Zephyr Okeanito COK-E36BSX Installation guide

Use, Care, and Installation Guide
www.zephyronline.com
Model number:
Serial Number:
Date of Purchase:
Sales Dealer:
MAR16.0201 © Zephyr Ventilation LLC.
READ AND SAVE THESE INSTRUCTIONS
Okeanito
COK-E36BSX
COK-E42BSX
COK-E48BSX

www.zephyronline.com

1
SAFETY NOTICE................................................................. 2-3
LIST OF MATERIALS....................................................... 4
INSTALLATION
Ducting Calculation Sheet....................................... 5
Mounting Height & Clearance................................ 6
Ducting Options........................................................... 7
+RRG6SHFL¿FDWLRQV ................................................... 8
Preparing the Electrical Wires............................... 9
Internal Blower............................................................. 10
Remote Blower Preparation................................... 11
Mounting the Range Hood...................................... 12-13
FEATURES & CONTROLS
Touch Controls............................................................. 14
Features.......................................................................... 15
MAINTENANCE
Cleaning and Installing Filters............................... 16
TROUBLESHOOTING................................................................ 17
WIRING DIAGRAMS................................................................... 18-19
LIST OF PARTS AND ACCESSORIES.............................. 20
WARRANTY.................................................................................... 21
PRODUCT REGISTRATION.................................................... 22
Table of Contents

Important Safety Notice
READ AND SAVE THESE INSTRUCTIONS
2
www.zephyronline.com
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.
b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service
panel.
CAUTION
For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Take care when using cleaning
agents or detergents. Suitable for use in household cooking area.
WARNING
TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:
a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly
on low or medium settings.
E $OZD\VWXUQKRRG21ZKHQFRRNLQJDWKLJKKHDWRUZKHQÀDPLQJIRRG
F &OHDQYHQWLODWLQJIDQVIUHTXHQWO\*UHDVHVKRXOGQRWEHDOORZHGWRDFFXPXODWHRQIDQRU¿OWHU
d. Use proper pan size. Always use cookware appropriate for the size of the surface element.
H .HHSIDQ¿OWHUVDQGJUHDVHODGHQVXUIDFHVFOHDQ
f. Use high setting on hood only when necessary.
g. Don’t leave hood unattended when cooking.
h. Always use cookware and utensils appropriate for the type of and amount of food being prepared.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING:
D 6027+(5)/$0(6ZLWKDFORVH¿WWLQJOLGFRRNLHVKHHWRUPHWDOWUD\WKHQWXUQRIIWKHEXUQHU%(&$5()8/7235(9(17%8516
,IWKHÀDPHVGRQRWJRRXWLPPHGLDWHO\(9$&8$7($1'&$//7+(),5('(3$570(17
b. NEVER PICK UPA FLAMING PAN – You may be burned.
c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
d. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate it.
 7KH¿UHLVVPDOODQGFRQWDLQHGLQWKHDUHDZKHUHLWVWDUWHG
 7KH¿UHGHSDUWPHQWLVEHLQJFDOOHG
 <RXFDQ¿JKWWKH¿UHZLWK\RXUEDFNWRDQH[LW
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
D ,QVWDOODWLRQZRUNDQGHOHFWULFDOZLULQJPXVWEHGRQHE\TXDOL¿HGSHUVRQVLQDFFRUGDQFHZLWKDOODSSOLFDEOHFRGHVDQGVWDQGDUGV
,QFOXGLQJ¿UHUDWHGFRQVWUXFWLRQ
E 6XI¿FLHQWDLULVQHHGHGIRUSRZHUFRPEXVWLRQDQGH[KDXVWLQJRIJDVHVWKURXJKWKHÀXHFKLPQH\RIIXHOEXUQLQJHTXLSPHQWWRSUHYHQW
back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National
)LUH3URWHFWLRQ$VVRFLDWLRQ1)3$DQGWKH$PHULFDQ6RFLHW\IRU+HDWLQJ5HIULJHUDWLRQDQG$LU&RQGLWLRQLQJ(QJLQHHUV$6+5$(DQG
the local code authorities.
c. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
d. Ducted fans must always vent to the outdoors.
e. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFI
*URXQG)DXOW,QWHUUXSWHUSURWHFWHGEUDQFKFLUFXLW
g. NEVER place a switch where it can be reached from a tub or shower.
h. Make sure the power is off before installing, wiring or maintenancing.

