YOODA MAGNETIC Series Configuration guide

In order to fully explore available functions of MAGNETIC series please take a moment and read this manual before using the device. MAGNETIC transmitters
are compatible with all YOODA brand devices.
Illustrations (from the top):
Fig. 1. Single-channel CAMELEO control unit, white, front
Fig. 2. Single-channel CAMELEO control unit, white, back
General information
Detailed description
1. Control:
can control single motor
2. Memory:
up to 20 transmitters
3. Range:
200 meters outdoor,
35 meters indoor
4. Power supply:
230 V / 50 Hz
5. Output voltage:
230 V / 50 Hz
6. Output power:
300 W
7. Dimensions:
80 x 80 x 43 mm
8. Operating temperature:
frim 0°C to 50°C
9. Protection degree:
IP 30
10. Time of settings being saved
in case of power shortage:
up to 4 hours
Radio receiver range is a variable value and can differ from declared values depending on conditions in which device
operates. Possible sources of changes in range are building construction, interference caused by other radio transmitters
etc.
MAGNETIC_1CfT
www.sukcesgroup.pl
UP button
STOP button
DOWN button
L1 TIMER
PROGRAMMING button
P1 CONFIGURATION
CHANGE button
WORK MODE button
day of the week
minute
hour
current work mode
roller shutter
direction
lack of power
supply information

In order to fully explore available functions of MAGNETIC series please take a moment and read this manual before using the device. MAGNETIC transmitters
are compatible with all YOODA brand devices.
Connection
Changing work mode
Installation of the tubular motor should be performed by specialists with 1kV or higher SEP-certified electrician's
licence (SEP - Association of Polish Electrical Engineers) or equal license. Device is designed to operate in places
shielded from unfavourable weather conditions. Motor should be installed in accordance with all provisions of region-
al law and professional standards. All cables connecting power receiver with electric source should be protected from
overload and short-circuits effects with devices automatically disconnecting power. Device should be powered with
a separate source and protected only with a fast-blow fuse (never slow-blow fuse). Creating electrical system using
inadequate fuse may result in loosing rights under the provisions of warranty. When connecting device to power
source with cables with adequate cross-section should be used. Long-lasting output load capacity table should be
the ground for choosing adequate cables.
Optimal mounting parameters:
1. Minimal length from the ground > 1,5 m,
2. Minimal length from the wall and ceiling > 0,3 m,
3. Minimal length from the receiver > 0,2 m.
MAGNETIC_1CfT
www.sukcesgroup.pl
power supply:
230 V / 50 Hz
motor:
230 V / 50 Hz
phaze wire (power supply)
neutral wire (power supply)
1st direction (motor – brown wire)
2nd direction (motor – black wire)
neutral wire (motor - blue wire)
1. Manual work mode (Displays MAN symbol: standard mode without using time programming function.
2. Automatic mode (displays AUTO symbol): standard mode with activated automatic work time.
3. Random work mode (displays symbol): automatic mode with random time of work (15 minutes difference from
programmed time).
By pressing WORK MODE
button for about 3 seconds
work mode will change to
manual mode.
By pressing WORK MODE
button for about 3 seconds work
mode will change to automatic
mode.
By pressing WORK MODE
button for about 3 seconds
work mode will change to
random mode.
Pressing WORK MODE button will cause
for work mode to change again.

