Yellobrik OTX 1742-2 User manual

OTX 1742-2
Sync / Analog Video Fiber Transmitter
Analog (SD)Video
or Sync Input
SDTV Mode
(Video/Sync)
DC Power Input
LoopOutput
(terminate if not used)
WARNING
CLASS 1M LASER PRODUCT
We are constantly adding additional yellobrik modules.
Please visit our website for the latest product updates.
www.lynx-technik.com
LASER RADIATION
Do not view directly with
optical instruments
Fiber Output - CWDM
(18Wavelength Selections)
HDTV Mode
(Sync)
Fiber
TX Active
Status LED
Factory Reset
(through hole)
USB Port
(F/W updates + control)
Technical Specifications
Analog Input Sync = analog black burst / SDTV bi-level / HDTV tri-level
Video = NTSC / PAL Composite video
1 x passive loop output (terminate if not used)
75 Ohm BNC connectors
NTSC SMPTE 170M, PAL CCIR624
Analog tri-level sync SMPTE ST 274, ST 276
Multi-standard operation, auto-detect
Return loss: 31dB to 10MHz
Fiber Out
Singlemode
1 x fiber optic singlemode output (CWDM)
LC connection
SMPTE 297M - 2006
18 Wavelength selections per ITU-T G.694.2
1270,1290,1310,1330,1350,1370,1390,1410,1430,1450,1470,
1490,1510,1530,1550,1570,1570,1590,1610nm
Fiber TX active LED on side of module
Max. distances:
OH-TX-4-xxxx SFP option = 40km (24.8 miles - approx)
OH-TX-8-xxxx SFP option = 80km (49.6 miles - approx)
Power +12VDC power supply (included)
Power LED on side of module
Power consumption: 5W
yellobrik
®yellobrik Quick
Reference
®
LYNXTechnik AG Broadcast Television Equipment
®

Power Lead Strain Relief
The module has a small hole in the case located above the power
connection to prevent the power lead being accidentally pulled out.
Use the supplied tie-wrap and secure the lead as shown below.
Connections
The analog video / sync input is made on a standard BNC connector.
A loop out connection is provided. Please terminate the loop output
with a 75 Ohm terminator if not used.
The module is CWDM compatible with selectable SFP sub modules
providing all the standard 18 wavelength choices between 1270nm
standard (40km) and long haul (80km) versions:
OH-TX-4-XXXX = (standard) 40km SFP where XXXX= wavelength
OH-TX-8-XXXX = (long haul) 80km SFP where XXXX = wavelength
this is to prevent dust contamination. Please retain the plug and use if
the cable is ever disconnected from the module.
function correctly if used with Multimode cable.
Operation
Operation of the OTX 1742-2 is fully automatic. The analog video or sync
input format is automatically detected, converted and transmitted over
module to indicate the module operating mode (SDTV or HDTV)
Status LED
The status LED on the top of the module is multifunction:
= Power OK and no internal programmed settings are present
= Power OK and some internal programmed settings are active*
= (out) Power not present
* Some additional internal settings have been made using the yelloGUI. The LED
indicates this by turning yellow. The module can be reset to factory defaults by
using the reset switch (recessed under a hole on the side of the module). When
reset the LED will change back to Green.
USB Port / Firmware Updates / yelloGUI
control of the module using the yelloGUI software application. For
more information and to download the yelloGUI application please
goto: http://yellogui.lynx-technik.com
Firmware updates are always provided free of charge and can be
downloaded from our website. A PC and a USB cable is required for
Optional Mounting Bracket
The optional RFR 1001 mounting bracket can be
used to permanently mount the module on any
Note: OTX 1742-2 is identical in terms of mounting and securing