Important Safety Notice
3
WARNING
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
NOT FOR USE IN OUTDOOR COOKING ENVIRONMENTS.
CAUTION
7RUHGXFHULVNRI¿UHDQGWRSURSHUO\H[KDXVWDLURXWVLGH'RQRWYHQWH[KDXVWDLULQWRVSDFHVZLWKLQZDOOVFHLOLQJV
attics, crawl spaces or garages.
OPERATION
$OZD\VOHDYHVDIHW\JULOOHVDQG¿OWHUVLQSODFH:LWKRXWWKHVHFRPSRQHQWVRSHUDWLQJEORZHUVFRXOGFDWFKRQWRKDLU¿QJHUV
and loose clothing.
The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,
maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to
negligence and the warranty of the unit automatically expires due to improper maintenance.
*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.
ELECTRICAL REQUIREMENTS
Important:
Observe all governing codes and ordinances.
It is the customer’s responsibility:
 7RFRQWDFWDTXDOL¿HGHOHFWULFDOLQVWDOOHU
- To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70
latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and
all local codes and ordinances.
,IFRGHVSHUPLWDQGDVHSDUDWHJURXQGZLUHLVXVHGLWLVUHFRPPHQGHGWKDWDTXDOL¿HGHOHFWULFLDQGHWHUPLQHWKDWWKH
ground path is adequate.
Do not ground to a gas pipe.
&KHFNZLWKDTXDOL¿HGHOHFWULFLDQLI\RXDUHQRWVXUHWKHUDQJHKRRGLVSURSHUO\JURXQGHG
Do not have a fuse in the neutral or ground circuit.
*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269
** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575
This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit
protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to
Electrical Diagram on product.
$FDEOHORFNLQJFRQQHFWRUQRWVXSSOLHGPLJKWDOVREHUHTXLUHGE\ORFDOFRGHV&KHFNZLWKORFDOUHTXLUHPHQWVSXUFKDVH
and install appropriate connector if necessary.
COK-E36BSX, COK-E42BSX w/CBI-290A - MAX 170 Watts, 1.4Amps
COK-E36BSX, COK-E42BSX w/CBI-600A - MAX 400 Watts, 3.3Amps
COK-E36BSX, COK-E42BSX w/CBE-1000 - MAX 795 Watts, 6.7 Amps
COK-E36BSX, COK-E42BSX w/PBN-1000A - MAX 645 Watts, 5.4Amps
COK-E48BSX w/CBI-290A - MAX 182 Watts, 1.5Amps
COK-E48BSX w/CBI-600A - MAX 412 Watts, 3.4Amps
COK-E48BSX w/CBE-1000 - MAX 807 Watts, 6.8 Amps
COK-E48BSX w/PBN-1000A - MAX 657 Watts, 5.5Amps

List of Materials
4
www.zephyronline.com
MODEL: COK-E36BSX, COK-E42BSX, COK-E48BSX
1 - Hood
%DIÀH¿OWHUIRU´PRGHO
:=HSK\U%ORRP/('OLJKWEXOEVIRU´PRGHO
2 - 40W Mood Light Bulbs
2 - Telescopic Duct Covers
1 - Duct Cover Ceiling Bracket
1 - Utensil Rail
1 - Wall Mount Hanging Bracket
´5RXQG6WDUWLQJ&ROODUZ'DPSHU
1 - Remote Blower Wire Harness
1 - Hardware Packet
M4 * 1-1/2” x 10 M4 * 8 x 10
zip tie x 4 zip tie holder x 4
wire cap x 3 allen key x 1
washer x 10
set screw x 3
(pre-installed into
untensil rail)
Parts Not Supplied
- Ducting, conduit and all installation tools
&DEOHFRQQHFWRULIUHTXLUHGE\ORFDOFRGHV
,QWHUQDO%ORZHU.LWV&%,$&%,$
([WHUQDO%ORZHU.LW&%(
,Q/LQH%ORZHU.LW3%1$
- Duct Cover Extension Accessory
Internal Blower Packet Contents
M4 * 8 x 2
M4 * 8 x 2
10x3/16” x 2
M4 * 16 x 4
Hardware Packet Contents

