Youcan Robot BW Space Pro User manual

BW Space Pro Max
Underwater Drone
V 1.0
User Manual

Contents
01
02
04
07
10
13
14
16
17
21
23
25
26
Disclaimer and Safety Instructions
Technical Specifications
Maintenance and Care
Contact Us
Remote Controller
Introduction of Oceaneye APP
Product Overview
Preparation
Shut down and Retrieval
Photos and Videos Exportation
Installation and Use of the Mechanical Arm
Connecting
Product List

01
Disclaimer and Safety Instructions
l. In order to protect the legitimate rights and interests of users, please read
carefully the instruction book, disclaimers and safety instructions provided
with this product before using it. Please be sure to operate this product
according to instruction book and safety instructions, and Youcan Robot
(Shanghai) Co., Ltd. owns the right to revise the above items.
2. Once you start using this product, you shall be deemed to have read,
understood,recognized and accepted all terms and contents of the
instruction book, disclaimers and safety instructions. The user shall only
utilize product solely for legitimate purposes and be responsible for their
own actions and all consequences.
3. In using this product, you're supposed to strictly comply with including
but not limited to requirements we have mentioned in safety instructions.
Users shall shoulder all responsibilities and losses caused by the violation of
safety instructions, including all personal injuries, accidents, property losses,
legal disputes and all other issues that may result in interest conflicts, and
Youcan Robot (Shanghai) Co., Ltd shall not bear any responsibility.
4. Youcan Robot (Shanghai) Co., Ltd. shall not be liable for any breach of law
directly or indirectly committed by our users.
1. Please check the product before use, including but not limited to the
durability of the parts, cracks and abrasion of the device body and propeller,
battery life, etc. When any abnormal situations are found, please stop using
and replace the accessories immediately.
2. Please do not use this product in harsh environments, such as strong wind,
heavy rain, thunder, fog, snow, tsunami, low temperature, etc.
3. The product shall not be used in the cases of alcohol drinking, fatigue,
seasickness, medicine taken, physical discomfort, etc.
4. In using this product, please keep away from the environment of high
electromagnetic interference, such as WiFi hot spots and high-power
transmission equipment.
Disclaimer
Safety Instructions

02
5. In using this product, please ensure your own safety and wear the life
jacket (self-provided), and keep away from dangerous areas and dangerous
marine life, such as the tiger shark and the great white shark.
6. When the product gives the low battery notification, you should stop using
the device in time. Please do not panic in case of incidents, such as outages,
broken ropes, etc. BW Space Pro Max will automatically come to the surface
by buoyancy.
7. Minors shall be accompanied by parents to use products or accessories to
avoid dangers.
8. Please do not use this product to take pictures of others or private
areas without permission, and do not use this product for reconnaissance,
espionage or military activities without authorization.
Please visit www.youcanrobot.com for the latest disclaimer and safety
instructions.
Product List
1
2

03
4 5
10
9
8
12
345
6 7 8
910
11
7
BW Space Pro Max Underwater Drone
Stand and Handle
Adapter Cable Sealing Lubricant and Sealing Ring
Wrench and other Tool Kits (used when installing the tether)
Charger Mechanical Arm Adapters and Mounting Bases
WiFi Repeater
Remote Controller
Tether Winder
11

04
Product Overview
BW Space Pro Max
WiFi Repeater
Vertical propeller
Vertical propeller
Vertical propeller
Communication/
Charging interface
Protection wing
Protection wing
Safety bolt
Camera
Horizontal propeller Horizontal propeller
LED LightLED Light
Working indicator
Power switch
Battery indicator
Type-c charging port Charging indicator
Cable connector
WANLAN

05
3. Description of the status of the power indicator of the WiFi Repeater:
M8 screws
M8*1 spacer
Handle
M8*1 spacer M8 screw nut
M8 cleat nut
Stand
BearingMagnet attachment point
Tether Winder
Cautions
Low
High
Battery
1. WiFi repeater can NOT operate in the water,so please do not put it into water.
2. WAN interface: Network interface, providing network signal for underwater
live broadcast.
LAN interface: can be connected to computers, notebooks and other equipment.
A B
when the power is lower than 25%,
the red light is on

