YOKOGAWA UM33A User manual

IM 05P03D21-11EN page 1/8
Contents
1. Safety Precautions
2. ModelandSufxCodes
3. How to Install
4. HardwareSpecications
5. HowtoConnectWires
6. TerminalWiringDiagrams
Introduction
ThankyouforpurchasingtheUM33ADigitalIndicatorwithAlarms.
ThisoperationguidedescribesthebasicoperationsoftheUM33A.Theguideshould
beprovidedtotheenduserofthisproduct.
Besuretoreadthisoperationguidebeforeusingtheproductinordertoensure
correct operation.
Fordetailsofeachfunction,refertotheelectronicmanual.Beforeusingtheproduct,
refertothetableofModelandSufxCodestomakesurethatthedeliveredproduct
isconsistentwiththemodelandsufxcodesyouordered.Alsomakesurethatthe
followingitemsareincludedinthepackage.
•DigitalIndicatorwithAlarms(themodelyouordered) ............................x1
• Set of Brackets........................................................................................x1
•UnitLabel(L4502VZ) ..............................................................................x1
•TagLabel(L4502VE)(Onlywhenordered.) ...........................................x1
•OperationGuide(thisdocument) ............................................................x4(A3size)
(InstallationandWiring,InitialSettings,Operations,andParameters)
l
TargetReaders
Thisguideisintendedforthefollowingpersonnel;
• Engineersresponsibleforinstallation,wiring,andmaintenanceoftheequipment.
• Personnelresponsiblefornormaldailyoperationoftheequipment.
1. Safety Precautions
Thefollowingsymbolisusedontheinstrument.Itindicatesthepossibilityofinjury
totheuserordamagetotheinstrument,andsignies that the usermust refer to
theuser’smanualforspecialinstructions.Thesamesymbolisusedintheuser’s
manualonpagesthattheuserneedstoreferto,togetherwiththeterm“WARNING”
or“CAUTION.”
WARNING
Calls attention to actions or conditions that could cause serious
or fatal injury to the user, and indicates precautions that should be
taken to prevent such occurrences.
CAUTION
Calls attention to actions or conditions that could cause injury to
the user or damage to the instrument or property and indicates pre-
cautions that should be taken to prevent such occurrences.
AC
AC/DC
Theequipmentwhollyprotectedbydoubleinsulationorreinforcedinsulation.
Functionalgroundingterminals
  (Donotusethisterminalasaprotectivegroundingterminal).
Note
Identiesimportantinformationrequiredtooperatetheinstrument.
nWarning and Disclaimer
(1) YOKOGAWA makesno warrantiesregardingthe productexceptthose statedin
theWARRANTYthatisprovidedseparately.
(2) Theproductisprovidedonan"asis"basis.YOKOGAWAassumesnoliabilityto
anypersonorentityforanylossordamage,directorindirect,arising from the
useoftheproductorfromanyunpredictabledefectoftheproduct.
nSafety,Protection,andModicationoftheProduct
(1)Inordertoprotectthesystemcontrolledby this product andthe product itself,
andtoensuresafeoperation,observethesafetyprecautionsdescribedinthe
user’smanual.Useoftheinstrument in a mannernotprescribedhereinmay
compromise the product's functions and the protection features inherent in the
device.Weassumenoliabilityforsafety,orresponsibilityfortheproduct'squality,
performanceorfunctionalityshouldusersfailtoobservetheseinstructionswhen
operatingtheproduct.
(2)Installationofprotectionand/or safety circuits withrespect to a lightning
protector;protectiveequipmentforthesystemcontrolledbytheproductandthe
productitself;foolprooforfailsafedesignofa process or lineusingthesystem
controlledbytheproductortheproductitself;and/orthedesignandinstallation
ofotherprotectiveandsafetycircuitsaretobeappropriatelyimplementedasthe
customer deems necessary.
(3) Be sureto usethe spareparts approved byYOKOGAWA when replacingparts
orconsumables.
(4) This productis notdesigned or manufacturedto beused in criticalapplications
thatdirectlyaffectorthreatenhumanlives.Suchapplicationsincludenuclear
powerequipment,devicesusingradioactivity, railway facilities, aviation
equipment,airnavigationfacilities,aviation facilities,andmedicalequipment.
Ifsoused,itistheuser’sresponsibility toincludeinthesystemadditional
equipmentanddevicesthatensurepersonnelsafety.
(5) Modicationoftheproductisstrictlyprohibited.
(6) This product is intended to behandled byskilled/trained personnel for electric
devices.
WARNING
l
Power Supply
Ensure that the instrument’s supply voltage matches the voltage
of the power supply before turning ON the power.
lDo Not Use in an Explosive Atmosphere
Do not operate the instrument in locations with combustible
or explosive gases or steam. Operation in such environments
constitutes an extreme safety hazard. Use of the instrument in
environments with high concentrations of corrosive gas (H2S,
SOX, etc.) for extended periods of time may cause a failure.
lDo Not Remove Internal Unit
The internal unit should not be removed by anyone other than
YOKOGAWA's service personnel. There are dangerous high
voltage parts inside. Additionally, do not replace the fuse by
yourself.
lDamage to the Protective Construction
Operation of the instrument in a manner not specified in the
user’s manual may damage its protective construction.
CAUTION
This instrument is an EMC class A product. In a domestic environ-
ment this product may cause radio interference in which case the
user needs to take adequate measures.
2. ModelandSufxCodes
nUM33A [Style:S1]
Model Sufxcode
Optional
sufx
code
Description
UM33A
DigitalIndicatorwithAlarms
(providedwithretransmissionoutputor15VDCloop
powersupply,2DIs,and3DOs)
(Powersupply:100-240VAC)
Type 1:
Basic -0 Standard type
Type 2:
Functions
0None
11additionalDO(c-contactrelay),RS-485communication
(Max.38.4kbps,
2-wire/4-wire)
21additionalDO(c-contactrelay)
36additionalDOs(c-contactrelay:1point,opencollector:
5points)
Type3:Open
networks 0None
Displaylanguage(*1)
-1 English
-2 German
-3 French
-4 Spanish
Casecolor 0White(Lightgray)
1Black(Lightcharcoalgray)
Optionalsufxcodes
/LP 24VDClooppowersupply(*2)
/DC Powersupply24VAC/DC
/CT Coating(*3)
*1: English,German,French,andSpanishcanbedisplayedastheguidedisplay.
*2: The/LPoptioncanbespecifiedonlywhenthecodeforType2is"0","1"or"2."
 Additionally,theRS-485communicationfor"1"oftheType2codeis2-wiresystem.
*3: Whenthe/CToptionisspecified,theUM33Adoesnotconformtothesafetystandards(UL
andCSA)andCEmarking.
nAccessories (sold separately)
Thefollowingisanaccessorysoldseparately.
• LL50AParameterSettingSoftware
Model Sufxcode Description
LL50A -00 ParameterSettingSoftware
• TerminalCover
 ForUM33A:ModelUTAP002
• User’sManual(A4size)
 Note:User’sManualcanbedownloadedfromawebsite.
•User’sManual(CD-ROM),Model:UTAP003
 Note:Containsallmanuals.
3. How to Install
nInstallation Location
Theinstrumentshouldbeinstalledinindoorlocationsmeetingthefollowing
conditions:
• Instrumented panel
 Thisinstrumentisdesignedtobemountedinaninstrumentedpanel. Mount the
instrumentinalocationwhereitsterminalswillnotinadvertentlybetouched.
• Well ventilated locations
 Mounttheinstrumentinwellventilatedlocationstopreventtheinstrument’sinter-
naltemperaturefromrising.
 However,makesurethattheterminalportionsarenotexposedtowind.Exposure
to wind may cause the temperature sensor accuracy to deteriorate. To mount mul-
tipleindicators,seetheexternaldimensions/panelcutoutdimensionswhichfollow.
Ifmountingotherinstrumentsadjacenttotheinstrument,complywiththesepanelcut-
outdimensionstoprovidesufcientclearancebetweentheinstruments.
• Locations with little mechanical vibration
 Installtheinstrumentinalocationsubjecttolittlemechanicalvibration.
• Horizontal location
 Mounttheinstrumenthorizontallyandensurethatitislevel,withnoinclinationto
therightorleft.
Front panel
of the indicator
30°
Keep this angle
within 30°
Note
If theinstrument ismovedfroma location withlowtemperatureandlowhumidity
toaplacewithhightemperatureandhighhumidity,orifthetemperaturechanges
rapidly,condensationwill result. Moreover, in the case of thermocoupleinputs,
measurementerrorswillresult.Toavoidsuchasituation,leavetheinstrumentinthe
newenvironmentunderambientconditionsformorethan1hourpriortousingit.
Donotmounttheinstrumentinthefollowinglocations:
• Outdoors
• Locations subject to direct sunlight or close to a heater
 Installtheinstrumentinalocationwithstabletemperaturesthatremainclosetoan
averagetemperatureof23°C.Donotmountitinlocationssubjecttodirectsunlight
orclosetoaheater.Doingsoadverselyaffectstheinstrument.
• Locations with substantial amounts of oily fumes, steam, moisture, dust, or
corrosive gases
 Thepresence ofoilyfumes,steam,moisture,dust,orcorrosive gasesadversely
affectstheinstrument.Donotmounttheinstrumentinlocationssubjecttoanyof
thesesubstances.
• Areasnearelectromagneticeldgeneratingsources
 Donotplacemagnetsortoolsthatgeneratemagnetismneartheinstrument.Ifthe
instrumentisusedinlocationsclosetoastrongelectromagneticeld generating
source,themagneticeldmaycausemeasurementerrors.
• Locationswherethedisplayisdifculttosee
 TheinstrumentusesanLCDforthedisplayunit,andthiscanbedifculttosee
fromextremelyobliqueangles.Mounttheinstrumentinalocationwhereitcanbe
seenasmuchaspossiblefromthefront.
• Areasclosetoammablearticles
 Absolutelydonotplacetheinstrumentdirectlyonam-
mablesurfaces.Ifsuchacircumstanceisunavoidable
andtheinstrumentmustbeplacedclosetoaammable
item,provideashieldforitmadeof1.43mmthickplated
steel or 1.6 mm thick unplated steel with a space of at
least150mmbetweenitandtheinstrumentonthetop,
bottom,andsides.
• Areas subject to being splashed with water
WARNING
Be sure to turn OFF the power supply to the indicator before install-
ing it on the panel to avoid an electric shock.
150 mm150 mm
150 mm
150 mm
150 mm150 mm
150 mm
150 mm
nMounting the Instrument Main Unit
Provideaninstrumentedpanelsteelsheetof1to10mmthickness.
Afteropeningthemountingholeonthepanel,followtheproceduresbelowtoinstall
the indicator:
1) Insertthe indicator into the opening from the front of the panel so that the
terminalboardontherearisatthefarside.
2) Setthebracketsin placeontheright andleftof theindicator asshowninthe
gurebelow,thentightenthescrewsofthebrackets.Takecarenottoovertighten
them.
Direction to insert the
indicator
Insert the indicator
into the opening at
the front of the panel.
Panel
Bracket
(side mounting hardware)
Bracket
(side mounting hardware)
Terminal board
Insert a screwdriver into the
brackets to tighten the screws.
Appropriate
tightening torque:
0.25 N•m
CAUTION
• Tighten the screws with appropriate tightening torque within 0.25
N•m. Otherwise it may cause the case deformation or the bracket
damage.
• Make sure that foreign materials do not enter the inside of the
instrument through the case’s slit holes.
nExternal Dimensions and Panel Cutout Dimensions
UM33A Unit: mm (approx. inch)
Normal tolerance:
±(value of JIS B 0401-1998 tolerance class IT18)/2
96 (3.78)
48 (1.89)
Bracket
20 (0.79)
65 (2.56)
11
(0.43)
Terminal cover
Bracket
94.6 (3.72)
91.6 (3.61)
105.2 (4.14)
1 to 10
(0.04 to 0.39)
(panel thickness)
(25) (0.98)
(53)
(2.09)
• General mounting
145 (5.71)min.
+0.03
0
(3.62 )
+0.6
0
45
+0.02
0
(1.77 ) +0.8
0
92
70 (2.76) min.
Operation
Guide
IM 05P03D21-11EN
UM33A
Digital Indicator with Alarms
Operation Guide
This operation guide describes installation, wiring, and other tasks required to make the
indicator ready for operation.
1st Edition : Aug. 2010
Installation and Wiring
nWaste Electrical and Electronic Equipment (WEEE),
Directive 2002/96/EC
Thisisanexplanationofhowto dispose ofthisproductbasedonWasteElectrical
andElectronicEquipment(WEEE),Directive2002/96/EC.Thisdirectiveisonlyvalid
intheEU.
Marking
ThisproductcomplieswiththeWEEEDirective(2002/96/EC)
markingrequirement.
Thismarkingindicatesthatyoumustnotdiscard this electrical/
electronic product in domestic household waste.
Product Category
WithreferencetotheequipmenttypesintheWEEEdirectiveAnnex1,this
productisclassifiedasa“MonitoringandControlinstrumentation”product.
Donotdisposein domestichouseholdwaste. Whendisposingproductsinthe EU,
contactyourlocalYokogawaEuropeB.V.ofce.
www.yokogawa.com/ns
YOKOGAWA ELECTRIC CORPORATION
Network Solutions Business Division
2-9-32, Naka-cho Musashino-shi, Tokyo 180-8750 JAPAN
YOKOGAWA CORPORATION OF AMERICA
Head office and for product sales
2 Dart Road, Newnan, Georgia 30265, USA
YOKOGAWA EUROPE B.V.
Headquarters
Euroweg 2, 3825 HD Amersfoort, THE NETHERLANDS
All Rights Reserved, Copyright © 2010 Yokogawa Electric Corporation

