Zephyr ESSENTIALS Monsoon I AK9228AS290 Installation guide

Use, Care, and Installation Guide
www.zephyronline.com
Model number:
Serial Number:
Date of Purchase:
Sales Dealer:
MAR12.0201 © 2012 Zephyr Ventilation
Monsoon I
AK9228AS
AK9234AS
AK9228AS290
AK9234AS290
READ AND SAVE THESE INSTRUCTIONS

www.zephyronline.com

1
SAFETY NOTICE.......................................................................... 2-3
LIST OF MATERIALS................................................................. 4
INSTALLATION
Ducting Calculation Sheet....................................... 5
Mounting Height & Clearance................................ 6
Ducting Options........................................................... 7
Specifications ............................................................... 8
Electrical ......................................................................... 9
Cabinet Preparation & Installation....................... 10
Vertical Ducting Preparation................................... 11
Horizontal Ducting Preparation............................. 12-14
FEATURES & CONTROLS
Touch Controls............................................................. 15-16
RF Remote Control.................................................... 17
MAINTENANCE
Cleaning and Installing Filters ............................... 18
Lights................................................................................ 19
TROUBLESHOOTING................................................................ 20
FAN CURVE & WIRING DIAGRAMS.................................. 21-22
LIST OF PARTS AND ACCESSORIES .............................. 23
Table of Contents

Important Safety Notice
READ AND SAVE THESE INSTRUCTIONS
2
www.zephyronline.com
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE.
WARNING
TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.
b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service
panel.
CAUTION
For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Take care when using cleaning
agents or detergents. Suitable for use in household cooking area.
WARNING
TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:
a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly
on low or medium settings.
b. Always turn hood ON when cooking at high heat or when flaming food
c. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
d. Use proper pan size. Always use cookware appropriate for the size of the surface element.
e. Keep fan, filters and grease laden surfaces clean.
f. Use high setting on hood only when necessary.
g. Don’t leave hood unattended when cooking.
h. Always use cookware and utensils appropriate for the type of and amount of food being prepared.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING:
a. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
b. NEVER PICK UP A FLAMING PAN – You may be burned.
c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
d. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate it.
2. The fire is small and contained in the area where it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards.
Including fire-rated construction.
b. Sufficient air is needed for power combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent
back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National
Fire Protection Association (NFPA) and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and
the local code authorities.
c. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
d. Ducted fans must always vent to the outdoors.
e. NEVER place a switch where it can be reached from a tub or shower.
f. Make sure the power is off before installing, wiring or maintenancing.

Important Safety Notice
3
WARNING
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
NOT FOR USE OVER AN OUTDOOR GRILL
CAUTION
To reduce risk of fire and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings,
attics, crawl spaces or garages.
OPERATION
Always leave safety grilles and filters in place. Without these components, operating blowers could catch onto hair, fingers
and loose clothing.
The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,
maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to
negligence and the warranty of the unit automatically expires due to improper maintenance.
*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.
ELECTRICAL REQUIREMENTS
Important:
Observe all governing codes and ordinances.
It is the customer’s responsibility:
- To contact a qualified electrical installer.
- To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70
latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and
all local codes and ordinances.
If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the
ground path is adequate.
Do not ground to a gas pipe.
Check with a qualified electrician if you are not sure the range hood is properly grounded.
Do not have a fuse in the neutral or ground circuit.
*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269
** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575
This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit
protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to
Electrical Diagram on product.
AK9228AS / AK9234AS - 480W, 3.9 Amps
AK9228AS290 / AK9234AS290 - 152W, 1.3 Amps
A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase
and install appropriate connector if necessary.
FEDERAL COMMUNICATION COMMISSION INTERFACE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help

List of Materials
4
www.zephyronline.com
MODELS: AK9228AS(290) AND AK9234AS(290)
PARTS SUPPLIED
1 - Liner hood body
2 - Baffle filters (3 for AK9234AS)
2 - Halogen light bulbs (pre-installed)
1 - Internal blower (pre-installed)
1 - 8” round adaptor w/damper
1 - 3 1/4” x 10” rectangular adaptor w/damper
2 - Horizontal ducting blower mount brackets
1 - Top rectangular cover plate
1 - Hardware package
HARDWARE PACKAGE CONTENTS
PARTS NOT SUPPLIED
- Ducting, conduit and all installation tools
- Cable connector (if required by local codes)
Light Bulb Removal
Suction Cup (1)
M4 x 6mm (8)
Wire Caps (3)
#8 x 1/2” (12) 3/16” x 3/8” (10)
Remote Holder (1)RF Remote Control (1)