06
【How to install and remove the handle】
•Insert the handle into the installation hole, insert and press the plastic
buckle on the inside of the winder; when removing, lift the buckle from the
inside of the winder, and then remove the handle.
• Align the four bases of the WiFi Repeater with the magnet attraction points
of the tether winder and fix them on the surface of the winder.
【WiFi Repeater xing method】
【How to install the Stand】
1. M8*1 gasket into the M8 screw from the A side and insert it
into the central hole of the tether winder;
2. Load the M8*1 gasket and bearing from the B side, and
then use the M8 screw nut to lock;
3. Install the bracket on the B side, and use a wrench to lock
the M8 cleat nut.
Tutorial Video

07
Instructions of Sealing Lubricant and Sealing Ring
• Apply sealing lubricant evenly to the sealing ring of communication/
charging interface and thread before using.
1. Seal the drone tightly and enhance the waterproof performance;
2. Act as a lubricant, making it easier to access the plug and reduce the loss
of the sealing ring;
The sealing ring is the spare part of the drone connector. When the original
sealing ring is damaged, please replace it in time to maintain waterproof.
【The functions of sealing lubricant】
Cautions
Preparation
Charging
【Charging of BW Space Pro Max】

08
Insert the connector of the charger with 4-pin jacks into the BW Space Pro
Max charging port, the power indicator turns red, indicating that charging
is in progress; when the power indicator turns green, it indicates that the
charging is complete.
【Charging of WiFi Repeater】
Connect the Type-c cable to the charging port of the WiFi Repeater, start
charging, and the red indicator light will turn on; the indicator light will turn
off, indicating that the charging is fully charged.
Please Turn off the Power
when charging
Cautions
1. When connecting the device, please align the socket first, and then rotate
the nut until it is tightened; when disassembling the connector, unscrew the
nut firstly ,then pull out the socket.
Tether connector Drone connector
Align
2. Prohibited to touch the connector front end with wet or sweaty hands;
water should be dried if there is water on the connector.
3. Charge the BW Space Pro Max and WiFi Repeater every three months.
4. Make sure to use the special charger provided by Youcan Robot.
1 2

09
Cautions
Please Fully Charge for the
First Time Use
Please Charge Once Every
Three Months 100%
Download Oceaneye APP
•Visit Youcan Robot website to download the Oceaneye APP：
https://www.youcanrobot.com/servicesupport
• The iOS system supports version 10.3 or above, and the Android system
supports Android 6.0 or above;
• Since the software is constantly updated and iterated, please go to the
official website or download center to update the software version in time.
3 4

10
Connecting
Connect the equipment
1. Insert the 4-pin jack connector of the tether into the BW Space Pro Max
communication port, and the round hole connector into the WiFi Repeater,
and activate the WiFi Repeater power button. The indicator light of the WiFi
Repeater turns green, and the connection is complete.
Buckle the anti-lost ring on the tether to the safety bolt at the tail of the
drone to increase the tether's anti-fixation strength.
Youcanrobot-5G
Siwimate
Youcan-5F8901-
Wi-Fi
Wi-Fi设置
选取⽹络…
Youcan-*****-5G
Youcan-*****
Connect to WiFi
Access the mobile phone WiFi connection interface,
select Youcan-****-5G(Recommended) or Youcan-****,
enter the password: 12345678.
Cautions

11
Open Oceaneye App
OCEANEYE
Help
Drone is ready to run
Start
Device Gallery Store My
Youcan-42915EE-5G
Open the Oceaneye APP, select the BW Space
Pro Max model, and click "Start". After the
connection is successful, slide to the right to
unlock, and the boot is successful. At this point,
you can use the APP to control the underwater
movement and shooting of the drone.
1. When the tether is inserted into BW Space Pro
Max, the drone will make a "beep beep" sound,
which is a normal phenomenon, indicating that
the power is normal;
2. If the APP connection fails, please confirm
whether the access permission of the Oceaneye
APP is enabled on the mobile phone:
Android phone, open "Settings", find "Apps and
Services" - "Apps " – “APP info”, and turn on the permissions of the Oceaneye
APP (This path is slightly different on different models of mobile phones,
please find the correct path according to your mobile phone, and enable
access rights for the Oceaneye APP);
iOS phone, open "Settings", find Oceaneye, click "Wireless Data", and enable
"Wi-Fi and Cellular Networks" or "Local Network".
Tips
3. In case of start failure, check the following things:
If the device is appropriately powered;
If the jack of the tether is connected to BW Space Pro Max or WiFi Repeater
jack appropriately;
Access the mobile phone WiFi connection interface and check to see if the
device is connected. If the connection fails, reconnect the WiFi Repeater.