IM 05P03D21-11EN page 2/8
4. HardwareSpecications
WARNING
This instrument is for Measurement Category I (CAT.I). Do not use it
for measurements in locations falling under Measurement Catego-
ries II, III, and IV.
Internal Wiring
Outlet
Entrance IV
Cable
III T
I
II
Category Measurement
category Description Remarks
ICAT.I For measurements performed on circuits not
directlyconnectedtoMAINS. -
II CAT.II For measurements performed on circuits di-
rectlyconnectedtothelow-voltageinstallation.
Appliances,portableequip-
ment, etc.
III CAT.III Formeasurementsperformedinthebuilding
installation.
Distributionboard,circuit
breaker,etc.
IV CAT.IV For measurements performed at the source of
thelow-voltageinstallation.
Overheadwire,cable
systems, etc.
nInputSpecications
●UniversalInput(Equippedasstandard)
• Numberofinputs:1
• Inputtype,instrumentrange,andmeasurementaccuracy:Seethetablebelow,
Input Type Instrument Range Accuracy
ºC ºF
Thermo-
couple
K
-270.0to1370.0ºC -450.0to2500.0ºF ±0.1%ofinstrumentrange±1digitfor
0°Cormore
±0.2%ofinstrumentrange±1digitfor
lessthan0°C
±2%ofinstrumentrange±1digitfor
lessthan-200.0°CofthermocoupleK
±1%ofinstrumentrange±1digitfor
lessthan-200.0°CofthermocoupleT
-270.0to1000.0ºC -450.0to2300.0ºF
-200.0to500.0ºC -200.0to1000.0ºF
J-200.0to1200.0ºC -300.0to2300.0ºF
T
-270.0to400.0ºC -450.0to750.0ºF
0.0to400.0ºC -200.0to750.0ºF
B0.0to1800.0ºC 32to3300ºF
±0.15%ofinstrumentrange±1digit
for400°Cormore
±5%ofinstrumentrange±1digitfor
lessthan400°C
S0.0to1700.0ºC 32to3100ºF ±0.15%ofinstrumentrange±1digit
R 0.0to1700.0ºC 32to3100ºF
N -200.0to1300.0ºC -300.0to2400.0ºF
±0.1%ofinstrumentrange±1digit
±0.25%ofinstrumentrange±1digit
forlessthan0°C
E -270.0to1000.0ºC -450.0to1800.0ºF ±0.1%ofinstrumentrange±1digitfor
0°Cormore
±0.2%ofinstrumentrange±1digitfor
lessthan0°C
±1.5%ofinstrumentrange±1digitfor
lessthan-200.0°CofthermocoupleE.
L -200.0to900.0ºC -300.0to1600.0ºF
U
-200.0to400.0ºC -300.0to750.0ºF
0.0to400.0ºC -200.0to1000.0ºF
W 0.0to2300.0ºC 32to4200ºF ±0.2%ofinstrumentrange±1digit
(Note2)
Platinel 2 0.0to1390.0ºC 32.0to2500.0ºF ±0.1%ofinstrumentrange±1digit
PR20-40 0.0to1900.0ºC 32to3400ºF
±0.5%ofinstrumentrange±1digitfor
800°Cormore
Accuracyisnotguaranteedforless
than800°C.
W97Re3-
W75Re25 0.0to2000.0ºC 32to3600ºF ±0.2%ofinstrumentrange±1digit
RTD
JPt100 -200.0to500.0ºC -300.0to1000.0ºF ±0.1%ofinstrumentrange±1digit
(Note1)
-150.00to150.00ºC -200.0to300.0ºF ±0.1%ofinstrumentrange±1digit
Pt100
-200.0to850.0ºC -300.0to1560.0ºF ±0.1%ofinstrumentrange±1digit
(Note1)
-200.0to500.0ºC -300.0to1000.0ºF
-150.00to150.00ºC -200.0to300.0ºF ±0.1%ofinstrumentrange±1digit
Standardsignal
0.400to2.000V
±0.1%ofinstrumentrange±1digit
1.000to5.000V
4.00to20.00mA
DCvoltage/current
0.000to2.000V
0.00to10.00V
0.00to20.00mA
-10.00to20.00mV
0.0to100.0mV
Theaccuracyisthatinthestandardoperatingconditions:23±2°C,55±10%RH,andpower
frequencyat50/60Hz.
Note1: ±0.3°C±1digitintherangebetween0and100°C,±0.5°C±1digitintherange
 between-100and200°C.
Note2: W:W-5%Re/W-26%Re(HoskinsMfg.Co.).ASTME988
•Inputsamplingperiod:50,100,200ms
• Burnout detection:
  FunctionsatTC,RTD,andstandardsignal.
  Upscale,downscale,andoffcanbespecied.
  Forstandardsignal,burnoutisdeterminedtohaveoccurredifitis0.1Vor0.4
 mAorless.
•Inputbiascurrent:0.05µA(forTCorRTD)
•Measuredcurrent(RTD):About0.16mA
• Input resistance:
  TCormVinput:1MΩormore
  Vinput:About1MΩ
  mAinput:About250Ω
•Allowablesignalsourceresistance:
  TCormVinput:250Ωorless
  Effectsofsignalsourceresistance:0.1µV/Ωorless
  DCvoltageinput:2kΩorless
  Effectsofsignalsourceresistance:About0.01%/100Ω
• Allowablewiringresistance:
  RTDinput:Max.150Ω/wire(Theconductorresistancebetweenthethreewires
 shallbeequal.)
  Wiringresistanceeffect:±0.1ºC/10Ω
• Allowableinputvoltage/current:
  TC,mV,mAandRTDinput:±10VDC
  Vinput:±20VDC
  mAinput:±40mA
• Noiserejectionratio:
  Normalmode:40dBormore(at50/60Hz)
  Commonmode:120dBormore(at50/60Hz)
  For 100-240 VAC, the power frequency can be set manually.Automatic
 detectionisalsoavailable.
  For24VAC/DC,thepowerfrequencycanbesetmanually.
• Referencejunctioncompensationerror:
  ±1.0ºC(15to35ºC)
  ±1.5ºC(-10to15ºCand35to50ºC)
• Applicablestandards:JIS/IEC/DIN(ITS-90)forTCandRTD
nStepResponseTimeSpecications
Within500ms(whentheinputsamplingperiodis50msor100ms)
Within1s(whentheinputsamplingperiodis200ms)
(63%ofanalogoutputresponsetimewhenastepchangeof10to90%ofinputspan
isapplied)
nRelayContactOutputSpecications
• Contacttypeandnumberofoutputs:
  Alarm-1to-3output:contactpoint1a;3points(commonisindependent)
  Alarm-4output:contactpoint1c;1point
• Contactrating:
Contactpoint1a(Alarm-1to-3output):240VAC,1Aor30VDC,1A(resistanceload)
Contactpoint1c(Alarm-4output):250VAC,3Aor30VDC,3A(resistanceload)
• Use:Alarmoutput,FAILoutput,etc.
Note:Thiscannotbeusedforasmallloadof10mAorless.
n
RetransmissionOutputSpecications
• Numberofoutputs: Retransmissionoutput; 1,sharedwith15VDClooppower
supply
• Currentoutput:4to20mADCor0to20mADC/loadresistanceof600Ωorless
• Currentoutputaccuracy:±0.1%ofspan(±5%ofspanfor1mAorless)
  Theaccuracyisthatinthestandardoperatingconditions:23±2°C,55±10%RH,
andpowerfrequencyat50/60Hz
n
15VDCLoopPowerSupplySpecications
(Sharedwithretransmissionoutput.)
• Powersupply:14.5to18.0VDC
• Maximumsupplycurrent:About21mA(withshort-circuitcurrentlimitingcircuit)
nContactInputSpecications
• Numberofinputs:2points
• Inputtype:No-voltagecontactinputortransistorcontactinput
• Inputcontactrating:12VDC,10mAormore
  Useacontactwithaminimumon-currentof1mAormore.
• ON/OFFdetection:
  No-voltagecontactinput:
  Contactresistanceof1kΩorlessisdeterminedas“ON”andcontact
  resistanceof50kΩormoreas“OFF.”
Transistor contact input:
  Inputvoltageof2Vorlessisdeterminedas“ON”andleakagecurrentmust
  notexceed100µAwhen“OFF.”
• Minimumstatusdetectionholdtime:Inputsamplingperiod+50ms
• Use:Eventinput
nTransistorContactOutputSpecications
• Numberofoutputs:SeethetableofModelandSufxCodes.
• Outputtype:Opencollector(SINKcurrent)
• Outputcontactrating:Max.24VDC,50mA
• Outputtimeresolution:Min.50ms
• Use:Alarmoutput,FAILoutput,etc.
n24VDCLoopPowerSupplySpecications
• Use:Powerissuppliedtoa2-wiretransmitter.
• Powersupply:21.6to28.0VDC
• Ratedcurrent:4to20mADC
• Maximumsupplycurrent:About30mA(withshort-circuitcurrentlimitingcircuit.)
■ SafetyandEMCStandards
• Safety:CompliantwithIEC/EN61010-1 (CE), approvedbyCAN/CSAC22.2
No.61010-1(CSA).UL61010-1ispendingapproval.
  Installationcategory:CAT.IIPollutiondegree:2
  Measurementcategory:I(CAT.I)
  Ratedmeasurementinputvoltage:Max.10VDC
  Ratedtransientovervoltage:1500V(Note)
Note:ThisisareferencesafetystandardvalueforMeasurementCategoryIofIEC/EN/CSA/
UL61010-1.Thisvalueisnotnecessarilyaguaranteeofinstrumentperformance.
• EMCConformitystandards:
 CEmarking
  EN61326-1ClassA,Table2(Foruseinindustriallocations)
  EN61326-2-3
  EN55011ClassA,Group1
  EN61000-3-2ClassA
  EN61000-3-3
 C-tickmark
  EN55011ClassA,Group1
 Theinstrumentcontinuestooperateatameasurementaccuracyofwithin±20%of
therangeduringtesting.
■ Construction,Installation,andWiring
• Dust-proofanddrip-proof:IP56(forfrontpanel)
• Material:Polycarbonate(Flameretardancy:UL94V-0)
• Casecolor:White(Lightgray)orBlack(Lightcharcoalgray)
• Weight:0.5kgorless
• Externaldimensions(mm):96(W)×48(H)×65(depthfromthepanelface)
  (Depthexcepttheprojectionontherearpanel)
• Installation:Directpanelmounting;mountingbracket,oneeachforrightandleft
mounting
• Panelcutoutdimensions(mm):92+0.8/0(W)×45+0.6/0(H)
• Mountingattitude:Upto30degreesabovethehorizontal.Nodownwardtitlingallowed.
• Wiring:M3screwterminalwithsquarewasher(forsignalwiringandpowerwiring)
■ PowerSupplySpecicationsandIsolation
• Power supply:
  Ratedvoltage:100-240VAC(+10%/-15%),50/60Hz
       24VAC/DC(+10%/-15%)(for/DCoption)
• Power consumption:
15VA(DC:7VA,AC:11VAif/DCoptionisspecied)
• Databackup:Nonvolatilememory
• Powerholduptime:20ms(for100VACdrive)
• Withstandingvoltage
  Betweenprimaryterminalsandsecondaryterminals:2300VACfor1minute
  Betweenprimaryterminals:1500VACfor1minute
  Betweensecondaryterminals:500VACfor1minute
   (Primary terminals:Power*andrelayoutputterminals; Secondaryterminals:
  AnalogI/Osignalterminals,contactinputterminals,communicationterminals
  andfunctionalgroundingterminals.)
 *:Powerterminalsfor24VAC/DCmodelsarethesecondaryterminals.
• Insulationresistance:Between power supply terminals and agroundingterminal
20MΩormoreat500VDC
• Isolationspecications
PV (universal ) input terminals
Alarm-1 relay (contact point a) output terminals
Alarm-2 relay (contact point a) output terminals
Alarm-3 relay (contact point a) output terminals
Contact input terminals (all)
RS-485 communication terminals
24 V DC loop power supply terminals
Contact output (transistor) terminals
Retransmission (analog) output terminals
(not isolated between the analog output terminals)
Internal
circuits
Power
supply
The circuits divided by lines are insulated mutually.
Alarm-4 relay (contact point c) output terminals
■ EnvironmentalConditions
Normal Operating Conditions
• Ambienttemperature:-10to50ºC
• Ambienthumidity:20to90%RH(nocondensationallowed)
• Magneticeld:400A/morless
• Continuousvibrationat5to9Hz:Halfamplitudeof1.5mmorless,1oct/minfor90
minuteseachinthethreeaxisdirections
 Continuousvibrationat9to150Hz:4.9m/s2orless,1oct/minfor90minuteseach
inthethreeaxisdirections
• Short-periodvibration:14.7m/s2, 15 seconds or less
• Shock:98m/s2or less, 11 ms
• Altitude:2000morlessabovesealevel
• Warm-uptime:30minutesormoreafterthepoweristurnedon
• Startuptime:Within10seconds
 *: TheLCD(aliquidcrystaldisplay)isusedforadisplayportionofthisproduct.
 TheLCDhasacharacteristicthatthedisplayactionbecomeslateatthelow
temperature.
Transportation and Storage Conditions
• Temperature:-25to70ºC
• Temperaturechangerate:20ºC/horless
• Humidity:5to95%RH(nocondensationallowed)
Effects of Operating Conditions
• Effectofambienttemperature:
  VoltageorTCinput:±1µV/ºCor±0.01%ofF.S./ºC,whicheverislarger
  Currentinput:±0.01%ofF.S./ºC
  RTDinput:±0.05ºC/ºC(ambienttemperature)orless
  Analogoutput:±0.02%ofF.S./ºCorless
• Effectofpowersupplyvoltageuctuation
  Analoginput:±0.05%ofF.S.orless
  Analogoutput:±0.05%ofF.S.orless
  (Eachwithinratedvoltagerange)

