Z-EDGE ZAI03 User manual
PORTABLE AIR INFLATOR
& POWER BANK
Please be sure to read this manual carefully before use.
ZAI03
USER GUIDE
Please read this instruction carefully before using this product for the
first time. It will guide you to use it correctly and remind you of the
relevant precautions.
This product is a portable smart air inflator & power bank, suitable
for the inflation of small cars tire, motorcycle tire, bicycle tire, balls
swimming ring and other inflatables.
When using this product to inflate, please notice the correct air pressure
value required by the product need to be inflated. The product and
hose will get hot after prolonged use. Children are not allowed to use
or play with it.
1
SAFETY INFORMATION
ACCESSORIES LIST
A
D E F G
B C
A. (1) Storage Bag
B. (1) ZAI03
C. (1) Hose
D. (1) Type-C Charging Cable
E. (1) Presta Valve Adapter
F. (1) Ball Needle Adapter
G. (1) Plastic Nozzle Adapter
Tip:
The illustrations of products,
accessories, user interface, etc.
in the manual are schematic
diagrams, for reference only,
please refer to the actual
product.
1
10
9
11
12
13
14
15
2
3
4
6
7
8
5
2
PRODUCT OVERVIEW
Exhaust
Hose Connection
Type-C Port (Input)
USB Charging Port (Output)
LED Light
Display Screen
Control Button
Power Button
1
2
3
4
5
6
7
8
Digital Display
Battery Indicator
Unit of Measurement
Process Bar
Preset Pressure
Scene Modes
Inlet
9
10
11
12
13
14
15
CONTROL BUTTON
3
U/LED
+
-
SET
Press
Switch unit of measurement
Press & Hold (3 Seconds):
Turn on/off LED light
Press
Activate air inflator
Press & Hold (3 Seconds):
Power ZAI03 on/off
Press
Increase 1 PSI / BAR / KPA
Press & Hold (3 Seconds):
Continual increase until released
Press
Decrease 1 PSI / BAR / KPA
Press & Hold (3 Seconds):
Continual decrease until released
Press
Switch scene modes
ADAPTER COMPATIBILITY
4
Suitable for
Cars, Trucks, Trailers, Motorcycle, Tires & more
Just connect it directly.
Schrader Valve (On the hose[C])
Suitable for
Bicycle Tires
Presta Valve
Suitable for
Basketballs, Soccer, Balls, Footballs,
Volleyballs, etc
Ball Needle
Suitable for
Pool Tubes, Floats, Balloons, Toys, etc.
Plastic Nozzle
The connection of the hose is shown in the following figure:
HOW TO USE
5
1. Charging
Use the Type-C charging cable to connect the air pump and the
adapter(Not Included) for charging.
Charging status: the battery indicator flashes
Full status: battery indicator is green, and does not flash.
Caution:
The product cannot be used during charging.
Battery Status 100%
Battery Status 60%
Battery Status 30%
Battery Status 5%
2. Power On/Off
Power On Power Off
Press the power button for 3
seconds to power on.
Press the power button for 3
seconds to power off.
Note:
Z-EDGE ZAI03 will automatically turn off after 3 minutes of inactivity.
6
+
U/LED
-
5. Preset pressure value
Press "+" "-" button: Adjust the preset pressure value.
Long press "+" "-" button: can quickly adjust the preset
pressure value.
Note:
The scene switch and preset pressure value are automatically saved by
the programm. You only need to switch the scene for the next use, and
the preset pressure is automatically set.
Press "SET" button to switch between the following five inflation scenarios.
Select the correct inflation scene before inflation.
Refer the default settings (below).
Car 35 2.4
40 2.7
38 2.6
80.5
0~150 0~10
0-65 PSI
0-55 PSI
0-100 PSI
0-15 PSI
0-100 PSI
Motorcycle
Bike
Ball
Customize
1PSI=6.89KPA 1BAR=100KPA 1kg/cm2=98KPA
3. Mode Switching
Press "U/LED" button to switch key, you can switch the air pressure display
unit. The unit conversion formula is shown below:
4. Unit Switching
Note:
Z-EDGE ZAI03 will automatically turn off after 3 minutes of inactivity.
MODE PSI BAR Range
Long press the button to turn on/off LED lighting.
6. Using The LED Light
7
7. Using The Air Inflator
Start to Inflate
Press the "Power Button"[8] to start inflation.
The digital display of the real-time air pressure value[9] changes
during inflation.
It will generate 75-80 dB noise during inflation and the
hose produces high temperature during long-term work.
Avoid prolonged contact with hose and hose joints[2] by hand.
Special Reminder
*Press the Power button to manually turn off the air compressor at any time.
The inflation pressure of items such as balloons, toy balls, swimming rings
and other products is lower than the range of this air pump, and the
inflation cannot be automatically stopped by the preset pressure.
8. Using The Power Bank
1. Use a compatible USB charging cable(Not included) to charge your
device via the USB output port.
2. Press the "Power Button"[8] to power on the ZAI03. The device
will begin to charge.
*When the power bank battery is low or your device is fully charged,
the inflator will shut down.
Press "SET" button to switch between the following five inflation scenarios.
Select the correct inflation scene before inflation.
Refer the default settings (below).
Note:
1. Always refer to the manufacturer's recommended PSI/BAR level for
the item being inflated
8
9. Measuring Pressure
After switching on, connect the air pipe to the measured object, and the
measured pressure value[9] shows the current pressure value.
