ZCS AZZURRO CONNEXT User manual

Identification: MD-AL-GI-00 Rev. 1.2 of 24/06/21 - Application: GID
Zucchetti Centro Sistemi S.p.A. - Green Innovation Division
Via Lungarno, 248 - 52028 Terranuova Bracciolini - Arezzo, Italy
tel. [phone] - fax. [phone]
[e-mail] - [email protected] - zcsazzurro.com
Pile Reg. IT12110P00002965 - Share Capital € 100,000.00 fully paid up
AR Company Reg. no. 03225010481 - REA AR no. 94189
ISO 9001 Certified Company - Certificate no. 9151 - CNS0 - IT-17778
“Connext System User Manual” of 10/01/2023 Rev. 2.2
“CONNEXT” Control System
User Manual

Solo documento principale.
2/67
Identification: MD-AL-GI-00
Rev. 1.2 07.06.21 - Application: GID
Connext User Manual
Rev. 2.2 10/01/2023
General instructions
This manual contains important safety instructions that must be followed during installation and
maintenance of the equipment.
Please keep these instructions!
This manual must be considered an integral part of the equipment, and must be available at all times
to everyone who interacts with the equipment. The manual must always accompany the equipment,
even when it is transferred to another user or plant.
Copyright statement
The copyright of this manual belongs to Zucchetti Centro Sistemi S.p.A. No part of this manual
(including the software, etc.) may be copied, reproduced or distributed in any form or by any means
without the permission of Zucchetti Centro Sistemi S.p.A. All rights reserved. ZCS reserves the right
to final interpretation. This manual is subject to change based on feedback from users, installers or
customers. Please check our website http://www.zcsazzurro.com for the latest version.
Technical support
ZCS offers full technical support and advice which can be accessed by making a direct request
through the website www.zcsazzurro.com
The toll-free number for Italy is: 800 72 74 64.

Solo documento principale.
3/67
Identification: MD-AL-GI-00
Rev. 1.2 07.06.21 - Application: GID
Connext User Manual
Rev. 2.2 10/01/2023
Summary
1. Preliminary safety instructions ..............................................................................................................................7
1.1. Safety instructions...............................................................................................................................................7
1.2. Symbols and icons...............................................................................................................................................9
2. Product features ........................................................................................................................................................ 11
2.1. Product presentation ...................................................................................................................................... 11
2.2. Product overview ............................................................................................................................................. 12
3. Installation................................................................................................................................................................... 15
3.1. Checks before installation............................................................................................................................. 15
3.2. Installation process.......................................................................................................................................... 17
3.3. Materials and cables........................................................................................................................................ 17
3.4. Electrical connections..................................................................................................................................... 18
3.5. Connecting AC power cables........................................................................................................................ 18
4. Connecting to Azzurro EV charging stations .................................................................................................. 20
5. Systems with ZCS Azzurro inverter.................................................................................................................... 23
5.1. Configuration 1 –System with Azzurro single-phase hybrid inverter........................................ 23
5.2. Configuration 2 –System with Azzurro 3000SP inverter................................................................. 26
5.3. Configuration 3 –System with Azzurro three-phase hybrid inverter ......................................... 28
5.4. Configuration 4 –System with Azzurro single-phase photovoltaic inverter............................ 30
5.5. Configuration 5 –System with Azzurro three-phase photovoltaic inverter ............................. 33
6. Systems without ZCS Azzurro inverter............................................................................................................. 35
6.1. Configuration 6 –System with single-phase photovoltaic production ....................................... 35
6.2. Configuration 7 –System with three-phase photovoltaic production......................................... 37
6.3. Configuration 8 –Single-phase system without photovoltaic production................................. 40
6.4. Configuration 9 –Three-phase system without photovoltaic production................................. 41
7. Initial system configuration .................................................................................................................................. 43
7.1. Creating an account on the Azzurro Systems app................................................................................ 43
7.2. Adding an Azzurro inverter.......................................................................................................................... 47
7.3. Adding measuring systems........................................................................................................................... 48
7.4. Adding and managing wallboxes................................................................................................................ 49

Solo documento principale.
4/67
Identification: MD-AL-GI-00
Rev. 1.2 07.06.21 - Application: GID
Connext User Manual
Rev. 2.2 10/01/2023
8. Dry contact management ....................................................................................................................................... 53
8.1. Setting dry contacts from app...................................................................................................................... 53
9. Access for maintenance only................................................................................................................................. 56
9.1. Access connection for maintenance only ................................................................................................ 56
10. Technical datasheet ............................................................................................................................................. 57
11. Maintenance............................................................................................................................................................ 58
11.1. Troubleshooting................................................................................................................................................ 58
11.2. Maintenance ....................................................................................................................................................... 58
12. Dismantling and disposal................................................................................................................................... 59
13. Warranty terms and conditions ...................................................................................................................... 60
14. Appendix A –Wallbox settings ........................................................................................................................ 61
15. Appendix B –Meter settings............................................................................................................................. 64