5
Duct pieces To t a l
Equivalent number
length x used =
3-1/4” x 10”
Rect.,
straight
1 Ft. x ( ) = Ft.
3-1/4” x 10”
Rect.to
6” round
transition
5 Ft. x ( ) = Ft.
3-1/4” x 10”
Rect.to
6” round
transition
900 elbow
20 Ft. x ( ) = Ft.
6”, 7”, 8”, 10”
Round,
900
15 Ft. x ( ) = Ft.
6”, 7”, 8”, 10”
Round,
450
9 Ft. x ( ) = Ft.
Ft.
6”, 7”, 8”, 10”
Round,
straight
1 Ft. x ( ) = Ft.
Subtotal column1 =
Duct pieces To t a l
Equivalent number
length x used =
6”, 7”, 8”, 10”
Round, wall
cap with
damper
30 Ft. x ( ) = Ft.
Ft.
Ft.
Ft.
6”, 7”, 8”, 10”
Round
roof cap
30 Ft. x ( ) = Ft.
Subtotal column2 =
Subtotal column1 =
Total ductwork =
MaximumDuct Length:For satisfactory air movement,
the total duct length
should not exceed 100 equivalent feet.
6” roundto
3-1/4” x 10”
rect.
transition
1 Ft. x ( ) = Ft.
6” roundto
3-1/4” x 10”
rect.
transition
900 elbow
16 Ft. x ( ) = Ft.
7” roundto
3 1/4” x 10”
rect.
transition
8 Ft. x ( ) = Ft.
7” roundto
3-1/4” x 10”
rect.
transition
900 elbow
23 Ft. x ( ) = Ft.
elbow
elbow
7” to 6” or
8” to 7” Round
tapered
reducer
25 Ft. x ( ) = Ft.
3-1/4” x 10”
Rect.900
elbow
15 Ft. x ( ) = Ft.
3-1/4” x 10”
Rect.450
elbow
9 Ft. x ( ) = Ft.
3-1/4” x 10”
Rect.900
flat elbow
24 Ft. x ( ) = Ft.
3-1/4” x 10”
Rect.
wallcap
with damper
30 Ft. x ( ) = Ft.
Ft. x ( ) = Ft.
15
6”, 7“, 8”
Round
in-line
damper
Installation – Ducting Calculation Sheet

Installation – Mounting Height & Clearance
6
www.zephyronline.com
DUCTING
$PLQLPXPRI´URXQGGXFWZRUNPXVWEHXVHGWR
PDLQWDLQPD[LPXPDLUÀRZHI¿FLHQF\ZLWKWKH
FIPLQWHUQDOEORZHU$PLQLPXPRI´WR´URXQGGXFW
work must be used with the 1000 cfm remote blower.
Always use rigid type metal ducts only. Flexible ducts
FRXOGUHVWULFWDLUÀRZE\XSWR
8VHFDOFXODWLRQRQSDJHWRFRPSXWHWRWDODYDLODEOH
duct run when using elbows, transitions and caps.
ALWAYS, when possible, reduce the number or
transitions and turns. If long duct run is required,
LQFUHDVHGXFWVL]HIURP´WR´RU´,IDUHGXFHU
is used, install a long reducer instead of a pancake
reducer. Reduce duct size as far away from opening as
possible.
If turns or transitions are required; install as far
away from opening and as far apart, between 2, as
possible.
Minimum mount height between range top and hood
ERWWRPVKRXOGEHQROHVVWKDQ´
0D[LPXPPRXQWKHLJKWVKRXOGEHQRKLJKHUWKDQ´
It is important to install the hood at the proper
mounting height. Hoods mounted too low could
UHVXOWLQKHDWGDPDJHDQG¿UHKD]DUGZKLOHKRRGV
mounted too high will be hard to reach and will lose
LWVSHUIRUPDQFHDQGHI¿FLHQF\
If available, also refer to range manufacturer’s height
clearance requirements and recommended hood
mounting height above range.
Vertical Ducting:
´URXQGPLQLPXPLQWHUQDOEORZHU
´WR´URXQGPLQLPXPUHPRWHEORZHU
Horizontal Ducting:
N/A
DAMAGE-SHIPMENT / INSTALLATION:
 3OHDVHIXOO\LQVSHFWXQLWIRUGDPDJHEHIRUH
installation.
 ,IWKHXQLWLVGDPDJHGLQVKLSPHQWUHWXUQWKHXQLW
to the store in which it was bought for repair or
replacement.
 ,IWKHXQLWLVGDPDJHGE\WKHFXVWRPHUUHSDLURU
replacement is the responsibility of the customer.
 ,IWKHXQLWLVGDPDJHGE\WKHLQVWDOOHULIRWKHU
WKDQWKHFXVWRPHUUHSDLURIUHSODFHPHQWPXVW
be made by arrangement between customer and
installer.
26” min.
36” max.
min. A
max. B
min. C
max. D
Standard Extension
Hood Heights Duct Cover Duct Cover
minimum (A) 30-1/2” 44“
maximum (B) 49-1/2” 77”
Ceiling Heights
minimum (C) 92-1/2” (7’ 8-1/2”) 106“ (8 10”‘)
maximum (D) 121-1/2” (10’ 1-1/2“) 149” (12’ 5”)
36”

