YOKOGAWA ADMAG TI Series User manual

ADMAG TI Series
AXG Magnetic Flowmeter
FM (USA) Explosion Protection Type
IM 01E21A03-01EN
1st Edition
IM 01E21A03-01EN
User’s
Manual

IM 01E21A03-01EN
ADMAG TI Series
AXG Magnetic Flowmeter
FM (USA) Explosion Protection Type
IM 01E21A03-01EN 1st Edition
1st Edition: Oct. 2019 (KP)
All right Reserved Copyright © 2019. Yokogawa Electric Corporation
Contents
1. Introduction...................................................................................................1
2. Explosion Protection Type ..........................................................................3
2.1 Technical Data ...................................................................................................... 3
2.2 Cable Entry ........................................................................................................... 7
2.3 Installation ............................................................................................................ 7
2.4 Operation ............................................................................................................ 12
2.5 Maintenance and Repair ................................................................................... 12
2.6 Specic Condition of Use ................................................................................. 12
Revision Information

IM 01E21A03-01EN
1
<1. Introduction> 1
1. Introduction
This manual provides the basic guidelines for
explosion protection type of ADMAG TI (Total
Insight) Series AXG magnetic owmeters.
For the items which are not covered in this manual,
read the applicable user’s manuals and general
specications as listed in IM 01E21A21-01Z1 (Read
Me First). These documents can be downloaded
from the website of YOKOGAWA. To ensure correct
use of the product, read these manuals thoroughly
and fully understand how to operate the product
before maintaining it. For method of checking
the model and specications, read the applicable
general specications in IM 01E21A21-01Z1 (Read
Me First).
Website address: http://www.yokogawa.com/d/doc/
These manuals can be downloaded from the
website of YOKOGAWA or purchased from the
YOKOGAWA representatives.
NOTE
When describing the model name like “AXG###”
in this manual, “###” means any of the following.
For AXG###:
002, 005, 010, 015, 025, 032, 040, 050, 065,
080, 100, 125, 150, 200, 250, 300, 350, 400
Precautions Related to the Protection,
Safety, and Alteration of the Product
The following safety symbol marks are used in this
manual and product.
WARNING
A WARNING sign denotes a hazard. It calls
attention to procedure, practice, condition or the
like, which, if not correctly performed or adhered
to, could result in injury or death of personnel.
CAUTION
A CAUTION sign denotes a hazard. It calls
attention to procedure, practice, condition or the
like, which, if not correctly performed or adhered
to, could result in damage to or destruction of
part or the entire product.
IMPORTANT
An IMPORTANT sign denotes that attention
is required to avoid damage to the product or
system failure.
NOTE
A NOTE sign denotes information necessary
for essential understanding of operation and
features.
The following symbols are used in the product and
the manual to indicate the accompanying safety
precautions:
Protective grounding terminal
Functional grounding terminal (This terminal should
not be used as a protective grounding terminal.)
Alternating current
Direct current
Caution
This symbol indicates that the operator must refer to
an explanation in the user’s manual in order to avoid
the risk of injury or death of personnel or damage to
the product.
• For the protection and safe use of the product
and the system in which this product is
incorporated, be sure to follow the instructions
and precautions on safety that is stated in user's
manual as listed in IM 01E21A21-01Z1 (Read
Me First) whenever you handle the product.
Take special note that if you handle the product
in a manner that violated these instructions,
the protection functionality of the product
may be damaged or impaired. In such cases,
YOKOGAWA does not guarantee the quality,
performance, function, and safety of product.
• Do not modify this product.
• The product should be disposed of in
accordance with local and national legislation/
regulations.

IM 01E21A03-01EN
2
<1. Introduction> 2
Regarding This User’s Manual
• This manual should be provided to the end
user.
• The contents of this manual are subject to
change without prior notice.
• All rights reserved. No part of this manual
may be reproduced in any form without
YOKOGAWA’s written permission.
• YOKOGAWA makes no warranty of any kind
with regard to this manual, including, but not
limited to, implied warranty of merchantability
and tness for a particular purpose.
• If any question arises or errors are found, or if
any information is missing from this manual,
inform the nearest YOKOGAWA sales ofce.
• The specications covered by this manual are
limited to those for the standard type under the
specied model number break-down and do not
cover custom-made products.
• Note that changes in the specications,
construction, or component parts of the
product may not immediately be reected in
this manual at the time of change, provided
that postponement of revisions will not cause
difculty to the user from a functional or
performance standpoint.
• This manual is intended for the following
personnel;
Engineers responsible for installation and wiring
of the instrument.
• To ensure correct use, read this manual and
the applicable user’s manuals as listed in IM
01E21A21-01Z1 (Read Me First) thoroughly
before starting operation. Read the general
specications as listed in IM 01E21A21-01Z1
(Read Me First) for its specication.
Trademark
• All the brands or names of Yokogawa
Electric’s products used in this manual are
either trademarks or registered trademarks of
Yokogawa Electric Corporation.
• All other company and product names
mentioned in this manual are trade names,
trademarks or registered trademarks of their
respective companies.
• In this manual, trademarks or registered
trademarks are not marked with ™ or ®.
For Safe Use of Product
For the protection and safe use of the product and
the system in which this product is incorporated,
be sure to follow the instructions and precautions
on safety that is stated in user's manual as listed
in IM 01E21A21-01Z1 (Read Me First) whenever
you handle the product. Take special note that if
you handle the product in a manner that violated
these instructions, the protection functionality of
the product may be damaged or impaired. In such
cases, YOKOGAWA shall not be liable for any
indirect or consequential loss incurred by either
using or not being able to use the product.