In order to fully explore available functions of MAGNETIC series please take a moment and read this manual before using the device. MAGNETIC transmitters
are compatible with all YOODA brand devices.
Setting current time
MAGNETIC_1CfT
www.sukcesgroup.pl
Time can be set only when device is in manual working mode.
Longer than 60 seconds pause between series of button clicks during programming will cause device to switch off
from time setting mode without saving any changes.
By pressing WORK MODE
button choose
manual work mode.
Press and hold L1 TIMER
PROGRAMMING button for about
3 seconds (hour starts to flash).
Using UP / DOWN
buttons set hour.
By pressing L1 TIMER
PROGRAMMING button
switch to minute setting
(minute starts to flash).
Using UP / DOWN buttons
set minute.
By pressing L1 TIMER
PROGRAMMING button
switch to day setting
(day starts to flash).
Using UP / DOWN buttons
set current day of the week.
By pressing P1 CONFIGURATION CHANGE
button for about 3 seconds
confirm new setting.
Pressing L1 TIMER
PROGRAMMING button
will start the clock.
Changing automatic opening and closing time
1. Difference between automatic time of roller shutter opening and closing cannot be shorter than 32 minutes. In case of
smaller than minimal time difference fault message will appear.
2. Changes to opening and closing time can be done only in automatic mode.
3. Longer than 60 seconds pause between series of button clicks during programming will cause device to switch off
from time setting mode without saving any changes.
4. If while setting time of automatic opening or closing ‘--:--‘ symbol appears, it means that this time is not active in
automatic mode.
5. To leave time programming mode without saving any changes press STOP button.
By pressing WORK MODE
button choose random
work mode.
Press L1 TIMER PROGRAMMING
button for 3 seconds. Current
opening time will be displayed.
Press L1 TIMER
PROGRAMMING button
single time (hour of
opening flashes).
Using UP / DOWN buttons
set hour.
By pressing L1 TIMER PROGRAMMING
button switch to minute setting
(minute starts to flash).
Using UP / DOWN buttons
set minute.
By pressing WORK MODE button
switch to setting closing time.
Using UP / DOWN buttons
set hour.
By pressing L1 TIMER PROGRAMMING
button switch to minute setting
(minute starts to flash).
Using UP / DOWN buttons
set minute.

Programming transmitters
1. Longer than 6 seconds pause between series of button clicks during programming will cause device to switch off from
programming mode without saving any changes.
2. Procedure described below is to be used for programming first and all other transmitters. Receiver can hold in its
memory up to 20 different transmitters. Programming another transmitter will cause for the first transmitter on the list
of 20 already programmed to be deleted.
In order to fully explore available functions of MAGNETIC series please take a moment and read this manual before using the device. MAGNETIC transmitters
are compatible with all YOODA brand devices.
MAGNETIC_1CfT
www.sukcesgroup.pl
Changing automatic opening and closing time
Instructions described above, showing how to
set automatic opening and closing time, should
be repeated for every day of the week.
By pressing P1 CONFIGURATION CHANGE
button confirm new setting. Control unit
automaticaly switches to setting time of
automatic opening and closing for next
day of the week.
After setting automatic opening and closing time
for every day of the week press and hold P1
CONFIGURATION CHANGE button for about
3 seconds to confirm all changes
(current time starts to flash).
Switch power on. Press and hold WORK MODE button
for about 6 seconds
('LEAr' sign start to flash).
Press STOP button
('LEAr' sing stops to flash).
Press STOP button on transmitter
that is beeing programmed.
'good' sign will flash three times
confirming, that new transmitter
was succesfully programmed.
Deleting transmitter
Deleting all transmitters
Longer than 6 seconds pause between series of button clicks during programming will cause device to switch off from
deleting mode without saving any changes.
Proceeding with this instruction will cause for all transmitters to be deleted form receivers memory.
Switch power on. Press and hold STOP / DOWN
buttons at the same time
for about 6 seconds
('SET2' sign starts to flash).
'good' sign will flash three times
confirming, that all programmed
transmitter were successfully deleted.
Switch power on. Press and hold WORK MODE button
for about 6 seconds
('LEAr' sign starts to flash).
Press STOP button
('LEAr' sing stops to flash).
Press DOWN button on transmitter
that is beeing deleted.
'good' sign will flash three times
confirming, that new transmitter
was successfully deleted.

When impulse mode is activated, single push of UP or DOWN button forces motor to make single part of a full turn, and
when UP or DOWN button is being held for 2 seconds it will force motor to run constantly (to the pint it reaches its limit
position).
Procedure should be performed when motor works in direction other than expected (e.g. when pressing UP button roller
shutter is being lowered).
Switch power on. Press and hold STOP and UP
buttons at the same time
for about 6 seconds
('SET3' sign starts to flash).
'good' sign will flash three times
confirming, that impulse mode
has been activated.
Repeat these steps
to deactivate pulse mode.
Switch power on. Press and hold UP / DOWN buttons
at the same time
for about 6 seconds
('SET1' sign starts to flash).
After 6 seconds symbol “good” will flash
3 times on the display signalizing, that
motors direction of rotation was
successfully changed.
Changing motors direction
Activating impulse mode
In order to fully explore available functions of MAGNETIC series please take a moment and read this manual before using the device. MAGNETIC transmitters
are compatible with all YOODA brand devices.
MAGNETIC_1CfT
www.sukcesgroup.pl