Zest Miami User manual

Assembly Instructions
(W x D x H) 1.89m x 1.62m x 1.80m
Product Name: Miami Swing
Pressure Treated products should not be treated with any other products for the first month.
PLEASE KEEP THIS INSTRUCTION
Zest4Leisure
01352 752555 option 1 –[e-mail]
V2-02.15

Miami Swing Assembly Instructions
Requires 2 person assembly.All screw holes to be pre-drilled.
Tools required: Corded / Cordless Drill, Pozi-drive Bit / Screwdriver, 3mm Drill Bit,
Socket Set, Hammer.
Miami Swing Pack List
Item Description Quantity
A1 Front Leg 2
A2 Back Leg (with additional bolt hole for canopy) 2
B Beam 1
C Horizontal Short Brace 2
D Horizontal Long Brace 2
E Diagonal Brace 2
F Seat Back 1
G Seat 1
H Armrest Support 2
J Armrest 2
K Shelf 2
L Canopy Slats 1
M Slats Support 2
N Centre Batten 1
Fixings
30mm Screws 16
60mm Screws 34
100mm Screws 2
45mm Bolts, washers & nuts 6
100mm Bolts, washers & nuts 24
115mm Eye Bolts & small karabiner, washers & nuts 4
150mm Bolts, washers & nuts 2
150mm Eye Bolts & large karabiner, washers & nuts 2
700mm Chain 2
900mm Chain 2
www.zest4leisure.co.uk

Miami Swing Assembly Instructions
Requires 2 person assembly.All screw holes to be pre-drilled.
Tools required: Corded / Cordless Drill, Pozi-drive Bit / Screwdriver, 3mm Drill Bit,
Socket Set, Hammer.
www.zest4leisure.co.uk

Please take a few moments to check all pack contents listed.
Please contact “Zest4Leisure” directly if any of the pack contents are damaged
or missing. Contact telephone: [phone] option 1 or email:
[email protected]
Assembly requires 2 persons. All screw holes to be pre-drilled.
Tools required: Corded/Cordless Drill, Pozi-drive Bit/Screwdriver, 3mm Drill Bit,
Socket Set, Hammer.
Miami Swing is now complete.
1. Position 1no Front Leg A1 and 1no Back Leg A2 either side of Beam B (Fig.1a), align bolt
holes and attach using 1no 150mm Bolt, washer & nut (Fig.1b). Do not fully tighten at this
stage. Repeat procedure for the remaining 1no Front Leg A1 and 1no Back Leg A2 at the other
end of Beam B.
2. Position Horizontal Short Brace C (Fig.2a) and Horizontal Long Brace D (Fig.2b) onto Legs,
align bolt holes and insert 8no 100mm Bolts –4no per horizontal brace. Repeat procedure for
the remaining braces and Legs.
3. Turn over the Legs/Beam Assembly (Fig.3a), attach washers and nuts and fully tighten
(Fig.3b).
4. Attach Diagonal Brace E to Beam B using 2no 100mm Bolts, washers & nuts and fully tighten
(Fig.4a). Raise Leg Assembly, align Diagonal Brace E & Horizontal Short Brace C bolt holes
and fix in position using 1no 100mm Bolt, washer & nut (Fig.4b). Fully tighten all nuts at this
stage. Repeat procedure with the remaining Diagonal Brace E at the other end of Beam B
(Fig.4c).
5. Insert 2no 150mm Eye Bolts into the Beam B (Fig.5) and secure using washers and nuts.
6. Locate half lap joints of Seat Back F into half lap joints of Seat G and fix in position using 6no
45mm Bolts, washers & nuts –2no per joint (Fig.6b)
7. Locate the Armrest Support H dowels into the Armrest J holes (Fig.7a) and fix in position using
1no 60mm Screw (Fig.7b). Repeat procedure for the remaining Armrest Support H and Armrest
J.
8. Attach Armrest Assembly to Seat Assembly using 2no 115mm Eye Bolts as shown in Figs 8a &
8b. Repeat procedure for the remaining Arm Assembly.
9. Hook 1no Short Chain & 1no Long Chain onto Large Karabiner ensuring Short Chain is at the
back (Fig.9a). Repeat procedure for remaining chains. Attach Short Chain to the back of the
Seat Assembly (Fig.9b) and Long Chain to the front of the Seat Assembly (Fig.9c) using 2no
Small Karabiners. Repeat procedure for remaining Chains.
10. Locate Shelves K onto Long Braces D (Fig.10).
11. Place Canopy Slats L onto Slats Supports M (Fig.11a) ensuring an overhang of 45mm. Fix into
position using 32no 60mm Screws –2no per slat (Fig.11b).
12. With the Canopy assembly inverted, Position the Centre Batten N centrally, predrill screw holes
and attach using 16no 30mm Screws, 1no per canopy slat (Fig.12).
13. Position Canopy Assembly over Swing Assembly ensuring Back Legs A2 bolt holes and Slats
Supports L bolt holes are aligned. Insert 2no 100mm Bolts –1no per Back Leg A2 and attach
washers and nuts. Fix Slats Supports M to Front Legs A1 using 2no 100mm Screws–1no per
Front Leg A1.

www.zest4leisure.co.uk
1b1a
2a 2b
3a 3b
4a 4b

www.zest4leisure.co.uk
54c
6a 6b
7a 7b
8a 8b

www.zest4leisure.co.uk
9b9a
9c 10
11a 11b
12 13
All screw holes to be predrilled.