7
WARNING FIRE HAZARD
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages.
All exhaust must be ducted to the outside.
Use metal ductwork only.
)DVWHQDOOFRQQHFWLRQVZLWKVKHHWPHWDOVFUHZVDQGWDSHDOOMRLQWVZLWKFHUWL¿HG6LOYHU7DSHRU'XFW7DSH
Some Ducting Options
Installation – Ducting Options
Soffit or crawl space
Roof Pitch w/
Flashing & Cap
External
Blower
External
Blower
Soffit or crawl space
Side Wall
Cap

8
www.zephyronline.com
Installation – +RRG6SHFL¿FDWLRQV
Front View Bottom View
Top View Side View
95°
22-3/4”
Standard Duct Cover
min. : 30-1/2”
max. : 49-1/2”
Z1C-00OK Extension
min. : 44”
max. : 77”
6”
10”
5-1/8”
4-1/4”
(36”) 26-1/16”
(42“) 26-1/16”
(48“) 41”
21”
(36”) 5”
(42“) 8”
(48“) 3-1/2”
duct cover
C/L
6” collar C/L 8” collar C/L
19-3/4”
19-3/4”
14-1/2”
36”, 42”, 48”
10”
13-1/2”

9
ELECTRICAL
WARNING
$OO(OHFWULFDOZRUNPXVWE\SHUIRUPHGE\TXDOL¿HGHOHFWULFLDQRUSHUVRQZLWKVLPLODUWHFKQLFDONQRZ
how and background.
For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use
extension cord or adapter plug with this appliance.
Follow national electrical codes or prevailing local codes and ordinances.
Electrical Supply:
This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly grounded
branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire w/
ground. Please also refer Electrical Diagram labeled on product.
Cable Lock:
$FDEOHORFNLQJFRQQHFWRUQRWVXSSOLHGPLJKWDOVREHUHTXLUHGE\ORFDOFRGHV&KHFNZLWKORFDOUHTXLUHPHQWV
and codes, purchase and install appropriate connector if necessary.
Installation – Preparing the Electrical Wires
remote blower
knockout
electrical
knockout
7/8” 1-7/8”
9-15/16”
C/L

10
www.zephyronline.com
INTERNAL BLOWER PREPARATION
1. Position internal blower inside hood body so
LQWHUQDOEORZHUFROODUSURWXUGHVWKRXJK´URXQG
ÀDQJHRSHQLQJ
6HFXUHLQWHUQDOEORZHUWRLQWHUQDOEORZHUÀDQJH
E\0VFUHZVIURPLQWHUQDOEORZHU
hardware.
3. Position capacitor box inside hood body and
VHFXUHE\0VFUHZVIURPLQWHUQDOEORZHU
hardware.
4. Secure ground wire from capacitor box to
ground wire rivet nut next to capacitor box.
5. Connect 9 pin molex connector from internal
motor to 9 pin molex connector from capacitor
box cable. Secure cable to hood interior with zip
tie and zip tie holder.
6. Connect 6 pin molex connector from control
board box to 6 pin molex connector from
capacitor box cable. Secure cable to hood
interior with zip tie and zip tie holder.
Installation – Internal Blower

11
Installation – Remote Blower Preparation
3. Install threaded cable lock and remote blower
wiring harness through the remote blower
ZLULQJNQRFNRXW$WWDFKE\0VFUHZV
5. Connect 6 pin male connector from remote
blower wiring to 6 pin female connector on
control board box.
REMOTE BLOWER PREPARATION
 5HPRYHLQWHUQDOEORZHUÀDQJHSODWH  ,QVWDOOUHPRWHEORZHU´URXQGFROODU$WWDFKE\
0VFUHZV
NOTE: For instructions on mounting the remote
blower please refer to the CBE-1000 or PBN-
1000A remote blower manual included in the
remote blower packaging or on our website at
www.zephyronline.com
4. Secure ground wire from remote blower wiring
to ground wire rivet nut.

