YOW! CraftY Cutter User manual

Quick Start Guide
The blade tip recommends leaking a length of about 0.2 mm,
but new users tend to use too longer blade tip.
Our idea is to cut only the surface of the sticker,
but leaving only the minimum scratches under the bottom.
This way you can easily tear off the adhesive. If you can't cut
through a small corner or some small details, you can
increase the length of the blade.
The recommended speed setting is 600 mm / s
The blade force setting 10 - 20.
1. Verify the Package Contents
Power
cable port
Blade carriage
(Built-in Camera)
Touch screen
control panel
Set the blade tip to
only the surface of
the material without
cutting the bottom layer
Blade holder 1 pcs
60 degree blade 1 pcs
45 degree blade 2pcs
Pen tool 1 pcs
USB Cable 1 pcs
Cutting Mat 1 pcs
Power adaptor 1 set
2. Note the Names of Parts
U-disk
interface
USB
cable
port
Blade holder seat:
Tightener for Locking
Blade Holder
Power button:
Click for power on,
Hold on 3 seconds for power off.
Pinch wheels assembly lever：
Up for pressing material, down
for release material
Pinch wheels assembly
pressure lever：
Up for higher force pressing,
down for normal force.
3. Blade installing instruction
The most commonly used 45-degree case (red cap)
Thin material uses a 60-degree knee (blue cap)
4. Blade tip and blade force / speed value recommended settings
1) Press the silver
button to eject the blade
3)The tip length can be adjusted by turning the gold knob
counterclockwise
5)Turn the gold knob clockwise to fix the tip length
4)Adjust the length of
the tip of the tool holder
by turning the silver knob
2) The blade can be inserted
here, be careful that the tip
of the blade can easily hurt you.
5. Place material
Step 1. Pull down the pinch wheels
assembly lever.
Step 2. Move the pinch wheel assembly again the steel axis.
Step 3. Load the material, at least 2 pcs pinch wheels pressing the material.
Step 4. Pull up the pinch wheels assembly lever, make sure material holding well.
Step 5. The blade is the origin point for cutting, move the blade carriage to specify
position and then start cutting.
Step 6. If it is print and cut job, need to move the blade tip around 3mm close to the
first mark.
First Mark

6. DrawCut Installation
1
2
3
7.DrawCut License Deactivation
Input email address twice to
register software PSN
If PC system crashed or need to change a
PC to run the software, how to do?
1.Deactivate license on previous PC
2.Activate license on new PC
Input Product Serial Number(PSN)_
Select your Cutter Model
8.Connection Settings
1.Vinyl Spooler — Connection Tap
2.Set Connection Method Port Type
“Direct USB Port” for USB Cable connection
3.Set Connection Method Port Type
“Windows Port” and choose U_disk for
exporting PLT file onto a USB flash drive
and then loading plt file using the control
panel on the cutter.
9.Send to Cut
1.Click to send artwork to cut directly
1.Click “Create Cut Contour”to add cutting line simply
2.Click “Contour Cut Wizard” to add L-Shape mark for print and cut
10.Simple Print and Cut Process
1Import raster images and Click
Create Cut Contour to trace outline
2Get a preliminary trace after settings
3Print the project, after selecting registration L-Shape mark
properties, location of project on the page, and printer options.
4Place the material and move the blade tip close to the L-Shape
mark(in 3mm is ok), camera will find the reg mark.
5
Go to software and send to cut. Cutter will scan reg mark for
contour cutting automatically. If the not finding reg mark, click the
cross of reg mark on LCD control panel and then click ok, we can help
the cutter find the reg mark easily.