IM 01E21A03-01EN
3
<2. Explosion Protection Type> 3
WARNING
AXG### magnetic owmeter (Integral Flowmeter
or Remote Sensor), and AXG4A Remote
Transmitter are products which have been
certied as explosion protection type products.
Strict limitations are applied to the structures,
installation locations, external wiring work,
maintenance and repairs, etc. of these products.
Sufcient care must be taken, as any violation of
the limitations may cause dangerous situations.
Be sure to read this manual before handling the
explosion protection type products.
WARNING
The terminal box cover and display cover are
locked by special screw. In the case of opening
the cover, use the hexagonal wrench (nominal
size 3).
The covers of explosion protection type products
are locked. Use this hexagonal wrench to open
and close the cover. Before opening the cover,
be sure to check that the power of owmeter has
been turned off. Once the cover is closed, be
sure to re-lock the product.
Be sure to lock the cover with the special screw
using the hexagonal wrench after tightening the
cover.
2.1 Technical Data
Applicable Standard:
FM 3600, FM3610, FM3615, FM3616, FM3810,
ANSI/UL UL 50E, NEMA 250, ANSI/UL 60079-0,
ANSI/UL 60079-7, ANSI/UL 60079-11, ANSI/UL
60079-18, ANSI/UL 61010-1, ANSI/UL 61010-2-30
Certicate:
FM 17US0140X
Integral Flowmeter
Explosionproof (Explosion Protection Code: FF2)
• Type of Protection:
CL I/II/III GP ABCDEFG
IS CL I GP ABCD
T6...T3
• Enclosure: Type 4X
• Ambient Temperature:
See Table 2.1 and Table 2.2.
• Process Temperature:
See Table 2.1 and Table 2.2.
• Power Supply:
100 to 240 Va.c. (50/60 Hz) / 100 to 120 Vd.c.
24 Va.c. (50/60 Hz) / 24 Vd.c.
• Um: 250 V
• Current I/O: 4 to 20 mA, 32 Vd.c. max.
• Digital I/O: 30 Vd.c. max., 200 mA max.
• Fieldbus I/O: 32 Vd.c. max., 15 mA max.
• Maximum Working Pressure:
Read “Fluid Temperature and Pressure”
Explosionproof with Output IS Circuit
(Explosion Protection Code: FJ2 and FT2)
• Type of Protection:
CL I/II/III GP ABCDEFG
IS CL I GP ABCD
AIS CL I/II/III GP ABCDEFG
T6...T3
• Enclosure: Type 4X
• Ambient Temperature:
See Table 2.1 and Table 2.2.
• Process Temperature:
See Table 2.1 and Table 2.2.
• Power Supply:
100 to 240 Va.c. (50/60 Hz) / 100 to 120 Vd.c.
24 Va.c. (50/60 Hz) / 24 Vd.c.
• Um: 250 V
• Control Drawing: DIE016-A92
• Maximum Working Pressure:
Read “Fluid Temperature and Pressure”
2. Explosion Protection Type

