Zepco MDVR User manual

Installation Caution: This device must be installed in a horizontal position.
GettingStarted
Embedded/MobileDigitalVideoRecorderseries
TIP Support 12V/3A-5A or 24V/3A. There are 3 cables of the
Power Input (Yellow, Red and Black). The yellow
one is used for signals, used to connect to the car’s
ignition if MDVR is installed in the car. Engine is on or off
the car by turning the Key. If you test the MDVR in the
lab, you need to make the yellow cable and the red cable
of the power short circuit, so the MDVR will start.
Power
R
equi
r
ements
MDVRInstallationlayout
-3-
1. To reduce risk of fire and electronic shock, do not expose
this appliance to rain or moisture. Do not expose this device
with direct sunshine and keep away from high temperature.
2. Do not remove cover. No user-serviceable parts inside.
Refer servicing to qualified service personnel.
3. The information in this getting start was current when
published. The manufacturer reserves the right to revise and
improve its products. All specifications are therefore subject
to change without notice.
4. This device should be installed in a horizontal position.
hank you for choosing our products. Please read these Instructions
carefully so you will know how to operate your MDVR properly.
After you have finished reading, please keep this document in a safe place
T
for future reference.
TIP 1. Hitachi Brand 2.5ͳand Seagate mobile anti-vibration
and shock resistance HDD are recommended
2. Compactable Flash Card:
Kingston Brand is recommended
HDD and
CF card
TIP
NOTE The GPS antenna MUST be hypaethral (on the roof of the
vehicle), and should be horizontal and airward to make
sure the signal can be received.
GPS
-1- -2-

InputBridalDB37(Video/AudioIN/SensorInput)
Label Description
V1/ V2/ V3/ V4 Video input for camera number 1/2/3/4
V5 / V6 / V7/ V8 Video input for camera number 5/6/7/8
A
1/
A
2/
A
3/A4
A
udio input for camera number 1/2/3/4
A
5 /A6 /A7 /A8
A
udio input for camera number 5/6/7/8
Color coded wire Description
Sen 1-8 (Red) Sensor 1-8 (0~36 V) input
A
/D
–
IN2(Green) Enable theAnalog to Digital input
Sensor-INV Connect with Speed Sensor
4
Onl
y
for 8ch
Onl
y
for 8ch
OutputBridalDB25(Video/AudioOut/RS232/InertiaSensor/ControlPanel)
Label Description
V1 4CH Operation Interface
8CH Logo
V2 4CH Live view output
8CH Operation Interface /Live view
A
L/
A
R Left/ Right
A
udio output
VGA VGA output for controlling MDR. IR handheld is fully
functional when connected to VGAoutput
RS232A For Inertia Sensor connecting
RS232B Steering and device data output (hyperlink)
RS232C PTZ / ID card reader
RS232D Reserve for future use
4 Pins Connector for control panel connecting
2 Pins Connector for power to Inertia sensor
-5-
Recording
1. Format the HDD of the MDVR. (ǏSetupǐÎǏSystemǐÎǏHDD
Formatǐ). (Default user: 00000. Default password: 88888888)
2. Setup the schedule of recording. (ǏSetupǐÎǏScheduleǐÎDate,
Schedule)
NetworkSettingsConnectedthroughaRouter
1. Gather the following from the LAN/Router: Static IP address, Subnet mask,
Gateway.(Note: The internal IP derives from the LAN/router. IP address
MUST be unique or an unused IP address. From a computer connected to
the LAN/router type IP configuration from a command prompt. This will give
you the gateway & subnet from the LAN. Copy the gateway & subnet and
enter this information into the DVR
2. Enter the menu screen by pressing theǏSetupǐ.
3. Setup the network details. (ǏSetupǐÎǏSystemǐÎǏNetworkǐ)
4. Enter the IP Address specifically assigned for the MDR on your network.
This can be achieved using the Arrow buttons. (NOTE: IP Address is
assigned by router)
5. Enter the Mask Address assigned to your network. This can be achieved
using the Arrow buttons
6. Enter the Gateway Address assigned to your network. This can be
achieved using the Arrow buttons.
7. Exit the Menu by pressing the ǏExitǐand Reboot the MDR by powering
it down and back up.
CFCardbackuprecorder
1. Place a Compact Flash Card into the Compact Flash Reader/Writer located
next to the Hard Drive Bay on the MDR.
2. Playback (full screen) the video that you want to archive.
3. When finished the DVR will notify you with a successful message button.
4. Eject the Compact Flash Card from the Reader/Writer.
-6-
ServiceandWarranty
Thank you for buying our product. As a valued customer, you now have
access to :
1. Prompt technical support if you confront any difficulties using our products
2. Information, tips and software upgrades
3. Our warranty
To realize all the above benefits, please complete and provide some
information to your distributor by email as product registration process.
For your records
Distributor information
-7-
Model number: ……………………………………………
Serial Number: ………………………….........................
Where Purchased: …………………………………………….
Date Purchased: …………………….....................