5
Installation – Ducting Calculation Sheet
Duct pieces To t a l
Equivalent number
length x used =
3-1/ 4” x 10”
Rect.,
straight
1 Ft. x ( ) = Ft.
7”-10” Round,
straight
1 Ft. x ( ) = Ft.
3-1/ 4” x 10”
Rect.900
elbow
15 Ft. x ( ) = Ft.
3-1/ 4” x 10”
Rect.450
elbow
9 Ft. x ( ) = Ft.
3-1/ 4” x 10”
Rect.900
flat elbow
24 Ft. x ( ) = Ft.
3-1/ 4” x 10”
Rect.
wall cap
with damper
30 Ft. x ( ) = Ft.
3-1/ 4” x 10”
Rect.to
6” round
transition
5 Ft. x ( ) = Ft.
3-1/ 4” x 10”
Rect.to
6” round
transition
900elbow
20 Ft. x ( ) = Ft.
6” Round,
900elbow
15 Ft. x ( ) = Ft.
6” Round,
450elbow
9 Ft. x ( ) = Ft.
Ft.
6” Round,
straight
1 Ft. x ( ) = Ft.
Subtotal column 1 =
Duct pieces To t a l
Equivalent number
length x used =
6” Round
wall cap
with damper
30 Ft. x ( ) = Ft.
Round
wall cap
with damper
30 Ft. x ( ) = Ft.
7” - 10”
Round,
900elbow
15 Ft. x ( ) = Ft.
7” - 10”
7” - 10”
Round,
450elbow
9 Ft. x ( ) = Ft.
Ft.
Ft.
Ft.
6” Round,
roof cap
30 Ft. x ( ) = Ft.
7” - 10”
Round,
roof cap
30 Ft. x ( ) = Ft.
Subtotal column 2 =
Subtotal column 1 =
Total ductwork =
6” round to
3-1/ 4” x 10”
rect.
transition
1 Ft. x ( ) = Ft.
6” round to
3-1/ 4” x 10”
rect.
transition
900elbow
16 Ft. x ( ) = Ft.
7” round to
3 1/ 4” x 10”
rect.
transition
8 Ft. x ( ) = Ft.
7” round to
3-1/ 4” x 10”
rect.
transition
900elbow
23 Ft. x ( ) = Ft.
Maximum Duct Length: For satisfactory air movement, the
total duct length should not exceed 100 equivalent feet.

Installation – Mounting Height & Clearance
6
www.zephyronline.com
DUCTING
A minimum of 8” round or 3-1/4” x 10” rectangular
duct must be used to maintain maximum air flow
efficiency.
Always use rigid type metal ducts only. Flexible
ducts could restrict air flow by up to 50%.
Also use calculation (on page 5) to compute total
available duct run when using elbows, transitions
and caps.
ALWAYS, when possible, reduce the number or
transitions and turns. If long duct run is required,
increase duct size.
If turns or transitions are required; install as far
away from hood duct output and as far apart,
between the two as possible.
Minimum mount height between range top to hood
bottom should be no less than 26”.
Maximum mount height should be no higher than
36”.
It is important to install the hood at the proper
mounting height. Hoods mounted too low could
result in heat damage and fire hazard; while hoods
mounted too high will be hard to reach and will
lose its performance and efficiency.
If available, also refer range manufacturer’s height
clearance requirements and recommended hood
mounting height above range.
Vertical Ducting:
8” round minimum
Horizontal Ducting:
8” round or 3 1/4” x 10” rectangular minimum
DAMAGE-SHIPMENT / INSTALLATION:
• Please fully inspect unit for damage before
installation.
• If the unit is damaged in shipment, return the
unit to the store in which it was bought for
repair or replacement.
• If the unit is damaged by the customer, repair
or replacement is the responsibility of the
customer.
• If the unit is damaged by the installer (if other
than the customer), repair of replacement must
be made by arrangement between customer
and installer.
26” min.
36” max.
36”

7
WARNING FIRE HAZARD
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages.
All exhaust must be ducted to the outside.
Use single wall rigid metal ductwork only.
Fasten all connections with sheet metal screws and tape all joints with certified Silver Tape or Duct Tape.
Some Ducting Options
Installation – Ducting Options
side wall cap
w/ gravity damper side wall cap
w/ gravity damper
Soffit or crawl space
Roof Pitch w/
Flashing & Cap
8”round or
3-1/4”x10” rect.
horizontal ducting 8”round
vertical ducting
8”round
vertical ducting

