Yoshitake GD-26 Series User manual

PDT-008o
MODEL GD-26, GD-27, GD-28, GD-29 series
Pressure Reducing Valve
PRODUCT
MANUAL
Thank you very much for choosing the Yoshitake’s product. To ensure the correct and safe use of the product,
please read this manual before use. This manual shall be kept with care for future reference.
The symbols used in this manual have the following meanings.
Warning
This symbol indicates a potentially hazardous situation that, if not avoided, could
result in death or serious injury.
Caution
This symbol indicates a hazardous situation that, if not avoided, may result in
minor or moderate injury or may result in only property damage.
Table of Contents
1. Usage of the Product·················································· 1
2. Specifications
2.1 Specifications·················································· 1 - 3
2.2 Nominal size selection ······································ 3 - 5
2.3 Flow rate characteristics chart ································ 5
2.4 Pressure characteristics chart································· 6
2.5 Noise characteristics chart ····································· 6
3. Dimensions and weights········································ 7 - 10
4. Operation································································10
5. Installation
5.1 Piping example···················································10
5.2 Precaution for installation································ 11 - 12
6. Operation procedure
6.1 Precaution for operation ······································· 12
6.2 Adjusting procedure······································· 12 - 13
7. Maintenance
7.1 Troubleshooting··················································13
7.2 Precaution for maintenance and inspection ·············· 14
7.3 Disassembly ················································14 - 15
7.4 Precaution for reassembly ···································· 15
7.5 Strainer cleaning procedure ·································· 16
8. Exploded view····················································17 - 18

1
PDT-008o
1.
Usage of the Product
This product can be used for a wide range of pressure control in a water supply system and others for the
general households, multistoried buildings, industrial plants, and plant facilities.
2
. Specifications
2.1 Specifications
Model GD-26-NE GD-27-NE GD-27-N GD-27F-N GD-28-NE GD-29-NE
Nominal size 15A - 50A 25A - 100A 125, 150A 15A - 50A 25A - 100A
Application Cold and hot water
Inlet pressure 1.0 MPa or less 1.6 MPa or less
Reduced
pressure
A 0.05 - 0.35 MPa 0.05 - 0.20 MPa 0.05 - 0.35 MPa
B 0.30 - 0.70 MPa 0.20 - 0.50 MPa 0.30 - 0.70 MPa
Min. differential
pressure 0.05 MPa
Max. pressure
reduction ratio 10:1 *
Max.
temperature 90°C 80°C 90°C
Material
Body CAC406
Valve seat CAC406
Valve disc FKM NBR FKM
Diaphragm EPDM NBR FKM EPDM
Pipe end core None
Connection JIS Rc
screwed
JIS 10K FF
flanged
JIS Rc
screwed
JIS 16K FF
flanged
* The maximum differential pressure of the products of 125A and 150A is 0.8 MPa.
The products of the nominal size 15A to 50A incorporate a strainer (40 mesh).
Pressure gauge connection port is JIS R1/8.
All the above models conform to the standard of the Japanese Water Supply Act.
Available with GD-26-NED and GD-27NED with wetted parts made of stainless steel.

2
PDT-008o
Model GD-26L-NE
Nominal size 15A - 50A
Application Cold and hot water
Inlet pressure 1.0 MPa or less
Reduced
pressure
A 0.05 - 0.35 MPa
B 0.30 - 0.70 MPa
Min. differential
pressure 0.05 MPa
Max. pressure
reduction ratio 10:1
Max.
temperature 40°C
Material
Body CAC406
Valve seat CAC406
Valve disc FKM
Diaphragm EPDM
Pipe end core
Used both for polyvinyl chloride lined steel pipe and powdered polyethylene lined steel pipe
Connection JIS Rc screwed
The products of the nominal size 15A to 50A incorporate a strainer (40 mesh).
Pressure gauge connection port is JIS R1/8.
The GD-26L-NE conforms to the standard of the Japanese Water Supply Act.
Model GD-26S GD-27S GD-26S-NE GD-27S-NE GD-28S GD-29S
Nominal size 20A - 50A 20A - 100A 20A - 50A 20A - 100A 20A - 50A 20A - 100A
Application Cold and hot water
Inlet pressure 1.0 MPa or less 1.6 MPa or less
Reduced
pressure
A 0.05 - 0.35 MPa
B 0.30 - 0.70 MPa
Min. differential
pressure 0.05 MPa
Max. pressure
reduction ratio 10:1
Max.
temperature 90°C
Material
Body SCS13
Valve seat SCS13
Valve disc EPDM FKM EPDM
Diaphragm EPDM
Pipe end core None
Connection JIS Rc
screwed
JIS 10K FF
flanged
JIS Rc
screwed
JIS 10K FF
flanged
JIS Rc
screwed
JIS 16K FF
flanged
The products of the nominal size 15A to 50A incorporate a strainer (40 mesh).
Pressure gauge connection port is JIS R1/4.
Models conforming to Japanese Water Supply Act are GD-26S-NE and GD-27S-NE. These valve discs
are made of FKM.