IM 05P03D21-11EN page 3/8
5. How to Connect Wires
WARNING
• Wiring work must be carried out by a person with basic electrical
knowledge and practical experience.
• Be sure to turn OFF the power supply to the indicator before
wiring to avoid an electric shock. Use a tester or similar device
to ensure that no power is being supplied to a cable to be
connected.
• As a safety measure, always install a circuit breaker (an IEC
60947-compatible product, 5 A, 100 V or 220 V AC) in an easily
accessible location near the instrument. Moreover, provide
indication that the switch is a device for turning off the power to
the instrument.
• Install the power cable keeping a distance of more than 1 cm
from other signal wires.
• The power cable is required to meet the IEC standards concerned
or the requirements of the area in which the instrument is being
installed.
• Wiring should be installed to conform to NEC (National Electrical
Code: ANSI/NFPA-70) or the wiring construction standards in
countries or regions where wiring will be installed.
• For the alarm relay output and power terminal connections, use
heat-resistant cables.
• Since the insulation provided to each relay output terminal is
Functional insulation, provide Reinforced insulation to the
external of the device as necessary. (Refer to the drawing below.)
This product
Functional
insulation
A safety
voltage circuit
A safety
voltage circuit
This product
Reinforced insulation
Reinforced insulation
Functional
insulation
A hazardous
voltage circuit
A hazardous
voltage circuit
A safety
voltage circuit
A safety
voltage circuit
This product
Reinforced insulation
Reinforced insulation
Functional
insulation
A hazardous
voltage circuit
A hazardous
voltage circuit
A hazardous
voltage circuit
A hazardous
voltage circuit
CAUTION
• Provide electricity from a single-phase power supply. If the
power is noisy, install an isolation transformer on the primary
side, and use a line filter on the secondary side. When measures
against noise are taken, do not install the primary and secondary
power cables close to each other.
• If there is a risk of external lightning surges, use a lightning
arrester etc.
• For TC input, use shielded compensating lead wires for wiring.
For RTD input, use shielded wires that have low conductor
resistance and cause no significant differences in resistance
between the three wires.
• Since the alarm output relay has a life span (resistance load of
100,000 times), use the auxiliary relay to perform ON/OFF control.
• The use of inductance (L) loads such as auxiliary relays, motors
and solenoid valves causes malfunction or relay failure; always
insert a CR filter for use with alternating current or a diode for
use with direct current, as a spark-removal surge suppression
circuit, into the line in parallel with the load.
• After completing the wiring, the terminal cover is recommended
to use for the instrument.
● RecommendedCrimp-onTerminalLugs
(A)
(F)
(ød)
5.5 3.3
 Recommendedtighteningtorque:0.6N·m
 Applicablewiresize:Powersupplywiring1.25mm2or more
Applicable terminal lug Applicable wire size mm2(AWG#) (φd) (A) (F)
M3 0.25to1.65(22to16) 3.3 5.5 4.2
● CableSpecicationsandRecommendedCables
Purpose Name and Manufacturer
Power supply, relay contact outputs 600VGradeheat-resistantPVCinsulatedwires,JISC
3317(HIV),0.9to2.0mm2
Thermocouple Shieldedcompensatingleadwires,JISC1610
RTD Shieldedwires(three/fourconductors),UL2482(HitachiCable)
Othersignals(otherthancontactinput/output) Shielded wires
Othersignals(contactinput/output) Unshieldedwires
RS-485communication Shielded wires
DC Relay Wiring
R
External DC power supply
Relay
O.C
UM33A
UM’s contact
Diode
(Mount it directly
to the relay coil
terminal (socket).)
Relay
(Use one with a relay coil rating
less than the UM’s contact rating.)
AC Relay Wiring
UM33A
R
UM’s contact CR filter
(Mount it directly
to the relay coil
terminal (socket).)
External AC power supply
Relay
(Use one with a relay coil
rating less than the UM’s
contact rating.)
6. Terminal Wiring Diagrams
CAUTION
• Do not use an unassigned terminal as the relay terminal.
Do not use a 100-240 V AC power supply for the 24 V AC/DC
model; otherwise, the instrument will malfunction.
■ UM33A
301-306
201-212
101-112
306 305 304 303 302 301
212 211 210 208 207 204 203
112 111 110 109 106 105 104108 107 103
202 201
102 101
E1-terminal area
PV
PV input
(Equipped
as standard)
TC input


