Z-Wave EH-DS-01 User manual

Specification
EH-DS-01 Door/Window Sensor Installation Guide
Introduction
Z-Wave Door/Window sensors are designed to secure the perimeter of the residential premise, and provide the
ability to add various automation services. The Z-Wave Door/Window sensor, which consists of a magnet that
attaches to a door or window, will communicate door events to the home security system. When the magnet is
moved away from the sensor, a signal will be sent to the control panel that communicates the changed state to the
security system. Signals can also be used to activate a chime or convenience lighting based on system settings.
Add (Inclusion) Sensor
For Adding in (Inclusion) a network: Put the Z-Wave Interface Controller into “Add (Inclusion)” mode, and
following its instruction to add EH-DS-01 to your controller. This Door/Window sensor needs to be included
before installation.
1. Open the device . (Figure 1)
Figure 1
2. Pressing the function button three times.
CR123A BatteryFunction Button
Figure 2
3. Red led will blink three times while inclussion the network successful (Figure 2).
Red LED Indictor
Figure 3
4. If inclussion failed, the sensor will go into sleep mode. To wake the sensor again, you
need to use magnet or tamper (Figure 3) to trigger a Adding (Inclusion) process, and then sensor will repeat
steps from 3 to 4.
Frequency
908.42 /908.40 /916.00 MHz
Battery Type
CR123ABattery 1PCS
Operating Temperature
Cto 50 C(32°F -122°F)
Storage Temperature
Cto 60 C(-4°F -140°F)
Operating Air Range
Up to 148 feet line of sight
Dimension
Device: 94.5 mm x24.3 mm x22.4 mm
Magnet: 46 mm x12.8 mm x13.3 mm

Remove (Exclusion) Sensor
Inclusion Sensor
For Removing from (Exclusion) a network: Put the Z-Wave Interface Controller into “Remove (Exclusion)” mode,
and following its instruction to delete EH-DS-01 to your Z-Wave controller.
1. Open the device and pressing the function three timesand enter exclusion mode. (Figure 4).
Pressing the funcation button
Figure 4
2. If remove (exclusion) successful, go auto Adding procedure.
3. Node ID has been remove.
Factory Default Reset
Installation
Pressing the function button while installing battary.
Note: Use this procedure only in the event that the primary controller is lost.
Installation
Inclusion Sensor
1. Please make sure that the sensor and magnet is located less than 0.7 inch from each other. For optimal
performance, it is highly recommended to install the Door/Window sensor on the fixed frame and the magnet
on the moving part of the door/window. Place the sensor near the top of the door that close to the opening
edge of the door. This is the mounting location for the sensor.
2. Use the provided double-sided tape on the sensor. Attach the sensor to the door. Press firmly and hold in place
for a few seconds (Figure 5). Secure it with silicone if needed.
Figure 5
Adhesive application surface: Acrylic, Glass
Aluminum and Stainless steel…etc.
3. Use provided double-sided tape on the magnet. Make sure the alignment of both sensor and magnet alignment
mark are facing each other (Figure 6). Press firmly and hold in place for a few seconds. Secure it with
silicone if needed.

Alignment Mark
Figure 6
4. EH-DS-01 can be included and operated in any Z-Wave network with other Z-Wave certified devices
from other manufacturers and/or other applications. All non-battery operated nodes within the network will
act as repeaters regardless of vendor to increase reliability of the network.
5. Association
Support grouping identifier = 1
Support one group with 5 nodes.
All triggering report and low voltage report will be sent to the associated nodes.
Z-Wave Command Classes
• COMMAND_CLASS_ZWAVEPLUS_INFO
• COMMAND_CLASS_VERSION
• COMMAND_CLASS_MANUFACTURER_SPECIFIC
• COMMAND_CLASS_DEVICE_RESET_LOCALLY
• COMMAND_CLASS_POWERLEVEL
• COMMAND_CLASS_BATTERY
• COMMAND_CLASS_NOTIFICATION
• COMMAND_CLASS_ASSOCIATION
• COMMAND_CLASS_ASSOCIATION_GRP_INFO
• COMMAND_CLASS_SENSOR_BINARY
• COMMAND_CLASS_WAKE_UP

Notification Type
Operation
1. The LED will stay off during the normal operation.
2. The sensor is equipped with a tamper switch. If the cover of sensor is removed, the sensor will send an alarm
to the home controller.
3.Tamper switch event will be ignored when in auto inclusion procedure.
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be received, including interference that may cause undesired
operation.
Changes or modifications not expressly approved by the Resolution Products, Inc. could void the user's authority to
operate this equipment.
FCC ID: 2AIPTEHDS01
Switch Type
Status
Notification Type
Reed Switch
0x06
Tamper Switch
0x07
Event
Reed Switch
Close:0x17, Open:0x16
Tamper Switch
Close:0x00, Open:0x03
Sensor Binary Report
Reed Switch
Close:0x00, Open:0xFF