3
PDT-008o
2.2 Nominal size selection
Procedure of nominal size selection
1. If the pressure difference before and after the product is 0.15 MPa or more, choose the nominal size
from the rated flow table below.
Rated flow table (The pressure difference before and after the product is 0.15 MPa or more)
Nominal size 15A 20A 25A 32A 40A 50A 65A 80A 100A 125A 150A
Rated flow (L/min) 30 40 60 100 150 250 300 450 700 1600 1800
2. If the pressure difference before and after the product is less than 0.15 MPa, choose the nominal
size from the nominal size selection charts (for 15A - 50A, 65A - 100A, and 125A - 150A) below.
Nominal size selection chart
Nominal size 15A - 50A
Caution
Please confirm that the indications on the product correspond with the specifications
of the ordered product model before use.
* If they are different, please contact us without using the product.
Flow rate
L/min
Inlet pressure
Reduced pressure + 0.2 MPa
Reduced pressure + 0.1 MPa
Reduced pressure + 0.05 MPa
Nominal size
1.0 -
1.6 MP
a
Reduced pressure MPa

4
PDT-008o
Nominal size 65A -100A
Flow rate L/min
Inlet pressure
Reduced pressure + 0.2 MPa
Reduced pressure + 0.1 MPa
Reduced pressure + 0.05 MPa
Nominal size
1.0 - 1.6 MPa
Reduced pressure MPa

5
PDT-008o
Flow
rate
Set pressure
Shut-off pressure rise
(0.02 MPa)
Min. adjustable
flow rate
Rated flow
Offset
Reduced pressure
Nominal size 125A -150A
3.3 Flow rate characteristics chart
Offset
Nominal size
Pressure range
Reduced
pressure range
Offset
15A - 100A
A 0.05 - 0.35 MPa 0.05 MPa or less
B 0.30 - 0.70 MPa 0.10 MPa or less
125A - 150A
A 0.05 - 0.20MPa 0.07 MPa or less
B 0.20 - 0.50MPa 0.12 MPa or less
Nominal size
Inlet pressure
Reduced pressure + 0.2 MPa
Reduced pressure + 0.1 MPa
Reduced pressure + 0.05 MPa
Flow rate L/min
0.5
-
1.0 MPa
Reduced pressure MPa

6
PDT-008o
2.4 Pressure characteristics chart
This chart shows variation in the reduced pressure when the inlet pressure of 0.60 MPa is changed
between 0.15 MPa and 1.0 MPa after the reduced pressure is set at 0.10 MPa.
2.5 Noise characteristics chart (Fluid: Water)
Inlet pressure MPa
Nominal size 15A - 25 A
Inlet pressure: 0.6 MPa
Reduced pressure: 0.2 MPa
Flow rate L/min
Nominal size: 15 A
Nominal size: 20 A
Nominal size: 25 A
Nominal size 32A - 50 A
Flow rate L/min
Nominal size: 32 A
Nominal size: 40 A
Nominal size: 50 A
Nominal size 65A - 100 A
Flow rate L/min
Nominal size: 65 A
Nominal size: 80 A
Nominal size: 100 A
Reduced pressure MPa
Inlet pressure: 0.6 MPa
Reduced pressure: 0.2 MPa
Inlet pressure: 0.6 MPa
Reduced pressure: 0.2 MPa
Inlet pressure: 0.6 MPa
Reduced pressure: 0.2 MPa
Noise
Noise
Noise

