YOODA SMART CONTROL UNIT User manual

1. Safety rules
YOODA SMART CONTROL UNIT
In order to fully explore available functions of YOODA SMART CONTROL UNIT (YSC_UNIT) please take a moment and read this manual before using
the device.
All devices work on 433 MHz frequency.
Table of contents
www.sukcesgroup.pl
1. Safety rules
2. YSC unit description
2.1 Technical information
2.2 Construction
2.3 Working mode
3. First start-up
3.1. Initialisation
3.2. Downloading
app and changing language
3.3. Connecting to Wi-Fi
3.4. Connecting by Ethernet cable
4. Mobile app - interface description
5. Configuration and work mode
5.1. Adding devices
5.2. Controlling devices
5.3. Crating groups
5.4. Creating scenarios
5.5. Connecting YSC unit to local Wi-Fi
5.6. Remote access service
5.7. Setting password
6. Controlling device from computer
7. Demo version
1. Before connecting or starting control unit please read this manual.
2. Device needs to be connected to the internet according to specific parameters.
3. Control unit should not operate in places with high humidity (bathroom, sauna etc.).
4. Control unit should not be places next to sources of high temperature (radiator, fireplace, furnace etc.).
5. Control unit should not be placed within the reach of children.
6. Control unit should not be covered. It’s recommended to leave at least 10 cm of free space over and on the sides of the
device.
7. Before cleaning or conservation control unit should be disconnected from power source. Unit is not water resistant
and should be protected from any liquids or any other potentially harmful substances.
8. Unit should not be opened. Do not attempt to repair the unit yourself - only manufacturer or authorized retailer can
perform any modifications or repairs.
9. Control unit should not be placed next to a strong magnetic field, as it can cause permanent damage to the device.
10. Control unit cannot be operated in explosive areas or where it is legally prohibited.
11. To protect the unit during a thunder storm power supply should be disconnected.
12. Control unit should not be connected to power supply that do not met all technical requirements.
13. Control unit should be protected from vibrations and shakes.
14. Control unit needs to be protected with a password - see point 2.3.
This symbol found on the apparatus indicates that the apparatus must be placed in a separate collection facility for
electronic waste and not disposed with household waste. Instead, it should be handed over to an applicable collection
point for the recycling of electrical and electronic equipment.
Allowing for specialized collection point to handle used device will allow for raw materials to be recycled and will have
positive impact on the natural environment.

2. YSC unit description
2.1 Technical information
www.sukcesgroup.pl
1. Can control YOODA and CORTINO brand devices with smartphones, tablets and computers.
2. Allows to create and manage groups of devices.
3. Allows to create scenarios (combination of set actions to different devices) and determine the time of automatic
activation.
4. Can generate own Wi-Fi network or work in local Wi-Fi network (wireless or by Ethernet connection).
5. Control unit can be set and controlled by dedicated app available for Android and iOS.
6. Encrypted network connection.
1. Interface:
Wi-Fi, Ethernet, ISM 433 MHz
2. Memory:
up to 255 devices
3. Power consumption:
1.6 W
4. Setting memory:
CR1220 battery
230 V / 50 Hz 200 m 35 m 433,92 MHz
L1
Outdoor L2 Indoor Operating frequency
20
Roller shutter with remotely controlled motor
L2L1
At the bottom of the control unit you will find rating label with detailed information:
a) control units serial number S/N,
b) MAC address of Ethernet and Wi-Fi interface,
c) CE labelling,
d) power supply.
YSC_UNIT
S/N: YO-020017
MADE IN POLAND
DC IN: 5 V 2 A
MAC ETH/WIFI: AC-A2-13-B7-FC-96
YOODA SMART CONTROL UNIT
In order to fully explore available functions of YOODA SMART CONTROL UNIT (YSC_UNIT) please take a moment and read this manual before using
the device.
All devices work on 433 MHz frequency.
5. Protection degree:
IP 20
6. Dimensions:
110 x 80 x 27 mm
7. Power supply:
Input: 230 V / 50 Hz
Output: 12 V DC lub 5 V DC
according to label on the control unit
Warning! Voltage and current should correspond with parameters declared by the manufacturer. Not complying with this
regulations may result in damaging the control unit.
Radio signal range is a variable value and can differ from declared values depending on conditions in which device
operates. Possible sources of changes in range are building construction, interference caused by other radio transmitters etc.