Solo documento principale.
5/67
Identification: MD-AL-GI-00
Rev. 1.2 07.06.21 - Application: GID
Connext User Manual
Rev. 2.2 10/01/2023
Preface
General information
Please read this manual carefully before installation, use or maintenance. This manual contains
important safety instructions that must be followed during installation and maintenance of the
system.
Scope
This manual describes the assembly, installation, electrical connections, commissioning,
maintenance and troubleshooting of the Connext system. Keep this manual so that it is accessible at
all times.
Recipients
This manual is intended for qualified technical personnel (installers, technicians, electricians,
technical support personnel or anyone who is qualified and certified to work on an electrical system),
responsible for installation and start-up of the system. The manual is also intended for end users
who can find useful information on how to manage their installation via the Connext system.
Symbols used
This manual provides information for safe operation and uses certain symbols to ensure the safety
of personnel and materials, and for efficient use of the equipment during normal operation.
It is important to understand this information to prevent accidents and damage to property. Please
take note of the following symbols used in this manual.
Danger: indicates a hazardous situation which, if not resolved or
avoided, could result in serious personal injury or death
Danger
Warning: indicates a hazardous situation which, if not resolved or
avoided, could result in serious personal injury or death
Warning

Solo documento principale.
6/67
Identification: MD-AL-GI-00
Rev. 1.2 07.06.21 - Application: GID
Connext User Manual
Rev. 2.2 10/01/2023
Caution: indicates a hazardous situation which, if not resolved or
avoided, could result in minor or moderate personal injury
Caution
Attention: indicates a potentially hazardous situation which, if not
resolved or avoided, could result in damage to the system or other
property
Attention
Note: provides important tips on correct and optimal operation of
the product
Note

Solo documento principale.
7/67
Identification: MD-AL-GI-00
Rev. 1.2 07.06.21 - Application: GID
Connext User Manual
Rev. 2.2 10/01/2023
1. Preliminary safety instructions
If you have problems or questions in reading and understanding the
following information, please contact Zucchetti Centro Sistemi S.p.A.
through the appropriate channels.
Note
1.1. Safety instructions
This section highlights the main safety instructions to be followed during installation and use of the
equipment.
Before installing and using the equipment, make sure you read and understand the instructions in
this manual and familiarise yourself with the relative safety symbols shown in this chapter.
According to national and local requirements, permission must be obtained from your local provider
before connecting to the electrical grid. All connections must be carried out by a qualified electrician.
All installation operations must be carried out by a qualified and competent electrician.
Contact the nearest authorised service centre for any repairs or maintenance. Contact your
distributor for information on the nearest authorised service centre. DO NOT carry out repairs
yourself, as this may result in injury or damage.
Qualified personnel
Ensure that the operator has the necessary skills and training to operate the equipment. Personnel
responsible for use and maintenance of the equipment must be qualified and capable of performing
the activities described, and must also have adequate knowledge on how to correctly interpret the
contents of this manual. For safety reasons, this system must only be installed by a qualified
electrician with the necessary training and/or skills and knowledge. Zucchetti Centro Sistemi S.p.A.
declines all responsibility for damage to property or personal injury caused by incorrect use of the
device.
Do not attempt in any way to repair or replace components of the system without the assistance of
qualified personnel.
Installation requirements
Install and start the system according to the following instructions. Choose a suitable location for
installation of the electrical equipment. Make sure there is sufficient space to accommodate future
maintenance work.

Solo documento principale.
8/67
Identification: MD-AL-GI-00
Rev. 1.2 07.06.21 - Application: GID
Connext User Manual
Rev. 2.2 10/01/2023
Figure 1 –Do not lose or damage this manual
Transport requirements
If there are any problems with the packaging that could cause damage to the system or if there is
visible damage, notify the transport company immediately. If necessary, request assistance from an
installer or from Zucchetti Centro Sistemi S.p.A. Transport of the equipment, especially by road, must
be carried out with vehicles suitable to protect the components (especially the electronic
components) against violent knocks, humidity, vibrations, etc.
Electrical connections
Please follow all the current electrical regulations concerning accident prevention.
Before connecting the power supply, make sure to properly
disconnect the voltage on the AC connection cables.
Danger
All installation operations must be carried out by a professional
electrician, who
is prepared and has read this manual carefully and understands its
contents.
Warning
Do not remove the information label or tamper with the system.
Otherwise, ZCS will not provide any warranty or assistance.
Note

Solo documento principale.
9/67
Identification: MD-AL-GI-00
Rev. 1.2 07.06.21 - Application: GID
Connext User Manual
Rev. 2.2 10/01/2023
Operation
Do not use the product if it has any defects, cracks, scratches or leaks, but contact your dealer or ZCS
technical service.
Contact with the electrical grid or the terminal of the equipment
may cause electrocution or fire!
• Do not touch the terminal or the conductor connected to the
electrical grid.
• Follow all the instructions and safety requirements relating to grid
connection
Danger
If the system is not functioning properly:
• Disconnect the input and output power supply
Warning
Maintenance and repair
Keep the system clean and dry; if you need to clean it, use a clean dry cloth.
1.2. Symbols and icons
Introduces the main safety symbols on the Connext system. Some safety-related symbols are located
on the device. Before installation, it is important to read and understand the contents of the symbols.
Complies with the European Directives (CE)
Class II equipment
Table 1 –Symbols on the System
’Smin"“’"
There is residual voltage in the inverter! Before opening the equipment,
wait five minutes to ensure that the capacitance has been completely
discharged.
Be careful of high voltage.
Be careful of high temperature.
Complies with European standards.
Ground connection point.
This indicates the allowed temperature range.

Solo documento principale.
10/67
Identification: MD-AL-GI-00
Rev. 1.2 07.06.21 - Application: GID
Connext User Manual
Rev. 2.2 10/01/2023
Labels
Figure 2 - Labels on the System