7
PDT-008o
3
.
Dimensions and
Weights
Model GD-26-NE, GD-28-NE, GD-26L-NE, GD-26S, GD-26S-NE, GD-28S
Model GD-26-NE, GD-28-NE, GD-26L-NE
Nominal
size d L H1H Weight (kg)
15A Rc 1/2 115 37.5 159.5 1.6
20A Rc 3/4 120 38.5 159.5 1.7
25A Rc 1 135 41 170 2.1
32A Rc 1 1/4 180 57 224 4.0
40A Rc 1 1/2 180 57 224 4.4
50A Rc 2 200 61 239.5 6.5
Model GD-26S, GD-26S-NE, GD-28S
Nominal
size d L H1H Weight (kg)
20A Rc 3/4 135 41 170 2.2
25A Rc 1 135 41 170 2.2
32A Rc 1 1/4 180 57 224 4.7
40A Rc 1 1/2 180 57 224 4.5
50A Rc 2 200 61 239.5 6.5

8
PDT-008o
Model GD-27-NE, GD-29-NE, GD-27S, GD-27S-NE, GD-29S
Nominal size 25A - 50A
Nominal size 65A - 100A
Model GD-27-N, GD-27F-N
Nominal size 125A, 150A

9
PDT-008o
Model GD-27-NE, GD-27-N, GD-27F-N
(mm)
Nominal size
L H1H JIS 10K FF flanged Weight
(kg)
d D C t n-φh
25A 160 41 170 25 125 90 14 4-19 5.1
32A 200 57 224 32 135 100 16 4-19 7.5
40A 200 57 224 40 140 105 16 4-19 7.7
50A 220 61 239.5 50 155 120 16 4-19 10.9
65A 220 77 329 65 175 140 18 4-19 20.0
80A 230 82 345 80 185 150 18 8-19 22.0
100A 270 94 412 100 210 175 18 8-19 33.0
125A 360 148 771 125 250 210 20 8-23 90.0
150A 380 148 771 150 280 240 22 8-23 97.0
・The nominal size of GD-27-NE is 25A to 100A. The nominal size of GD-27-N and
GD-27F-N is 125A and 150A only.
Model GD-29-NE
(mm)
Nominal size L H1H JIS 16K FF flanged Weight
(kg)
d D C t n-φh
25A 160 41 170 25 125 90 14 4-19 5.1
32A 200 57 224 32 135 100 16 4-19 7.5
40A 200 57 224 40 140 105 16 4-19 7.7
50A 220 61 239.5 50 155 120 16 8-19 10.9
65A 220 77 329 65 175 140 18 8-19 20.0
80A 234 82 345 80 200 160 20 8-23 24.0
100A 278 94 412 100 225 185 22 8-23 36.5
Model GD-27S, GD-27S-NE
(mm)
Nominal size L H1H JIS 10K FF flanged Weight
(kg)
d D C t n-φh
20A 160 41 170 20 100 75 14 4-15 3.9
25A 160 41 170 25 125 90 14 4-19 4.8
32A 200 57 224 32 135 100 16 4-19 8.0
40A 200 57 224 32 140 105 16 4-19 8.3
50A 220 61 239.5 50 155 120 16 4-19 10.8
65A 220 77 329 65 175 140 18 4-19 20.6
80A 230 82 345 80 185 150 18 8-19 22.0
100A 270 94 412 100 210 175 18 8-19 34.5

10
PDT-008o
Model GD-29S
(mm)
Nominal size
L H1H JIS 16K FF flanged Weight
(kg)
d D C t n-φh
20A 160 41 170 20 100 75 14 4-15 3.9
25A 160 41 170 25 125 90 14 4-19 4.8
32A 200 57 224 32 135 100 16 4-19 8.0
40A 200 57 224 32 140 105 16 4-19 8.3
50A 220 61 239.5 50 155 120 16 8-19 10.8
65A 220 77 329 65 175 140 18 8-19 20.6
80A 234 82 345 80 200 160 20 8-23 25.0
100A 278 94 412 100 225 185 22 8-23 36.5
4
.
Operation
The spring is compressed by the adjusting screw,
the diaphragm is pushed down, and thereby the
disc directly connected to it is opened.
Fluid coming in from the inlet side flows out from
the upper part of the disc to the outlet side, and
passes through the reduced pressure detection
hole, and is led to the bottom of the diaphragm.
The load of the spring and the reduced pressure
act to the diaphragm, and the upper and lower
force keeps a balance and regulates the valve
opening. As a result, the diaphragm keeps the
reduced pressure constant.
5
.
Installation
5.1 Piping example
* Install a strainer on the inlet side of the pressure reducing valve of the nominal size 65A to 150A.
Outlet side
By-pass
Globe valve
Pressure gauge
Pressure
gauge
Safety relief valve
Inlet side
Stop
valve
GD-26-NE
Pressure reducing valve
Stop
valve
Adjusting
screw
Diaphragm
Reduced pressure
detection hole
Disc
Spring