202
203
RTD input
A
B
b
201
202
203
Voltage (mV, V) input


202
203
Current (mA) input

203
204
Factory default: PV input type is undefined.
RET
Retransmission output
(Equipped as standard)
Retransmission output
4-20 mA DC or
0-20 mA DC


Default: 4-20 mA DC
Default: PV
retransmission
Load resistance 600 Ωor less
207
208
15 V DC loop power supply
14.5-18.0 V DC
(Max. 21 mA DC)


207
208
Can be used for 15 V DC loop
power supply when not used for
retransmission output.
ALM
(Equipped
as standard)
Contact output
External contact output (relay)
AL3
AL2
AL1
Relay contact rating: 240 V AC, 1 A
30 V DC, 1 A (resistance load)
Alarm-3 output
(PV high limit)
Alarm-2 output
( PV low limit)
Alarm-1 output
PV high limit
Common
Common
Common
UM
104
105
106
107
108
109
ALM4
(Suffix code:
Type 2=1, 2 or 3)
Contact output
Contact rating: 250 V AC, 3 A
30 V DC, 3 A (resistance load)
AL4
(24 V AC/DC power supply:
Optional suffix code /DC)
Power supply
Allowable range:
100-240 V AC (±10%)
(free v(oltage)
50/60 Hz shared
100-240 V AC power supply
N
L
110
111
112
24 V AC/DC power supply


110
111
112
N
L
RS-485
RSB(+)
RSA(-)
SG
RS - 485 communication/24 V DC loop power supply

24 V DC loop power supply
21.6-28.0 V DC
(Max. 30 mA DC)

301
302
303
305
306
RS485/LPS24
(Suffix code: Type 2=1 and
with optional suffix code /LP)

24 V DC loop power supply
21.6-28.0 V DC
(Max. 30 mA DC)

24 V DC loop power supply
(Suffix code: Type 2=0 or 2
and with optional suffix code
/LP)
305
306
LPS24
RS-485
SDB(+)
SDA(-)
RDB(+)
RDA(-)
SG
RS - 485 communication
301
302
303
304
305
RS485
(Suffix code:
Type 2=1 and
without optional
suffix code /LP)
(Suffix code: Type 2=3)
Contact output
External contact output
DO12
DO11
DO13
DO14
DO15
COM
Common
UM
301
302
303
304
305
306
DO
Transistor contact rating: 24 V DC, 50 mA
The function of each contact output can be changed.
Alarm-6 output
( PV low limit)
Alarm-5 output
(PV high limit)
Alarm-8 output
( PV low limit)
FAIL
Alarm-7 output
(PV high limit)
DI (Equipped as standard)
Contact input
Contact rating: 12 V DC, 10 mA or more
External contact input
DI2
DI1
COM
Common
DI2
DI1
COM
+5V
+5V
No-voltage
contact Transistor
contact
UM UM
210
211
212
210
211
212
The function of each contact input can be changed.
ON: PV peak and bottom values reset
OFF → ON: Latch release
101
102
Relay contact output
103
NC
NO
COM
Alarm-4
output
( PV low limit)
AL4