12
www.zephyronline.com
gap between
bracket and
wall
Top
Bottom
 0HDVXUHIURPFRRNLQJVXUIDFHWRGHVLUHGKRRGERWWRPOHYHODQGPDUNOLQH$´PLQXPXPIURPFRRNLQJ
VXUIDFH
2. Plum and mark center line.
 0DUNOLQH%´XSIURPOLQH$7KLVLVWKHWRSSRVLWLRQRIWKHZDOOEUDFNHW),*
 )ROORZFHQWHUOLQHXSWRWKHFHLOLQJPHDVXUHDQGPDUNFHLOLQJEUDFNHWPRXQWOLQH&´RXWIURPWKHZDOO
onto the ceiling. FIG. 2
 0DUNFHLOLQJEUDFNHWPRXQWLQJVSUHDG´IURPFHQWHUOLQHRQOLQH&),*
6. Place duct cover ceiling bracket onto ceiling and mark inside diameter of ceiling bracket. Cut inside
GLDPHWHURIFHLOLQJEUDFNHWWR¿WWKH´RU´URXQGGXFWSLSH
7. Prepair duct work and electrical through ceiling.
 $WWDFKFHLOLQJEUDFNHWWRFHLOLQJE\0´VFUHZV:RRGEORFNLQJPD\QHHGWREHDGGHGLQVLGH
ceiling to support the weight of the upper duct cover.
9. Place and center the top of wall bracket on line B. The top of the wall bracket will have a gap between the
bracket and the wall. FIG. 3
A
min. 26”
max. 36”
C/L
14-1/2”
9-11/16”
B
C/L
Installation – Mounting the Range Hood
CAUTION: At least two installers are
required due to the weight and size of the
hood.
!
6”
C/L
8-11/16”
C
FIG. 1 FIG. 3
FIG. 2

13
remote blower
knockout
electrical
knockout
7/8” 1-7/8”
9-15/16”
C/L
$WWDFKZDOOEUDFNHWWRZDOOE\0´VFUHZVZLWKZDVKHUV127(:RRGEORFNLQJPD\QHHGWREH
added behind the drywall if no studs are present. Wall anchors may also be used but check with local codes
for compliance. Failure to use suitable wall anchors and screws to hold the weight of the hood could result in
personal injury or damage to the cooking surface or counter.
11. Lift hood onto wall bracket. The lip at the back of the hood body will rest between the wall and the top lip
RIWKHZDOOEUDFNHW6HFXUHKRRGERG\LQSODFHE\0´VFUHZVWKRXJKERWWRPVHFWLRQRILQWHULRURI
hood body. FIG. 4
12. Place telescopic duct covers on top of hood.
5XQGXFWZRUNIURPFHLOLQJWRPRWRUFROODUDQGVHDODOOMRLQWVZLWKFHUWL¿HGDOXPLQXPGXFWWDSH
14. Install electrical wiring. FIG. 5
$WWDFKXSSHULQQHUGXFWFRYHUWRFHLOLQJEUDFNHWE\0VFUHZV),*
$WWDFKXWHQVLOUDLOWRKRRGFDQRS\E\VHWVFUHZVSUHLQVWDOOHGLQWRUDLOXVLQJWKHSURYLGHGDOOHQNH\),*
$VPDOOKROHKDVEHHQSUHGULOOHGLQWRWKHFDQRS\WRSURYLGHDVWDUWLQJSRLQWWRDWWDFKWKH¿UVWXWHQVLOUDLO
SRVW$IWHUWKH¿UVWSRVWLVOLQHGXSZLWKWKHKROHJHQWO\VOLGHWKHUHVWRIWKHUDLORQWRWKHFDQRS\%HFDUHIXO
not to scratch the stainless of the canopy while installing the utensil rail.
kcaBtnorF
Set
screw
10-9/16”
Upper duct cover
attachment screw
locations
Back View
FIG. 5
FIG. 4
FIG. 6
Installation – Mounting the Range Hood

