YOKOGAWA YFGW520 User manual

User’s
Manual YFGW520
Field Wireless Access Point
Read Me First
IM 01W02E02-11EN
IM 01W02E02-11EN
3rd Edition
This document species the important information to use this product correctly and
safely and the License Agreement of Attached Software for YFGW520 Field Wireless Ac-
cess Point.
Before use the product, be sure to read this document rst.
The conguration of the eld wireless system is described in User’s Manual of the
YFGW410 Field Wireless Management Station (IM 01W02D01-01EN). Read that document
rst.
Contents
Introduction...................................................................................................2
Safety Precautions .......................................................................................3
Explosion Protected Type Specications ...............................................11
Installation of an Explosion Protected Instrument ......................... 12
FM Approval (United States)............................................................... 14
FM Approval (Canada)......................................................................... 17
ATEX ...................................................................................................... 21
IECEx ..................................................................................................... 28
Ground Cable Connection .................................................................. 36
How to Use Online Manual ....................................................................... 37
Preparation to Use YFGW520 Attached Software ................................. 37
Copyright and Trademark Notices .......................................................... 38
Patent Notice ............................................................................................. 38
Open Source Software ............................................................................. 39
About User’s Manual ................................................................................ 39
Information of User’s Manual Revision .................................................. 40
Field Wireless Access Point Setup Tool
Software License Agreement................................................................... 41

2
<Read Me First>
IM 01W02E02-11EN
Introduction
This manual (IM 01W02E02-11EN) describes the safety precautions, explosion protected
type specications and the license agreement of attached software for the YFGW520.
There are three documents including this one for the YFGW520 listed below. Read them
along with this manual.
Document No. Document name Description
IM 01W02E02-01EN YFGW520
Field Wireless Access Point
This manual is stored in the attached DVD-ROM for
YFGW520. It describes installation, wiring, operation,
maintenance and specication of the YFGW520.
IM 01W02E02-11EN YFGW520
Field Wireless Access Point
Read Me First
This manual. It describes the safety precaution,
explosion protected type specications and the
license agreement of the attached software for the
YFGW520.
GS 01W02E02-01EN YFGW520
Field Wireless Access Point
Product specication including detailed model and
sufx code, optional specications and accessory of
the YFGW520.
nRegarding This User's Manual
lThis manual should be provided to the end user. Please recommend end users
to keep this manual at hand and refer to it as needed.
lThis manual and the identication tag attached on packing box are essential
parts of the product; keep them in a safe place for future reference.
lBefore use, read this manual thoroughly to comprehend its contents.
lThe purpose of the User’s Manual is to describe details of functions provided
in this product, not to warrant the product's suitability to the specic purposes
of customers.
lNo part of this manual may be reproduced in any form without Yokogawa's
written permission.
lThe contents of this manual may be changed without prior notice.
lAll reasonable effort has been made to ensure the accuracy of the contents of
this manual. However, if any errors or omissions are found, please inform any
of sales ofces listed on the back cover or your local distributor.
lThe specications covered by this manual are limited to those for the standard
type under the specied model number break-down and do not cover custom-
made instruments. When products whose sufx code or optional codes
contain code “Z” and an exclusive document is attached, please read it along
with this manual.
lPlease note that this User’s Manual may not be revised for any specication
changes, construction changes or operating part changes that are not
considered to affect function or performance.

3
<Read Me First>
IM 01W02E02-11EN
Safety Precautions
nSafety, Protection, and Modication of the Product
lIn order to protect the operator, product, and system controlled by the
product, observe the safety precautions described in this User’s Manual. If
users handle contrary to these instructions, we can not guarantee the safety.
lIf this instrument is used in a manner not specied in this User’s Manual, the
protection provided by this instrument may be impaired.
lModication of the product is strictly prohibited.
lIf customers attempt to repair or modify explosion protected type products
and fail to return them to their original state, the explosion protected structure
of this product will be lost, resulting in a hazardous state. All repairs and
modications of the product must be consulted with Yokogawa.
lIf any protection or safety circuit is required for the system controlled by the
product or for the product itself, prepares it separately.
lBe sure to use the spare parts approved by Yokogawa Electric Corporation
(hereafter simply referred to as Yokogawa) when replacing parts or
consumables.
lThe following symbols are used in the product and User’s Manual to indicate
that there are precautions for safety:
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate
injury or physical damage. It may also be used to alert against unsafe practices.
IMPORTANT
Indicates that operating the hardware or software in this manner may damage it or lead to system
failure.