IM 05P03D21-11EN page 4/8

IM 05P03D21-11EN page 5/8
Contents
1. NamesandFunctionsofDisplayParts
2. QuickSettingFunction(SettingofInputandOutput)
3. SettingAlarmType
1. Names and Functions of Display Parts
（1）
（2）
（3）（4）
（5）
（11）
（8）
（6）
（7）
（13）
（12）
（10）
（9）
No.ingure Name Description
(1) PVdisplay
(whiteorred)
DisplaysPV.
Displaysanerrorcodeifanerroroccurs.
DisplaysthescrollingguideintheMenuDisplayandParameter
SettingDisplaywhentheguidedisplayON/OFFissettoON.
(2) Groupdisplay(green) Displaysagroupnumber.
(3) Symboldisplay(orange) Displaysaparametersymbol.
(4) Datadisplay(orange) Displaysaparametersetpointandmenusymbol.
(5) Eventindicator
(orange)
Litwhenthealarms1to8occur.
Eventdisplaysotherthanalarmscanbesetbytheparameter.
(6) Keynavigationindica-
tor(green)
LitorblinkswhentheUp/DownorLeft/Rightarrowkeyoperation
ispossible.
(7) Parameterdisplaylevel
indicator(green)
Displaysthesettingconditionsoftheparameterdisplaylevelfunc-
tion.
Parameter display level EASY PRO
Easysettingmode Lit Unlit
Standardsettingmode Unlit Unlit
Professionalsettingmode Unlit Lit
(8) Securityindicator(red) Litifapasswordisset.Thesetupparametersettingsarelocked.
No.ingure Name Description
(9) DISPkey
UsedtoswitchtheOperationDisplays.
PressthekeyintheOperationDisplaytoswitchtheprovided
SELECTDisplays.
PressthekeyintheMenuDisplayorParameterSettingDisplay
toreturntotheOperationDisplay.
(10) PARAkey
Holddownthekeyfor3secondstomovetotheOperation
ParameterSettingDisplay.
HolddownthekeyandtheLeftarrowkeysimultaneouslyfor3
secondstomovetotheSetupParameterSettingDisplay.
PressthekeyintheParameterSettingDisplaytoreturntothe
MenuDisplay.Pressthekeyoncetocanceltheparameterset-
ting(setpointisblinking).
(11)
SET/ENTERkey
Up/Down/Left/Right
arrow keys
SET/ENTERkey
PressthekeyintheMenuDisplaytomovetotheParameter
SettingDisplayoftheMenu.PressthekeyintheParameter
SettingDisplaytotransfertotheparametersettingmode
(setpointisblinking),andtheparametercanbechanged.
Pressthekeyduringparametersettingmodetoregisterthe
setpoint.
Up/Down/Left/Rightarrowkeys
PresstheLeft/RightarrowkeysintheMenuDisplaytoswitch
theDisplays.
PresstheUp/DownarrowkeysintheParameter
SettingDisplaytoswitchtheDisplays.
PresstheUp/Downarrowkeysduringparametersettingmode
(setpointisblinking)tochangeasetpoint.
PresstheLeft/Rightarrowkeysduringparametersettingmode
(setpointisblinking)tomovebetweendigitsaccordingtotheparameter.
(12) Light-loaderinterface
Itisthecommunicationinterfacefortheadaptercableusedwhen
settingandstoringparametersfromaPC.TheLL50AParameter
SettingSoftware(soldseparately)isrequired.
(13) Userfunctionkeys Fnkey.Theusercanassignafunctiontothekey.Thefunctionis
setbytheparameter.
Note: Thecommunicationconnector(maintenanceport)forLL50AParameterSettingSoftwareis
on the side of the unit.
2. Quick Setting Function (Setting of Input and Output)
TheQuicksettingfunctionisafunctiontoeasilysetthebasicfunctionoftheindicator.
TurnontheindicatortostarttheQuicksettingfunction.
Thisfunctionallowsyoutoeasilysettheinput,andquicklystartthealarmaction.
Theitems(parameters)tobesetbyQuicksettingfunctionareasfollows.
(1)Inputfunction(PVinputtype,range,scale(atvoltageinput),etc.)
Afterturningontheindicator,rstdecidewhetherornottousetheQuicksettingfunction.
Operation in Initial Display
· PresstheSET/ENTERkeywhileYESisdisplayedtostarttheQuicksettingfunction.
· IfyouchangeYES toNO and presstheSET/ENTERkey,OperationDisplaywill
appearwithoutstartingtheQuicksettingfunction.
Operation for Setting
· Toselecttheparametersettingdisplayedastheinitialvalue,presstheDownarrow
keytomovetothenextparameter.
· Tochangeandset theparametersetting,pressthe SET/ENTERkeyto startthe
setpointblinking.The blinkingstateallowsyoutomakechanges(setting mode).
UsetheUp/Down/Left/Rightarrowkeystochangethesetpoint.PresstheSET/EN-
TERkeytoregisterthesetting.
■ MakingSettingsUsingQuickSettingFunction
Example: Setting to thermocouple type K (range of 0.0 to 500.00C).
Forthedetailedprocedureandswitchingofdisplays,see"FlowofQuickSetting
Function"below.Fortheparameterstoset,seethenextpage.
(1)PresstheSET/ENTERkeywhileYESforQSM(Quicksettingmode)isdisplayed.
(2)SetthePVinputtypeparameter(IN)toK1(-270.0to1370.00C).
(3)SetthePVinputunitparameter(UNIT)toC(DegreeCelsius).
(4)SetthemaximumvalueofPVinputrangeparameter(RH)to500.0.
(5)SettheminimumvalueofPVinputrangeparameter(RL)to0.0.
(6)Finally,EXITisdisplayed.ChangeNOtoYESandpresstheSET/ENTERkeyto
completethesetup.OperationDisplayappears.
■ FlowofQuickSettingFunction
InQuicksettingmode,theparameterguideappearsonPVdisplay.
Thisguidecanbeturnedon/offwiththeFnkey.
8
1.
2.
3.
4.
5.
6.
8.
9.
10.
11.
7.
8
8
8
8
Power-on
Quick setting starts
The PV input type
parameter (IN) is
displayed.
Initial value: OFF
OFF blinks.
Blinking allows you to
change the setting.
K1 is displayed.
K1 has been registered.
The last digit of the upper limit value blinks.
The parameter RH (maximum value of PV input
range) has been changed to 500.0.
The setpoint for the parameter RH has been
registered.
The PV input unit parameter (UNIT) is displayed.
Initial value: C (Degree Celsius)
Select NO with
the Down arrow
key and press
the SET/ENTER
key.
Press the SET/ENTER key while YES
is displayed to start the Quick setting.
[YES]
[NO]
Press the SET/ENTER key.
Press the SET/ENTER key.
Press the SET/ENTER key.
Press the SET/ENTER key.
Press the Up arrow key.
Select NO to return to
the Operation Display.
Press the Down arrow key.
Press the Down arrow key.
Press the Down arrow key.
The upper limit value of the setting range is displayed
for the parameter RH (maximum value of PV input
range).
Change the setpoint using the Up/Down
arrow keys to increase and decrease the
value and the Left/Right arrow keys to move
between digits.
Finally, EXIT is displayed.
Press the SET/ENTER key to swtich to the
setting mode.
Change NO to YES and press the
SET/ENTER key to complete the setup of
the basic function.
Operation Display appears.
The Quick setting function continues in the
NO state.
Operation Display
Displays the
measured input
value (PV).
Follow the same procedure to set RL.
Operation
Guide
Initial Settings
UM33A
Digital Indicator with Alarms
Operation Guide
This operation guide describes basic settings and operations of the UM33A.
For details of each function, see the electronic manual.
The scrolling guide is displayed on PV display in the Parameter Setting Display.
This guide can be turned on/off with the Fn key.
3. Setting Alarm Type
Thefollowingoperatingprocedureshowsanexampleofchangingthealarm-1type
(factorydefault:PVhighlimitalarm)toPVlowlimitalarm.
1.
2.
3.
4.
5.
6.
8
AL menu is displayed.
ALRM menu is displayed.
Show the Operation Display.
Hold down the key for 3 seconds.
Press the Right arrow key.
Press the SET/ENTER key.
Press the SET/ENTER key.
Press the SET/ENTER key.
The parameter AL1 (alarm-1 type) is
displayed.
The last digit of the setpoint blinks.
Change the setpoint using the Up/Down arrow keys
to increase and decrease the value and the
Left/Right arrow keys to move between digits.
The alarm-1 type setpoint 02 (PV low limit) is
registered.
After the setup is completed, press the DISP key
once to return to the Operation Display.
● To change the alarm type, change the last 2 digits of the 5-digit
value.
● Stand-by action and excitation are turned on or off by selecting 1 or
0. (See “Setting Display of Alarm Type.”)
● For the latch action, see User’ s Manual.
Symbol Stand-by action
Energized/De-energized
Latch action
- -
No alarm (00)
Alarm Action (De-energized)
PV high limit (01)
PV low limit (02)
PV velocity (29)
Fault diagnosis alarm (30)
FAIL (31)
Alarm Type (Alarm Setpoint) Alarm Action (Energized)
Hysteresis
Alarm setpoint PV
Closed
(lit) Open (unlit)
Alarm setpoint
Hysteresis
PV
Closed
(lit)
Open
(unlit)
Hysteresis
Alarm setpoint PV
Open
(lit)Closed (unlit)
Alarm setpoint
Hysteresis
PV
Open
(lit)
Closed
(unlit)
Burnout of PV input, ADC failure, RJC error.
For the factory default, the contact output is turned ON in normal operation,
OFF at the time of FAIL. Alarm output: OFF
Note 1: “Open/closed” shows status of relay contact, and “lit/unlit” shows status of EV (event) lamp.
Setting Display of Alarm Type Stand-by Action
Energized (0) / De-energized (1)
Alarm type
Without (0) or With (1)
Stand-by action
Latch action (0/1/2/3/4)
See User’s Manual.
PV low limit
alarm setpoint
Treated
as normal
ºC
Power-on Time
The alarm output does not turn on
in this region even if the PV valule
is below PV low limit alarm setpoint.
Normal Abnormal
The alarm output
turns on.
8
1.
2.
3.
4.
5.
6.
8.
9.
10.
11.
7.
8
8
8
8
Power-on
Quick setting starts
The PV input type
parameter (IN) is
displayed.
Initial value: OFF
OFF blinks.
Blinking allows you to
change the setting.
K1 is displayed.
K1 has been registered.
The last digit of the upper limit value blinks.
The parameter RH (maximum value of PV input
range) has been changed to 500.0.
The setpoint for the parameter RH has been
registered.
The PV input unit parameter (UNIT) is displayed.
Initial value: C (Degree Celsius)
Select NO with
the Down arrow
key and press
the SET/ENTER
key.
Press the SET/ENTER key while YES
is displayed to start the Quick setting.
[YES]
[NO]
Press the SET/ENTER key.
Press the SET/ENTER key.
Press the SET/ENTER key.
Press the SET/ENTER key.
Press the Up arrow key.
Select NO to return to
the Operation Display.
Press the Down arrow key.
Press the Down arrow key.
Press the Down arrow key.
The upper limit value of the setting range is displayed
for the parameter RH (maximum value of PV input
range).
Change the setpoint using the Up/Down
arrow keys to increase and decrease the
value and the Left/Right arrow keys to move
between digits.
Finally, EXIT is displayed.
Press the SET/ENTER key to swtich to the
setting mode.
Change NO to YES and press the
SET/ENTER key to complete the setup of
the basic function.
Operation Display appears.
The Quick setting function continues in the
NO state.
Operation Display
Displays the
measured input
value (PV).
Follow the same procedure to set RL.
■ Parameterstobeset
Input Function
Parameter Symbol Name of Parameter Setting Range
IN PVinputtype
OFF:Disable
K1:-270.0to1370.00C/-450.0to2500.0 0F
K2:-270.0to1000.00C/-450.0to2300.0 0F
K3:-200.0to500.00C/-200.0to1000.0 0F
J:-200.0to1200.00C/-300.0to2300.0 0F
T1:-270.0to400.00C/-450.0to750.0 0F
T2:0.0to400.00C/-200.0to750.0 0F
B:0.0to1800.00C/32to3300 0F
S:0.0to1700.00C/32to3100 0F
R:0.0to1700.00C/32to3100 0F
N:-200.0to1300.00C/-300.0to2400.0 0F
E:-270.0to1000.00C/-450.0to1800.0 0F
L:-200.0to900.00C/-300.0to1600.0 0F
U1:-200.0to400.00C/-300.0to750.0 0F
U2:0.0to400.00C/-200.0to1000.0 0F
W:0.0to2300.00C/32to4200 0F
PL2:0.0to1390.00C/32.0to2500.0 0F
P2040:0.0to1900.00C/32to3400 0F
WRE:0.0to2000.00C/32to3600 0F
JPT1:-200.0to500.00C/-300.0to1000.0 0F
JPT2:-150.00to150.000C/-200.0to300.0 0F
PT1:-200.0to850.00C/-300.0to1560.0 0F
PT2:-200.0to500.00C/-300.0to1000.0 0F
PT3:-150.00to150.000C/-200.0to300.0 0F
0.4-2V:0.400to2.000V
1-5V:1.000to5.000V
4-20:4.00to20.00mA
0-2V:0.000to2.000V
0-10V:0.00to10.00V
0-20:0.00to20.00mA
-1020:-10.00to20.00mV
0-100:0.0to100.0mV
UNIT PVinputunit -:Nounit,C:DegreeCelsius
-:Nounit,--:Nounit,---:Nounit,F:DegreeFahrenheit
RH Maximumvalueof
PVinputrange
Dependsontheinputtype.
-Fortemperatureinput-
Setthetemperaturerangethatisactuallydisplayed.
(RL<RH)
-Forvoltage/currentinput-
Settherangeofavoltage/currentsignalthatisapplied.
Thescaleacrosswhichthevoltage/currentsignalis
actuallydisplayedshouldbesetusingthemaximumvalue
ofinputscale(SH)andminimumvalueofinputscale(SL).
(Inputisalways0%whenRL=RH.)
RL Minimumvalueof
PVinputrange
SDP
PVinputscale
decimal point
position
0:Nodecimalplace
1:Onedecimalplace
2: Two decimal places
3: Three decimal places
4: Four decimal places
SH Maximumvalueof
PVinputscale -19999to30000,(SL<SH),|SH-SL|≤30000
SL Minimumvalueof
PVinputscale
Note1:SDP,SH,andSLaredisplayedonlyforvoltage/currentinput.
Note2:W:W-5%Re/W-26%Re(HoskinsMfg.Co.),ASTME988