14
www.zephyronline.com
F
The standard baffle filters are required to be cleaned frequently and as recommended in order to maintain blower
efficiency. If improperly maintained, residue from cooking will sift through filters and cause damage to hood blowers and
other sensitive components; and possibly clog duct work and create a fire hazard.
Blower On/Off
Adjust 3 Speed Levels
15 Min Delay Off
Lights On/Dim/Off
Display (Speed level, Delay Off Indicator)
1
2
3
4
5
Blower On/Off
By pressing , the blower is switched On and Off. When switched on, the blower and lights turn on at the same
setting they were switched off at. When switched off the entire hood powers off, including the LED and Mood lights.
Speed Selection
The 3 speed levels are selected by pressing to decrease and to increase speed level. The
display indicates speed level selected. Pressing when the hood is off will also turn it on.
Delay Off
This is used for programmed shut down of blower and lights 15 minutes after the function is
activated. Press once, a dot displays in the lower right hand side of display indicating
the function is on. The hood will change to speed 1 and shut down after 5 minutes.
Lights On/Dim/Off
Switch lights On by pressing once, again to dim and again to switch Off.
Baffle Filter Clean Reminder
After every 30 hours of use the display will start flashing an reminding you to clean the baffle filters
from residue and possible clogs.
1
2
3
4
Display
Displays blower speed level, delay off status and filter clean/replace notification.
5
Clean Air Feature
Clean Air is a feature that turns the blower on every 4 hours for 10 minutes to remove stagnant air in
the kitchen. This feature is disabled by default and must be enabled by the user.
Mood Light On/Off
6
Mood Light On/Off
This is the master On and Off button for the mood lights. Press IN to turn on, press again to turn OFF. When the
master mood light switch is ON, pressing the button will power off the LED and mood lights. Pressing button
again will turn the LED and mood lights back on.
6
Features & Controls – Touch Controls

15
Baffle Filter Clean Reminder
Whether your hood is installed as an exhaust or purifying unit, a set if baffle filters are fitted by the factory,
These baffle filters are intended to filter out residue from cooking. They need not be replaced on a regular
basis but are required to be kept clean. The filter clean reminder function in the microprocessor will
automatically indicate by a flashing when the baffle filters need to be cleaned after every 30 hours of
use. Filters can be cleaned by hand with non-abrasive soap or in a dishwasher. Heavily soiled filters
should also be soaked in grease cutting detergent prior to cleaning.
Baffle Filter Clean Indicator
When flashes on display, the baffle filters
installed are required to be cleaned. This will occur
after every 30 hours of use.
Re-setting Function
Reset the filter clean reminder timer when filters are
cleaned and re-installed (with hood off). Press and
hold for approximately 5 seconds, the display will
appear; hold for approximately 5 seconds until on
display disappears . The filter clean reminder
function is now reset and a new 30 hours elapse
cycle is initiated.
FClean Filters
display < F > flashes
F
hold 5 sec. display from < F > to < >
To Reset
F
F
F
To enable Clean Air Feature
With hood off, press and hold for approximately 5
seconds until the display shows then .
To disable Clean Air Feature
With hood off, press and hold for approximately 5
seconds until the display shows then .
A
-
Clean Air Feature
Clean Air is a feature that turns the fan on every 4 hours for 10 minutes to remove stagnant air in the kitchen.
This feature is disabled by default and must be enabled by the user. When the clean air function is enabled,
the blower will turn on speed 1, the display will flash between and until the 10 minute cycle has
elapsed and the blower shuts down.
1
-
hold 5 sec. display from < - > to < A >
To Enable
AA
-
A
-
hold 5 sec. display from < A > to < - >
To Disable
A
Features & Controls – Features