4
<Read Me First>
IM 01W02E02-11EN
NOTE
Draws attention to information essential for understanding the operation and features.
TIP Indicates additional information.
SEE
ALSO
Indicates a source to refer to
Indicates a protective grounding terminal. Before using the product, ground the terminal.
Indicates a functional grounding terminal. Before using the product, ground the terminal.
Indicates a DC supply
nSafe Use of This Product
This product is designed to be used by a person with specialized knowledge. For the safety
of the operator and to protect the instrument and the system, please be sure to follow this
manual’s safety instructions when handling this instrument. If these instructions are not heeded,
the protection provided by this instrument may be impaired. In this case, Yokogawa cannot
guarantee that the instrument can be safely operated. Please pay special attention to the
following points:
(a) Installation
• This instrument may only be installed by an engineer or technician who has an expert
knowledge of this device. Operators are not allowed to carry out installation unless they meet
this condition.
• All installation shall comply with local installation requirements and the local electrical code.
(b) Wiring
• The instrument must be installed by an engineer or technician who has an expert knowledge
of this instrument. Operators are not permitted to carry out wiring unless they meet this
condition.
(c) Operation
• Wait 1 min. after the power is turned off, before opening the covers.
(d) Maintenance
• Please carry out only the maintenance procedures described in this manual. If you require
further assistance, please contact the nearest Yokogawa ofce.
• Care should be taken to prevent the build up of dust or other materials on the display glass
and the name plate. To clean these surfaces, use a soft, dry cloth.
(e) Explosion Protected Type Instrument
• Users of explosion protected instruments should refer rst to “Explosion Protected Type
Specications” section of this manual.
• The use of this instrument is restricted to those who have received appropriate training in the
device.

5
<Read Me First>
IM 01W02E02-11EN
• Take care not to create sparks when accessing the instrument or peripheral devices in a
hazardous location.
• Repair or modication to this instrument by customer will cause malfunction of explosion
protect function and hazardous situation. If you need to repair or modication, please contact
the nearest Yokogawa ofce.
(f) Modication
• Yokogawa will not be liable for malfunctions or damage resulting from any modicationmade
to this instrument by the customer.
(g) Product Disposal
• The instrument should be disposed of in accordance with local and national legislation/
regulations.
nWarranty
lThe warranty terms of this instrument are described in the quotation. We will
make any repairs that may become necessary during the guaranteed term free
of charge.
lPlease contact our sales ofce or your local distributor if this instrument
requires repair.
lIf the instrument is faulty, contact us with complete details about the
problem and the length of time it has been faulty, and state the model and
serial number. We would appreciate the inclusion of drawings or additional
information.
lThe results of our examination will determine whether the product will be
repaired free of charge or on an at-cost basis.
nThe guarantee will not apply in the following cases:
lDamage due to negligence or insufcient maintenance on the part of the
customer.
lProblems or damage resulting from handling, operation or storage that
violates the intended use and specications.
lProblems that result from using or performing maintenance on the instrument
in a location that does not comply with the installation location specied by
Yokogawa.
lProblems or damage resulting from repairs or modications not performed by
Yokogawa or someone authorized by Yokogawa.
lProblems or damage resulting from inappropriate installation after delivery.

6
<Read Me First>
IM 01W02E02-11EN
l Problems or damage resulting from disasters such as res, earthquakes,
storms, oods, or lightning strikes and external causes.
n Warranty and Disclaimer
l Yokogawa assumes no responsibilities for this product except as stated in the
warranty.
l Yokogawa shall have neither liability nor responsibility to any person or
entity with respect to any direct or indirect loss or damage arising from using
the product or any defect of the product that Yokogawa can not predict in
advance.
n Authorized Representative in the EEA
The Authorized Representative for this product in the EEA is: Yokogawa Europe B.V.
Euroweg 2, 3825 HD Amersfoort, THE NETHERLANDS.
n Notes on Hardware
lAppearance and Accessories
Check the following when you receive the product:
• Appearance
• Standard accessories
Contact our sales representative or your local distributor if the product’s coating has come off or
any accessories are missing.
l Model and Sufx Codes
The name plate on the product contains the model and sufx codes. Verify that the specication
indicated in the “MODEL AND SUFFIX CODES” and “OPTIONAL SPECIFICATIONS” in General
Specications “GS 01W02E02-01EN” is in compliance with the specications written on the order
sheet. If you have any questions, contact our sales ofce or your local distributor.
n Notes on Attached Software
l Before opening the media package, read YFGW520 Software License
Agreement. Once the package is opened, it is thought that the contract is
agreed.
l Yokogawa assumes no responsibilities for this software except as stated in
the warranty.
l This software is used with this product exclusively. This can be installed in the
computer which connects with this product.