IM 01E21A03-01EN
4
<2. Explosion Protection Type> 4
Remote Sensor
Explosionproof
(Explosion Protection Code: FF2)
• Type of Protection:
CL I/II/III GP ABCDEFG
IS CL I GP ABCD
T6...T3
• Enclosure: Type 4X
• Ambient Temperature:
See Table 2.1 and Table 2.2.
• Process Temperature:
See Table 2.1 and Table 2.2.
• Um: 250 V
• Maximum Working Pressure:
Read “Fluid Temperature and Pressure”
Remote Transmitter
Explosionproof
(Explosion Protection Code: FF2)
• Type of Protection:
CL I/II/III GP ABCDEFG
• Enclosure: Type 4X
• Ambient Temperature: –40°C to +60°C
• Temperature class: T6
• Power Supply:
100 to 240 Va.c. (50/60 Hz) / 100 to 120 Vd.c.
24 Va.c. (50/60 Hz) / 24 Vd.c.
• Current I/O: 4 to 20 mA, 32 Vd.c. max.
• Digital I/O: 30 Vd.c. max., 200 mA max.
• Fieldbus I/O: 32 Vd.c. max., 15 mA max.
Explosionproof with Output IS Circuit
(Explosion Protection Code: FJ2 and FT2)
• Type of Protection
CL I/II/III GP ABCDEFG
AIS CL I/II/III GP ABCDEFG
• Enclosure: Type 4X
• Ambient Temperature: –40°C to +60°C
• Temperature class: T6
• Power Supply:
100 to 240 Va.c. (50/60 Hz) / 100 to 120 Vd.c.
24 Va.c. (50/60 Hz) / 24 Vd.c.
• Control Drawing: DIE016-A92
Table 2.1 Temperature Ratings
Model Size Process
Connection Lining
Temperature Table
Integral
Flowmeter
Remote
Sensor
AXG002, AXG005,
AXG010, AXG015
2.5 to 15 mm
(0.1 to 0.5 in.) Wafer, Flange PFA Lining Table A Table C
AXG025, AXG032,
AXG040, AXG050,
AXG065, AXG080,
AXG100, AXG125
25 to 125 mm
(1 to 5 in.) Wafer, Flange PFA Lining Table B
[Table J]*1
Table D
[Table J]*1
AXG150, AXG200,
AXG250, AXG300,
AXG350, AXG400
150 to 400 mm
(6 to 16 in.) Wafer, Flange PFA Lining Table A Table C
AXG015, AXG025,
AXG032, AXG040,
AXG050, AXG065,
AXG080, AXG100,
AXG125
15 to 125 mm
(0.5 to 5 in.)
Clamp, Union,
Butt Weld Joint PFA Lining Table E Table F
AXG002, AXG005,
AXG010, AXG015,
AXG025, AXG040,
AXG050, AXG080,
AXG100, AXG150,
AXG200
2.5 to 200 mm
(0.1 to 8 in.) Wafer Ceramics Tube Table G Table H
*1: When process connection code EA4 is specied, temperature table is changed to table in [ ].
The process connection code EA4 is available for AXG025, AXG040, AXG050, AXG080, and AXG100.

IM 01E21A03-01EN
5
<2. Explosion Protection Type> 5
Table 2.2 Ambient Temperature and Process Temperature
Table No. Ambient
Temperature
Temperature
Class
Maximum Surface
Temperature
Process
Temperature
A-40°C to +60°C
T6 T75°C -40°C to +75°C
T5 T90°C -40°C to +90°C
T4 T120°C -40°C to +120°C
T3 T130°C -40°C to +130°C
B
-40°C to +45°C T6 T75°C -40°C to +50°C
-40°C to +60°C
T5 T90°C -40°C to +75°C
T4 T120°C -40°C to +120°C
T3 T130°C -40°C to +130°C
C-40°C to +60°C
T6 T75°C -40°C to +75°C
T5 T90°C -40°C to +90°C
T4 T120°C -40°C to +120°C
T3 T150°C -40°C to +150°C
D
-40°C to +45°C T6 T75°C -40°C to +50°C
-40°C to +60°C
T5 T90°C -40°C to +75°C
T4 T120°C -40°C to +120°C
T3 T150°C -40°C to +150°C
E
-10°C to +45°C T6 T75°C -10°C to +50°C
-10°C to +60°C
T5 T90°C -10°C to +75°C
T4 T120°C -10°C to +120°C
T3 T130°C -10°C to +130°C
F
-10°C to +45°C T6 T75°C -10°C to +50°C
-10°C to +60°C
T5 T90°C -10°C to +75°C
T4 T120°C -10°C to +120°C
T3 T150°C -10°C to +150°C
G-10°C to +60°C
T6 T75°C -10°C to +75°C
T5 T90°C -10°C to +90°C
T4 T120°C -10°C to +120°C
T3 T130°C -10°C to +130°C
H-10°C to +60°C
T6 T75°C -10°C to +75°C
T5 T90°C -10°C to +90°C
T4 T120°C -10°C to +120°C
T3 T150°C -10°C to +150°C
J-10°C to +60°C
T6 T75°C -10°C to +75°C
T5 T90°C -10°C to +90°C
T4 T120°C -10°C to +100°C
T3 T150°C -10°C to +100°C