16
www.zephyronline.com
SURFACE MAINTENANCE:
Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or
steel wool/scoring pads which will scratch and damage surface.
For heavier soil use liquid degreaser.
After cleaning, you may use non-abrasive stainless steel polish/ cleaners, to polish and buff out the stainless
OXVWHUDQGJUDLQ$OZD\VVFUXEOLJKWO\XVLQJDPLFUR¿EHURUFOHDQFRWWRQFORWKDQGZLWKWKHVWDLQOHVVVWHHOJUDLQ
6WDLQOHVV6WHHO%DIÀH)LOWHUV
7KHVWDLQOHVVVWHHOEDIÀH¿OWHUV¿WWHGE\WKHIDFWRU\DUHLQWHQGHGWRWUDSUHVLGXHDQGJUHDVHIURPFRRNLQJ
$OWKRXJKWKH¿OWHUVQHYHUQHHGUHSODFHPHQWWKH\DUHUHTXLUHGWREHFOHDQHGHYHU\GD\VRUPRUHRIWHQ
depending on cooking habits.
Filters may be placed in dishwasher at low heat or soaked in hot soapy water.
1
2
3
1
2
3
Maintenance – Cleaning and Installing Filters
,QVWDOOLQJ%DIÀH)LOWHUV
 ,QVHUW¿OWHULQPHWDOJURRYHRQERWWRPRIKRRG
3XVK¿OWHUWRZDUGVEDFNRIKRRGXVLQJ
handles.
 3LYRWIURQWRI¿OWHUXSZDUGXQWLOLWLVÀXVKZLWK
the hood.
 /RFN¿OWHULQSODFHE\SXOOLQJDZD\IURPKRRG
5HPRYLQJ%DIÀH)LOWHUV
 3XOO¿OWHUWRZDUGEDFNRIUDQJHKRRGXVLQJ
handles.
 3LYRWIURQWRI¿OWHUXSZDUG
3. Remove downwards to the rear.

17
TROUBLESHOOTING PROCEDURES FOR OKEANITO
Issue Cause What to do
After installation,
the unit doesn’t
work.
1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s
power is ON.
2. The power line and the cable locking connector
is not connecting properly. 2. Check the power connection with the unit is connected properly.
3. The switch board and control board wirings are
disconnected. 3. Make sure the wirings between the switch board and control board are connected
properly.
4. The switch board or control board is defective. 4. Change the switch board or control board.
Light works, but
blower is not
turning.
1. Wire harness from external or internal blower
might be disconnected. 1. Make sure the wires are connected to the control board box
2. Blower molex plug pin is not making contact. 2. Disconnect the blower molex plug, check pins
inside plug to see if pin is pushed inside the
plug too far. Reseat pin if needed.
3. The blower is defective, possibly seized. 3. Change the blower.
4. The thermally protected system detects if the
blower is too hot to operate and shuts the blower
down.
4. The blower will function properly after the
thermally protected system cool down.
5. Damaged capacitor. 5. Change the capacitor.
The unit is
vibrating. 1. The blower is not secure in place. 1. Tighten the blower in place.
2. Damaged blower wheel/makes noise. 2. Change the blower.
3. The hood is not secured in place. 3. Check the installation of the hood.
The unit is
whistling. $¿OWHULVQRWLQWKHFRUUHFWSRVLWLRQ $GMXVWWKH¿OWHUVXQWLOWKHZKLVWOLQJVWRSV
2. The duct pipe connections are not sealed or
connected properly. 2. Check the duct pipe connections to be sure all connections are sealed properly.
The blower is
working, but the
lights are not.
1. The light socket plug is disconnected. 1. Connect the light socket plug.
2. Defective LED bulb. 2. Change the LED bulb.
The hood is
not venting out
properly.
1. The hood might be hanging to high from the
cook top. 1. Adjust the distance between the cook top and WKHERWWRPRIWKHKRRGZLWKLQ´DQG´
range.
2. The wind from the opened windows or opened
doors in the surrounding area are affecting the
ventilation of the hood.
2. Close all the windows and doors to eliminate
WKHRXWVLGHZLQGÀRZ
3. Blocking in the duct opening or ductwork. 3. Remove all the blocking from the duct work or
duct opening.
4. There are too many turns within the ducting. 4. Limit number of turns and/or increase duct
size.
5. Using the wrong size of ducting.  &KDQJHWKHGXFWLQJWRDWOHDVW´RUKLJKHU
IRUWKHLQWHUQDOEORZHUDQG´RUKLJKHUIRUWKH
external blower.
Filter is vibrating.  %DIÀH¿OWHULVORRVH  5HPRYH¿OWHUDQGUHLQVWDOOLWRUFKDQJHWKH
EDIÀH¿OWHU
After hood has
been installed
for a period of
time, it stopped
working.
1. Control board needs to be reset. 1. Turn circuit breaker which controls the hood
off for at least 15 minutes. Turn it back on and
WKLVVKRXOG¿[WKHSUREOHP
2. Defective control board. 2. Replace control board.
Troubleshooting

18
www.zephyronline.com
Wiring Diagrams