YOODA SMART CONTROL unit can work in one of the three modes.
Work mode can be changed after creating first connection of control unit through app:
Settings > Network connections > Wireless network connection
Warning! Control unit in default settings does not require password for connection, which allows for unauthorised
users to set connection and control programmed devices. For safety reasons we recommend setting control units
password (see section 5.7 of this instruction). Please remember, that control unit password is independent from Wi-Fi
network password and has to be set individually - these are two different passwords.
2. YSC unit description
2.2. Construction
2. YSC unit description
2.3 Working mode
www.sukcesgroup.pl
power supply
radio
LAN
Wi-Fi
LED diodes (front):
1. Power supply
- light up diode informs if the control unit is connected to power
source.
2. Radio
- diode lights up whenever radio is activated.
3. LAN
- diode lights up when control unit is connected by Ethernet
interface.
4. Wi-Fi
- diode inform on work status of Wi-Fi interface.
Panel (back):
1. Power supply input
- entry for power supply cable.
2. Reset button
- pressing RESET button will result in deleting all Wi-Fi setting of
the control unit; pressing and holding for 5 seconds will result in
restoring factory settings.
3. Gniazdo Ethernet
- allows to connect the control unit to LAN network or router by
using Ethernet cable.
4. Antena
- antenna should be bolted to the antenna connection; antenna
works in 433MHz operating frequency.
1
2
4
3
1. Control unit generates own Wi-Fi network
- This is the default mode, that activates
after first startup.
- Allows to control programmed devices
without the necessity to connect to other
Wi-Fi network or to router.
- Control unit generates own Wi-Fi network
named ‘SmartControl-UnitsSerialNumber’
– instruction of connection can be found
in section 3.3.
- Generated Wi-Fi network is unprotected.
Encryption method, name of the network
and password can be changed in the app:
Settings > Network connections >
Wireless network connection.
- In this mode distant remote control is
possible if control unit is connected by
Ethernet cable to the internet source
(directly or by router).
2. Control unit uses existing Wi-Fi
network
- Easiest way is to connect control unit
to working router using Ethernet cable.
- To connect app on mobile device with
control unit can be done by logging into
local Wi-Fi network - see section 3.4.
- Other way includes connecting to
control units Wi-Fi network - see
previous paragraph.
- Network generated by control unit
can be switched off.
- This work mode allows distant
remote control – see section 5.6.
3. Control unit connects remotely to local
Wi-Fi network
- This mode allows for control unit to be
placed in the middle of the building so
that optimal radio signal range can be
achieved.
- Mode requires to set remote connection
parameters of the control unit with local
Wi-Fi network (see section 5.5).
- Network generated by control unit
can be switched off.
- This work mode allows distant
remote control – see section 5.6.
YOODA SMART CONTROL UNIT
In order to fully explore available functions of YOODA SMART CONTROL UNIT (YSC_UNIT) please take a moment and read this manual before using
the device.
All devices work on 433 MHz frequency.

3. First start-up
3.1 Initialisation
3. First start-up
3.2 Downloading app and changing language
3. First start-up
3.3 Connecting to Wi-Fi
www.sukcesgroup.pl
power supply
radio
power supply Wi-Fi
1. After unpacking the control unit mount the antenna and
connect the unit to power source. ‘Power supply’ diode should
light up steady as long as the energy supply is uninterrupted.
‘Radio’ diode will be flashing until device initialization is finished.
2. After about 60 seconds, when ‘Radio’ diode stops flashing,
control unit is ready for work.
To operate control unit properly dedicated app needs to be downloaded and installed on the device. Using Google
Play or App Store search ‘yooda smart control’ phrase or use QR code below.
Language of the app can be changed. When app is started for the first time it will automatically set to the language
of the device (or English, if it’s unavailable). To change the language (in regular mode or in DEMO mode) go into
‘Setting’ and then ‘Language’.
After connecting control
unit and finished initialization
it will automatically generate
own Wi-Fi network named
‘SmartControl_SerialNumber’.
After running the app,
network configuration
screen will appear. Press
‘Find Smart Control Unit’
for automatic IP address
setting.
After finding control unit
choose ‘Connect’.
Settings
Data usage
More...
Sound
Display
Storage
Power management
SCAN
DEVICE
Apps
Users
Location
Security
PERSONAL
WIRELESS & NETWORKS
ADD NETWORK
On
Yooda SmartControl
Connect remotely
Yooda SmartControl
Find Smart Control Unit
Connect remotely
192 168 1 1
Find Smart Control Unit
Connect
Android iOS
YOODA SMART CONTROL UNIT
In order to fully explore available functions of YOODA SMART CONTROL UNIT (YSC_UNIT) please take a moment and read this manual before using
the device.
All devices work on 433 MHz frequency.
Using mobile device
(smartphone, tablet etc.)
search and connect to
unprotected SmartControl
network.
YOODASC
Out of range
SmartControl-YO-010001
Connected