8
www.zephyronline.com
Installation – Specifications
Top View
3/4 View
Back View
28-
3/8
”, 34-
3/8
”
12”
1
2
”
3”
22-
3/8
”, 28-
3/8
”
1
9
-
1
/4
”
(28”)14- 1/4 ”
(34“)17-
1/4 ”
5-
5/8
”
1-
1/2
”
C/L
Ø
7
-
3
/
4
”
(28”)9- 1/4 ”
(34“)12-
1/4 ”
2”
elec.
k/o
10-
3/4
”
(28”) 9- 1/4 ”
(34“)12-
1/4 ”
9- 7/8 ”
C/L
3-
1/4
”
5-
1/2
”
7- 3/4 ”

9
ELECTRICAL
WARNING
All Electrical work must be performed by qualified electrician or person with similar technical know
how and background.
For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use
extension cord or adapter plug with this appliance.
Follow national electrical codes or prevailing local codes and ordinances.
Electrical Supply:
This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly grounded
branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire w/
ground. Please also refer Electrical Diagram labeled on product.
Cable Lock:
A cable locking connector (not supplied) might also be required by local codes. Check with local requirements
and codes, purchase and install appropriate connector if necessary.
Installation – Electrical
Cable Lock

10
www.zephyronline.com
Installation – Cabinet Preparation & Installation
1. Remove all packing materials and protective film prior to installation.
Use caution during installation to prevent scratches or damage to the
stainless steel.
2. Cut out an opening in the bottom of the cabinet by following the
dimensions in FIG. 1. If ducting the one piece liner horizontally, also
cut out an opening in the back of the cabinet (if applicable). FIG. 2.
3. Prepare liner for installation into cabinet by following the steps on
page 11 for vertical ducting or pages 12 -14 for horizontal ducting.
Continue to Step 4 after preparation is completed.
4. Lift liner into bottom opening of cabinet and secure to interior of
cabinet using (8) #8 x 1/2” stainless steel screws; (4) screws in the
front and (4) screws in the sides. FIG. 3.
WARNING: Make sure the surface you are securing the liner to
is capable of holding the weight of AK92. Failure to do so may
cause personal injury or damage to cooking surface or counter.
5. Finalize installation of electrical and duct work. Seal duct work with
certified aluminum duct tape. Power on liner, check for leaks around
duct tape and verify proper operation.
NOTE: If access to top of liner is not available after installation,
electrical and duct work connection may need to be made prior to
installing the liner.
6. Re-install the previously removed bottom panel, side spacer panels
(if applicable), grease tray, and baffle filters.
CAUTION: At least two installers are required
due to the weight and size of the liner.
!
If possible, power up and test all functions prior to installation.
28-
1/2
” or 34-
1/2
”
1
9-
3/8
”
cut out
(AK9228) (AK9234)
9”
9 ”
C/L
CABINET BACK
8in Round
4”
11”
5-1/2”
C/L
CABINET BACK
3-1/4in x 10in Rectangular
5-1/2”
FIG. 1
FIG. 2
1/4”
1-1/8”
FIG. 3

11
1. Remove baffle filters by: 1) Pulling filter toward
front of liner. 2) Pivoting rear of filter down.
2. Remove grease tray by: 1) Pulling up on tray to
release from bottom panel. 2) Lifting tray out of
liner body.
3. (AK9228AS Only) Remove left and right side-
spacer panels by removing (2) screws from
behind each panel.
Installation – Vertical Ducting Preparation
1
2
11
2
Locking Tabs
Bottom Panel Screws
2
1
4. Remove bottom panel by: 1) Removing (2)
screws from left and right sides of bottom panel.
2) Pulling bottom panel toward front of liner to
release from locking tabs.
6. Vertical ducting preparation is complete. Refer to
page 10, step 4to complete installation.
5. Secure 8” round adaptor to top of liner by (4) M4
x 6mm screws.