IM 05P03D21-11EN page 6/8
Contents
1. Monitoring-purposeOperationDisplaysAvailableduringOperation
2. SettingAlarmSetpoint
3. Troubleshooting
1. Monitoring-purpose Operation Displays Available during Opera tion
■ OperationDisplaySwitchingDiagram
8 8
PV Display SELECT Displays (1 to 5)
PresstheDISPkeytoshowSELECTDisplay-1to-5conditionally.
FortheregistrationoftheSELECTDisplays,seeUser’sManual.
Operation
Guide
UM33A
Digital Indicator with Alarms
Operation Guide
This operation guide describes key entries for operating the UM33A.
For operations using external contact inputs, see “DI” of “6. Terminal Wiring Diagrams”
in “Installation and Wiring.”
If you cannot remember how to carry out an operation during setting, press the
DISP key once. This brings you to the display (Operation Display) that
appears at power-on.
The scrolling guide is displayed on PV display in the Parameter Setting Display.
This guide can be turned on/off with the Fn key.
Operations
2. Setting Alarm Setpoint
Thefollowingoperatingprocedureshowsanexampleofsettingthealarm-1setpoint
to180.0.
Beforesettingthealarmsetpoint,checkthealarmtype.
Tochangethealarmtype,see“3.SettingAlarmType”in“Initialsettings”ofthis
manual.
1.
2.
3.
4.
5.
6.
8
8
AL menu is displayed.
Display the parameter that need to be changed.
Blinks during the change.
Show the Operation Display.
Hold down the PARA key for 3 seconds.
Press the SET/ENTER key.
Press the SET/ENTER key.
Press the SET/ENTER key.
The parameter A1 is displayed.
A1 to A8 represent the alarm-1 to -8
setpoints.
Each parameter can be changed in the
Parameter Setting Displays of alarms
using Up/Down arrow keys .
Change the setpoint using the Up/Down arrow keys to
increase and decrease the value and the Left/Right
arrow keys to move between digits.
The setpoint has been registered.
After the setup is completed, press
the DISP key once to return to the
Operation Display.
3. Troubleshooting
■TroubleshootingFlow
IftheOperationDisplaydoesnotappearafterturningontheindicator’spower,check
theproceduresinthefollowingowchart.
Ifaproblemappearstobecomplicated,contactoursalesrepresentatives.
■RemediesifPowerFailureOccursduringOperations
• Instantaneous power failure within 20 ms.
 Apowerfailureisnotdetected.Normaloperationcontinues.
• Power failure for less than about 5 seconds, or for about 5 seconds or more.
 Affectsthe"settings"and"operationstatus."
 Fordetails,seeUser'sManual.
NOTE
Write down the settings
of parameters for a repair
request.
Is the indicator
defective?
Contact us for repair. Problem solved.
No communication
capability
Completely
inactive?
Yes
Yes
Yes
No
No
No
Key
operation
failure?
Yes
No
Yes
Check wiring of the
power terminals.
Check the key lock
setting.
Display
failure?
*
Yes
No
Turn off power, and
then turn it on again.
I/O signal
failure?
Yes
No
Check the
supply voltage.
Check the
specifications and polarity
of connected devices .
Check the communication-
related parameters.
Check the specifications
of communication
devices.
Check the
communication wiring.
Communication
failure?
No
With
communi-
cation?
Yes
Yes
Normal?
Is the
key locked?
Check the specifications
of the indicator.
Yes
No Correct?
Correct the error(s).
Cancel the setting.
Check the I/O specifications
of the indicator.
* The LCD (a liquid crystal display) is used for a
display portion of this product.
The LCD has a characteristic that the display action
becomes late at the low temperature.
Additionally, the luminance and contrast degradation
are caused due to aged deterioration.
However, the function is not affected.
nErrors at Power On
Theerrorsshownbelowmayoccurinthefaultdiagnosiswhenthepoweristurnedon.(FordetailsofSetpointdisplayandinput/outputactionwheneacherroroccurs,seeUser’sManual.)
PV display
(Operation
Display)
Setpoint display
(Operation Display)
Status indicator
(Operation Display)
Parameter that displays error
details Error description Cause and diagnosis Remedy
Indication off Indication off — — FaultyMCURAM/MCUROM MCURAM/MCUROMarefailed. Faulty.
Contactusforrepair.
ERR
SYS-----
—
— System data error System data is corrupted. Faulty.
Contactusforrepair.
PAR0004
(foruserdefaultvalueerroronly)
Setupparameter(PA.ER)
User(parameter)defaultvalue
error
Userparameteriscorrupted.
Initializedtofactorydefaultvalue. Checkandreconguretheinitialized
settingparameters.Errorindicationis
erased when the power is turned on
again.
PAR0010
(forsetupparametererroronly)
Setup parameter error Setup parameter data is corrupted.
Initializedtouserdefaultvalue.
PAR0020
(foroperationparametererroronly)
Operationparametererror Operationparameterdataiscorrupted.
Initializedtouserdefaultvalue.
SLOT0001 Setupparameter(OP.ER)
Nonrespondinghardwareof
extendedfunction(E1-terminal
area)
Inconsistence of system data and hardware of
extendedfunction.
Nonrespondingcommunicationbetweenhardware
ofextendedfunction(E1-terminalarea).
Faulty.
Contactusforrepair.
Normal
indication Normalindication
Rightmostdecimalpoint
onPVdisplayblinks. Setupparameter(PA.ER)
Calibrationvalueerror
Initializedtocalibrateddefaultvaluebecause
ofcorruptedfactorydefaultvalue.
Faulty.
Contactusforrepair.
Rightmostdecimalpoint
onSymboldisplayblinks.
FaultyFRAM Datawriting(storing)toFRAMisimpossible.
nErrors during Operation
Theerrorsshownbelowmayoccurduringoperation.(Forinput/outputactionwheneacherroroccurs,seeUser’sManual.)
PV display
(Operation
Display)
Setpoint display
(Operation Display)
Status indicator
(Operation Display)
Parameter that displays
error details Error description Cause and diagnosis Remedy
AD.ERR Normalindication —Setupparameter(AD1.E) AnaloginputterminalADCerror
•PVinput AnaloginputterminalADvalueerror Faulty.
Contactusforrepair.
RJC.E
(DisplaysRJC.
EandPV
alternately.)
Normalindication —Setupparameter(AD1.E) UniversalinputterminalRJCerror
•PVinput UniversalinputterminalRJCerror
Faulty.
Contactusforrepair.
SettheparameterRJCtoOFFtoerase
error indication.
B.OUT Normalindication —
Setupparameter(AD1.E) Analoginputterminalburnouterror
•PVinput Analoginputterminalsensorburnout
Checkwiringandsensor.
Errorindicationiserasedinnormal
operation.
Setupparameter(PV1.E) PVinputburnouterror BurnoutofanaloginputconnectedtoPV
Checkwiringandsensorofconnected
analoginputterminals.
Errorindicationiserasedinnormal
operation.
OVER
-OVER Normalindication —Setupparameter(PV1.E)
PVinputover-scale
PVinputunder-scale
(PVvaluesoutof-5to105%)
PVinputisoutof-5to105%.Alsooccurs
whenthedataoutofrangewhichisthe
ladder calculation result is input.
Checkanaloginputvalueorladder
program.
Normal
indication
0.00000000
(Decimalpointontheleftof
theSymboldisplayblinks)
—Setupparameter(OP.ER) Communicationerror
(RS-485communication)
Framingparityerror
Bufferoverow
Inter-charactertime-out
Checksumerror(PClinkcommunicationwith
checksum)
CRCcheckerror(Modbus/RTU)
LRCcheckerror(Modbus/ASCII)
Checkthecommunicationparameters.
Recoveryatnormalreceipt.
Holddownanykeytostopblinking.
Normal
indication Normalindication
Rightmostdecimalpointon
Symboldisplayblinks.
Setupparameter(PA.ER) FaultyFRAM Writing(storing)datatoFRAMisimpossible. Faulty.Contactusforrepair.
Undened Undened — — FaultyMCU/DCU
(ROM/RAMerror,corrupted) MCU/DCUiscorrupted. Faulty.Contactusforrepair.

