Zaor Miza 49 Flex User manual

Miza 49 Flex

Unpack the parts carefully and set up so that you can see the part numbers clearly. In the big
box you should find a small cardboard box with all the screws and bolts for assembly.
Here you have an exploded view of the whole desk and how it is supposed to come together.
We use high quality furniture assembly components from renowned EU manufacturers.
Please, never use force. These parts should come together easily, in case of doubt check the
manual again or contact support.
The assembly of your desk uses special kits.
Here's how to use them
1) On the piece with the threaded
insert(s) , put in the system bolt(s)
and tighten making sure to align the
hole in the system bolt at a 90º angle.
Please note that the system bolt may have
a little slack in this position, which is fine!
2) Ensure that the hole in the bolt
aligns with the opening in the other
piece to be able to put in the safety
screw.
3) In each hole in the second piece, put
in a cone shaped safety screw and
tighten with a cross screw driver -
without forcing.
The 2 parts will now be safely
attached.
Thanks for choosing a piece of furniture from Zaor. Before you can enjoy
the use of it you need to build it. We tried to put all the explanations
necessary for a safe build, when in doubt please get in touch or check out
our Youtube channel where we are putting more and more assembly
videos to help you with this important task. Enjoy!
General technique for putting together Zaor desks
A
A1
B1
B
C
D
EF
G
I
J
H
K
L
M

Left
Type F
A
B
STEP 2STEP 1
Slider 1 (L) Slider 2 (L)

Right
STEP 4STEP 3
Slider 1 (R)Slider 2 (R)
Slider 1 TYPE I
1st 20 mm
2nd 40 mm
3rd 60 mm
4th 80mm
5th 100 mm
6th 120 mm
6 heights
Type S2
A / B
1
st
2
nd
3
rh
4
th
5
th
6
th
Choose Height

Push wooden dowels type W in the appropriate holes
C
STEP 6
A / B
A1 / B1
D
A1 / B1
Slider 2 Type S2
STEP 5

F
G
E
I
J
Type F

L
M
K

L
M
C
D
Join panels C and D. Attach, using the
system bolts that you mount on the
threaded inserts in panel n°C. Adjust so
they are pointing such that
holes can be seen when inserted into
panel n°D (no need to tighten them).
Use the small slanted screws to
tighten the connection between the
two panels. Proceed likewise for the
other connections. D
C
Use screws Type Rb L
STEP 7 STEP 8

K
M
A
KM
Use screws Type Rs
STEP 9 STEP 10

D
C
A
B
Use screws Type Rs
STEP 12
E
F
STEP 11

G
I
J
A1
J
G
I
B1
Use screws Type K
J
STEP 13 STEP 14

H
PACKING LIST:
TOOLS:
Suggested
*
*
m6x30 mm
Type K
x04
Rack rail
Type R
x4
Assembly Kits
x38 Type W
Wooden dowels
x42
35 mm
Plastic insert
Type I
x36
Sliders
Type SL
x02
3.5x16 mm
Type S2
x12
Hex wrench
Type H
x1
Rack rail screws
Type Rs
x04
Rack bolt screws
Type Rb
x2
Rack units screws
Type Ru
x24
Plastic foot
Type F
x4
STEP 15