12
www.zephyronline.com
1. Remove baffle filters by: 1) Pulling filter toward
front of liner. 2) Pivoting rear of filter down.
2. Remove grease tray by: 1) Pulling up on tray to
release from bottom panel. 2) Lifting tray out of
liner body.
3. (AK9228AS Only) Remove left and right side-
spacer panels by removing (2) screws from
behind each panel.
1
2
11
2
Locking Tabs
Bottom Panel Screws
2
1
4. Remove bottom panel by: 1) Removing (2)
screws from left and right sides of bottom panel.
2) Pulling bottom panel toward front of liner to
release from locking tabs.
6. Remove blower from liner by removing the (4)
3/16” x 3/8” screws from the top of the liner.
Set screws aside for later usage.
5. Disconnect blower molex plug.
Installation – Horizontal Ducting Preparation

13
Installation – Horizontal Ducting Preparation
7. Using a flat head screwdriver, remove 8” round
or 3 1/4”x10” rect. knock-out plates at the back
of the liner.
9. Place top rectangular cover plate over opening
on top of the liner. NOTE: Make sure the cover
plate tabs are on top of the cover plate as
shown. From inside the liner, secure plate to
top of liner with (2) 3/16 x 3/8 screws.
AA
B
C
C
B
8. Remove knock-outs A and B for rectangular
ducting. Remove knock outs B and C for round
ducting.
Rect.
ducting
Round
ducting
At this point, install the one piece liner
At this point, install the one piece liner
into the cabinet by following the steps
into the cabinet by following the steps
on Page 10, Step 4. After the liner
on Page 10, Step 4. After the liner
installation, continue to page 14.
installation, continue to page 14.

14
www.zephyronline.com
1
2
1
Installation – Horizontal Ducting Preparation
12. Position blower inside liner body as shown by:
1) Rest the bottom horizontal ducting bracket
on the two support clips located on the interior
back wall of the liner. 2) Pivot top horizontal
ducting bracket to meet captive nuts on interior
back wall.
13. Secure blower to captive nuts on interior
back wall of liner with (8) 3/16” x 3/8” screws,
(4) screws for each bracket. Seal any gaps
around the knock-out plate by using certified
aluminum duct tape. Plug in blower molex
plug.
Horizontal ducting preparation is now
Horizontal ducting preparation is now
complete. Refer to Page 10, Step 5 to
complete. Refer to Page 10, Step 5 to
complete installation.
complete installation.
10. (Rectangular Ducting) From inside the liner,
push 3-1/4” x 10” rectangular adaptor through
the back knock-out and secure to interior back
wall of liner with (8) M4 x 6mm screws.
10. (Round Ducting) From inside the liner, push
8” round adaptor through the back knock-out
and secure to interior back wall of liner with (4)
M4 x 6mm screws.
11. Secure (2) horizontal ducting blower brackets
to blower as shown above by using the (4)
3/16” x 3/8” screws previously removed from
Page 12, Step 6; (2) screws for each bracket.

15
Lights On/Dim/Off
5 Min Delay Off
Display (speed level, delay off, filter clean)
Adjust 6 Speed Levels
Blower On/Off
1. Blower On/Off
By pressing the blower is switched on and off. When switched on, the blower starts up on speed level 1.
2. Speed Selection
The 6 speed levels are selected by pressing to decrease and to increase speed levels. The display indicates levels
selected.
3. Delay Off
This feature is used for programmed shut down of blower 5 minutes after the function is activated. Press once, a dot
flashes in the lower right side of display indicating the function is on. The blower will completely shut down after 5
minutes.
4. Lights On/Dim/Off
Switch lights on by pressing once, press a second time to dim and again to shut off lights.
5. Display Window
The display window indicates speed levels and features such as baffle filter clean reminder, delay off and clean air indicator.
Features & Controls – Touch Controls

Features & Controls – Touch Controls
16
www.zephyronline.com
Baffle Filter Clean Reminder
A set of baffle filters are fitted by the factory, these baffle filters are intended to filter out residue from
cooking. The filters need not be replaced on a regular basis but are required to be kept clean. The Baffle-
Filter Clean reminder function in the microprocessor will automatically indicate by a flashing when the
baffle filters need to be cleaned after every 30 hours of use. Filters can be cleaned by hand with non-
abrasive soap or in a dishwasher. Heavily soiled filters should also be soaked in grease cutting detergent
prior to cleaning.
Baffle Filter Clean Indicator
When flashes on the display, the baffle filters
needo be cleaned. This will occur after every 30
hours of use.
Reset the filter clean reminder timer after filters are
cleaned and re-installed. With hood off, press and
hold for approximately 5 seconds until on
display disappears . The filter clean reminder
function is now reset and a new 30 hours elapse
cycle is initiated.
F
Clean Filters
display < F > flashes
F
hold 5 sec. display from < F > to < >
To Reset
F
A
hold 5 sec. display from < A > to < >
To Disable
hold 5 sec.
To Enable
F
F
display < A > flashes
A
A 1 A 1
Clean Air Indicator
While Clean Air is active, the display will alternate
between , , , .
After 10 minutes of Clean Air operation, the blower
will power off and the 4 hour timer will reset.
If the blower speed is changed while the Clean Air
Function is in use, the cycle will be interrupted and
the timer will reset after.
Clean Air Function
Clean Air is a feature that turns on the blower on low speed every 4 hours for 10 minutes to remove stagnant
air in the kitchen. The Clean Air function is disabled by default and must be enabled by the user.