3. First start-up
3.4 Connecting by Ethernet cable
4. Mobile app - interface description
www.sukcesgroup.pl
Included Ethernet cable should be plugged into back panel of the control unit and to free output slot in working
router.
After connecting control
unit to router by Ethernet
cable run app and select
“Find SmartControl Unit”.
Than choose Wi-Fi network
generated by the router (not
by the Smart Control unit).
After successfully connecting
to the network, control unit
is ready to work.
Yooda SmartControl
Connect remotely
Yooda SmartControl
Find Smart Control Unit
Connect remotely
192 168 1 1
Find Smart Control Unit
Connect
YOODA SMART CONTROL UNIT
In order to fully explore available functions of YOODA SMART CONTROL UNIT (YSC_UNIT) please take a moment and read this manual before using
the device.
All devices work on 433 MHz frequency.
Status bar informs us on
work mode.
LAN - control unit works in
local network,
NET - remote access service,
connection to internet,
DEMO - app is in demo mode,
Yooda SmartControl
All
Cinema room
17
8
Living room 11
My home My scenarios Settings YOODA shop
App has 4 main tabs:
My home - controlling devices
and group of devices,
My scenarios - adding,
configuration and turning
on/off created time scenarios,
Setting - adding and editing
devices, adding and editing
groups of devices, changing
control unit settings (work
mode, connection settings,
password) and changing
language,
Yooda SmartControl
All
Cinema room
17
LAN
8
Living room 11
My home My scenarios Settings YOODA shop
LAN
YOODA shop - redirects to
www.sukcesgroup.pl web
page.
To change the tab simply
slide screen horizontally or
press the tab.
OK - instructions were
performed successfully,
WORK - app waits for
confirmation.

5. Configuration and work mode
5.1 Adding devices
www.sukcesgroup.pl
Information on how to add radio receiver can be found in instruction of that device.
Recently performed action is marked in the app.
As radio receivers can be controlled with different devices with app, recently performed action may not represent the state
of the radio receiver status.
Widgets can be created for app installed on Android system.
Widgets allow for different devices to be controlled even more easily without the need to run the app. It can be switched
between local network and remote access service, the size of the widget can be changed. It is functional and makes it
easier for different devices even faster - e.g. when driving into the garage less focus is needed to control the app.
5. Configuration and work mode
5.2 Controlling devices
In the ‘Settings’ tab press ‘Devices’. Tap ‘Add device’. Choose type of the device and
specify its name, than press ‘Next’.
Using programming button ‘Prog’ and
controlling buttons add device using
instruction of the radio receiver.
Yooda SmartControl
Devices groups
LAN
Network connections
Date, time
Advanced
My home My scenarios Settings YOODA shop
Yooda SmartControl
Roller blind
Projection screen
Curtain 1
Curtain 2
Light
Socket
Gate
Close
Yooda SmartControl
Device
Cancel
The name of the device must be unique, other
device cannot share the same name.
Impulse mode
deactivated
Yooda SmartControl
Device
OK
Impulse mode
Device control
deactivated
Device type
Device name
Outside shutter
Bedroom
Devices
Add device
Prog
Device type
Device name
Outside shutter
CancelNext
Controlling of the devices can be
performed by using controlling
buttons. There are 4 types of
control depending on the device.
1. Standard control
Control is performed via three
buttons – ‘UP’, ‘STOP’, ‘DOWN’.
This mode is best to control roller
shutters or roller blinds, horizontal
blinds, projection screen, roller gate
etc.
2. Horizontal control
Control is performed via three
buttons – ‘OPEN’, ‘STOP’, ‘CLOSE’.
(e.g. curtains, awnings or pergolas).
Yooda SmartControl
Device
Device control
deactivated
Device type
Device name
Outside shutter
Bedroom
Prog
impulse mode
OK Cancel
3. On / off control
Device is controlled by two witches
- on and off, e.g. lighting, power
socket.
4. Step-by-step control
Device is controlled with a single
switch, e.g. sectional garage door,
up and over garage door,
double-leaf garage door, sliding
gate, garden watering system.
YOODA SMART CONTROL UNIT
In order to fully explore available functions of YOODA SMART CONTROL UNIT (YSC_UNIT) please take a moment and read this manual before using
the device.
All devices work on 433 MHz frequency.
5. Impulse control
Some devices, such as roller blind
and horizontal blind, can be
controlled using impulse mode.
Before choosing this type of
control device needs to be set to
impulse as it is described in its
instruction. Activating impulse
mode changes control buttons.
Control buttons will be sending
amount of impulses equal to the
length of uninterrupted time of button
being pushed. Motor works as long
as the button is being pushed.
Pushing button longer than for
2 seconds will result in moving
the shade to its limit position.