IM 05P03D21-11EN page 7/8
Operation Parameters
HolddownthePARAkeyfor3secondstomovefromtheOperationDisplaytotheOp-
erationParameterSettingDisplay.PresstheDISPkeyoncetoreturntotheOperation
Display.
Menu
Hold down PARA key
for 3 sec.
DISP key
SET/ENTER key
PARA key
key key key
key key
Operation Dsipaly
Parameter
Parameter
Parameter
Parameter
Parameter
Parameter
END
Menu
END
Menu END
END
Menu Display and
Parameter Setting
Display are changed
in a circular pattern.
Move to the Setup Parameter Setting Display:
Hold down the PARA key and the Left arrow key simultaneously for 3 sec.
Operation for Setting
· Toselecttheparametersettingdisplayedastheinitialvalue,presstheDownarrow
keytomovetothenextparameter.
· Tochangeandsettheparametersetting,presstheSET/ENTERkeytostarttheset-
pointblinking.Theblinkingstateallowsyoutomakechanges(settingmode).Usethe
Up/Down/Left/Rightarrowkeystochangethesetpoint.PresstheSET/ENTERkeyto
registerthesetting.
Notethattherearesomeparameterswhicharenotdisplayeddependingonthemodelandsuffix
codes.
nAlarm Setpoint Setting Parameter
Menusymbol: (AL)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
to
(A1toA8)
Alarm-1to-8setpoint
SetadisplayvalueofsetpointofPV
alarmorvelocityalarm.
-19999to30000(Setavaluewithin
theinputrange.)
Decimalpointpositiondependson
the input type
0Table
below EASY
Forthealarmsetpointparameter,alarm-1 to -8 are displayed for the factory default.
ThenumberofalarmscanbechangedusingthesetupparameterALNO. (number of
alarms).Tochangethenumberofalarms,seeUser'sManual.
Usethefollowingtabletorecordalarmsetpoints.
Parameter Setpoint Parameter Setpoint
A1 A5
A2 A6
A3 A7
A4 A8
nAlarm Function Setting Parameter
Menusymbol: (ALRM)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
to
(AL1toAL8)
Alarm-1to8type
Example:Alarm-1
Stand-by
action
Latch action
Energized/
De-energize
Alarm
type
Seta5-digitvalueinthefollowing
order.
[Alarmtype:2digits(seebelow)]+
[Without(0)orWith(1)Stand-byac-
tion]+[Energized(0)orDe-energized
(1)]+[Latchaction(0/1/2/3/4)]
Forlatchaction,seeUser'sManual.
AL1,
AL3,
AL5,
AL7:
PVhigh
limit(01)
Without
Stand-
by
action
(0)
Ener-
gized(0)
Latch
action
(0)
AL2,
AL4,
AL6,
AL8:
PVlow
limit(02)
Without
Stand-
by
action
(0)
Ener-
gized
(0)
Latch
action
(0)
Table
below
EASY
Alarmtype:2digits
00:Disable
01:PVhighlimit
02:PVlowlimit
29:PVvelocity
30:Faultdiagnosis
31:FAIL
to
(VT1toVT8)
PVvelocityalarmtime
setpoint1to8 0.01to99.59(minute.second) 1.00
to
(HY1toHY8)
Alarm-1to-8hysteresis
Setadisplayvalueofsetpointof
hysteresis.
-19999to30000(Setavaluewithin
theinputrange.)
Decimalpointpositiondependson
the input type.
Whenthedecimalpointpositionfor
theinputtypeissetto"1",theinitial
valueofthehysteresisis"1.0".
10
to
(DYN1toDYN8)
Alarm-1to-8On-delay
timer
AnalarmoutputisONwhenthedelay
timerexpiresafterthealarmsetpoint
is reached.
0.00to99.59(minute.second)
0.00 STD
Forthealarmfunctionsettingparameter,8alarmsaredisplayedforthefactorydefault.
ThenumberofalarmscanbechangedbythesetupparameterALNO. (numberof
alarms).Tochangethenumberofalarms,seeUser'sManual.
Parameter n=1 n=2 n=3 n=4 n=5 n=6 n=7 n=8
ALn
VTn
HYn
DYNn
n:alarmnumber
nPV-related Setting Parameter
Menusymbol: (PVS)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
(BS) PVinputbias -100.0to100.0%ofPVinputrange
span(EUS)
0.0%
ofPV
input
range
span
EASY
(FL) PVinputlter OFF,1to120s OFF
(PEAK) PVpeakvalue
Displayonly
(-5.0to105.0%ofPVinputrange
(EU))
None
(BOTM) PVbottomvalue None
Setup Parameters
HolddownthePARAkeyandLeftarrowkeysimultaneouslyfor3secondstomove
fromtheOperationDisplayorOperationParameterSetting Display to theSetupPa-
rameterSettingDisplay.
PresstheDISPkeyoncetoreturntotheOperationDisplay.
Menu
DISP key
SET/ENTER key PARA key
key key key
key key
Operation Dsipaly
Parameter
Parameter
Parameter
Parameter
Parameter
Parameter
END
Menu
END
Menu END
END
Menu Display and
Parameter Setting
Display are changed
in a circular pattern.
Move to the Operation Parameter Setting Display:
Hold down the PARA key for 3 sec.
Hold down PARA key and
Left arrow key simultaneously for 3 sec.
Operation for Setting
· Toselecttheparametersettingdisplayedastheinitialvalue,presstheDownarrow
keytomovetothenextparameter.
· Tochangeandsettheparametersetting,presstheSET/ENTERkeytostarttheset-
pointblinking.Theblinkingstateallowsyoutomakechanges(settingmode).Usethe
Up/Down/Left/Rightarrowkeystochangethesetpoint.PresstheSET/ENTERkeyto
registerthesetting.
NotethattherearesomeparameterswhicharenotdisplayeddependingontheModelandSuffixcodes.
nFunction Setting Parameter
Menusymbol: (CTL)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
(SMP) Inputsamplingperiod 50:50ms,100:100ms,200:200ms 50 STD
nPV Input Setting Parameter
Menusymbol: (PV)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
(IN) PVinputtype
OFF:Disable
K1:-270.0to1370.0
0
C/-450.0to2500.0
0
F
K2:-270.0to1000.0
0
C/-450.0to2300.0
0
F
K3:-200.0to500.0
0
C/-200.0to1000.0
0
F
J:-200.0to1200.00C/-300.0to2300.0 0F
T1:-270.0to400.0
0
C/-450.0to750.0
0
F
T2:0.0to400.0
0
C/-200.0to750.0
0
F
B:0.0to1800.00C/32to3300 0F
S:0.0to1700.00C/32to3100 0F
R:0.0to1700.00C/32to3100 0F
N:-200.0to1300.0
0
C/-300.0to2400.0
0
F
E:-270.0to1000.0
0
C/-450.0to1800.0
0
F
L:-200.0to900.0
0
C/-300.0to1600.0
0
F
U1:-200.0to400.0
0
C/-300.0to750.0
0
F
U2:0.0to400.00C/-200.0to1000.0 0F
W:0.0to2300.00C/32to4200 0F
PL2:0.0to1390.0
0
C/32.0to2500.0
0
F
P2040:0.0to1900.0
0
C/32to3400
0
F
WRE:0.0to2000.00C/32to3600 0F
JPT1:-200.0to500.00C/-300.0to1000.0 0F
JPT2:-150.0to150.0
0
C/-200.0to300.0
0
F
PT1:-200.0to850.0
0
C/-300.0to1560.0
0
F
PT2:-200.0to500.0
0
C/-300.0to1000.0
0
F
PT3:-150.00to150.00
0
C/-200.0to300.0
0
F
0.4-2V:0.400to2.000V
1-5V:1.000to5.000V
4-20:4.00to20.00mA
0-2V:0.000to2.000V
0-10V:0.00to10.00V
0-20:0.00to20.00mA
-1020:-10.00to20.00mV
0-100:0.0to100.0mV
OFF EASY
(UNIT) PVinputunit
-:Nounit,C:DegreeCelsius
-:Nounit,--:Nounit,---:Nounit,
F:DegreeFahrenheit
C EASY
(RH)
MaximumvalueofPV
inputrange
Dependsontheinputtype.
-Fortemperatureinput-
Setthetemperaturerangethatis
actuallydisplayed.(RL<RH)
-Forvoltage/currentinput-
Settherangeofavoltage/current
signalthatisapplied.
Thescaleacrosswhichthevoltage
/currentsignalisactuallydisplayed
shouldbesetusingthemaximum
valueofinputscale(SH)and
minimumvalueofinputscale(SL).
(Inputisalways0%whenRL=RH.)
Depends
on the
input type
EASY
(RL)
MinimumvalueofPV
inputrange
(SDP)
PVinputscaledecimal
point position
0:Nodecimalplace
1:Onedecimalplace
2: Two decimal places
3: Three decimal places
4: Four decimal places
Depends
on the
input type
EASY
(SH)
MaximumvalueofPV
input scale -19999to30000,(SL<SH),
|SH-SL|≤30000
Depends
on the
input type
EASY
(SL)
MinimumvalueofPV
input scale
(BSL)
PVinputburnoutaction
OFF:Disable
UP:Upscale
DOWN:Downscale
Depends
on the
input type
STD
W:W-5%Re/W-26%Re(HoskinsMfg.Co.).ASTME988
WRE:W97Re3-W75Re25
nInput Range Setting Parameter
Menusymbol: (MPV)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
(P.UNI) DisplayPVinputunit
-:Nounit
C:DegreeCelsius
-:Nounit
--:Nounit
---:Nounit
F:DegreeFahrenheit
Same
asPV
input
unit
STD
(P.DP)
DisplayPVinputdecimal
point position
0:Nodecimalplace
1:Onedecimalplace
2: Two decimal places
3: Three decimal places
4: Four decimal places
1
(P.RH)
Maximumvalueof
displayPVinputrange
-19999to30000,(P.RL<P.RH),
|P.RH-P.RL|≤30000
Depends
on the
input type
(P.RL)
Minimumvalueofdisplay
PVinputrange
nOutput Setting Parameter
Menusymbol: (OUT)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
(RTS)
Retransmissionoutput
typeofRET
OFF:Disable
PV1:PV
LPS:15VDClooppowersupply
PV1 EASY
(RTH)
Maximumvalueof
retransmission output
scaleofRET
WhenRTS=PV1
RTL+1digitto30000
-19999toRTH-1digit
Decimalpointposition:When
RTS=PV1,decimalpointposition
issameasthatofPVinput.
WhenRTS=PV,decimalpointposition
issameasthatofPVinputscale.
100%
ofPV
input
range
STD
(RTL)
Minimumvalueof
retransmission output
scaleofRET
0%
ofPV
input
range
(RET.A)
RETcurrentoutput
range
4-20:4to20mA
0-20:0to20mA
20-4:20to4mA
20-0:20to0mA
4-20
n
RS-485 Communication Setting Parameter (E1-terminal Area)
Menusymbol: (R485)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
(PSL) Protocol selection
PCL:PClinkcommunication
PCLSM:PClinkcommunication(with
checksum)
LADR:Laddercommunication
MBASC:Modbus(ASCII)
MBRTU:Modbus(RTU)
MBRTU
EASY
(BPS) Baud rate
600:600bps
1200:1200bps
2400:2400bps
4800:4800bps
9600:9600bps
19200:19.2kbps
38400:38.4kbps
19200
(PRI) Parity
NONE:None
EVEN:Even
ODD:Odd
EVEN
(STP) Stopbit 1:1bit,2:2bits 1
(DLN) Datalength 7:7bits,8:8bits 8
(ADR) Address 1to99 1
Operation
Guide
UM33A
Digital Indicator with Alarms
Operation Guide
This operation guide describes the functions of parameters briefly. The parameter
symbols listed are in the order shown on the display in each group of menu symbols.
In addition, each parameter table has a “User Setting” column, where you can record
your setpoints when setting them in the indicator. The scrolling guide is displayed on
PV display in the Parameter Setting Display. This guide can be turned on/off with
the Fn key.
Yokogawa Electric Corporation
Parameters