12
Put the BW Space Pro Max into water
When connected to the device, please perform steps to prevent the drone
from being unusable due to incorrect operation, if Oceaneye APP interface
prompts that the boot need to be upgraded. (Note: Please do not disconnect
the tether of drone with the WiFi repeater in upgrading; After upgrading,
please disconnect the tether in order to restart the device).
【Boot Upgrade】
【Control system upgrade】
【Camera upgrade】
To continuously optimize the operative performance of BW Space Pro
Max, we will upgrade the control system of BW Space Pro Max from time
to time. When you open Oceaneye APP, if the screen prompts upgrading,
this indicates that the device or software is being upgraded, usually for a
duration of about 1 minute. Do not quit from the upgrading. In case of failed
upgrading, please exit the Oceaneye App, unplug the tether and reconnect
and restart the upgrading.
Youcan Robot will upgrade the BW Space Pro Max camera system from
time to time. If a prompt pops up and requires a camera to upgrade when
you enter Oceaneye APP, BW Space Pro Max will start downloading the
latest camera system and upgrade it. This process may take about 5 minutes.
Please do not disconnect the device and keep Oceaneye under operation in
the upgrade.
Important tips

13
If the APP or Drone crashed or stuck, try the following steps or methods:
Exit the Youcan Dive APP completely and re-enter the APP to connect the
drone.
Disconnect the tether of WiFi Repeater and the drone, reconnect the
tether and Oceaneye app.
Cautions
Click the " " button in the upper left comer of the Oceaneye APP, and BW
Space Pro Max will stop working.
Shut down
Shut Down and Retrieval
Drive the drone back to the shore or pull the tether back, disconnect the
tether of the BW Space Pro Max and WiFi Repeater which means a complete
shutdown.
When not using the drone or WiFi Repeater, Please remember to disconnect
the tether, otherwise the device will remain in standby mode and the
battery will continue to be consumed.
Retrieval
Cautions

14
Introduction of Oceaneye APP
w
N
S
E
45°
-45°
1
10
2
17 2222
13
6
21
23
12
4
19
15
8
11
3
18
14
75
2016
9
Depth60.66m Temp23° Device Connected
Return: Return to the APP Home page.
Operation mode: Display whether the current device is in control mode or
viewing mode, release the operation authority, switch to viewing mode, and
allow other devices to enter control mode.
Depth: Shows the underwater depth of BW Space Pro Max.
Note: The control mode only supports 1 person (1 mobile phone) control. In
viewing mode, only underwater images can be viewed, the drone cannot
be controlled.
WiFi Repeater battery life: Display the remaining battery capacity of WiFi
Repeater.
BW Space Pro Max.
BW Space Pro Max battery life: Display the remaining battery capacity of
Settings:Enter the settings interface, configure the control mode, camera,
view battery information, etc.
Temperature: Display underwater real-time temperature.
Device status: Displays the device connection status.
WiFi Repeater information: Display the connection status information of the
WiFi Repeater.
1
7
2
8
3
9
4
5
6

15
w
N
S
Ew
N
S
E
Depth60.66m Temp23° Device Connected
Depth60.66m Temp23° Device Connected
More: Mechnical arm and live stream function.
Open: Long press the button, the Mechnical arm will open continuously;
release the button, the mechanical arm will pause to open.
Close: Long press the button, the Mechnical closes continuously; release
the button, the Mechnical arm closes temporarily.
Gallery: Click the button to browse and manage photos and videos.
Taking pictures and recording videos: By clicking the icon, the function of
shooting and recording can be switched.
Start shooting: Click the button to take pictures or record videos.
Speed: Adjust the speed of the drone, divided into low, medium and high
levels.
Floating: Click the button, the machine will float to the surface of the water.
Pause: Click the button, the propeller stops working (the camera can still
take pictures and videos).
Pitch range: Adjust the attitude of the drone head to achieve -45°~45°pitch
shooting.
Light: Adjust the light intensity, 0-100 free adjustment.
Attitude: Display the attitude of the drone in front view, top view and side view.
Steel wheel: Divided into 3 Models, please refer to the control function
diagram in the APP interface (Settings - Control Settings - Joystick Settings)
Zoom:（This feature is only available for the BW Space Pro Max Zoom）
By placing and spreading two fingers on the screen will enlarge the image;
by placing and closing two fingers on the screen will reduce the image.
10
13
11
14
12
15
16
17
18
19
20
21
22
23

