Zavio D4210 User manual

1

PN: 86085A2000010

D4210

1

Zavio D4210 Quick Installation Guide

Please follow the installation steps below to set up D4210 IR Dome IP Camera.

Check the package contents against the list below. See P.1

Physical overview. See P.2

I/O Terminal Block Circuit. See P.3

I/O Terminal Block Pin Definition. See P.3

LED Indicator Definition. See P.4

Power mode. See P.4

Install the hardware and connect all cables. See P.4

Microsoft OS: Use the software CD to install Intelligent IP Installer. See P.7

Access the IP Camera using Intelligent IP Installer. See P.8

Mac OS using Safari Browser. See P.10

Change light environment setting. See P.11

Change the Web Interface into your preferred language. See P.11

Application of IP Camera. See P.12

For more information, please check the User Manual available in the Software CD or you can download the latest

software from http://www.zavio.com

Package Contents

Note:

Power Adapter is supplied by user. 2pin I/O terminal block is for DC 12V Power Adapter used.

Camera

D4210 IR Dome IP Camera

Quick Installation Guide

Brief product information and quick installation

Software CD

IP Surveillance Software

Intelligent IP Installer

User Manuals

Language Packs

Accessory

6 pin terminal cable for DI/DO and audio

Screw pack for wall and ceiling mounting ( 2 screws, 2 plastic wall anchors )

Alignment sticker

Cat 5e Female Coupler

L-type Hex Key Wrench

2pin I/O terminal block

Focus Adjustment

2

Physical overview

Built-in Microphone

Ethernet / PoE

Dome bubble

Slide cover

Top cover

Leave the slide cover if you would like to plug in cables through

the side of top cover and through a hole on the ceiling or wall.

Routing hole

Lens

MicroSD/SDHC

Reset

Power LED Indicator

Network LED Indicator

External I/O connector

DC 12V/1A

Internal microphone

Light Sensor

IR LEDs (12units,

Distance 10m)

Open the shell alerts

Ethernet 10/100 RJ45 Plug

3

I/O Terminal Block Circuit

I/O Terminal Block Pin Definition

This Camera provides an external I/O terminal block which is used to connect input/ output devices.

The pin definitions are described below.

Definition

Description

Max. V/A

1

Ground

-

2

+ 12V DC

12V DC

1.2W

3

Audio Input

Connect the wires of the audio input device to GND (Pin 1) and

AUDIO.IN (Pin 3).

-

4

Audio Output

Connect the wires of the audio output device to GND (Pin 1) and

AUDIO.OUT (Pin 4).

-

5

Digital Output 1

Uses an NPN transistor with the emitter connected to the GND

pin. If used with an external relay, a diode must be connected in

parallel with the load for protection against voltage transients.

100 mA

24V

6

Digital Input 1

Connected to GND to activate, or leave floating (or unconnected)

to deactivate.

30V DC

4

LED Indicator Definition

LED

Color

Indication

Network

Blue

Flash blue while Network activity.

Power

Red

Steady red for booting up process

Blue

Steady blue for booting up completion

Purple

Flash purple during firmware upgrading; when reset button pressed for at least 5 sec.

to factory default

Unlit

When you press reset button; or Power off

Reset: When the device is empowered, press the Reset Button to reboot the device, or hold the Reset Button for

10 seconds to the settings back to factory default.

Reset process: Press reset button until indicator Unlitsteady red (booting up process)steady blue (booting up

completion)

Reset to default process: Press until indicator steady bluesteady red (booting up process)steady blue (booting

up completion)

Power Mode

PoE Mode

Power

Requirement

PoE (IEEE802.3af) with Class 3

Power

Consumption

4.19W

Adaptor Mode

Power

Requirement

12V/1A Adaptor

Power

Consumption

4.24W

Install the hardware and connect all cables

a. Hardware Installing

1) Loosen the tamper-proof screws using supplied L-type Hex Key Wrench

2) Remove the dome cover. Be careful do not scratch the cover glass.

3) Remove the slide cover if you want to route cable from the side of camera instead of routing hold.

b. Wall mounting and Ceiling mounting

1) Attached the alignment sticker to the wall/ceiling. Drill three holes into the wall, which two for screws and one

for cable (if you want to route cables through routing hole).

2) Hammer the supplied plastic anchors into the holes.

3) Align the two holes on the base of camera with the two plastic anchors on the wall or ceiling, insert the supplied

screws to the corresponding hole and screw them.

4) Adjust the angle of camera to aim the shooting area.

(for F3105)

5

c. Connect all cables

c1. Without Power over Ethernet (PoE) connection

1. Connect the power adaptor to the IP Camera.

2. Connect the IP Camera to a normal Hub / Switch / Router.

c2. Power over Ethernet (PoE)

1. Connect the IP Camera to a PoE-enabled Hub / Switch / Router.

Note:

If using a non-PoE switch, please use a PoE power injector to connect

the camera.

6

d. To adjust the view angle- 3 axis Mechanism Design

1. Turn the lens module right and left to your desired pan position.

2. Turn the lens module up and down to your desire tile position.

3. Turn the lens module to adjust the image orientation to satisfied angle.

Important:

Do not rotate the IR LEDs so that it gets blocked by the housing as it will affect the IR performance

(as shown below). If the image is upside down, please use the image rotate function in Video Setting.

7

e. Completion

1. Clean the dome bubble to remove the dust and finger print.

2. Fix the tamper-proof screws using supplied special hex. Be careful do not scratch the cover glass.

3. The installation is complete now.

Microsoft OS: Use the software CD to install Intelligent IP Installer

Power on your PC and insert the CD-ROM. The setup page will show up automatically. Please follow these steps to

install the firmware.

Select “Intelligent IPInstaller”and follow the installation process to complete the installation.

8

Access the IP Camera using Intelligent IP Installer

1. Please check two settings before using Intelligent IP Installer .

2

a. Browser’s Internet Properties → Security

→ Default Level

b. Browser’s Internet Properties → Privacy

→ Uncheck Pop-up Blocker

2. Click the Intelligent IP Installer Icon on your desktop. The main page will show up listing all active

camera and video server devices. Select the relevant IP camera from the list and click Link to IE.

3. Enter your Username and Password

to login to the IP Camera.

(Default is admin / admin)

9

4. When accessing the IP Camera for the first time, a yellow information bar appears below the address bar:

This website wants to install the following add-on: ‘AxvideoView.cab from ‘Zavio Inc’.

5. Click the information bar, and select Install ActiveX control.

6. Click Install.

7. Live video displays in the centre of your web browser.

10

Mac OS using Safari Browser

1. Select Safari icon

2. Click Bonjour function and select the camera

you wish to access.

3. Enter name and password to login to the IP

camera. (Default is admin / admin)

4. The monitor image will be displayed in your browser.

11

Lighting environment setting

The default setting of lighting environment is Auto. However, you may also select 50 or 60 Hz upon the lighting

environment of your country.

Go to “Setting > Live View > Camera Setting > Image Setting”, select the environment setting you wish.

Change the Web Interface into your preferred language

Use the settings screen to set the language of the Web Interface.

Go to “System > Maintenance > Language”.

1. Insert Software CD into your CD-ROM.

2. Browse and select the preferred language from language pack in the Software CD and then click OK.

3. The web interface will change into your preferred language.

12

Application of IP Camera

13

Memo

…………………………………………………………………………………..

14

Zavio D4210 User manual

Popular Security Camera manuals by other brands