11
PDT-008o
5.2 Precaution for installation
Warning
1. Since the products of the nominal size 125A and 150A are heavy, securely support them using lifting
devices or the like when installing. See the product weight specified in “3. Dimensions and Weights.”
* Failure to follow this notice may cause a falling accident of the product, resulting in an injury.
2. When installing a safety relief valve for equipment protection at the outlet side of the product, connect
a blow-off pipe to the outlet side of the safety relief valve, and lead it to a place where there is no risk of
physical damage even if fluid blows out.
* Failure to follow this notice may result in injury and scalds in the event that high temperature fluid
blows out.
Caution
1. Do not disassemble the product unless it is necessary.
* Unnecessary disassembly prevents the product from functioning properly.
2. Before installing the product in the piping, be sure to remove foreign substances and scale from the
piping. Keep foreign substances from entering the piping, including seal tape or liquid seal agent for
piping connection.
*Ingress of foreign substances, scale or seal agent into the product leads to valve leakage or
malfunction of the product.
3. If components having negative influence on internal parts are included in fluid or surroundings,
deterioration of rubber parts is accelerated and then outside leakage or functional disorder is caused.
4. Be sure to install a strainer at the inlet side of the product of nominal size 65A to 150A.
*Ingress of foreign substances or scale into the product leads to malfunction of the product. It is
recommended to use a strainer of 60 mesh or more.
5. Install a safety relief valve for equipment protection at the outlet side of the product.
* Failure to follow this notice may result in damage of the equipment.
6. Be sure to install pressure gauges at the inlet and outlet sides of the product.
* Failure to follow this notice hampers correct pressure adjustment.
7. If a quick operating valve such as a solenoid valve is installed, place it at a distance of at least 3
meters from the product.
* Failure to follow this notice may result in malfunction or a drastically shortened service life of the
product.
8. Install the product properly by checking the inlet, outlet and proper posture. The product can be
installed either horizontally or vertically (nominal size 15A to 100A). In the case of the nominal size
125A and 150A, install the product horizontally.
* Installing the product in wrong directions prevents the product from functioning properly.
9. Install pipes so that excessive load, torque or vibration is not applied to the product.
10. It is recommended to use a bronze or stainless steel nipple for the outlet side of the GD-26-NE or
GD-28-NE when installing.
* If a steel pipe (lined steel pipe) is used for the outlet side of the product, corrosion (rust tubercle, etc)
at the end of the steel pipe is increased year by year, which clogs the reduced pressure detection hole
at the outlet side of the product and result in insufficient fluid flow.
11. The product can be installed either horizontally or vertically (nominal size 15A to 100A). In case of nominal
size 125A and 150A, install the product horizontally.
12. A space more than the value shown as H2in the table below is required for disassembly and inspection.
A space more than the value shown as H3in the table below is required for the inspection of the built-in
strainer (nominal size 15A to 50A).
13. For two-stage pressure reduction, keep a distance of at least 3 meters between each product.
*Failure to follow this notice may prevent the product from functioning properly due to malfunction.
Model GD-26-NE, GD-27-NE, GD-28-NE, GD-29-NE, GD-27-N, GD-27F-N, GD-26L-NE
(mm)
Nominal size 15A 20A 25A 32A 40A 50A 65A 80A 100A 125A 150A
H2240 240 250 300 300 320 450 450 550 970 970
H380 80 90 120 120 150 - - - - -