5. Configuration and work mode
5.3 Crating groups
5. Configuration and work mode
5.4 Creating scenarios
www.sukcesgroup.pl
In the ‘Settings’ tab press ‘Devices
groups’.
Specify name of the group, select preferred
image and add devices into the group.
Select ‘Save’ to save the settings
after configuration.
Press ‘Add devices group’.
Yooda SmartControl
LAN
Network connections
Date, time
Advanced
My home My scenarios Settings YOODA shop
Devices
Devices groups
Yooda SmartControl
Cinema room
11 devices
Living room
15 devices
Zamknij
Add devices group
Yooda SmartControl
Devices group
Devices
Bedroom
Devices group name
Devices group’s image
Anuluj Save
By creating scenario user selects different devices already added to the app and chooses its action when scenario is
beeing run (e.g. roller shutter - close, TV - turn on, lights - turn off, etc.).
Scenario can be activated at any time manually or it can be started automatically, cyclically at a specific time, if it was
determined and switched to active. For scenario to work correctly, accurate date and time has to be set for the control
unit. Date can be set by choosing ‘Date, time’ in the ‘Settings’ tab.
To add new action click ‘Add
scenario’ in the ‘My scenarios’ tab.
Enter name of the scenario. Activate scenario, then specify the
time of when the event should work.
Yooda SmartControl
LAN
Exit
My home My scenarios Settings YOODA shop
Movie
Inactive
Inactive
Inactive
End of movie
Add scenario
Yooda SmartControl
Devices
Night
Scenario name:
Active
Cancel Save
Scenario settings
Yooda SmartControl
Devices
Night
Scenario name:
Cancel Save
Scenario settings
Scenario activation time:
Active
Add devices for the scenario. After choosing devices specify its
actions and save scenario by
clicking ‘Save’.
After creating new scenario it can be
activated manually by clicking on the
‘Play’ button placed next to the name
of the time event.
Yooda SmartControl
Devices
Night
Scenario name:
Cancel Save
Scenario settings
Scenario activation time:
Active
Yooda SmartControl
Devices
Night
Scenario name:
Cancel
Scenario settings
Scenario activation time:
Monday, Tuesday, Wednesday, Thursday, Friday 20:00:00
Outside hutter 2
Outside shutter 1
Inside shutter
Lobby
Light 1
Active
Save
Close
Close
Open
Close
Off
Yooda SmartControl
LAN
Exit
My home My scenario Settings YOODA shop
Movie
Inactive
Inactive
Inactive
End of movie
Add scenario
Night
Monday, Tuesday, Wednesday, Thursday, Friday 20:00:00
YOODA SMART CONTROL UNIT
In order to fully explore available functions of YOODA SMART CONTROL UNIT (YSC_UNIT) please take a moment and read this manual before using
the device.
All devices work on 433 MHz frequency.