IM 05P03D21-11EN page 8/8
■KeyActionSettingParameter
Menusymbol: (KEY)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
(Fn)
Userfunctionkey-n
actionsetting
OFF:Disable
LTUP:LCDbrightnessUP
LTDN:LCDbrightnessDOWN
BRI:AdjustLCDbrightness
LCD:LCDbacklightON/OFFswitch
LAT:Latchrelease(ACK)
AL:Alarmsetpointsetting
RST:PVpeakandbottomvalues
reset
RST EASY
■DisplayFunctionSettingParameter
Menusymbol: (DISP)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
(PCMD)
ActivecolorPVdisplay
switch
0:Fixedinwhite
1:Fixedinred
2:Linktoalarm1(AlarmOFF:white,
AlarmON:red)
3:Linktoalarm1(AlarmOFF:red,
AlarmON:white)
4:Linktoalarm1or2(AlarmOFF:
white,AlarmON:red)
5:Linktoalarm1or2(AlarmOFF:
red,AlarmON:white)
6:PVlimit(Withinrange:white,Out
ofrange:red)
7:PVlimit(Withinrange:red,Outof
range:white)
10:LinktoDI(ON:red,OFF:white)
0
EASY
(PCH)
PVcolorchangehigh
limit
SetadisplayvaluewheninPVlimit
orSPdeviation.
-19999to30000(Setavaluewithin
theinputrange.)
Decimalpointpositiondependson
the input type.
0
(PCL) PVcolorchangelowlimit 0
(GUID) GuidedisplayON/OFF OFF:Non-display,ON:Display ON
STD
(ECO) Economymode
OFF:Disable
1:EconomymodeON(Allindications
exceptPVdisplayOFF)
2:EconomymodeON(Allindications
OFF)
3:Brightness10%(wholeindication)
OFF
(BRI) Brightness (Dark)1to5(Bright) 3EASY
(MLSD)
Leastsignicantdigital
maskofPVdisplay
OFF:Withleastsignicantdigit
ON:Withoutleastsignicantdigit OFF STD
■SELECTDisplaySettingParameter
Menusymbol: (CSEL)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
to
(CS1toCS5)
SELECTDisplay-1to-5
registration
Registertheoperationparameter
(excepttheOperaitonMode)thatis
frequentlymodiedtodisplayitinthe
OperationDisplay.
OFF,2301to5000
Forthesettingrange,seeUser's
Manual.
OFF STD
UsethefollowingtabletorecordSELECTDsipalysettingvalue.
Parameter n=1 n=2 n=3 n=4 n=5
CSn
■KeyLockSettingParameter
Menusymbol: (KLOC)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
(COM.W)
Communicationwrite
enable/disable OFF:Enable,ON:Disable OFF
STD
(DATA)
Front panel parameter
data(▼,▲)keylock
OFF:Unlock,ON:Lock
(AvailableforOperationDisplayonly.) OFF
■DIFunctionResistrationParameter
Menusymbol: (DI.SL)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
(RST)
PVpeakandbottom
valuesreset
SetanIrelaynumberofcontactinput.
Set“OFF”todisablethefunction.
Standard terminals
DI1:5025,DI2:5026
5025
STD
(LAT) Latchrelease(ACK) 5026
(LCD)
LCDbacklightON/OFF
switch OFF
(PVRW) PVred/whiteswitch OFF
■AL1-AL4FunctionRegistrationParameter
Menusymbol: (ALM)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
(AL1.S) AL1functionselection
SetanIrelaynumber.Fortheitems
otherthanbelow,seeUser'sManual.
Ex.)Setthenumber4353forAL1.S
to use the alarm 1.
Set“OFF”todisablethefunction.
Nofunction:OFF
Alarm1:4353
Alarm2:4354
Alarm3:4355
Alarm4:4357
Alarm5:4358
Alarm6:4359
Alarm7:4361
Alarm8:4362
FAIL(NormallyON)output:4256
4353
STD
(AL2.S) AL2functionselection 4354
(AL3.S) AL3functionselection 4355
(AL4.S) AL4functionselection 4357
■DOSettingParameter(E1-terminalArea)
Menusymbol: (DO)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
(DO1.S) DO11functionselection
SameasAL1.S
Set“OFF”todisablethefunction
4358
STD
(DO2.S) DO12functionselection 4359
(DO3.S) DO13functionselection 4361
(DO4.S) DO14functionselection 4362
(DO5.S) DO15functionselection 4256
■SystemSettingParameter
Menusymbol: (SYS)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
(R.TM) Restarttimer 0to10s. 0 STD
(FREQ) Powerfrequency AUTO,60:60Hz,50:50Hz AUTO
EASY
(QSM) Quicksettingmode OFF:Disable
ON:Enable ON
(LANG) Guidedisplaylanguage
ENG:English
FRA:French
GER:German
SPA:Spanish
Depe-
nds on
the
model
and
sufx
codes
(PASS) Passwordsetting
0(Nopassword)to65535
Setting“0”means“withoutpassword
protection.”
0
■ ErrorandVersionConrmationParameter(fordisplayonly)
Menusymbol: (VER)
Parameter
symbol Name of Parameter Status record
Display
level
(PA.ER) Parameter error status
EASY
(OP.ER) Optionerrorstatus
(AD1.E) A/Dconvertererrorstatus1
(PV1.E) PVinputerrorstatus
(MCU) MCUversion
(DCU) DCUversion
(ECU1) ECU-1version(E1-terminalarea)
(PARA) Parameterversion
(H.VER) Productversion
(SER1)Serialnumber1
(SER2) Serialnumber2
■ParameterDisplayLevelParameter
Menusymbol: (LVL)
Parameter
symbol Name of Parameter Setting Range Initial value
User
setting
Display
level
(LEVL) Parameterdisplaylevel
EASY:Easysettingmode
STD:Standardsettingmode
PRO:Professionalsettingmode
STD EASY
*ForProfessionalsettingmode,seeUser’sManual.
Trademarks
● Our product names or brand names mentioned in this manual are
the trademarks or registered trademarks of Yokogawa Electric Corporation.
● Adobe, Acrobat, and Postscript are either registered trademarks or trademarks
of Adobe Systems Incorporated.
● We do not use the TM or ® mark to indicate these trademarks or
registered trademarks in this manual.
● All other product names mentioned in this manual are trademarks
or registered trademarks of their respective companies.