12
PDT-008o
Model GD-26S, GD-27S, GD-28S, GD-29S, GD-26S-NE, GD-27S-NE
(mm)
Nominal size
20A 25A 32A 40A 50A 65A 80A 100A
H2250 250 300 300 320 450 450 550
H390 90 120 120 150 - - -
6
.
Operation procedure
6.1 Precaution for operation
Caution
1. Before leading fluid into the product, close the stop valves at the inlet and outlet of the product and
remove foreign substances and scale from the piping completely by using a bypass line.
* Failure to follow this notice may prevent the product from functioning properly due to the ingress of
foreign substances and scale into the product.
2. To adjust the set pressure, turn the adjusting screw slowly.
* Failure to follow this notice may result in damage to the product and other equipment due to hunting
or other cause.
3. If closing outlet side of the product and keeping fluid inside the product for an extended period, sliding
parts become stuck and it causes malfunction of the product.
*Check if the product operates normally when resuming the product.
4. When the product is not used for an extended period, completely discharge fluid from the product and
pipes, and close the stop valves at the inlet and outlet sides of the product.
* Failure to follow this notice causes malfunction of the product due to rusting inside the product and
the pipes.
5. The set pressure may be affected by ambient temperature (external temperature) and fluid temperature.
Install pipes so that the product may not be exposed to direct sunlight.
6.2 Adjusting procedure
Following a wrong adjusting procedure may cause hunting, scale problems or other problem, and can
heavily damage the main parts of the valve. To avoid these problems, be sure to follow the procedure
given below
1. Close the stop valves at the inlet and outlet sides of the reducing valve, and take adequate time to
blow out fluid by using a bypass line. In doing this, adjust the opening of the globe valve in the
by-pass pipe so as not to blow out the safety relief valve. After the end of blowing, close the globe
valve without fail.
Warning
When the product is used for hot fluid, do not touch the product with bare hands.
* The product having hot fluid may scald your skin.

13
PDT-008o
2. Fully open the stop valve at the inlet side slowly, and open the stop valve at the outlet side so that a
little fluid can flow through.
3. Remove the domed cap nut [17] (loosen the nut [41] in the case of nominal size 125A and 150A),
and turn the adjusting screw [14] while watching the pressure gauge at the outlet side.
•Turn the adjusting screw to the right (clockwise) to increase the reduced pressure.
•Turn the adjusting screw to the left (counterclockwise) to decrease the reduced pressure.
4. Fully open the stop valve at the outlet side slowly.
5. After the adjustment is complete, tighten the domed cap nut [17] (nut [41] in the case of the nominal
size 125A and 150A).
8
. Maintenance
7.1 Troubleshooting
Trouble Cause Remedy
Abnormal pressure
rise at the outlet side.
1. Foreign substances stuck between
the disc [8] and the valve seat [3],
or scratch on them.
1. Disassemble the product and remove
the foreign substances. If scratch is
observed on the valve disc or valve
seat, replace it.
2. The O-ring [6] is damaged. 2. Replace the O-ring.
3. The diaphragm [9] is damaged. 3. Replace the diaphragm.
4. There is a leakage from the globe
valve of the by-pass line.
4. Repair or replace the globe valve.
Reduced pressure
does not reach the
desired value.
1. The working pressure is improper. 1. Correct the working pressure. (See
“2.1 Specifications” on Page 1.)
2. The nominal size of the product is
too small for the flow rate for use.
2. Replace the product with the proper
nominal size. (See “2.2 Nominal size
selection” on Page 3.)
3. Pressure adjustment is improper. 3. Readjust the pressure in accordance
with the given procedure. (See “6.2
Adjusting procedure” on Page 12.)
4. Strainer [10] built in the product is
clogged.
4. Clean the strainer. (See “7.5 Strainer
cleaning procedure” on Page 16.)
5. The strainer installed at the inlet
side of the product is clogged.
5. Clean the strainer.
Outside leakage
1. Bolt [18] or [39] is loosened. 1. Tighten the bolts.
2. O-ring [30] is damaged. 2. Replace the O-ring.
3. Strainer cap [11] or plug [31] is
loosened.
3. Tighten the strainer cap or plug.
Abnormal sound
1. The nominal size of the product is
too large for the specifications of
the system.
1. Replace the product with the proper
nominal size. (See “2.2 Nominal size
selection” on Page 3.)
2. The pressure reduction ratio is too
large or the maximum pressure
difference is exceeded.
2. Reduce pressure in two stages. (See
“2.1 Specifications” on Page 3)
3. Air binding has occurred. 3. Install an air vent device.
4. A quick operating valve is located
near the product.
4. Keep a distance between them as
large as possible. (3 m at least)
Most of problems with the pressure reducing valve are caused by foreign substances and scale in the
piping. Avoid the ingress of dust and dirt to the product with caution.
A phenomenon similar to valve failure could occur due to the failure of the pressure gauge, leakage or
insufficient tightening of the globe valve in the by-pass line, clogging of the strainer, and other causes.
Check the above possible causes and take a proper remedy and preventive measures.

