body
1. Door hole prep
3.Install the front panel
Assemble the front cover: fix the bolt on the front cover and tighten with
the handle screw M4 * 8.
60-146mm55-87mm
4.Install the front handle
1) Align the screw of the front handle with the round hole on the lock body
and install it on the door.
(Be aware that the fingerprint side is facing upwards, choose whether to use the front baffle according
to the size of the door hole)
2) Install the back baffle
(Cut the bamboo screws according to the door thickness , be aware that the length of the screw should
be less than 10mm of the door. according to the size of the door hole, choose whether to use the back
baffle according to the size of the door , the bolt should be face outward)
3) Install the square pole and test
Select the square pole inserted into the square hole of the front handle,
put on the auxiliary ring, and check whether the square pole rotates flexi-
bly.
5.Back handle installation
1）Install the square rod spring into the center hole of the back handle.
2) Remove the lock knob cover of the back handle and fix the back handle
to the door with screws.
Assemble the Spring into the
center hole of the Inside Lever
first
6. Install the battery
1) Remove the battery cover, install three AAA batteries, tighten the screws
after installing the battery cover.
2) Install the cover.
3) Select the lock knob cover or back decoration cover for installation ac-
cording to the requirements.
7.Test
Remove the cover, insert the key and turn 90 degrees, then try the front
and back handle in turn, and check the movement of the lock tongue. If the
operation is not smooth, please check again all installation steps.
8. Install the front and back decorative cover
PS: Based on your needs.
1) Assembling the front decorative cover
2) Cut the bamboo screws according to the door thickness , be aware that
the length of the screw should be less than 10mm of the door.
3) Assembling the back decorative cover
Congratulations, you have successfully installed the Yeeuu Smart Lock!