17
RF REMOTE MAINTENANCE:
Clean the remote control using non abrasive detergents
Follow instructions below for replacing battery.
Using a small flat head screwdriver, raise the cover of the battery
door (A) in order to access the battery compartment. FIG. 5.
Remove the battery and replace with battery type A23 12V.
Negative end of battery should face the spring inside the remote.
Re-install battery door and recycle old battery.
Blower On / Speed Selection
Press to power on blower and cycle through all six blower speeds.
Blower On / Power Off
By pressing , the blowers will power on at the last speed setting. Press
again and the entire hood will power off, including lights.
Delay Off
Lights On / Dim / Off
Switch lights On by pressing once, again to dim and again to switch Off.
Blower On/
Speed Selection 1
1
2
3
4
Blower On/
Power Off
2
5 Min Delay Off 3Lights On/Dim/Off
4
By pressing , the blower and lights will enter Delay Off mode. A dot will
appear in the lower right corner of the liner display indicating the function i
s
on. The blower will change to speed 1 and shut down after 5 minutes.
A
-
+
RF REMOTE FEATURES:
The RF remote control is equipped with a magnet on the back for easy
storage. The remote may be placed on any magnetic surface such as a
refrigerator or the Zephyr remote holder, FIG. 4. The remote holder can
be inserted into a standard electrical outlet for easy storage. Note: The
remote holder does not charge the RF remote.
Maximum remote control communication distance is 15 feet from the liner.
SYNCHRONIZATION: To create a unique link between your liner and remote control please follow these steps:
1. With liner off, press and hold the “lights” button on the liner until the letter “F” shows on the display screen.
2. Press the “lights” button on the remote, the lights on the liner will turn on and synchronization is complete.
Features & Controls – RF Remote Control
FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compli-
ance could void the user’s authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer
or peripheral device. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause
undesired operation.
RF REMOTE FUNCTIONS:
This remote control may operate in humid environments, but not when placed on a wet surface.
FIG. 4
FIG. 5

Maintenance – Cleaning and Installing Filters
18
www.zephyronline.com
SURFACE MAINTENANCE:
Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent,
or steel wool/ scoring pads which will scratch and damage surface. Do not use products containing chlorine
bleach or orange cleaners.
For heavier soil use liquid degreaser.
After cleaning, you may use non-abrasive stainless steel polish/ cleaners, to polish and buff out the stainless
luster and grain. Always scrub lightly using a micro fiber or clean cotton cloth and with the grain.
Cleaning the Baffle Filters
The filters are intended to trap residue and grease from cooking. Although the filters should never need
replacing, they are required to be cleaned every 30 days or when the Clean Filter Indicator is illuminated on
the liner controls .
Filters may be placed in dishwasher at low heat or soaked in hot soapy water Dry filters and re-install before
using hood.
Installing the Baffle Filters, FIG. 6:
1. Place filter into top groove of the liner as shown and
pull towards front of liner using handles.
2. Pivot back of filter upwards so it is angled in the liner.
3. Push filter into channel on back of liner to lock into place.
Replacing the Baffle Filters:
Hood Model: Part No. Qty. to Order
AK9228AS / AK9234AS 50210013 (large) 2
AK9234AS 50210017 (small) 1
Cleaning the Grease Tray
The grease tray is intended to catch residue and grease that may drip from the baffle filters. The grease tray
should be cleaned when baffle filters are cleaned. Clean the grease tray by soaking in hot soapy water and
gently scrubing any residue off with a soft terry cloth. Dry grease tray and re-install before using hood.
Removing the Grease Tray
Grease tray has a hooked lip that attaches to bottom panel top edge.
Remove grease tray by:
1. Pull up on tray to release from bottom panel. FIG. 7-1
2. Pull tray out of liner body. FIG. 7-2
1
2
11
2
FIG. 6
FIG. 7
F