Yellobrik OTT 1442 User manual

Technical Specications OTT 1442
Dual Channel 12Gbit SDI to Fiber Transmitter (CWDM)
IN
2
+12V d.c.
Power
0V
TX1TX2
LYNXTechnik AG
12G
CWDM
Dual Fiber Optic/
SDI Transmitter
IN
1
WARNING
CLASS 1
Laser Product
WARNINGWARNING
LASER RADIATION
Do not view directly with
optical instruments
CLASS 1M LASER PRODUCT
SDI Video
Loop Output
SDI Video
Input
DC Power
Input
LC/PC Fiber
Output
Power
Connected
Transmitting
Data
SDI Input 2 x SDI video input
75 Ohm BNC connectors
SMPTE 2082-1, SMPTE 2081-1, SMPTE 424M, SMPTE 292M, SMPTE
259M, DVB-ASI
Multi-standard operation from 270Mbit/s to 12Gbit/s
Multirate reclocking:
270Mbit/s - 1.5Gbit/s - 3Gbit/s - 6Gbit/s - 12Gbit/s
Automatic cable EQ:
245m @ 1.5Gbit/s, 145m @ 3Gbit/s (Belden 1694A cable)
85m @ 12Gbit/s, 6Gbit/s (Belden 4794R cable)
Optical Output 2 x fiber optic output
SMF (singlemode) using LC/PC connection
SMPTE 297M - 2006
Wavelength selectable (SFP not included in module)
Optical power: see selected optical SFP
TX active LED on side of module
Max. distance: see selected optical SFP
Power +12VDC @ 1.9W nominal (power supply included, without SFP)
(supports 7 - 24VDC input range)
Power LED on side of module
We are constantly adding more yellobrik modules.
Please visit our website for the latest product updates.
www.lynx-technik.com
yellobrik
®
Quick
Reference
yellobrik
®
LYNX
Technik
AG |
www.lynx-technik.com

Connections
The SDI video input is connected to the 75 Ohm BNC connections (up
to12Gbit). The ber connection is LC/PC Simplex SMF (singlemode).
An example of the LC connector shown below (ber optic cable and LC
connectors are not supplied)
Note: The modules are CWDM devices and can
only be used with SMF (Singlemode fiber).
Multimode fiber is not supported.
The ber connection comes standard with an installed rubber plug to
prevent dust contamination. Please keep the plug for later use if the
cable is ever disconnected from the cable.
The basic module has no ber SFP included, The module is typically
used for CWDM applications and the wavelength can be selected from
the available CWDM SFPs.
Operation
The module has two identical (and fully independent) channels.
Operation is full automatic. The SDI input video rates are atuomatically
detected, reclocked, and transmitted over the optical connections.
The OTT 1442 supports any SDI video signal from 270Mbit/s to 12Gbit/s.
Note: If TX LED is OFF, then this indicates that there is no SDI present or
not a valid input.
The module supports hot swapping and hot plugging of connections.
No user settings are provided for this module.
Power
The module requires a 12V DC power input and an LED is provided
to conrms power is connected. A power supply is provided, but
if applying your own power, please provide a clean 12V DC power
source between 7 and 24VDC. The module power consumption is
approximately 1.9W nominal.
Power Lead Strain Relief
The module has a small hole in the case which is located above the
power connection. This prevents the power lead being accidentally
pulled out. Use the supplied tie-wrap and secure the lead as shown
below.
Optional Mounting Solutions
The optional RFR 1001 mounting bracket can be used to permanently
mount the module on any surface or on 19” rack rails.
The optional RFR 1000-1 rack mount can be used to permanently
mount up to 14 yellobrik modules. In addition, the RFR 1000-1 can
provide full power redundancy for all mounted yellobriks.
Note: OTT 1442 is identical in terms of mounting and securing.