10. Reset
After switching on, when the measured pressure value is not zero, long
press "U/LED" and "SET"key for 3 seconds to enter automatically reset.
Attention
- When the hose is unscrewed, the hose and the joint will produce high
temperature due to long time work.
- Do not touch it after a long working time.
- It is recommended to allow the device to cool down for a few minutes.
Note:
Products whose pressure are below the inflator's mininum range,
such as alloons, swimming rings, and ball for kids,cannot be measured
pressure.
9
SPECIFICATION
Model:
Battery Capacity:
Inflation Pressure:
Charging Input:
USB Output:
Charging Time:
Dimension:
Weight:
Working Temperature:
ZAI03
2000mAh / 14.8Wh
150PSI(Max.)
Type-C 5V / 2A
5V / 1.5A
±3H
6x2.3x1.5inch / 152x60x38mm
0.85LB / 385g
14-113°F / -10-45°C
Common unit conversion: 1BAR = 14.5PSI, 1BAR = 100KPA.
10
NOTES
· Before inflating, please confirm the air pressure value required by the
item need to be inflated to avoid injury caused by over-inflation bursting.
· The product has a built-in non-removable lithium battery. Please do
not throw the product into fire or discard it carelessly. The lithium
battery may cause fire, spontaneous combustion or explosion due to
overheating, impact and water ingress.
Please avoid putting it in a high temperature environment such as a
car that can be exposed to direct sunlight;
· Do not bend or step on the inflation tube during inflation to keep the
air flow smooth;
· When the air pump is working, the operator should not leave the scene,
pay attention to observe at any time to prevent the air pressure from
being too high due to unpreset air pressure;
· The machine should avoid moisture, heavy falls, water immersion and
mud or sand intrusion;
· There is a DC motor in the air pump, which may generate electric sparks
during operation.So do not put it near flammable liquids or gases
when it is working.
· The storage temperature of the product should not be lower than -10 °C
or higher than 45 ° C. Excessive heat or cold will shorten the product
life and damage the built-in battery.
· The battery may be damaged if left idle for a long time. It is recommended
to charge it at least once every three months.
· This product is not a toy, it is forbidden for children to use; keep a safe
distance from children when inflating objects.
· Before setting the inflation pressure value, please make sure that you
have selected the correct measurement unit, otherwise it may lead to
dangers such as high air pressure;
11
TROUBLESHOOTING
Malfunction Solution
Slow Inflation
1. Check whether the power is sufficient.
2. Check if the air hose is leaking.
3. Check whether the connection parts at both
ends of the air hose are tight.
Can not inflate
when turning on
1. Check whether the air hose is pulled out, you
need to pull out the hose to start inflation.
2. Check whether the power is sufficient.
3. Check whether the current tire pressure value
is higher than the preset value.
Cannot increase or
decrease the preset
pressure
1. Check whether you are in an incorrect
scenario mode.
2. Select the free mode without any icon lit, and
the preset value can be adjusted within the
range of 3-150psi.
Normal inflation but
screen shows 0
Balloons and other low-pressure inflatable
products are not within the measurable range
of the device
The air pump has shut
down automatically
after screwing the valve
adapter
Long press "Start-stop button" to turn on again.
Air leakage when
connecting the hose Tighten the hose
Wrong display Please press "U/LED" and "SET"key at the
same time to restore the inflator.
· Before inflating, please confirm the air pressure value required by the
item need to be inflated to avoid injury caused by over-inflation bursting.
· The product has a built-in non-removable lithium battery. Please do
not throw the product into fire or discard it carelessly. The lithium
battery may cause fire, spontaneous combustion or explosion due to
overheating, impact and water ingress.
Please avoid putting it in a high temperature environment such as a
car that can be exposed to direct sunlight;
· Do not bend or step on the inflation tube during inflation to keep the
air flow smooth;
· When the air pump is working, the operator should not leave the scene,
pay attention to observe at any time to prevent the air pressure from
being too high due to unpreset air pressure;
· The machine should avoid moisture, heavy falls, water immersion and
mud or sand intrusion;
· There is a DC motor in the air pump, which may generate electric sparks
during operation.So do not put it near flammable liquids or gases
when it is working.
· The storage temperature of the product should not be lower than -10 °C
or higher than 45 ° C. Excessive heat or cold will shorten the product
life and damage the built-in battery.
· The battery may be damaged if left idle for a long time. It is recommended
to charge it at least once every three months.
· This product is not a toy, it is forbidden for children to use; keep a safe
distance from children when inflating objects.
· Before setting the inflation pressure value, please make sure that you
have selected the correct measurement unit, otherwise it may lead to
dangers such as high air pressure;
12
FCC STATEMENT
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Its operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may
cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.
13
For customer support inquiries please contact:
Zeroedge Technology owns the copyright for this manual.
The contents of this manual are subject to change without notice to
improve quality.
CUSTOMER SUPPORT
Follow us to get the latest updates.
@zeroedgeGA @zeroedgeGA
@zeroedgeGA @zeroedge
[email protected](EU/Other)
www.z-edge.com
14
Thank you for choosing Z-EDGE.
Your satisfaction is always our first priority.
All Z-EDGE customers have a 30-day money back guarantee,
to make sure your shopping experience is worry-free.
By default, the unit warranty-period is set to 12 months
from the unit-shipped date.
You can be corrected to 18 months by registering your order
and product in our official website
within 30 days of receiving the product.
Product Registration URL:
www.z-edge.com/pages/register
WARRANTY
ZAI03Z23UMEN-01
To view the complete user manual,
please visit:
Table of contents