16
2. Depth Calibration: The atmospheric pressure of the drone's current
environment is used as the zero point for depth calibration. Please follow
the steps shown in the APP to complete the depth calibration and machine
calibration.
3. Due to product updates and upgrades, the user interface will be updated
from time to time, please use the downloaded version software interface as
the main one.
【Into mobile phone】
【Into computer 】(only support Windows system computer)
Select the photos and videos to be downloaded in the “Gallery” interface,
click to download, the photos selected will be saved in the mobile phone
album. For editing or other purposes, you can export the photos and videos
to your computer by connecting your phone and your computer.
If you want to delete the photos and videos in the drone's memory card,
please find "General Settings" in the Oceaneye APP setting and format the
SD card.
Before deleting materials, please ensure that important materials have
been downloaded and saved.
1. Visit https://www.youcanrobot.com/servicesupport to download the
Youcan Assistant software.
2. Connect the BW Space Pro Max and WiFi Repeater with tether, search
and connect the Youcan WiFi signal on the computer (Youcan-****- 5G or
Youcan-****，password 12345678） .
3. Open the Youcan Assistant and export the photos and videos to computer.
Photos and Videos Exportation
Cautions
Cautions
1. The sensitivity in the control settings refers to the sensitivity of the left and
right rotationof the machine, the higher the value, the more sensitive the
steering.

17
Remote Controller
Mobile phone holder
Joystick Setting
Charging indicator
Left joystick
Right joystick
Low-angle shoot
High-angle shoot
Speed up
Pause
Home
Speed Down
Zoom out
（ZOOM Model）
Zoom in
（ZOOM Model）
Brightness
reduction
Open
Photo Record
Close
Brightness
enhancement
【Joystick setting】The default is Model 1; press once to switch to Model 2;
press again to switch to Model 3.
【Low-angle shoot】Set the pitch angle of 0 °~45 °, and the larger the number,
the larger the angle. Each time you press the button, the pitch angle increases by 5 °.
【Pause】Click the button, the propeller stops working, the default is off.
【Home】Press power button for 3-5 seconds, and the remote controller turns on.

18
【High-angle shoot】Set the pitch angle of 0 °~-45 °, the smaller the number, the
larger the angle. Each time you press the button, the pitch angle increases by 5 °.
【Pair button for phone】used to pair with the smart phone. (The mobile phone
needs to turn on the Bluetooth function in advance).
【Speed down】Press the button once to shift into lower gear.
【Speed up】Press the button once to shift into higher gear.
【Charging indicator】Displays the light status when the remote is charging.
【Left/Right Joystick】Control the movement of the drone, consistent with the
joystick setting in the mobile APP.
【Brightness reduction】Manually reduce the brightness of the light, and tap the
button once to reduce the brightness.
【Brightness enhancement】Manually increase the brightness of the light, and
click the button once to increase the brightness.
【Zoom in】Enlarge the image.
【Zoom out】Reduce the image.
【Photo】Tap the photo buttons to take photos.
【Record】Click the button to start recording; click it again to stop recording.
【Open】Long press, the mechanical arm will open continuously; release the
botton, the mechanical arm will pause to open.
【Close】Long press, the mechanical arm closes continuously; release the
button, mechanical arm closes temporarily.
Connect the USB charging cable to the
charging port of the remote control, the
charging indicator lights up red and flashes
slowly, to start charging; the charging indicator
lights all light up red and stop flashing,
indicating that the remote is fully charged.
Charging for the Remote Controller
Charging interface