After running control unit for the first time, in its default mode, it generates own Wi-Fi network that we can log into. After
that there’s a possibility to connect unit to other, already existing, Wi-Fi network. For returning the control unit to default
mode press ‘Reset’ button on the back panel of the control unit.
5. Configuration and work mode
5.5 Connecting YSC unit to local Wi-Fi
www.sukcesgroup.pl
Using ‘Settings’ tab choose ‘Network
connections’.
Choose ‘Wireless network
configuration’.
Change network mode to ‘Connect
to home Wi-Fi network’.
Yooda SmartControl
LAN
Date, time
Advanced
My scenario Moje scenariusze Settings YOODA shop
Devices
Devices groups
Network connections
Yooda SmartControl
Received automatically from net (DHCP)
Cable network settings
Close
Provide own Wi-Fi network
Network name
Channel
Encryption
SmartControl
Network is not encrypted
Received automatically from net (DHCP)
Wireless network configuration (WLAN)
7
Yooda SmartControl
Kanał
SmartControl
None
Network name
Network encryption mode
Cancel OK
Network connections
7
Provide own WiFi network
Network mode
Yooda SmartControl
Kanał
SmartControl
Brak
Network name
Metoda szyfrowania sieci
Cancel OK
1
Provide own WiFi network
Network mode
In Android system choose network
using ‘Choose Wi-Fi network’
button. In iOS enter name of
the network.
Choose network encryption mode,
enter password and press ‘OK’.
Message informing about disconnection
from current Wi-Fi network will be shown.
Log in to local Wi-Fi network by choosing
‘Wi-Fi’ and pressing ‘Continue’.
Yooda SmartControl
Choose Wi-Fi network
Connection between mobile device and Smart Control unit is lost.
Please log your device to the same network as the unit.
Continue
Yooda SmartControl
None
Network name
Network encryption mode
Use data from router (DHCP)
Configure manually
Cancel Save
Connect to home Wi-Fi network
SmartControl
Network mode
Choose Wi-Fi network
Yooda SmartControl
Use data from router (DHCP)
Configure manually
Cancel
Network name
Choose Wi-Fi network
|
Show password
Network access password
YOODASC
WPA2-PSK
Network encryption mode
Save
After logging in press ‘Find Smart
Control unit’.
Message will be shown after
finding Smart Control unit.
New IP address of Smart Control
unit will be shown. Press ‘Connect’.
Yooda SmartControl
Connect remotely
192 168 1 1
Connect
Find Smart Control Unit
Yooda SmartControl
Connect remotely
192 168 1 1
Connect
Find Smart Control Unit
Yooda SmartControl
Connect remotely
192 168 1 1
Połącz
Find Smart Control Unit
Finding Smart Control Unit
Smart Control Unit was found
OK
Network connections Network connections
Turned off
Provide own Wi-Fi network
Connect to home Wi-Fi network
Wireless network configuration (WLAN) Wireless network configuration (WLAN)
YOODA SMART CONTROL UNIT
In order to fully explore available functions of YOODA SMART CONTROL UNIT (YSC_UNIT) please take a moment and read this manual before using
the device.
All devices work on 433 MHz frequency.

Remote access service should be activated when automated devices are to be controlled outside from the local Wi-Fi
network. Reaction time of automated devices controlled using remote access, considering usage of staging servers, is
longer than when using local Wi-Fi network.
For remote access to work properly:
1. Smart Control unit needs to be connected to the internet.
2. Current time needs to be set on Smart Control unit.
3. Remote access service function needs to be activated.
To activate remote access service
choose ‘Advanced’ in ‘Settings’ tab.
Run ‘Remote access service’ option. Choose ‘Turned on’ option to activate
remote access function.
After entering ‘Remote access
service’ again test activated function.
When controlling device is out of reach
of local Wi-Fi network control unit search
screen will be displayed. To connect
control device to Smart Control unit
press ’Connect remotely’.
When controlling device is again
within reach of local Wi-Fi network it
can be reconnected, by turning it off
using ‘Settings’ tab.
Yooda SmartControl
LAN
Date, time
My home My scenario Settings YOODA shop
Devices
Devices groups
Network connections
Advanced
Yooda SmartControl
LAN
My home My scenario Settings YOODA shop
Yooda SmartControl
Close
Change Smart Control Unit access password
Advanced settings
Smart Control Unit IP address
Connection to Smart Control Unit
192.168.1.1
Software version
current
newest
Mobile app version
1.0,3/1.0.3
1.0,3/1.0.3
1.2.3
About YOODA Smart Control Unit
Remote access service state turned off
Remote access service
Yooda SmartControl
Close
Service allows connection with Smart Control Unit through Internet. To make it work the unit
must have Internet access, e.g. by the home network.
Remote access service
Turned off
Yooda SmartControl
Cancel
Service allows connection with Smart Control Unit through Internet. To make it work the unit
must have Internet access, e.g. by the home network.
Remote access service requires correct time set on Smart Control Unit.
Remote access service state
Application is using remote access mode. Smart Control unit configuration is not permitted in this
mode. Comunication is slower than in local mode as well.
Please use button below to quit remote access mode.
Remote access service
Turned off
Test remote access service
Yooda SmartControl
192 168 1 1
Connect
Find Smart Control Unit
Smart Control Unit IP Adress
Connect remotely Quit remote access mode
5. Configuration and work mode
5.6 Remote access service
www.sukcesgroup.pl
Remote access service
Advanced settings
YOODA SMART CONTROL UNIT
In order to fully explore available functions of YOODA SMART CONTROL UNIT (YSC_UNIT) please take a moment and read this manual before using
the device.
All devices work on 433 MHz frequency.

