Zavio CD3210 User manual

0
/ B5210
Eyeball Dome IP Camera
Quick Installation Guide

1
Quick Installation Guide
Please follow the installation steps below to set up your IP Camera.
Check the package contents with the list below. See P.1
Physical Overview. See P.2
I/O Terminal Block Circuit. & I/O Terminal Block Pin Definition. See P.3
Installation of hardware and connection of all cables. See P.4~P.6
MAC OS: using Safari Browser. See P.6
Z Plus. See P.7~P.9
Lighting environment.& Change the Web Interface into your preferred language
See P.10
Package Contents
Camera
IP Camera
Quick Installation Guide
Brief product information and quick installation
Accessory
Alignment Sticker
Screw pack for wall and ceiling mounting
Waterproof connector
Terminal block 2 pin DC connector
Software
The following software and information are available online:
-Video Management Software
-Z PLUS
-User manuals
-Camera Language Packs
You may download the above at http://www.zavio.com/downloads.php or you
may scan the below QR-Code.
To activate Video Management Software, please enter the license key below.

2
Physical Overview
CD3210
CD3211
IR LED
Light sensor
IR LED
Light sensor

3
I/O Terminal Block Circuit
Note: Please use the supplied waterproof RJ45 connector and seal all connectors tightly to avoid moisture.
I/O Terminal Block Pin Definition
Pin Color
Definition
Description
Max. V/A
Green & White
Audio In
Connect the wires of the audio input device to GND
(White) and AUDIO LINE IN (Green).
-
White+Green
Orange+Black
Audio Out
Connect the wires of the audio output device to GND
(Orange+Black) and AUDIO LINE OUT (White+Green).
-
Purple & Black
Alarm In 1
Connect to GND to activate, or leave floating (or
unconnected) to deactivate.
5V DC / 50mA
Red & Black
Alarm In 2
Connect to GND to activate, or leave floating (or
unconnected) to deactivate.
5V DC / 50mA
Yellow +
Black & Green
Alarm Out
Relay contact output. Contact capacity with resistance
load.
0.3A at 125V AC
or 1A at 30V DC
Brown + Pink
RS-485
-
-

4
Reset: When the device is powered, press the Reset Button to reboot the device,
or hold the Reset Button for 15 seconds to the settings back to factory default.
Install the hardware and connect all cables
A. RJ45 waterproof connector
1. Make sure all components are assembled as shown on the below graph.
2. Check that the Ethernet Port and the Waterproof main body are tightly fasten.
B. Disassemble eyeball dome camera
Twist the outer housing counterclockwise and then remove the outer housing
from the camera base. (see below pictures)
①②③
C. Wall mounting and Ceiling mounting
a. Attach the alignment sticker to the wall/ceiling. Drill four holes into the
wall/ceiling. Hammer the supplied plastic anchors into the screw holes.
b. Place the camera base on the wall/ceiling, pass the cables of the cameras
through the base, and screw the base with the supplied four screws. (see
picture 4)
c. Adjust the camera angle and twist back the outer housing
simultaneously.
d. Optionally screw back the set screws to the outer housing by using the
supplied hex wrench to prevent uninstallation.

5
D.Junction box AZ-J01 (optional accessory)
1. Self-adhesive sticker
2. Cable tie
3. Connection plate
4. Stopper
5. Wall screws
6. Foam pad
7. Round head screws
E. Connect all cables
E1. Without Power over Ethernet (PoE) connection
1. Connect the power adaptor to the IP Camera.
2. Use a standard RJ-45 network cable and connect the IP Camera to a
hub/switch/router.
E2. Power over Ethernet (PoE)
1. Use a standard RJ-45 network cable and connect the IP Camera to a
PoE-enabled hub/switch/router.

6
MAC OS using Safari Browser
1. Select Safari Icon
2. Click Bonjour function and select the camera you wish to access.
3. Enter name and password to login to the IP camera
(Default is admin / admin)

7
4. Live video will display in the center of your web browser
Z Plus
A. Get the image of camera with Z Plus.
1. Download Z Plus from ZAVIO official website..
2. Follow the instruction and install Z Plus.
3. Enter name and password to login to the IP
camera. (Default is admin / admin)

8
3. Click the icon and get into the software.

9
B. Camera setting

10
Lighting environment setting
Default setting for lighting environment is Auto. You may change exposure
frequency to 50 or 60 Hz at Setting > Live View > Camera Setting > Image
Setting.
Change the Web Interface into your preferred language
Before accessing the Setting page to change the language of the web interface,
you must download the language pack.
1. Go to http://www.zavio.com/downloads.php and download the language pack
corresponding to your IP camera model.
2. Go to the IP camera setting page and upload the preferred language from the
language pack downloaded from step 1.
Setting > System > Maintenance > Language > Upload
3. Once the upload is complete, the browser will automatically change the
language.