IM 01E21A03-01EN
6
<2. Explosion Protection Type> 6
Fluid Temperature and Pressure:
The gure shows the usable range of the sensor
in each specication. It is also limited by the
ange pressure rating of the process connection.
AXG###
PFA Lining, Remote Sensor (excluding high pressure
type (ASME Class 600 ange) and Hygienic Use)
Pressure
MPa (psi)
4 (580)
2 (290)
1 (145)
– 0.1 (–14.5) – 40
(–40)
40
(104)
100
(212)
150
(302)
Temperature °C (°F)
130
(266)
2.5 to 50 mm (0.1 to 2 in.) (flange type, wafer type)
65 to 200 mm (2.5 to 8 in.) (flange type, wafer type)
250 to 300 mm (10 to 12 in.) (flange type)
350 to 400 mm (14 to 16 in.) (flange type)
0
(32)
–10
(14)
F0201.ai
*1
PFA Lining, Integral Flowmeter (excluding high pres-
sure type (ASME Class 600 ange) and Hygienic Use)
Pressure
MPa (psi)
4 (580)
2 (290)
1 (145)
– 0.1 (–14.5)
– 40
(– 40)
40
(104)
100
(212)
Temperature °C (°F)
130
(266)
0
(32)
–10
(14)
2.5 to 50 mm (0.1 to 2 in.) (flange type, wafer type)
65 to 200 mm (2.5 to 8 in.) (flange type, wafer type)
250 to 300 mm (10 to 12 in.) (flange type)
350 to 400 mm (14 to 16 in.) (flange type)
F0202.ai
*1
*1: For wafer types of 150 to 200 mm (6 to 8 in.) or carbon
steel ange types (process connection code: C##) of 50 to
400 mm (2 to 16 in.), the minimum temperature is –10°C
(14°F).
PFA Lining, Remote Sensor and Integral Flowmeter
(high pressure type, ASME Class 600 ange)
F0203.ai
Pressure
MPa (psi)
Temperature °C (°F)
93.3
(200)
100
(212)
37.8
(100)
8.27 (1200)
8.15 (1182)
9.92 (1440)
50
(122)
0
(32)
-10
(14)
-0.1 (-14.5)
10 (1450)
PFA Lining, Hygienic Use (Remote Sensor and Integral
Flowmeter)
F0204.ai
Temperature °C (°F)
Pressure
MPa (psi)
1(145)
–0.1(–14.5)
15 to 125 mm (0.5 to 5 in.) (integral flowmeter)
150
(302)
130
(266)
15 to 125 mm (0.5 to 5 in.) (remote sensor)
0
(32)
–10
(14)
Ceramics Tube, Remote Sensor
Pressure
MPa (psi)
Temperature °C (°F)
2.5 to 50 mm (0.1 to 2 in.)
80 to 200 mm (3 to 8 in.)
4 (580)
2 (290)
–0.1 (–14.5) –10
(14)
0
(32)
100
(212)
150
(302)
F0205.ai
Ceramics Tube, Integral Flowmeter
Pressure
MPa (psi)
4 (580)
3.25 (471)
2 (290)
–0.1(–14.5)
2.5 to 50 mm (0.1 to 2 in.)
80 to 200 mm (3 to 8 in.)
–10
(14)
0
(32)
100
(212)
130
(266)
Temperature °C (°F)
F0206.ai

IM 01E21A03-01EN
7
<2. Explosion Protection Type> 7
2.2 Cable Entry
The type of cable entry is stamped near the cable
entry port according to the following codes.
Marking Screw Size
NASME 1/2 NPT Female
(1) Integral Flowmeter (2) Remote Sensor
F0207.ai
Marking
F0208.ai
Marking
(3) Remote Transmitter
F0209.ai
Marking
2.3 Installation
• All wiring shall comply with NFPA70 (US) and
local electric codes and requirements.
• Unused apertures shall be closed with suitable
certied blanking elements.
(The plug attached is certied.)
• The sensor is not surrounded by pipe insulation
material.
• In hazardous location, wiring shall be in conduit as
follows.
“SEAL ALL CONDUITS WITHIN 18 INCHES”
• In order to prevent the grounding conductor from
loosening, the conductor must be secured to the
terminal, tightening the screw with appropriate
torque. Care must be taken not to twist the conductor.
• Warning: In cases where the ambient temperature
exceeds 50°C, use external heat resistant wiring with
a maximum allowable temperature of 70°C or above.
• For IS Output type, refer to DIE016-A92 (Control
Drawin g)
The grounding terminals are located on the inside
and outside of the terminal area.
Connect the cable to the grounding terminal in
accordance with wiring procedure (a) or (b).
(a) Internal grounding terminal
(b) External grounding terminal
(1) Integral Flowmeter
(a)
(b)
F0210.ai
(2) Remote Sensor
(a)
(b)
F0211.ai
(3) Remote Transmitter
(b)
(a)
F0212.ai

IM 01E21A03-01EN
8
<2. Explosion Protection Type> 8
Read the Control Drawing.
All wiring shall comply with local installation requirements.
• Integral Type Flowmeter (Explosion Protection Code: FJ2)
F0213.ai