14
PDT-008o
7.2 Precaution for maintenance and inspection
Warning
1. Completely discharge the pressure inside of the product, piping and equipment before disassembly and
inspection. Disassembly and inspection must be done by experienced professional or valve
manufacturer.
* Failure to follow this notice may result in scalds, injury or contamination on the surroundings due to the
residual pressure.
2. If fluid is hot, do not touch the product directly with bare hands.
* Failure to follow this notice may result in scalds or injury.
Caution
1. If problem occurs for a cause other than listed in "7.1 Troubleshooting" on Page 13, please contact us.
2. When the product is disassembled, internal fluid flows out. Receive it in a container.
* Failure to follow this notice may result in making the surroundings dirty.
3. Synthetic rubber is a consumable part. The replacement interval of the synthetic rubber part greatly
varies depending on the use conditions. The general guide for the replacement interval is shown below.
Service life Part name
Three years Diaphragm [9], O-ring [6], Disc [8]
Five years O-ring [20], [24], [26], [28], [30], [45]seal washer [42]
7.3 Disassembly
1. Remove the domed cap nut [17] (loosen the nut [41] in the case of nominal size 125A and 150A),
turn the adjusting screw [14] counterclockwise, and set the spring [15] free (no load).
2. Remove the bolts [18] of the spring chamber [2] and remove the spring chamber [2]. Then take out
the spring [15] and the spring plate [13].
3. Remove the nut [22], and then the diaphragm retainer [12], and diaphragm [9].
4. Remove the set screws [25] (bolts [25] in the case of nominal size 65A to 150A) of the valve seat [3],
and remove a set of the valve seat (valve seat [3], spindle [4], disc [8], and O-ring [28]).
Nominal size 15A to 50A: Attach the diaphragm retainer [12] to the spindle [4], and pull it up.

15
PDT-008o
Nominal size 65A to 150A: Screw the bolt into the valve seat [3], and pull it up.
(5) Secure the part A of the spindle [4] (two faces), loosen the U-nut [29] with a tool, and remove the disc
[8], and O-ring [28].
7.4 Precaution for reassembly
Caution
1. Check to see that there is no foreign substances inside the body and on each part.
*Foreign substances prevent the product from functioning properly. To avoid the problem, remove
foreign substances.
2. Check that there is no scratch on the disc or O-ring.
*A scratch on the relevant part prevents the product from functioning properly. Replace the damaged
part.
3. Apply silicone grease (harmless to humans) to the O-ring.
*Failure to follow this notice may damage the O-ring.
Assemble the parts in reverse order of disassembly.
Tighten the bolts [18] of the spring chamber [2] evenly in the diagonal order.
U-nut
Part A
Washer of disc
O-ring
Disc cover
D
isc

16
PDT-008o
7.5 Strainer cleaning procedure
Warning
1. If fluid is hot, do not touch the product directly with bare hands.
* Failure to follow this notice may result in scalds.
Caution
1. Clean the strainer regularly at least once or twice a year.
* Too much deposit of scales or the like decreases the flow rate, which prevents the product from
functioning properly.
2. When the strainer cap is removed, receive fluid in a container. (See the Figure below.)
1. Close the stop valve at the inlet side and open the stop valve at the end, and remove the internal
pressure from the product completely.
2. Turn the strainer cap counterclockwise, and remove it.
3. Remove the strainer from the strainer cap, and wash it in water, and remove deposited scale.
4. After cleaning, reinstall the strainer and strainer cap in the body.
5. Open the stop valve at the inlet side, and check that there is no leakage from the strainer cap. When
there is a leakage, replace the O-ring.
6. Open the stop valve at the end, and check that the product operates normally.
Container
O-ring
Strainer
Strainer cap

17
PDT-008o
8
.
Exploded view
Nominal size 15A - 50A
Note) The parts shown in the rectangle boxes are available as consumable supply
Washer of disc

18
PDT-008o
Nominal size 65A - 150A
Note) The parts shown in the rectangle boxes are available as consumable supply.