7
<Read Me First>
IM 01W02E02-11EN
n Regulatory Compliance for Radio and Telecommunication
Please conrm that an installation region fullls a standards, require additional regulatory
information and approvals, contact to Yokogawa Electric Corporation.
l Radio Equipment Directive
Hereby, Yokogawa Electric Corporation declares that the radio equipment type YFGW520 is
in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at the following internet address:
http://www.yokogawa.com/d/
l EMC Conformity Standards
EN 301 489-1, EN 301 489-17, EN 61326-1, EN 55011 Class A, Group 1, EN 61000-6-2
CAUTION
This equipment is a Class A product.
This equipment is not intended for use in residential environments and may not provide adequate
protection to radio reception in such environments.
Please use this equipment in the industrial environment only.
l Safety Conformity Standards
Applicable standard: EN 61010-1, EN 62479, EN 60825-1
(1) Pollution Degree 2
“Pollution degree” describes the degree to which a solid, liquid, or gas which deteriorates
dielectric strength or surface resistivity is adhering. “2” applies to normal indoor atmosphere.
Normally, only non-conductive pollution occurs. Occasionally, however, temporary conductivity
caused by condensation must be expected.
(2) Installation Category I
“Overvoltage category (Installation category)” describes a number which denes a transient
overvoltage condition. It implies the regulation for impulse withstand voltage. “I” applies to
electrical equipment which is supplied from the circuit when appropriate transient overvoltage
control means (interface) are provided.
(3) Laser Safety
100BASE-FX (Single mode Fiber) model of YFGW520 is compliant with IEC 825-1 Class 1 and
CDRH 21-CFR 1040 Class 1 eye safety requirements.
CAUTION
• To avoid eye injury although, please do not see a light source.
CAUTION
• When the maximum operating temperature is more than 60°C, use the wiring cable of 80°C
or higher temperature rating.

8
<Read Me First>
IM 01W02E02-11EN
l Spectrum Conformity Standard
EN 300 328
lFCC compliance
FCC ID: SGJ-WFC015
FCC Approval (Part 15C)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two con-
ditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Co-located:
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
FCC WARNING
Changes or modications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio commu-
nications. Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
RF Exposure Compliance:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environ-
ment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be
installed and operated keeping the radiator at least 20 cm or more away from person’s body.

9
<Read Me First>
IM 01W02E02-11EN
l ISED compliance
IC: 8999A-WIC014
This device complies with ISED’s applicable licence-exempt RSS standard(s). Operation is sub-
ject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the
device.
This radio transmitter 8999A-WIC014 has been approved by ISED to operate with the antenna
types listed below with the maximum permissible gain and required antenna impedance for each
antenna type indicated. Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with this device.
Antenna type Gain
Sleeve 2.14 dBi
Collinear 9 dBi
Hybrid patch 15 dBi
French:
Le présent appareil est conforme aux CNR d’ISDE applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Le présent émetteur radio 8999A-WIC014 a été approuvé par Industrie Canada pour fonctionner
avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal.
Les types d’antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal
indiqué, sont strictement interdits pour l’exploitation de l’émetteur.
Type d’antenne Gain
Sleeve 2.14 dBi
Collinear 9 dBi
Hybrid patch 15 dBi
RF Exposure Compliance:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environ-
ment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should
be installed and operated keeping the radiator at least 20 cm or more away from person’s body.
French:
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un envi-
ronnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF)
CNR-102 de l’IC. Cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou
plus entre le radiateur et le corps humain.
lRRA compliance
This product complies with the Radio Waves Act (Republic of Korea).
Registration No: R-R-YHQ-WRA011, R-C-YHQ-WRA013
Equipment Name: Field Wireless Access Point
Model name: YFGW520
Trade Name: Yokogawa Electric Corp.
Manufacturer: Yokogawa Electric Corp.
Country of Origin: Japan

10
<Read Me First>
IM 01W02E02-11EN
nControl of Pollution Caused by the Product
lEU RoHS
This product is in conformity with the following standard:
EN 50581:2012 (Technical documentation for the assessment of electrical and electronic
products with respect to the restriction of hazardous substances)
lChina RoHS
This is an explanation for the product based on “Control of Pollution caused by Electronic
Information Products” in the People’s Republic of China.
電子情報製品汚染制御管理弁法（中国版 RoHS）
产品中有害物质或元素的名称及含量
型号 部件名称
有害物质
铅
（Pb） 汞 （Hg） 镉 （Cd） 六价铬 （Cr(VI)） 多溴联苯 （PBB） 多溴二苯醚 （PBDE）
YFGW520
现场无线接入点
壳体 × ○ ○ ○ ○ ○
基板组件 × ○ ○ ○ ○ ○
电源连接线 × ○ ○ ○ ○ ○
天线组件 × ○ ○ ○ ○ ○
○ ：表示该部件的所有均质材料中的有害物质的含量均在GB/T26572 标准中所规定的限量以下。
× ：表示至少该部件的某些均质材料中的有害物质的含量均在GB/T26572 标准中所规定的限量以上。
环保使用期限：
该标识适用于SJ /T11364 中所述，在中华人民共和国销售的电子电气产品的环保使用期限。
注）该年数为“环保使用期限”，并非产品的质量保证期。