To set password go into ‘Settings’,
and then choose ‘Advanced’.
Choose ‘Change Smart Control unit
access password’.
Enter current password and new
password and accept it by pressing
‘OK’.
Yooda SmartControl
LAN
Date, time
My home My scenario Settings YOODA shop
Devices
Devices groups
Network settings
Advanced
Yooda SmartControl
Close
Smart Control Unit IP address
Connection to Smart Control Unit
192.168.1.1
Software version
current
newest
Mobile app version
1.0,2/1.0.1
1.0,2/1.0.1
0.1.0
About YOODA Smart Control Unit
Remote access service state turned off
Remote access service
Yooda SmartControl
Close
Smart Control Unit IP address
Connection to Smart Control Unit
192.168.1.1
Software version
current
newest
1.0,2/1.0.1
1.0,2/1.0.1
0.1.0
About YOODA Smart Control Unit
Remote access service state turned off
Remote access service
Change Smart Control Unit access password
5. Configuration and work mode
5.7 Setting password
6. Controlling device form computer
www.sukcesgroup.pl
Control unit, as well as the computer, must be connected to the same local Wi-Fi network.
To control roller shutters using computers web browser it’s necessary to know IP address of the control unit in local Wi-Fi
network. We can check it in the mobile app.
In ‘Settings’ tab choose ‘Advanced’. Check control units IP address.
Yooda SmartControl
LAN
Date, time
My home My scenario Settings YOODA shop
Devices
Devices groups
Network connections
Advanced
Yooda SmartControl
Close
Software version
current
newest
Mobile app version
1.0,3/1.0.3
1.0,3/1.0.3
1.2.3
About YOODA Smart Control Unit
Remote access service state turned off
Remote access service
Change Smart Control Unit access password
Smart Control Unit IP address
Connection to Smart Control Unit
192.168.1.1
Advanced settings
Advanced settings
Zaawansowane ustawienia
Change Smart Control Unit access password
Mobile app version
Change Smart Control Unit access password
Old password (empty-no password)
New password (empty-no password)
Repeat new password
OK Cancel
YOODA SMART CONTROL UNIT
In order to fully explore available functions of YOODA SMART CONTROL UNIT (YSC_UNIT) please take a moment and read this manual before using
the device.
All devices work on 433 MHz frequency.

7. Demo version
www.sukcesgroup.pl
Enter IP into address bar of browser of computer connected to the same local Wi-Fi network as the control unit.
Szukaj
Devices
Click group to control individual devices.
PL / ENG Log out
All
Living room
Cinema room
Devices
Devices
Devices
192.168.1.1/index.php
After choosing group of devices control buttons will be displayed. By using ‘PL|ENG’ buttons language version can be
changed.
Szukaj
Devices
Click group to control individual devices.
Log out
All
Living room
Cinema room
Devices
Devices
Outside shutter 1
Devices
Outside shutter 2
PL / ENG
To run DEMO version choose ‘Demo
version’.
Exemplary programmed control unit
with prepared app is being presented.
Whenever using DEMO version its
name is being shown in top right
of the app.
To end DEMO version choose ‘Close
demo’ in ‘Setting’ tab.
Yooda SmartControl
All
Ground floor
17
8
Garage
First floor
Garden
11
8
2
My home My scenario Settings YOODA shop
Yooda SmartControl
Devices groups
LAN
Network connections
Date, time
Advanced
My home My scenario Settings YOODA shop
Demo version was designed to show all the possibilities of the YOODA SMART CONTROL app.
For the app to work in DEMO mode there is no need to connect to any control unit. App is equipped with exemplary setting.
Yooda SmartControl
0 0 0 0
Connect
Find Smart Control Unit
Demo version
DEMO
Close demo
YOODA SMART CONTROL UNIT
In order to fully explore available functions of YOODA SMART CONTROL UNIT (YSC_UNIT) please take a moment and read this manual before using
the device.
All devices work on 433 MHz frequency.